An in-fiber Mach-Zehnder interferometer for strain measurement is proposed and experimentally demonstrated. The sensor consists of a taper followed by a short section of a multi-mode fiber （MMF） and a dispersion com...An in-fiber Mach-Zehnder interferometer for strain measurement is proposed and experimentally demonstrated. The sensor consists of a taper followed by a short section of a multi-mode fiber （MMF） and a dispersion com- pensating fiber （DCF）, which is sandwiched between two single mode fibers （SMFs）. The taper is used as a fiber coupler to excite cladding modes in the SMF, and these cladding modes transmit within the MMF and the DCF. The core mode and the cladding modes interfere in the DCF SMF fusion point to form intermodal interference. A well-defined interference spectrum is obtained in the experiment. Selected interference dips are used to measure the strain changes. The experimental results show that this device is sensitive to strain with the wavelength-referenced sensitivity of 2.6 pm/με and the power-referenced sensitivity of 0. 0027 dB/με, respectively.展开更多
By using a graded-index multimode fiber （GI-MMF） with a relatively flat index profile and high refractive index of the fiber core, a microextrinsic fiber-optic Fabry Prot interferometric （MEFPI） strain sensor is f...By using a graded-index multimode fiber （GI-MMF） with a relatively flat index profile and high refractive index of the fiber core, a microextrinsic fiber-optic Fabry Prot interferometric （MEFPI） strain sensor is fabricated through chemical etching and fusion splicing. Higher reflectance of the microcavity is obtained due to the less-curved inner wall in the center of the fiber core after etching and higher index contrast between the GI-MMF core and air. The maximum reflection of the sensor is enhanced 12 dB than that obtained by etching of the Er- or B-doped fibers. High fringe contrast of 22 dB is obtained. The strain and temperature responses of the MEFPI sensors are investigated in this experiment. Good linearity and high sensitivity are achieved, with wavelength-strain and wavelength-temperature sensitivities of 7.82 pm/με and 5.01 pm/°C, respectively.展开更多
In this Letter, an alternative solution is proposed and demonstrated for simultaneous measurement of axial strain and temperature. This sensor consists of two twisted points on a commercial single mode fiber introduce...In this Letter, an alternative solution is proposed and demonstrated for simultaneous measurement of axial strain and temperature. This sensor consists of two twisted points on a commercial single mode fiber introduced by flame-heated and rotation treatment. The fabrication process modifies the geometrical configuration and refractive index of the fiber. Different cladding modes are excited at the first twisted point, and part of them are coupled back to the fiber core at the second twisted point. Experimental results show distinct sensitivities of 34.9 pm/με with 49.23 pm/℃ and -36.19 pm/με with 62.99 pm/℃ for the two selected destructive interference wavelengths.展开更多
A low carbon Nb-microalloyed high deformability pipeline steel with X100 grade has been processed by TMCP and followed two-stage cooling process.The microstructure is characterized by ferrite/bainite multiphase.The ef...A low carbon Nb-microalloyed high deformability pipeline steel with X100 grade has been processed by TMCP and followed two-stage cooling process.The microstructure is characterized by ferrite/bainite multiphase.The effective grain size is 1.85μm in average.The volume of ferrite is about 10-15% and the grains sizes are mostly less than 5μm.The bainite consists of granular-bainite and lath-bainite,with M/A islands finely dispersed.The longitudinal tensile yield strength,uniform elongation,yield ratio are 647MPa,7.6% and 0.78,respectively.Ferrite/bainite multiphase have large strain hardenability that resulting high strength and high deformability combination.Precipitation of Nb also improves the strength and uniform deformability by precipitation strengthening and grain refinement.展开更多
基金Supported by the National Natural Science Foundation of China under Grant Nos 61077006,60727004,and 61077060the China National Petroleum Corporation Science and Technology Development Projects under Grant No 2014B-4012the Science Research Plan Projects of Shaanxi Education Department under Grant No 14JK1580
文摘An in-fiber Mach-Zehnder interferometer for strain measurement is proposed and experimentally demonstrated. The sensor consists of a taper followed by a short section of a multi-mode fiber （MMF） and a dispersion com- pensating fiber （DCF）, which is sandwiched between two single mode fibers （SMFs）. The taper is used as a fiber coupler to excite cladding modes in the SMF, and these cladding modes transmit within the MMF and the DCF. The core mode and the cladding modes interfere in the DCF SMF fusion point to form intermodal interference. A well-defined interference spectrum is obtained in the experiment. Selected interference dips are used to measure the strain changes. The experimental results show that this device is sensitive to strain with the wavelength-referenced sensitivity of 2.6 pm/με and the power-referenced sensitivity of 0. 0027 dB/με, respectively.
基金supported by the State Key Laboratory of Advanced Optical Communication Systems and Networks,China
文摘By using a graded-index multimode fiber （GI-MMF） with a relatively flat index profile and high refractive index of the fiber core, a microextrinsic fiber-optic Fabry Prot interferometric （MEFPI） strain sensor is fabricated through chemical etching and fusion splicing. Higher reflectance of the microcavity is obtained due to the less-curved inner wall in the center of the fiber core after etching and higher index contrast between the GI-MMF core and air. The maximum reflection of the sensor is enhanced 12 dB than that obtained by etching of the Er- or B-doped fibers. High fringe contrast of 22 dB is obtained. The strain and temperature responses of the MEFPI sensors are investigated in this experiment. Good linearity and high sensitivity are achieved, with wavelength-strain and wavelength-temperature sensitivities of 7.82 pm/με and 5.01 pm/°C, respectively.
基金supported by the National Natural Science Foundation of China(Nos.61775070 and 61275083)the Fundamental Research Funds for the Central Universities(No.2017KFYXJJ032)
文摘In this Letter, an alternative solution is proposed and demonstrated for simultaneous measurement of axial strain and temperature. This sensor consists of two twisted points on a commercial single mode fiber introduced by flame-heated and rotation treatment. The fabrication process modifies the geometrical configuration and refractive index of the fiber. Different cladding modes are excited at the first twisted point, and part of them are coupled back to the fiber core at the second twisted point. Experimental results show distinct sensitivities of 34.9 pm/με with 49.23 pm/℃ and -36.19 pm/με with 62.99 pm/℃ for the two selected destructive interference wavelengths.
文摘A low carbon Nb-microalloyed high deformability pipeline steel with X100 grade has been processed by TMCP and followed two-stage cooling process.The microstructure is characterized by ferrite/bainite multiphase.The effective grain size is 1.85μm in average.The volume of ferrite is about 10-15% and the grains sizes are mostly less than 5μm.The bainite consists of granular-bainite and lath-bainite,with M/A islands finely dispersed.The longitudinal tensile yield strength,uniform elongation,yield ratio are 647MPa,7.6% and 0.78,respectively.Ferrite/bainite multiphase have large strain hardenability that resulting high strength and high deformability combination.Precipitation of Nb also improves the strength and uniform deformability by precipitation strengthening and grain refinement.
