Virtual strain loading method for low temperature cohesive failure of asphalt binder

Cohesive failure is one of the primary reasons for low-temperature cracking in asphalt pavements.Understanding the micro-level mechanism is crucial for comprehending cohesive failure behavior.However,previous literature has not fully reported on this aspect.Moreover,there has been insufficient attention given to the correlation between macroscopic and microscopic failures.To address these issues,this study employed molecular dynamics simulation to investigate the low-temperature tensile behavior of asphalt binder.By applying virtual strain,the separation work during asphalt binder tensile failure was calculated.Additionally,a correlation between macroscopic and microscopic tensile behaviors was established.Specifically,a quadrilateral asphalt binder model was generated based on SARA fractions.By applying various combinations of virtual strain loading,the separation work at tensile failure was determined.Furthermore,the impact of strain loading combinations on separation work was analyzed.Normalization was employed to establish the correlation between macroscopic and microscopic tensile behaviors.The results indicated that thermodynamic and classical mechanical indicators validated the reliability of the tetragonal asphalt binder model.The strain loading combination consists of strain rate and loading number.All strain loading combinations exhibited the similar tensile failure characteristic.The critical separation strain was hardly influenced by strain loading combination.However,increasing strain rate significantly enhanced both the maximum traction stress and separation work of the asphalt binder.An increment in the loading number led to a decrease in separation work.The virtual strain combination of 0.5%-80 provided a more accurate representation of the actual asphalt's tensile behavior trend.

Load Bearing Capacity and Safety Analysis for Strain-hardening Austenitic Stainless Steel Pressure Vessels

By increasing the yield strengths of austenitic stainless steels for pressure vessels with strain hardening techniques,the elastic load bearing capacity of austenitic stainless steel pressure vessels can be significantly improved.Two kinds of strain hardening methods are often used for austenitic stainless steel pressure vessels：Avesta model for ambient temperature applications and Ardeform model for cryogenic temperature applications.Both methods are obtained from conventional design rules based on the linear elastic theory,and only consider the hardening effect from materials.Consequently this limits the applications of strain hardening techniques for austenitic stainless steel pressure vessels because of safety concerns.This paper investigates the effect of strain hardening on the load bearing capacity of austenitic stainless steel pressure vessels under large deformation,based on the elastic-plastic theory.Firstly,to understand the effect of strain hardening on material behavior,the plastic instability loads of a round tensile bar specimen are derived under two different loading paths and validated by experiments.Secondly,to investigate the effect of strain hardening on pressure vessels strength, the plastic instability pressure under strain hardening is derived and further validated by finite element simulations.Further,the safety margin of pressure vessels after strain hardening is analyzed by comparing the safety factor values calculated from bursting tests,finite element analyses,and standards.The researching results show that the load bearing capacity of pressure vessels at ambient temperature is independent of the loading history when the effects of both material strain hardening and structural deformation are considered.Finite element simulations and bursting tests results show that the minimum safety factor of austenitic stainless steel pressure vessels with 5% strain hardening is close to the recommended value for common pressure vessels specified in the European pressure vessel standard.The proposed study also shows that in the strain hardening design of austenitic stainless steel pressure vessels,the calculation for plastic instability pressure could use theoretical formula or finite element analyses based on geometrical dimensions and material property parameters before strain hardening,but a 5%strain should be employed as a design limit.The proposed research can be used for the strain hardening design of austenitic stainless steel pressure vessels safely.

Characteristics of dynamic strain and strength of frozen silt under long-term dynamic loading

The dynamic swain and strength of frozen silt under long-term dynamic loading are studied based on creep tests. Three groups of tests are performed (Groups I, II, and III). The initial deviator stresses of Groups I and II are same and the dynamic stress ampli- tude of Group II is twice as that of Group I. The minimum value of dynamic stress in Group IlI is near zero and its dynamic stress amplitude is larger than those of Groups I and II. In tests of all three groups there are similar change trends of accttmulative sWain, but with different values. The accumulative swain curves consist of three stages, namely, the initial stage, the steady stage, and the gradual flow stage. In the tests of Groups I and II, during the initial stage with vibration times less than 50 loops the strain ampli- tude decreased with the increase of vibration times and then basically remained constant, fluctuating in a very small range. For the tests of Group III, during the initial and steady stages the sWain amplitude decreased with the increase of vibration times, and then increased rapidly in the gradual flow stage. The dynamic strength of frozen silt decreases and trends to terminal dynamic strength as the vibration times of loading increase.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Physical meaning and prediction efficiency of the load/unload response ratio of rocks in strain-weakening phase before failure

Rock experiment results indicate that the load/unload response ratio (LURR) of rocks expressed via strain energy may have singular or negative value after the stress in the rock reaches its maximum before rock failure or when the rock goes into the strain-weakening phase. The universality of this phenomenon is discussed. Expressed via strain or strain energy and the travel time of P wave, the variation form of the reciprocal of LURR during the process of rock failure preparation is derived. The results show that after a sharp decrease the reciprocal of LURR reaches its minimum when the main fracture of the rock is about to appear. This feature can be taken as an indication that the rock main fracture is impending.

Strain Rate Effect on the Response of Blast Loaded Reinforced Concrete Slabs

Dynamic Increase Factor (DIF) due to strain rate effect was examined with documented experimental work done by Razaqpur, et al. In the experiment work, two 1000 × 1000 × 70 mm reinforced concrete slabs were constructed. The slabs were subjected to blast loads generated by the detonation of either 22.4 kg or 33.4 kg of ANFO located at a 3.0 m standoff. Blast wave characteristics, including incident and reflected pressures and reflected impulses were measured. The slabs were modeled by explicit analysis with or without strain rate effect to study their behavior under blast load to compare their predicted and observed behavior. The predicted post-blast damage and mode of failure for each model is compared with the observed damage of experimental work. It was concluded that when the dynamic increase factor added to concrete and reinforcement materials due to strain rate effect, the behavior of model under blast load become closer to experimental work.

A semi-empirical formula for evaluating residual strain of soils under earthquake loading

A new semi-empirical formula for evaluating the residual strain of soils under earthquake loading is presented in this paper based on the incremental method and the increment model proposed by the authors.When the incident loading is uniform,the results calculated by the new formula are nearly the same as those by the existing formula.For excitation of the random earthquake loading,the results calculated by the new formula are compared to the results obtained by dynamic triaxial tests.The dynamic triaxial tests had been performed considering different seismic waves,confining stresses, consolidation ratios,and types of cohesive soils.The comparison between the calculated and tested results indicate that the presented formula can efficiently and practically describe the time-dependent process of the soil residual strains under actual seismic loads.

THE ELASTO-PLASTIC STRAIN ANALYSIS OF NOTCHED PLATE UNDER CYCLIC LOADING—AN APPLICATION OF PLASTIC ANISOTROPIC HARDENING THEORY

In order to predict the life of engineering structures, it is necessary to investigate the strain distribution in notched members. In gineral, the Uauschinger Effect of materials under cyclic loading is not negligible, and so the anisolropic hardening model has been suggested. From the comparison between the calculated and experimental results in this paper, we can see that even the linear kinematic hardening model is quite suitable for strain analysis under cyclic loading.

Analytical solution for a strained reinforcement layer bonded to lip-shaped crack under remote modeⅢuniform load and concentrated load

In this paper, the analytical solution of stress field for a strained reinforcement layer bonded to a lip-shaped crack under a remote mode III uniform load and a concentrated load is obtained explicitly in the series form by using the technical of conformal mapping and the method of analytic continuation. The effects of material combinations, bond of interface and geometric configurations on interfaciai stresses generated by eigenstrain, remote load and concentrated load are studied. The results show that the stress concentration and interfaciai stresses can be reduced by rational material combinations and geometric configurations designs for different load forms.

Analytical Solutions to Strain Rates of Reinforced Concrete Simply Supported Slabs under Blast Loads

Based on the Duhamel integral, a couple of analytical solutions are derived to predict the strain rates of concrete and steel reinforcement in reinforced concrete slabs under blast loads and to estimate their variation over depth of a cross-section along the entire length of the member. The analytical approach utilizes the single-degree-of-freedom mode for the analysis of reinforced concrete simply supported one-way panels subjected to blast loads. These analytical solutions can give the strain rate profile for any cross-section at any time and permit variations of strain rate in each time step of numerical iteration method, thus making it possible to directly incorporate strain rate effects into non-linear dynamic response analysis of structural members subjected to blast loads.

Dynamic Response of Pultruded Glass-Graphite/Epoxy Hybrid Composites Subjected to Transverse High Strain-Rate Compression Loading

In a previous study, the energy absorption and dynamic response of different combinations of cylindrical fiber-reinforced pultruded hybrid composite samples made of unidirectional glass and graphite fiber/epoxy, were investigated under longitudinal compression loading. It was found that placing glass fibers in the inner core of composites resulted in a higher ultimate compressive strength and specific energy absorption. In this study, the dynamic responses of pultruded glass-graphite/epoxy hybrid specimens with rectangular cross-section subjected to transverse compression loading are reported. Crack initiation and propagation was monitored using a high-speed video camera, and the effects of hybridization were analyzed. It was found that the location of glass or graphite fibers inside the pultruded composites has no significant effect on the ultimate compressive strength under such transverse compression loading. The energy absorption in all the hybrid specimens was almost identical. Graphite/epoxy composite showed higher specific energy absorption due to its lower density, and glass/epoxy composite had the lowest specific energy absorption.

再生粗骨料混凝土应力-应变关系

再生粗骨料混凝土应力-应变关系是实现其材料到结构力学分析的桥梁纽带,成为再生粗骨料混凝土结构基础理论的基石。介绍了作者团队多年来在再生粗骨料混凝土应力-应变关系方面取得的研究进展:采用模型化再生粗骨料方法,研究了复杂界面过渡区对再生粗骨料混凝土破坏行为的影响,揭示了再生粗骨料混凝土细观损伤本质与演化机理;从静力作用到动力作用,系统地开展了不同工况下再生粗骨料混凝土应力-应变行为试验研究,探明了载荷条件对再生粗骨料混凝土应力与变形的影响规律并建立了相适应的力学与数学模型;进一步考虑再生粗骨料性能时空变异性,发现了再生粗骨料混凝土力学响应的概率分布特征,提出了再生粗骨料混凝土随机损伤本构关系;基于获得的本构模型,完成了再生粗骨料混凝土构件时变可靠度分析和结构动力非线性分析,为再生粗骨料混凝土在实际工程中的安全应用提供了理论支撑;提炼了相关研究结论并对未来研究工作进行了展望。

Simulating the Stress-Strain Response of Building under Oscillating Wind Conditions

Wind load is one of the main lateral control loads that need to be considered in the design of high-rise building structures. It is also of great engineering significance to study the influence of static wind load or time-varying wind load on the dynamic response of structures. In this paper, a high-rise building with a rectangular section (46.8 m × 27 m × 33 m) is simulated based on Ansys18.0 APDL software. The real situation of its response under no lateral wind load and different fluctuating wind load conditions is simulated and the stress and strain response of the building under steady-state and time-varying wind load is given. The results show that the upper strain of the structure under wind load is about 1/1000 of the bottom strain, and the strain of the structure shows obvious accumulation from the top to the bottom, that is, the bottom strain of the building will be higher than the top strain. The influence of time-varying wind load on building structure is related to the loading position of wind load on the structure. The results provide a basis for the structural wind resistance design of this type of building.

ANALYSIS OF THE LOCALIZATION OF DAMAGE AND THE COMPLETE STRESS-STRAIN RELATION FOR MESOSCOPIC HETEROGENEOUS BRITTLE ROCK SUBJECTED TO COMPRESSIVE LOADS

A micromechanics-based model is established. The model takes the interaction among sliding cracks into account, and it is able to quantify the effect of various parameters on the localization condition of damage and deformation for brittle rock subjected to compressive loads. The closed-form explicit expression for the complete stress-strain relation of rock containing microcracks subjected to compressive loads was obtained. It is showed that the complete stress-strain relation includes linear elasticity,nonlinear hardening,rapid stress drop and strain softening.The behavior of rapid stress drop and strain softening is due to localization of deformation and damage. Theoretical predictions have shown to be consistent with the experimental results.

船闸浮式系船柱结构受荷敏感区域研究

随着我国水运交通事业的不断发展,大型船闸的安全运行至关重要。为保证船闸内船舶的泊稳安全,实时感知船闸浮式系船柱的运行状况至关重要。浮式系船柱受荷敏感区域的确定与结构监测传感器的布设方案密切相关,然而针对该问题仍缺乏系统的研究。依托某大型船闸工程,通过建立浮式系船柱结构三维数值模型,基于有限元方法研究浮式系船柱在不同系缆力、系缆角度情况下的结构应变路径变化规律。结果表明,浮式系船柱结构受系缆力作用的敏感区位置在靠近浮式系船柱空心圆柱体与固定钢板焊接位置附近,为浮式系船柱结构受力监测传感器的安设以及后续工作提供理论支撑。

舰载飞机着舰撞击载荷实测技术研究

针对国内飞机起落架载荷测量中普遍存在的静标动测问题,从理论和机理上分析了静标定的应变法实测动态载荷存在问题的原因。同时,考虑到舰载飞机因定点着舰方式遭受严重的动态载荷,重点研究了舰载飞机着舰撞击载荷的静标动测问题。通过动态落震试验模拟飞机着舰过程,根据测力平台的实测载荷分析,获取了应变法实测载荷精度受动态影响的程度,提出一种改进的惯性修正方法,即:通过落震试验数据辨识质量矩阵,通过辨识的质量矩阵和实测加速度修正应变法的实测载荷。试验结果表明,改进的惯性修正方法进一步提高了垂向载荷的测量精度,显著提高了航向和侧向载荷的实测精度。

Development of a Test Rig for Axial Strains Measurement in Automobile Wheel

In automobile wheel application, a test rig is vital and used to simulate conditions of the wheel in service in order to affirm the safety and reliability of the wheel. The present work designed a test rig for measuring axial strains in automobile wheel. The wheel used was a five-arm wheel (6JX14H2;ET 42) and Tyre (175 × 65 R 14). Experimental (EXP) test was carried out, with a radial load of 4750 N and inflation pressure of 0.3 MPa, to measure the axil strains which were converted to maximum principal strain values and, compared with data from Finite Element Analysis (FEA) using Creo-Element/Pro 5.0 at wheel’s contact angles of 90 degree (FEA 90 deg), 40 degree (FEA 40 deg) and 30.25 degree (FEA 30.25 deg), respectively. Results show that at the wheel’s point of contact with the ground, maximum principal strain values were highest at the inboard bead seat with a value of about 5.69 × 10-4 mm/mm, followed by the values at the well of about 5.66 × 10-4 mm/mm. The value at the outboard bead seat was least at about 2.22 × 10-4 mm/mm, which was due to the presence of spikes at this location that tends to resist imposed radial loads. However, the highest mean maximum principal strain values at the locations of inboard, well and outboard, were about 2.11 × 10-4 mm/mm, 3.78 × 10-4 mm/mm and .99 × 10-4 mm/mm, respectively. With the highest single value of about 5.69 × 10-4 mm/mm, the inboard bead seat was the most strained location of the wheel. Overall results showed that all values of maximum principal strains were below the threshold value of about 1 × 10-2 mm/mm. The values obtained for EXP and FEA could be said to be in close agreement when compared with the threshold value. With this in mind, the rig is recommended for use in related experimental procedures.

波形钢腹板工字梁的等效计算模型及稳定性分析

基于变形与应变能相等的原则,提出波形钢腹板工字梁的等效平直钢腹板计算模型。通过波形钢腹板直板段与斜板段应变分析,推导了波形钢腹板工字梁及等效计算模型的应变能,建立等效惯性矩与等效扇性惯性矩,利用平直钢腹板工字梁的临界荷载计算公式,对波形钢腹板工字梁进行稳定性分析。研究结果表明:该方法简单、便捷,对波形钢腹板工字梁的稳定分析准确、有效;建立的等效惯性矩与翘曲惯性矩仅取决于截面及波形钢板尺寸,不受工字梁的边界条件、跨径等因素的影响,具有良好的适应性。

磷石膏掺量对钢管混凝土力学性能的影响

通过正交试验研究了粉煤灰掺量(10%、15%、20%、25%)、矿粉掺量(15%、20%、25%、30%)、磷石膏掺量(0、2%、4%、6%)对混凝土抗压强度的影响,优选出了最佳掺量,在此基础上,研究了磷石膏掺量(0、2%、4%、6%)对钢管混凝土轴压性能的影响。结果表明:当粉煤灰、矿粉、磷石膏的掺量分别为10%、20%、2%时,混凝土的28 d抗压强度最大;随着磷石膏掺量的增加,钢管混凝土试件的极限承载力先增大后减小,最佳掺量为2%,此时,钢管混凝土试件受压破坏后的横向变形不明显。

冻融循环下砂岩的动态劈裂特性与应变演变机理

为了研究冻融循环条件下砂岩的动态拉伸力学性能,利用分离式霍普金森压杆(SHPB)试验系统并结合高速数字图像相关技术(DIC),对冻融循环0次、10次、20次、40次的砂岩试件进行不同冲击速度下的动态劈裂试验,研究分析了不同冻融循环次数下冻结砂岩在动态拉伸应力下的强度特征、变形过程与破坏形态。结果表明:不同冻融循环作用下冻结砂岩与普通砂岩的动态拉伸曲线有着相似的应力发展特点,分为低速增长段、高速增长段、峰值平台段和降低段;冻岩的拉伸峰值应力与应力加载速率呈线性关系,与冻融循环次数之间呈现出先增大后减小的趋势;在相同打击强度下,4种冻融循环次数(N)的冻岩试件中心处拉伸应变大小依次为40次、20次、0次、10次,具有一定的冻融循环效应。