Determining the Onset and Strength of Unforced Wave Breaking in A Numerical Wave Tank

A numerical wave tank is used to investigate the onset and strength of unforced wave breaking, and the waves have three types of initial spectra： constant amplitude spectrum, constant steepness spectrum and Pierson-Moscowitz spectrum. Numerical tests are performed to validate the model results. Then, the onset of wave breaking is discussed with geometric, kinematic, and dynamic breaking criteria. The strength of wave breaking, which is always characterized by the fractional energy loss and breaking strength coefficient, is studied for different spectra. The results show how the energy growth rate is better than the initial wave steepness on estimating the fractional energy losses as well as breaking strength coefficient.

EFFECT OF FRICTIONAL FORCE ON GEARING CONTACT FATIGUE STRENGTH

The model for computing frictional coefficient between two teeth faces at the state of mixed elastohydrodynamic lubrication is established. And then more than 80 sets of numerical calculations and six sets of disc fatigue tests are completed. The results show that when the film thickness ratio λ 〈1.6, frictional coefficient μ is drastically decreased as λ. rises; Thereafter it decreases smoothly until λ=4.5. When λ〉4.5, however, it goes up again with λ, which indicates that the excessive film thickness ratio will deteriorate gearing contact fatigue strength. At the end, the formulae for determining the frictional coefficients are formed.

Influence of Carbon Content on Strain Hardening Behaviour of Sintered Plain Carbon Steel Preforms

Complete experimental investigation on the instantaneous strain hardening behaviour of powder metallurgy （P/M） preforms of pure iron, Fe 0.35%C, Fe-0.75%C and Fe-1.1%C was carried out. The strain hardening be haviour of the above-mentioned P/M sintered steel preforms with aspect ratio of 0.4 under triaxial stress state condition was determined by cold upsetting under nil/no and graphite lubricant conditions. The instantaneous strain hardening value （ni）, strength coefficient （Ki）, and the stress as a function of strain and densification were obtained and analyzed. Furthermore, a relation was obtained from a semi-log plot of stress against relative density and analyzed to study the hardening behaviour owing to densification as stress was a function of induced strain as well as densification in the P/M materials.

Analysis of the influencing factors of PAEs volatilization from typical plastic products

The primary emphasis of this research was to investigate the foundations of phthalate（PAEs） pollutant source researches and then firstly confirmed the concept of the coefficient of volatile strength, namely phthalate total content in per unit mass and unit surface area of pollutant sources. Through surveying and evaluating the coefficient of volatile strength of PAEs from typical plastic products, this research carried out reasonable classification of PAEs pollutant sources into three categories and then investigated the relationship amongst the coefficient of volatile strength as well as other environmental factors and the concentration level of total PAEs in indoor air measured in environment chambers.Research obtained phthalate concentration results under different temperature, humidity,the coefficient of volatile strength and the closed time through the chamber experiment. In addition, this study further explored the correlation and ratio of influencing factors that affect the concentration level of total PAEs in environment chambers, including environmental factors, the coefficient of volatile strengths of PAEs and contents of total PAEs in plastic products. The research created an improved database system of phthalate the coefficient of volatile strengths of each type of plastic goods, and tentatively revealed that the volatile patterns of PAEs from different typical plastic goods, finally confirmed that the coefficient of volatile strengths of PAEs is a major factor that affects the indoor air total PAEs concentration, which laid a solid foundation for further establishing the volatile equation of PAEs from plastic products.

Preparation of steel slag porous sound-absorbing material using coal powder as pore former

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5 MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50%（wt.%）, percentage of coal powder of 30%（wt.%）, sintering temperature of 1130°C,and sintering time of 6.0 hr, which were determined by analyzing the properties of the sound-absorbing material.