An Experimental Study of Composite Columns Filled with Eucalyptus nitens Timber under Axial Compression

Eucalyptus nitens(E.nitens)has been much used for producing paper but also shows promise for structural applications.In this study,static compressive tests were undertaken to examine its suitability to be used in an innovative composite column.The composite column was comprised of a rectangular steel tube with E.nitens timber infill.The nonlinear compressive behaviour of the composite column filled with E.nitens wood for both dry and wet conditions was examined.The same tests on rectangular steel tubes and bare dry and wet E.nitens samples were also undertaken as a comparison.For samples with different conditions,the ultimate capacity was evaluated and the effect of each condition on the compressive behaviour of the composite column was clarified.The steel tubes showed greater ductile behaviour,and more ductility was found in the wet samples.The steel tubes with E.nitens timber infill samples exhibited a greater linear elastic range connected with higher maximum loads,while the bare timber samples could support only lower maximum loads.The results from this research were promising for the use of rectangular steel tubes with E.nitens timber infill in structural applications.

Liquefaction mitigation in silty soils using composite stone columns and dynamic compaction

The objective of this study is to develop an analytical methodology to evaluate the effectiveness of vibro stone column (S.C.) and dynamic compaction (D.C.) techniques supplemented with wick drains to densify and mitigate liquefaction in saturated sands and non-plastic silty soils. It includes the following: (i) develop numerical models to simulate and analyze soil densitication during S.C. installation and D.C. process, and (ii) identify parameters controlling post-improvement soil density in both cases, and (iii) develop design guidelines for densification of silty soils using the above techniques. An analytical procedure was developed and used to simulate soil response during S.C. and D.C. installations, and the results were compared with available case history data. Important construction design parameters and soil properties that affect the effectiveness of these techniques, and construction design choices suitable for sands and non-plastic silty soils were identified. The methodology is expected to advance the use of S.C. and D.C. in silty soils reducing the reliance on expensive field trials as a design tool. The ultimate outcome of this research will be design charts and design guidelines for using composite stone columns and composite dynamic compaction techniques in liquefaction mitigation of saturated silty soils.

Behavior of slender steel concrete composite columns in eccentric loading

Ten slender steel reinforced cencrete （SRC） composite columns are tested under eccentric loading conditions. Effects of concrete strength, slenderness of columns and eccentricity of the axial load are studied. The load-carrying capacity is reduced with increased slenderness ratio and eccentricity. Concrete strength has no obvious influence on eccentrically loaded columns. Then, a nonlinear numerical method of pin-ended slender columns is also presented. This method is applicable for determining the material failure load or buckling failure load of a slender steel reinforced concrete composite column. In this method both material and geometric nonlinearities are taken into account. The results of numerical analysis accord well with the test results. The test results are also compared with the results predicted by ACI318-05 and the China Specifications.

Bearing capacity of composite columns reinforced by concrete filled steel tube

In this study, nine simplified short composite columns consisting of core CFST (concrete filled steel tube) of different diameters and outer reinforced concrete were constructed to study their compressive performance under axial or eccentric compression. The failure mode is characterized by the crush of the outer concrete. The bearing capacity increases at first and then decreases with further increase of the position coefficient. It can be concluded that position coefficient is an important structural parameter that has considerable influences on the ultimate bearing capacity of the composite columns. The outer concrete, steel tubes and longitudinal reinforcement are found to work in a cooperative manner under axial or eccentric compression when the position coefficient is about 0.5. An improved bearing capacity algorithm that takes the position coefficient into account has been proposed based on the experimental and simulation results and current technical specification in China. It has been proven to be precise and safe.

Analysis and seismic tests of composite shear walls with CFST columns and steel plate deep beams

A composite shear wall concept based on concrete filled steel tube （CFST） columns and steel plate （SP） deep beams is proposed and examined in this study. The new wall is composed of three different energy dissipation elements： CFST columns; SP deep beams; and reinforced concrete （RC） strips. The RC strips are intended to allow the core structural elements - the CFST columns and SP deep beams - to work as a single structure to consume energy. Six specimens of different configurations were tested under cyclic loading. The resulting data are analyzed herein. In addition, numerical simulations of the stress and damage processes for each specimen were carried out, and simulations were completed for a range of location and span-height ratio variations for the SP beams. The simulations show good agreement with the test results. The core structure exhibits a ductile yielding mechanism characteristic of strong column-weak beam structures, hysteretic curves are plump and the composite shear wall exhibits several seismic defense lines. The deformation of the shear wall specimens with encased CFST column and SP deep beam design appears to be closer to that of entire shear walls. Establishing optimal design parameters for the configuration of SP deep beams is pivotal to the best seismic behavior of the wall. The new composite shear wall is therefore suitable for use in the seismic design of building structures.

Comparison between Composite Column Using Limestone and Basalt Concrete

This research is conducted to study the experimental behavior of composite steel-concrete columns with basalt additives. Various percentages of basalt are added to the concrete mixes to investigate its effect on the total axial compressive capacity of the columns. Expected failure scenarios of the columns are: concrete compressive failure, buckling of steel section, and de-bonding between steel and concrete sections. A conventional limestone composite column was used as base mix. The results of the study indicate a significant improvement in structural behavior and strength of the columns by increasing the percentage of basalt content.

Mechanical Behavior of Rectangular Steel-Reinforced ECC/Concrete Composite Column under Eccentric Compression

In order to improve the seismic performance, deformation ability and ultimate load-carrying capacity of columns with rectangular cross section, engineered cementitious composite(ECC) is introduced to partially substitute concrete in the edge zone of reinforced concrete columns and form reinforced ECC/concrete composite columns.Firstly, based on the assumption of plane remaining plane and the simplified constitutive models, the calculation method of the load-carrying capacity of reinforced ECC/concrete columns is proposed. The stress and strain distributions and crack propagation of the composite columns in different states of eccentric compressive loading are analyzed. Then, nonlinear finite element analysis is conducted to study the mechanical performance of reinforced ECC/concrete composite columns with rectangular cross section. It is found that the simulation results are in good agreement with the theoretical results, indicating that the proposed method for calculating the load-carrying capacity of concrete/ECC composite columns is valid. Finally, based on the proposed method, the effects of ECC thickness, compressive strength of concrete and longitudinal reinforcement ratio on the mechanical performance of reinforced ECC/ concrete composite columns are analyzed. Calculation results indicate that increasing the thickness of ECC layer or longitudinal reinforcement ratio can effectively increase the ultimate load-carrying capacity of the composite column with both small and large eccentricity, but increasing the strength of concrete can only increase the ultimate loadcarrying capacity of the composite column with small eccentricity.

Numerical Modeling on Seismic Performance of Castellated Composite Beam⁃Reinforced Concrete Column Connection

The hybrid structure consisting of castellated composite beam and compound spiral hoop reinforced concrete column take full advantages of steel and concrete material.To popularize the structural form in real conditions,a beam⁃through⁃type beam⁃column connection is proposed.Two 1/2⁃scaled connection specimens were tested and three⁃dimensional finite element models of the beam⁃column connection were set up.The longitudinal reinforcements,concrete beam,and column were simulated by link and solid elements,respectively.The influences of the parameters such as expansion ratio,location of web opening,and original height of steel beam were studied.The results show that connections possessed high initial rigidity.The expansion ratio of steel beam showed more important influence on the connection’s ultimate bearing capacity.For the connection models with steel beam expansion ratio of 1.4,the maximum increment of the ultimate bearing capacity of the connection could reach 28%.In order to prevent the local buckling failure of steel beam from occurring near web opening,the expansion ratio of steel beam should not be greater than 1.3.

Seismic Behavior of Confined RC ColumnComposite Beam Joints

In order to evaluate the seismic behavior of confined RC column-composite beam joints, five interior joints were tested under low cyclic reversed load. The weakening extent of flanges, the number of studs, and whether to reinforce weakened flanges were used as parameters in designing these five joints. Failure characteristics, hysteretic curves, skeleton curves, ductility, energy dissipation, strength degradation, and stiffness degradation were analyzed. The test results revealed that the steel beam flanges in the joints were equivalent to the tie rod. Weakened flanges resulted in poor seismic behavior; however, the seismic behavior could be improved by increasing studs and reinforcing weakened flanges. The joint steel plate hoops, equivalent to stirrups, did not yield when the maximum load was reached, but yielded when the failure load was reached for the joints with shear failure. Increasing stud-type joints and reinforcing flange-type joints ensured good seismic behavior and met project requirements. Based on the experimental results, the failure mechanism of the joints was discussed, and the shear capacity equations of the joints was presented.

Static behavior of semi-rigid thin-walled steel-concrete composite beam-to-column joints with bolted partial-depth flush end plate:experimental study

A new type of semi-rigid thin-walled steel-concrete composite beam-to-column joint has been proposed in this paper.Five semi-rigid composite beam-to-column joint specimens subjected to hogging moments under monotonic loading were tested to study the static behavior of this new type of joint.The main variable parameters for the five joint specimens were the longitudinal reinforcement ratio and the joint type.The experimental results designated that the magnitude of extension of the longitudinal reinforcement is the most important factor that influenced the moment-rotation characteristic of the new type of joint.The concrete slabs could resist 3.8%-19.1% of the total shear load applied to the cross-sections near the beam-to-column connection.The edge stiffened elements,such as the flange of the lipped I-section thin-walled steel beam,were capable of having considerable inelastic deformation capacity although they had comparatively large width-to-thickness ratios.The shear failure of the concrete cantilever edge strip must be taken into account in practical design because it has significant influence on the anchorage of the longitudinal reinforcement in the new type of external joints.

Testing of a Full-Scale Composite Floor Plate

A full-scale composite floor plate was tested to investigate the flexural behavior and in-plane effects of the floor slab in a grillage of composite beams that reduces the tendency for longitudinal splitting of the concrete slab along the line of the primary beams. This is important in cases where the steel decking is discontinuous when it is orientated parallel to the beams. In this case, it is important to demonstrate that the amount of transverse reinforcement required to transfer local forces from the shear connectors can be reduced relative to the requirements of Eurocode 4. The mechanism under study involved in-plane compression forces being developed in the slab due to the restraining action of the floor plate, which was held in position by the peripheral composite beams;while the secondary beams acted as transverse ties to resist the forces in the floor plate that would otherwise lead to splitting of the slab along the line of the primary beams. The tendency for cracking along the center line of the primary beam and at the peripheral beams was closely monitored. This is the first large floor plate test that has been carried out under laboratory conditions since the Cardington tests in the early 1990s, although those tests were not carried out to failure. This floor plate test was designed so that the longitudinal force transferred by the primary beams was relatively high (i.e., it was designed for full shear connection), but the transverse reinforcement was taken as the minimum of 0.2% of the concrete area. The test confirmed that the primary beams reached their plastic bending resistance despite the discontinuous decking and transverse reinforcement at the minimum percentage given in Eurocode 4. Based on this test, a reduction factor due to shear connectors at edge beams without U-bars is proposed.

Composition control and temperature inferential control of dividing wall column based on model predictive control and PI strategies

The dividing wall column(DWC) is considered as a major breakthrough in distillation technology and has good prospect of industrialization. Model predictive control(MPC) is an advanced control strategy that has acquired extensive applications in various industries. In this study, MPC is applied to the process for separating ethanol,n-propanol, and n-butanol ternary mixture in a fully thermally coupled DWC. Both composition control and temperature inferential control are considered. The multiobjective genetic algorithm function "gamultiobj" in Matlab is used for the weight tuning of MPC. Comparisons are made between the control performances of MPC and PI strategies. Simulation results show that although both MPC and PI schemes can stabilize the DWC in case of feed disturbances, MPC generally behaves better than the PI strategy for both composition control and temperature inferential control, resulting in a more stable and superior performance with lower values of integral of squared error(ISE).

Experimental Behavior of Recycled Aggregate Concrete Filled Steel Tubular Columns

During the modernization or rehabilitation activity,the demolished structural waste causes large soil pollution and unavailability of natural aggregate is the big concern for the construction industry.Therefore,this manuscript deals with the Composite Steel Circular Column(CSCC)with Recycled Aggregate concrete(RAC)as infill is partly used,with the replacement of 25%and 50%in M30 grade of Concrete.And internal reinforcement steel is fully replaced by rolled steel tubes(circular and square)with varied thickness,ISA-unequal angle.Around 14 specimens are cast and examined under axial load for analysis of the deflection characteristics,the load-bearing capacity along with its buckling behavior.The experimental values are estimated through LVDT(linear variable differential transducer)at 3-phase.The curve of load-deflection is drawn with the load pattern.From the date interpretation,it is found column made of 50%-RAC has more than 25%-RAC.

部分包覆钢-混凝土组合梁柱节点抗震性能试验研究

为研究不同连接构造的部分包覆钢-混凝土组合梁柱节点(PEC梁柱节点)的抗震性能,对2个PEC梁柱节点试件进行了拟静力加载试验,研究了低周往复荷载作用下PEC梁柱节点试件的破坏现象、滞回曲线、骨架曲线、延性、耗能能力和刚度退化等抗震性能。结果表明:强轴连接PEC梁柱节点的滞回曲线呈梭形和弓形,在达到极限承载力后仍能保持一定的延性和耗能能力;弱轴连接PEC梁柱节点牛腿与梁间的焊缝处发生破坏,未展现出预期的耗能能力,PEC梁仍在弹塑性状态,没有达到极限状态;PEC梁柱节点核心区混凝土替换为加劲肋板后,试件仍具有较好的承载力、延性和耗能能力,刚度退化规律无明显变化,且强轴连接节点与弱轴连接节点刚度变化规律基本一致;PEC柱牛腿设计过短会导致焊缝连接处断裂,试件延性和耗能能力得不到发挥,剩余刚度较大。

3D打印混凝土永久模板叠合柱的抗压性能数值模拟研究

为深入研究3D打印混凝土永久模板叠合柱的抗压性能,基于3D打印混凝土永久模板叠合柱及同尺寸整体现浇对照柱试验建立构件数值模型,模拟分析其轴压荷载-位移响应及失效形态。针对界面粘结性能、现浇混凝土抗压强度、打印模板厚度、荷载偏心距等参数开展3D打印混凝土永久模板叠合柱的抗压性能计算分析,研究表明:叠合柱轴压极限承载力随着薄弱界面剪切强度、刚度及现浇混凝土抗压强度的增大而增大。由于打印材料的抗压强度高于现浇混凝土,叠合柱抗压极限承载力提升率与打印模板厚度呈近似线性关系,叠合圆柱的抗压极限承载力随着荷载偏心距的增大而降低,呈近似线性负相关。此外,偏心距对叠合圆柱极限承载力下降幅度的影响大于现浇圆柱。

碎石桩复合地基非等应变非线性固结特性分析

现有碎石桩复合地基固结理论通常基于等应变假设,与工程实际情况有出入。基于分段线性差分法,建立了一种考虑非等应变刺入修正和任意桩土非线性本构关系的碎石桩复合地基非线性固结模型。该模型可以考虑桩土自重、涂抹区、井阻效应和变荷载,可以计算碎石桩向垫层或下卧层的刺入并对等应变假设进行修正,可以分析桩土附加应力沿深度方向的衰减,以及任意的非线性压缩性及渗透性关系。与工程实测数据对比发现,考虑非等应变修正的模型计算值与工程实测值基本吻合。结合算例分析,进一步研究了垫层及下卧层模量、桩土竖向应力衰减和应力路径对碎石桩复合地基土体固结特性的影响,结果表明:碎石桩向垫层或下卧层刺入使复合地基桩土应力比减小、沉降量增大、固结速率减缓;忽略桩土竖向应力衰减虽对固结速率影响不大,但会高估复合地基沉降变形;不同应力路径对碎石桩复合地基固结特性影响显著,简化的土层压缩性关系将对分析结果带来较大误差。

钢筋混凝土梁柱边节点滞回性能数值模拟

为准确模拟梁柱边节点在地震条件作用下的滞回响应,建立考虑黏结退化机制的梁柱边节点有限元模型。基于ANSYS有限元平台,采用Voce-Chaboche混合强化模型定义钢筋的循环本构关系,开发组合弹簧单元实现往复荷载作用下钢筋与混凝土间的黏结退化机制,根据损伤理论提出往复荷载作用下黏结滑移本构关系预测模型。有限元计算得到的滞回曲线、骨架曲线、刚度退化曲线、应力云图与试验结果的对比表明:混合强化本构能更好地描述往复荷载作用下钢筋的滞回响应,组合弹簧单元成功地反演了往复荷载作用下钢筋与混凝土的黏结退化特征,往复荷载作用下节点梁中塑性铰的发育导致梁塑性伸长,将对边节点柱造成不利影响,梁柱边节点数值模拟结果与试验结果吻合良好,为准确模拟梁柱边节点的滞回性能提供了理论基础和技术平台。

配筋PVA-钢混杂纤维增强水泥基复合材料梁柱边节点抗震性能试验研究

改善工程材料韧性和耐久性,提高框架梁柱节点抵抗变形和破坏的能力,是提高框架结构抗震韧性的有效途径之一。采用PVA-钢混杂纤维增强水泥基复合材料代替普通混凝土应用到梁柱边节点,考虑轴压比和加密区体积配箍率的影响,设计6个配筋PVA-钢混杂纤维增强水泥基复合材料、1个配筋单掺PVA纤维增强水泥基复合材料和1个钢筋混凝土梁柱边节点试件进行拟静力试验,分析其破坏形态、滞回曲线、骨架曲线、延性、耗能能力、钢筋应变和梁端塑性铰区转角,探讨混杂纤维的加入对梁柱边节点抗震性能的影响。结果表明:与钢筋混凝土节点和单掺PVA纤维增强水泥基复合材料节点相比,PVA-钢混杂纤维增强水泥基复合材料节点的承载力高、变形能力大、延性好、耗能能力强,抗震性能显著提升。当试验轴压比从0.12增加到0.24,梁端塑性铰区产生一定的外移,塑性性能发挥更充分,同时试件的变形能力、延性、耗能能力增加。在加密区体积配箍率减小的情况下,试件仍表现出良好的抗震性能。