Geostress measurements near fault areas using borehole stress-relief method

To minimize negative effects of geostress distribution on mining safety near the fault areas, the UPM40 triaxial geostress testing system was introduced to conduct in-situ geostress measurements at three sites and nine points by the borehole stress-relief method. The results of strain?confining pressure curves show that rock masses at the three measuring sites exhibit comprehensive linear elasticity in spite of various fissures or cracks within rocks. Horizontal and vertical stress components distribute discrepantly near the fault areas, and the maximum lateral pressure coefficient is as high as 6.15. The maximum principle stress ranges from 8.01 to 14.93 MPa, and stress directions are in the range of N78.07°W?N17.55°W. Geostresses near fault areas are dominated by the horizontal tectonic stresses, while the lower values, compared to those under similar geological conditions are due to stress release by the fault. Additionally, the fault and shear stress nearby are partially responsible for asymmetric elongation and southwesterly migration of orebodies.

Non-complete relief method for measuring surface stresses in surrounding rocks

The measurement of surface stresses in surrounding rocks with the use of a relief method of annular hole-drilling was studied by numerical analysis. The stress relief process by hole-drilling was then simulated with the use of finite element method. The influences of the borehole diameter(d), the initial stresses and the ratio of the initial principle stresses on the variations of the remained stress and the released stress in function of the relief depth(h) were discussed. The relation between the non-dimensional ratio of the released principle strains and that of the initial principle stresses, and the effect of the elastic modulus and the Poisson ratio of the rock mass on the stress relief curves were studied. The results show that the stress relief behavior formulated with the non-dimensional ratio of the released stress and the ratio of h/d is only sensitive to the ratio of the initial principle stresses and the Poisson ratio. The stresses are completely released when h equals 1.6d, and the tensile stresses take place on the bore core surface in the relief measurement process. Finally, a non-complete relief method of annular hole-drilling for measuring surface stress in surrounding rocks is proposed and the procedure is presented.

TECHNOLOGY OF QUANTITATIVE ANALYSIS ON VIBRATORY STRESS RELIEF BASED ON ULTRASONIC TIME-OF-ARRIVAL METHOD

The effect of vibratory stress relief （VSR） is usually evaluated with the indirect method of observing the change of amplitude frequency response characteristics of structures. A new kind of evaluating method of VSR based on the ultrasonic time-of-arrival method （UTM）, which can obtain the residual stress directly through measuring the propagation time of ultrasonic wave in the material, is presented. At first, the principle of the measuring method of residual stress based on UTM is analyzed. Then the measuring system of the method is described, which is in virtue of ultrasonic flaw detector and high-sampling-rate digital oscillograph. And a set of calibration system that contains a piece of standard specimen is also introduced. Experimental results prove the relation between the residual stress and the propagation time of ultrasonic in workpieces. Finally, the measuring and calibration systems are applied in evaluating the effect of VSR. The final test results show that the method is effective.

Stress relief and crystal face transition process contribute to the stability of zinc anodes

Zn electrodes are suffering the dendrite growth owing to the enrichment of local space charge, distinct exposed face and residual stress. In this work, we investigated the crystal face properties and stress state of Zn foil through static energy calculations, dynamic crystal growth analysis and finite element simulation of stress states. Then thermal driven is deployed to modify the exposure face and residual stress of Zn foil, aiming for a dendrite-free electrode. The calculation of surface energies and simulation of crystal growth models for different crystal faces indicate that the(0 0 1) face can maintain stability during deposition. Inspired by this mechanism, the(1 0 1) exposed commercial Zn foil is modified by thermal processing. Firstly, the exposure level of the(0 0 1) face increases, though only the peak corresponding to the(0 0 2) crystal face is observed, due to the extinction effect of the densely packed plane(0 0 1) face.Further, the surface morphology becomes smooth and the stress is released with the progresses time.These stress relief and crystal face transition process strengthen the uniformity of ion distribution, and increase the interface stability during the crystal growth, which reduce the defect sites in the deposition.As a result, the Zn electrode exhibits tiny voltage hysteresis and outstanding cycle stability, which reveals improved electrochemical performance. Additionally, Li and Na can also be improved in exposed crystal faces and release strain energy through similar methods to enhance cycling stability.

Support design method for deep soft-rock tunnels in non-hydrostatic high in-situ stress field

Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunnels will suffer serious asymmetric deformation.There is no available support design method for tunnels under such a situation in existing studies to clarify the support time and support stiffness.This study first analyzed the mechanical behavior of tunnels in non-hydrostatic in-situ stress field and derived the theoretical equations of the ground squeezing curve(GSC)and ground loosening curve(GLC).Then,based on the convergence confinement theory,the support design method of deep soft-rock tunnels under non-hydrostatic high in-situ stress field was established considering both squeezing and loosening pressures.In addition,this method can provide the clear support time and support stiffness of the second layer of initial support.The proposed design method was applied to the Wanhe tunnel of the China-Laos railway in China.Monitoring data indicated that the optimal support scheme had a good effect on controlling the tunnel deformation in non-hydrostatic high in-situ stress field.Field applications showed that the secondary lining could be constructed properly.

Novel damage constitutive models and new quantitative identification method for stress thresholds of rocks under uniaxial compression

Four key stress thresholds exist in the compression process of rocks,i.e.,crack closure stress(σ_(cc)),crack initiation stress(σ_(ci)),crack damage stress(σ_(cd))and compressive strength(σ_(c)).The quantitative identifications of the first three stress thresholds are of great significance for characterizing the microcrack growth and damage evolution of rocks under compression.In this paper,a new method based on damage constitutive model is proposed to quantitatively measure the stress thresholds of rocks.Firstly,two different damage constitutive models were constructed based on acoustic emission(AE)counts and Weibull distribution function considering the compaction stages of the rock and the bearing capacity of the damage element.Then,the accumulative AE counts method(ACLM),AE count rate method(CRM)and constitutive model method(CMM)were introduced to determine the stress thresholds of rocks.Finally,the stress thresholds of 9 different rocks were identified by ACLM,CRM,and CMM.The results show that the theoretical stress−strain curves obtained from the two damage constitutive models are in good agreement with that of the experimental data,and the differences between the two damage constitutive models mainly come from the evolutionary differences of the damage variables.The results of the stress thresholds identified by the CMM are in good agreement with those identified by the AE methods,i.e.,ACLM and CRM.Therefore,the proposed CMM can be used to determine the stress thresholds of rocks.

Evaluation of residual stress relief of aluminum alloy 7050 by using crack compliance method

High strength aluminum alloys of 7xxx series have unacceptable levels of quenching residual stresses from solution heat treatment. The residual stress not only results in machining distortion and dimensional instability, but also increases the possibility of stress corrosion cracks. Therefore, it is necessary to reduce the residual stress to an acceptable level. The crack compliance method was adopted to study the influences of various stress relief methods on residual stress patterns in 7050 aluminum alloy. The results show that 90% residual stress can be eliminated by the cold stretching(Tx51) method. And a lower level of residual stress can be achieved by the uphill quenching(Tx53) method or the cold compression(Tx52). However, there is a very steep residual stress gradient normal to exterior surfaces.

Stress Relief Measurements in Young Adults and Adolescents—A Comparative Pilot Study with Different Relaxation Programs

Background: Chronic stress is a emotional challenge. Constant pressure presents a serious risk of damage to mental and physical health and hence is associated with increased incidence of various diseases. The ability to cope with chronic stress may be a function of psychological resilience including intellectual capacities, but more so of external factors such as life experience and education. Adolescents are more vulnerable to chronic stress than adults. The measures introduced during the COVID-19 pandemic brought up major societal problems. As both children and adolescents lost their life anchors, the prevalence of stress in adolescents increased from 20% to 45%. Chronic psychological stress can impede the normal development of schoolchildren. It may cause anxiety, social withdrawal, interpersonal conflicts and aggression. This applies particularly to those in puberty, with the adolescent already facing unstable social bonds and elevated fear about the future. It is likely that the puberty cohort accounts for the dramatic increase in the prevalence of stress. Since it impacts public health, chronic stress among school-age children is increasingly taking on a socio-political dimension. Non-clinical stress intervention studies can investigate how to achieve stress reduction in school children. Methods: In a small pilot study, we analysed the effects of a training program with four different standard interventions, i.e. mindfulness training, progressive muscle reflection, autogenic training, and sound meditation. We obtained baseline scores of 10 stress-indicators, and re-tested after the interventions were performed. Results: The four applied interventions resulted in a reduction of 8 (out of 10) stress-indicators, such as “feeling stressed” or stress related symptoms (headaches, dizziness, sweating). This positive impact of the interventions significantly reduced “Fears about the future” (p Discussion: School children recognise the positive potential of stress reducing training or interventions. Our results provide evidence in support of integrating the training of relaxation techniques in the school curriculum. We propose that a larger study be undertaken to determine which methods would be most effective.

Thermal Stresses and Cracks During the Growth of Large-sized Sapphire with SAPMAC Method

The finite-element method has been used to study the thermal stress distribution in large-sized sapphire crystals grown with the sapphire growth technique with micro-pulling and shoulder-expanding at cooled center （SAPMAC） method. A critical defect model has been established to explain the growth and propagation of cracks during the sapphire growing process. It is demonstrated that the stress field depends on the growth rate, the ambient temperature and the crystallizing direction. High stresses always exist near the growth interfaces, at the shoulder-expanding locations, the tailing locations and the sites where the diameters undergo sharp changes. The maximum stresses always occur at the interface of seeds and crystals. Cracks often form in the critical defect region and spread in the m-planes and a-planes under applied tensile stresses during crystal growth. The experimental results have verified that with the improved system of crystal growth and well-controlled techniques, the large-sized sapphire crystals of high quality can be grown due to absence of cracks.

Internal residual stress measurement on linear friction welding of titanium alloy plates with contour method

The internal residual stress within a TC 17 titanium alloy joint welded by linear friction welding （LFW） was measured by the contour method, which is a relatively new and destructive technique to obtain a full map of internal residual stress. The specimen was first cut into two parts; the out-of-plane displacement contour formed by the release of the residual stress was then measured; finally, taking the measured contour of the cut plane as the boundary conditions, a linear elastic finite element analysis was carried out to calculate the corresponding distribution of residual stress normal to the cut plane. The internal stress distribution of the TC 17 titanium alloy LFWjoint was also analyzed. The results show that the tensile residual stress in the TC17 LFW weld is mainly present within a region about 12 mm from the weld centerline; the peak tensile residual stress occurs at the weld centerline and reaches 360 MPa （about one third of the yield strength of TC17 alloy）; within the weld zone of the TC17 LFW weld, the through-thickness stress is not uniform, and the internal stress is larger than that near the top or bottom surface.

Research Progress and Identification Method of Apple Stress Resistance

In the research, changes of apple chemistry, and molecule, under stresses, are n terms of morphology, physiology, bio- illustrated and research and identifica- tion methods of apple resistance are explored involving drought-resistance, flood-re- sistance, salt-stress resistance, cold-hardiness and heat-resistance. In addition prospects of apple resistance research are proposed, as well.

METHOD TO CALCULATE BENDING CENTER AND STRESS INTENSITY FACTORS OF CRACKED CYLINDER UNDER SAINT_VENANT BENDING

Using the single crack solution and the regular solution of plane harmonic function, the problem of Saint_Venant bending of a cracked cylinder by a transverse force was reduced to solving two sets of integral equations and its general solution was then obtained. Based on the obtained solution, a method to calculate the bending center and the stress intensity factors of the cracked cylinger whose cross_section is not thin_walled, but of small torsion rigidity is proposed. Some numerical examples are given.

SIMULATION OF VIBRATION STRESS RELIEF AFTER WELDING BASED ON FEM

A finite element model is developed for the simulation of vibration stress relief （VSR） after welding. For the nonresonant vibration, the reduction in stress strongly depends on the amplitude of vibration. For the resonant vibration, the vibration frequency is the key for stress relief. The vibration frequency should be close to the structure natural frequency for the desired vibration mode. Only small vibration amplitude is required, which will be amplified during vibration. Vibration time does not have a major impact on vibration stress relief. When the amplitude of vibration stress relief is large, the treatment will be more effective.

Analysis of the Wenchuan Ms8.0 Earthquake's Co-seismic Stress and Displacement Change by Using the Finite Element Method

The variation of in situ stress before and after earthquakes is an issue studied by geologists. In this paper, on the basis of the fault slip dislocation model of Wenchuan Ms8.0 earthquake, the changes of co-seismic displacement and the distribution functions of stress tensor around the Longmen Shan fault zone are calculated. The results show that the co-seismic maximum surface displacement is 4.9 m in the horizontal direction and 6.5 m in the vertical direction, which is almost consistent with the on-site survey and GPS observations. The co-seismic maximum horizontal stress in the hanging wall and footwall decreased sharply as the distance from the Longmen Shan fault zone increased. However, the vertical stress and minimum horizontal stress increased in the footwall and in some areas of the hanging wall. The study of the co-seismic displacement and stress was mainly focused on the long and narrow region along the Longmen Shan fault zone, which coincides with the distribution of the earthquake aftershocks. Therefore, the co-seismic stress only affects the aftershocks, and does not affect distant faults and seismic activities. The results are almost consistent with in situ stress measurements at the two sites before and after Wenchuan Ms8.0 earthquake. Along the fault plane, the co-seismic shear stress in the dip direction is larger than that in the strike direction, which indicates that the faulting mechanism of the Longmen Shan fault zone is a dominant thrust with minor strike-slipping. The results can be used as a reference value for future studies of earthquake mechanisms.

Stress initialization methods for dynamic numerical simulation of rock mass with high in-situ stress

In the context of deep rock engineering,the in-situ stress state is of major importance as it plays an important role in rock dynamic response behavior.Thus,stress initialization becomes crucial and is the first step for the dynamic response simulation of rock mass in a high in-situ stress field.In this paper,stress initialization methods,including their principles and operating procedures for reproducing steady in-situ stress state in LS-DYNA,are first introduced.Then the most popular four methods,i.e.,explicit dynamic relaxation(DR)method,implicit-explicit sequence method,Dynain file method and quasi-static method,are exemplified through a case analysis by using the RHT and plastic hardening rock material models to simulate rock blasting under in-situ stress condition.Based on the simulations,it is concluded that the stress initialization results obtained by implicit-explicit sequence method and dynain file method are closely related to the rock material model,and the explicit DR method has an obvious advantage in solution time when compared to other methods.Besides that,it is recommended to adopt two separate analyses for the whole numerical simulation of rock mass under the combined action of in-situ stress and dynamic disturbance.

Method for Measuring Residual Stresses Induced by Boring in Internal Surface of Tube and Its Validation with XRD Method

Residual stresses can have a strong effect on the usability of machined parts,and the X-ray diffraction(XRD)measuring equipment,which is commonly used to measure residual stresses,is very expensive.This paper presents a method of measuring the residual stresses induced by boring in the internal surface of a tube with much cheaper equipment.The method,called the strain-based method is mainly based on the strains measured on the external surface of the tube.It is proposed on the basis of the very long tube assumption.The finite element method(FEM)analysis is thus used to validate the length of the tube.Guided by the FEM results,an appropriate length of the tube is chosen,and the residual stresses are obtained from both the strain-based method and the XRD method.Stress profiles obtained from both two methods are compared.The comparison result indicates that the profiles of the two methods agree well with each other.Therefore,it can be concluded that the accuracy of the strain-based method is high enough,and it can be applied to residual stress measurement in practice.

An extended displacement discontinuity method for analysis of stress wave propagation in viscoelastic rock mass

An extended displacement discontinuity method (EDDM) is proposed to analyze the stress wave propagation in jointed viscoelastic rock mass (VRM).The discontinuities in a rock mass are divided into two groups.The primary group with an average geometrical size larger than or in the same order of magnitude of wavelength of a concerned stress wave is defined as 'macro-joints',while the secondary group with a high density and relatively small geometrical size compared to the wavelength is known as 'micro-defects'.The rock mass with micro-defects is modeled as an equivalent viscoelastic medium while the macro-joints in the rock mass are modeled explicitly as physical discontinuities.Viscoelastic properties of a micro-defected sedimentary rock are obtained by longitudinally impacting a cored long sedimentary rod with a pendulum.Wave propagation coefficient and dynamic viscoelastic modulus are measured.The EDDM is then successfully employed to analyze the wave propagation across macro-joint in VRM.The effect of the rock viscosity on the stress wave propagation is evaluated by comparing the results of VRM from the presented EDDM with those of an elastic rock mass (ERM) from the conventional displacement discontinuity method (CDDM).The CDDM is a special case of the EDDM under the condition that the rock viscosity is ignored.Comparison of the reflected and transmitted waves shows that the essential rock viscosity has a significant effect on stress wave attenuation.When a short propagation distance of a stress wave is considered,the results obtained from the CDDM approximate to the EDDM solutions,however,when the propagation distance is sufficiently long relative to the wavelength,the effect of rock viscosity on the stress wave propagation cannot be ignored.

STRESS FIELD ANALYSIS OF EXTRA-HEIGHT FORGING DIE USING FINITE ELEMENT METHOD

ＴｈｅｅｘｔｒａｈｅｉｇｈｔｆｏｒｇｉｎｇｄｉｅｉｎＳｏｕｔｈｅｗｅｓｔＡｌｕｍｉｎｉｕｍＦａｂｒｉｃａｔｉｏｎＰｌａｎｔｉｓａｓｐｅｃｉａｌｄｉｅｆｏｒｍａｋｉｎｇａｒｍａｍｅｎｔａｎｄｓｐｅｃｉａｌｃｉｖｉｌｐｒｏｄｕｃｔｓｉｎＣｈｉｎａ．Ａ...

METHOD TO CALCULATE STRESS INTENSITY FACTOR OF V-NOTCH IN BI-MATERIALS

Based on Zak＇s stress function, the eigen-equation of stress singularity ofbi-materials with a V-notch was obtained. A new definition of stress intensity factor for a perpendicular interfacial V-notch of bi-material was put forward. The effects of shear modulus and Poisson＇s ratio of the matrix material and attaching material on eigen-values were analyzed. A generalized expression for calculating/（i of the perpendicular V-notch of bi-materials was obtained by means of stress extrapolation. Effects of notch depth, notch angle and Poisson＇s ratio of materials on the singular stress field near the tip of the V-notch were analyzed systematically with numerical simulations. As an example, a finite plate with double edge notches under uniaxial uniform tension was calculated by the method presented and the influence of the notch angle and Poisson＇s ratio on the stress singularity near the tip of notch was obtained.

Measuring internal residual stress in Al-Cu alloy forgings by crack compliance method with optimized parameters

Measuring the internal stress of Al alloy forgings accurately is critical for controlling the deformation during the subsequent machine process.In this work,the crack compliance method was used to calculate the internal residual stress of Al-Cu high strength alloys,and the effect of various model parameters of crack compliance method on the calculated precision was studied by combining the numerical simulation and experimental method.The results show that the precision first increased and then decreased with increasing the crack range.The decreased precision when using a high crack range was due to the strain fluctuation during the machining process,and the optimized crack range was 71%of the thickness of forgings.Low orders of Legendre polynomial can result in residual stress curve more smooth,while high orders led to the occurrence of distortion.The Tikhonov regularization method effectively suppressed the distortion of residual stress caused by the fluctuation of strain data,which significantly improved the precision.In addition,The crack compliance method with optimized parameters was used to measure the residual stress of Al-Cu alloy with different quenching methods.The calculated results demonstrated that the distribution of residual stress was obtained accurately.