Experimental study on the gas-stripping chamber of an E//B neutral particle analyzer

Stripping units take a key role in the neutral particle analyzer(NPA).A renovated gas-stripping unit was constructed for the newly designed E//B NPA.Using H_(2)as the working gas,we measured the gas inlet pressure(P_(0))and vacuum chamber pressure(P_(3)).The pressure distribution inside the gas-stripping room was calculated with Ansys Fluent,using the measured P_(0)and P_(3)as boundary conditions.The stripping efficiency of the stripping unit was then simulated utilizing the Geant4 Monte Carlo code for the H and D particles.The pressure P_(0)=40 Pa,which is one-sixth of what found in the previous design and corresponds to a thickness of 1.27×10^(17)atoms∕cm^(2),was obtained as the optimum working pressure for the upgraded stripping unit.An 50 kV electron cyclotron resonance(ECR)ion source platform was designed and constructed for E//B NPA calibration,and its performance has been measured.Using the ECR ion source platform,we measured the efficiency of the stripping unit through an inverse experiment with proton beams.We compared the current ratios of measurements with and without H_(2)gas to Geant4 simulation results.We found adequate agreement between the overall trends of the experiment and the simulation.The significant deviation for incident energies below 20 keV may result from the scattering effects of low-energy protons,leading to reduced accuracy in single-scattering physics in Geant4 simulations.Applying the scattering corrections observed in the reverse experiments obtains more accurate stripping efficiencies for H and D atoms in the energy range of 20–200 keV and the global efficiency with the maximum values of 95.0%for H atoms and 78.9%for D atoms at 200 keV.

Molecular investigation into the transformation of recalcitrant dissolved organic sulfur in refinery sour water during stripping process

Refinery sour water primarily originates from the tops of towers in various units and coker condensate,and cannot be discharged directly to a wastewater treatment plant due to high levels of chemical oxygen demand(COD)and organic sulfur contents.Even after the recovery of H_(2)S from the sour water by the stripping process,the effluent still contains a high concentration of dissolved organic sulfur(DOS),which can have a huge bad influence.While chemical composition of dissolved organic matter(DOM)in refinery wastewater has been extensively studied,the investigation of recalcitrant DOS from sour waters remains unclear.In the present study,chemical composition of sour water DOMs(especially DOS)was investigated using fluorescence spectroscopy(excitation-emission matrix,EEM)and mass spectrometry,including gas chromatography-mass spectrometry(GC-MS)and high-resolution Orbitrap MS.The GC-MS and EEM results showed that volatile and low-aromaticity compounds were effectively removed during the stripping process,while compounds with high hydrophilicity and humification degree were found to be more recalcitrant.The Orbitrap MS results showed that weak-polar oxygenated sulfur compounds were easier to be removed than oxygenated compounds.However,the effluent still contained significant amounts of sulfur-containing compounds with multiple sulfur atoms,particularly in the form of highly unsaturated and aromatic compounds.The Orbitrap MS/MS results of CHOS-containing compounds from the effluent indicate that the sulfur atoms may exist as sulfonates,disulfide bonds,thioethers.Understanding the composition and structure of sour water DOS is crucial for the development of effective treatment processes that can target polysulfide compounds and minimize their impact on the environment.

径向对称电导率重构的Layer-Stripping方法

利用Layer-Stripping方法,针对电导率为径向对称分布的情形给出一种重构电导率的数值算法.特别地,针对分层半径的选取提出了3种方法以增强算法的稳定性,并通过数值实验证明了算法的可行性.

Removing ammonia from skim by air stripping with rotating packed bed

Based on the effects of skim components on ammonium removal as well as the current processing technology, a new process-intensified technology of removing ammonia from skim by air stripping on rotating packed bed was proposed. The experiments were conducted on a wave-thread packed Rotating Packed Bed(RPB) under atmospheric pressure, suggesting that, in terms of order of importance, the ammonium concentration of feed-stock(x_w), the average ultra-gravity factor(β), feed-stock flux(L), and gas flux(G) had significant impact on ammonium removal rate(η) and the ammonium concentration of products(x_D). In the experiment, mass-transfer coefficient in gas phase(k_ya_e) increases with the increase of β, G/L, and L. The ammonium concentration of products decreases with the increase of β, G/L and the increase of L. The ammonium concentration of products would be as low as ~0.10% and the ammonia removal rate would be 63.21% when skim temperature was 25 °C, x_w0.28%, β 133.2, and G/L 15.0 m^3·L^(-1). Experiment results indicated that the proposed technology for removing ammonium from skim on a rotating packed bed would be a new process-intensified technique compared with traditional aeration process and centrifugal atomization method.

Study on Semi-Continuous Technology System for Soft Material Stripping in Large Surface Mines

Continuous and semi-continuous mining technology has become the main trend of modern surface mines in the world. According to the deposit characteristics of coal basin in China and Chinese situation,this paper discussed the new semi-continuous technology── shovel - transfer wagon-belt conveyor and its application prospect in large surface coal mines in China.

Effect of Packing Materials and Other Parameters on the Air Stripping Process for the Removal of Ammonia from the Wastewater of Natural Gas Fertilizer Factory

Air-stripping method was used to remove ammonia from the wastewater collected from natural gas fertilizer factory. Different materials were used as packing materials for the air stripping system. The effect of pH over 10.5, air-water flow ratio, nature of packing materials, height of materials and initial influent concentration of ammonia on air stripping unit were investigated. An attempt has been made to find out the stripping con-stant. Stripping constant was found to be .001, 0014, .001 and .0009 for coal, plastic ring, stone chips and wood chips, respectively. Best result was found for plastic ring for its higher surface area. Wood chips did not give good result, because the chips amalgamate with each other and hence reduces the surface area.

Extraction and Stripping of Ytterbium (Ⅲ) from H_2SO_4 Medium by Cyanex 923

The extraction and stripping of ytterbium（ Ⅲ） from sulfuric acid medium using Cyanex 923 in heptane solution was investigated. The effects of extraetant concentration, pH and sulfate ion as well as stripping agents, acidity and temperature on the extraction and stripping were studied. The equilibrium constants and thermodynamic parameters, such as △n （10.76 kJ·mol^-1）, △G （-79.26 kJ·mol^-1） and △S （292.41 J·K^-1·mol^-1）, were calculated. The extraction mechanism and the complex species extracted were determined by slope analysis and FTIR spectra. Furthermore, it was found that the extraction of Yb （Ⅲ） from sulfuric acid medium by Cyanex 923 increased with pH, concentration of SO4^2-, HSO4^-, and extractant concentration, and approximately a quantitative extraction of Yb（ Ⅲ） was achieved at an equilibrium pH near 3.0, and the extracted complex was YbSO4（HSO4）·2Cyanex923（o）.

Surface Analysis of Chemical Stripping Titanium Alloy Oxide Films

The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films. The morphologies of the surface and cross-section of the oxide films before and after the films stripping were characterized by using scanning electron microscopy （SEM）. The microstructure and chemical compositions of the oxide films before and after the films stripping were investigated by using Raman spectroscopy （Raman） and X-ray photoelectron spectroscopy （XPS）. It was shown that the thickness of the oxide film was in the range of 5-6 μm. The oxide films were stripped for 2 to 8 min in the solution. Moreover, the effect of the stripping time on the efficiency of the film stripping was investigated, and the optimum stripping time was between 6-8 min. When the stripping solution completely dissolved the whole film, the α/β microstructure of the titanium alloy Ti-10V-2Fe-3Al was partly revealed. The stripping mechanism was discussed in terms of the dissolution of film delamination. The hydrogen peroxide had a significant effect on the dissolution of the titanium alloy anodic oxide film. The feasibility of the dissolution reaction also was evaluated.

Visual acuity and endothelial cell density with respect to the graft thickness in Descemet's stripping automated endothelial keratoplasty: one year results

AIM: To evaluate the visual acuity and endothelial cell density according to the thickness in Descemet’s stripping automated endothelial keratoplasty(DSAEK)one year after surgery.METHODS: DSAEK patients’ data were reviewed. Thirty seven eyes of 37 patients who underwent DSAEK for pseudophakic bullous keratopathy(PBK) were included in this study. Graft thickness was measured with optical coherence tomography(OCT) 12 mo after DSAEK. Eyes were divided into 3 groups based on the graft thickness:thick(】200 μm), medium-thick(150-200 μm) and thin(【150 μm). Best corrected visual acuity(BCVA),endothelial cells density(ECD) and complications were assessed and comparisons were done between groups.RESULTS: Median thickness of postoperative grafts was 188(range 73-317 μm). There was no significant difference in age, sex, preoperative BCVA, or follow-up period between DSAEK groups. At postoperative 12 mo,mean BCVA was 0.28±0.10 in thick graft group, 0.52±0.08 in medium-thick graft group, and 0.72 ±0.06 in thin graft group. Thin grafts showed better postoperative BCVA as compared with the medium-thick and thick grafts(P =0.001). Thick graft group had 1637.44 ±88.19-mm2,medium thick graft had 1764.50±34.28-mm2 and thin graft group had 1845.30 ±65.62-mm2. Thin graft group had better ECD at 12 mo after surgery(P =0.001).CONCLUSION: Thin grafts after DSAEK ensure better visual rehabilitation. Eyes with thin grafts had significantly lesser loss of ECD compared to eyes withmedium-thick and thick grafts one year after surgery.

DYNAMIC ANALYSIS OF GAS STRIPPING DURING ETHANOL FERMENTATION IN CSTR

The dynamic behavior of gas stripping during ethanol fermentation (GSEF) in a CSTR for a combined product-substrate inhibition case has been investigated in terms of bifurcation and regional stability theory. The region of optimal operating steady states and the effect of initial concentration on the attraction region have been established. The analytical results can be used to predict and promote the GSEF system moving towards an optimal operating steady state.

Kinetics of stripping of gold loaded in DBC organic phase by sodium sulfite

The kinetics of stripping of gold loaded in dibutyl carbito （DBC） organic phase by sodittm sulfite was investigated in a Lewis cell. After the stirring speed reached 400 r·min^-1, the reaction of gold stripping conformed with the pseudo-first-order reaction. The stripping rate of gold was in direct proportion to interracial area, concentration of sodittm sulfite and reaction temperature. The experimental results showed that the process of stripping gold was controlled by interfacial chemical reaction, and its activation energy was 36.06 kJ·mol^-1. The kinetics equation was put forward for gold stripping by sodium sulfite.

New insights into “dead lithium” during stripping in lithium metal batteries

Lithium (Li) metal attributes to the promising anode but endures the low Columbic efficiency (CE) and safety issues from the inactive Li accumulation. The metallic Li which is isolated from the lithium anode (named dead Li^(0)) consists the major component of the inactive Li. We systematically and meticulously investigated the formation and evaluation of dead Li^(0) during stripping process from electron transfer, the oxidation of Li^(0) to Li^(+) and the diffusion of Li^(+) through solid electrolyte interphase (SEI). The above-mentioned processes were regulated by adjusting the contact sites of electron channels, the dynamic rate of conversion from Li^(0) to Li^(+), and the structure as well as components of SEI. The design principles for achieving less dead Li^(0) and higher CE are proposed as a proof of concept in lithium metal batteries. This new insight sheds a comprehensive light on dead Li^(0) formation and guides the next-generation safe batteries for future application.

Extraction and stripping kinetics of copper(Ⅱ)by N902 using single drop technique

The kinetics of extraction and stripping of copper （Ⅱ） was investigated by the single drop technique with a new extractant N902 （a derivative of the salicylal-doxime） and the rate equations of extraction and stripping were derived, respectively. The apparent activation energies of extraction and stripping were estimated to be 20.14 kJ/mol and 30.0 k J/mol.

Clinical results of non-Descemet stripping endothelial keratoplasty

AIM： To investigate the impact of non-Descemet stripping endothelial keratoplasty（non-DSEK） on graft rejection rate,and its overall procedural effectiveness in patients.METHODS： Non-DSEK was performed on 65 eyes of 64 patients,and the procedural outcomes,including rejection episodes,failure and dislocation of the grafts,best corrected visual acuity（BCVA）,endothelial cell density（ECD）,and other complications,were analyzed retrospectively.RESULTS： Of the 65 eyes,63 recovered from bullous keratopathy with a clear cornea.The mean follow-up time was 26.4mo（range,6-84mo）.The mean BCVA improved from 1.70 log MAR preoperatively to 0.54 log MAR at 3mo,0.46 logM AR at 6mo,and 0.37 logM AR at 1y after surgery.The postoperative donor ECD of the 25 patients who successfully underwent specular microscopic examination was 1918±534 cells/mm^2（range,637 to 3056 cells/mm^2）,and the mean endothelial cell loss was 41.9% at 24 mo postoperatively.One eye developed secondary glaucoma and required regrafting via penetrating keratoplasty（PKP）.Another eye had postoperative graft failure due to rejection at 26 mo.Postoperative graft dislocation occurred in eight eyes.All of the eight dislocated grafts were reattached using air reinjection.CONCLUSION： Immunological graft rejection of the donor graft rarely occurs in non-DSEK.Therefore,non-DSEK is a safe,concise,and effective alternative to restore corneal decompensation when the Descemet membrane is disease-free.

Carbon Paste Electrode Modified by Surfactant for Anodic Stripping Voltammetric Determination of Sulphadiazine

he present paper covers the construction and behaviour of a mixed binder car-bon paste electrode modified by surfactant system appropriate for the anodic strip-ping voltammetric quantitation of sulphadiazine. The mixed binder consisted ofglycerol and liquid paraffin. On this electrode in a PH 8. 20 buffer solution sulpha-diazine yields a sensitive anodic stripping voltammetric wave at 0. 82 V. It can beused for the determination of trace amounts of drug, the linear range of the peakcurrent to the sulphadiazine concentration being from 1. 0 x 10-7 to 5. 0 x 10-5mol/L, and the detection limit being 6. 6 x 10-9 mol/L with a relative standard de-viation of 2. 6% (n= 15).The proposed method was used to determine the drug inurine samples.

Space-time principles of reducing stripping in furrow pits

The lower slope of furrow pits has following special features: small extent of weathering destruction, short time of production blasting damage, good arching effect of lower slope with small curvature radius, and good bottom effect of a pit end for transferring and bearing initial horizontal stresses in lower slope. The new principles provided theoretical basis for convex slope in furrow pits to reduce stripping. Similar phenomena and examples are supplied simultaneously.

Kinetic Study of Hydrothermal Stripping from Iron-Loaded Organic Phase

The iron-loaded organic phase of naphthenic acid-isooctyl alcohol-kerosene was prepared, and the process kinetics of hydrothermal stripping of iron from the phase was studied. Several factors affecting hydrothermal stripping, such as the polymer of naphthenic acid, initial concentrations of iron and naphthenic acid, temperature and agitation time, were investigated, and based on experimental results and theoretical analysis, two kinetic models were established.The stripping rate equation suggests that the hydrothermal stripping process activation energy is 96.4 kJ·mol-1 and the stripping is controlled by hydrolysis of naphthenic complex of iron. The values calculated by the stripping fraction equation comparatively accord with the experimental data.

A simulation study of a windowless gas-stripping room in an E//B neutral particle analyzer

The neutral particle analyzer(NPA)is one of the crucial diagnostic devices in a Tokamak facility.The stripping unit is one of the main parts of the NPA.A windowless gas-stripping room with two differential pipes has been constructed in a parallel electric and magnetic fields(E//B)NPA.The pressure distributions in the stripping chamber are simulated by ANSYS Fluent together with MolFlow+.Based on the pressure distributions obtained from the simulation,the stripping efficiency of the E//B NPA is studied using GEANT4.Hadron reaction physics is modified to track the charge state of each particle in a cross-section-based method in GEANT4.The transmission rates(R)and stripping efficiencies f_(+1)are examined for particle energies ranging from 20 to 200 keV with the input pressure(P_(0)),ranging from 20 to 400 Pa.According to the combined global efficiency,R×f_(+1),P_(0)=240 Pa is obtained as the optimum pressure for the maximum global efficiency in the incident energy range investigated.

The Effect of Atmospheric Plasma Paint Stripping on the Fatigue Crack Growth Properties of Aluminium Substrates

Paint removal is a common maintenance requirement for aircraft as well as naval and land vehicles, since external paint gets damaged and loses much of its corrosion protection effectiveness with time. Paint removal is also conducted when metallic aircraft structures are inspected periodically for fatigue cracks and corrosion. The conventional methods of removing paint employed throughout the Canadian Forces mainly include chemical stripping and abrasive media blasting. Chemical stripping involves the use of hazardous chemicals, which are high in Volatile Organic Compounds (VOC) and Hazardous Air Pollutants (HAP). Abrasive media blasting typically results in a substantial quantity of solid waste consisting of paint and blast residues. Such waste is subject to control under increasingly stringent environmental and safety regulations and its disposal is costly. The new Atmospheric Plasma (AP) paint removal process purports to be a high chemical energy, low thermal energy (cold plasma process), that should not damage temperature sensitive substructures, such as heat treated aerospace aluminium alloys. Fatigue strength is one of the key properties in aircraft structures. In order for AP paint stripping to be accepted as an aerospace industry standard paint removal process, it must be thoroughly tested to demonstrate that it does not adversely affect the fatigue properties of the substrate. This paper investigates effect of the paint removal process on fatigue crack growth of 7075-T6 and 2024-T3 aluminium panels.

Design of the stripping unit and the electromagnetic analysis unit for the E//B NPA on HL-2A/2M tokamak

An E//B neutral particle analyzer is under development for fast ion diagnosis on HL-2A/2 M tokamak.The stripping unit is composed of a stripping room(equipped with two differential tubes and a gas supply bellows),a vacuum chamber and a vacuum pumping system.The stripping efficiency of the stripping room is calculated in the form of global efficiency R×f_(+1),where R is the non-scattered-away rate and f_(+1)is the fraction of charge state+1.The magnetic field of the E//B analyzer is produced with a permanent magnet.The yoke and the poles of the magnet are made of mild steel and the magnet plates are made of Nd Fe B.The magnetic poles are specially designed to focus the ion trajectories and to increase the use rate of the magnet.The shape of the magnet and the electric plates are carefully designed so that the ions are dispersed into two lines of H^(+) and D^(+) on the detector plane.For each line,the energy increases from 10 to 200 ke V from one side to another.