Distribution of Microelements and Their Influence on the Corrosion Behavior of Aluminum Foil

The distribution of microelement Fe, Si, Cu and Mg in the surface layer of aluminum foil annealed at 300℃ and 500℃ were determined by secondary ion mass spectrometer. The corrosion structure produced by electrochemical etching was also observed. It was found that the Mg concentration at external surface was increased exponentially over the fourth degree and promoted by higher annealing temperature, which will increase the number of corrosion pits inside the large grains, and therefore the specific capacity of the foils for electrolytic capacitors. The similar effects of microelement Fe, Si and Cu were not so strong.

Impact of high dose Kr^+ ion irradiation on the corrosion behavior and microstructure of Zircaloy-4

In order to investigate the ion irradiation effect on the corrosion behavior and microstructure of Zircaloy-4, the Zircaloy-4 film were prepared by electron beam deposition on the Zircaloy-4 specimen surface and irradiated by Kr ions using an accelerator at an energy of 300 keV with the dose from 1×1015 to 3×1016ions/cm2. The post-irradiation corrosion tests were conducted to rank the corrosion resistance of the resulting specimens by potentiodynamic polarization curve measurements in a 0.5 mol/L H2SO4 water so- lution at room temperature. Transmission electron microscopy (TEM) was employed to examine the microstructural change in the surface. The potentiodynamic tests show that with the irradiation dose increasing, the passive current density, closely related to the surface corrosion resistance, decreases firstly and increases subsequently. The mechanism of the corrosion behavior transformation is due to the amorphous phase formation firstly and the amorphous phase destruction and the polycrystalline structure formation in the irradiated surface subsequently.

Corrosion Behavior of Mg-Zn-Y Alloy with Long-period Stacking Ordered Structures

Mg-Zn-Y alloys with long-period stacking ordered structures were prepared by an ingot casting method. The corrosion performance of Mg-Zn-Y alloys was studied by combining gas-collecting test, immersion test and electrochemical measurements in order to determine the corrosion rate and mechanism of the alloys. The results showed that the volume fraction of Mg（12）YZn phase increased and the shape of the Mg（12）YZn phase changed from discontinuous to continuous net-like with increasing Zn and Y content. The corrosion rate of the alloys greatly depended on the distribution and volume fraction of the Mg（12）YZn phase. Corrosion products appeared at the junction of Mg phase and Mg（12）YZn phase, indicating that the Mg（12）YZn phase accelerated galvanic corrosion of Mg matrix. Mg（97）Zn1Y2 alloy shows the lowest corrosion rate due to the continuous distribution of Mg（12）YZn phase.

Corrosion Behavior of S450EW Low-alloy Weathering Steel in Cyclically Alternate Corrosion Environments

Weathering steel is widely used in various fields due to its excellent mechanical properties and high corrosion resistance. The effect of chromium content on the S450 EW weathering steel in cyclic immersion test was studied. The results indicated that the corrosion resistance of S450 EW weathering steel is closely related to chromium content. The addition of chromium significantly inhibited the weathering steel corrosion. The corrosion rate of experimental steel after 96 h immersion was 1.101 g·m-2·h-1. The rust of S450 EW weathering steel was mainly constituted of Fe OOH and Fe3O4 phase, and the elevation of chromium content promoted the formation of α-Fe OOH. The fine precipitates of the two phases contributed to the formation of dense dust layer of test steel. Furthermore, the increase of chromium is beneficial for the cure of original defects and cracks of the rust layer via the enrichment of chromium. The corrosion potential and the resistance of corrosion process were thus increased, protecting the experimental steel from further corrosion. A S450 EW steel with corrosion resistance more than 1.5 times of Q450NQR1 steel was prepared.