Mechanical responses of underground carriageway structures due to construction of metro tunnels beneath the existing structure:A case study

To understand the mechanical response pattern of the existing structure and ground due to the construction of metro tunnels underneath,the finite difference method is adopted to study the torsional deformation and stress variation of the existing structure and the effect of underground carriageway structures on the surface subsidence.The curves of the maximum differential subsidence,torsion angle,and distortion of the cross-section of the existing structure show two peaks in succession during traversing of two metro tunnels beneath it.The torsion angle of the existing structure changes when the two tunnels traverse beneath it in opposite directions.The first traversing of the shield tunnel mainly induces the magnitude variation in torsional deformation of the existing structure,but the second traversing of the subsurface tunnel may cause a dynamic change in the magnitude and form of torsional deformation in the existing structure.The shielding effect can reduce the surface subsidence caused by metro tunnel excavation to a certain extent,and the development trend of subsidence becomes slower as the excavation continues.

Numerical Simulations of Structural Deformation and Fluid Flow in Xiangshan Deposit

The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical simulation. In order to find the most favorable locations of mineralization and to help further mineral exploration, a coupling deforma- tion and fluid flow model has been established to describe the mineralization process. In this model, the simulation re- constructs the strata deformations under fields of compressive stress and thrust structure on the hanging wall of the Zou-Shi fault. Compared with practical information, the simulation results are consistent with the No. 51 exploration section of the western Xiangshan. In addition, on the basis of geological information provided by previous investigators, the model simulates the flow process of fluids under compressive stress fields. The result suggests that many tensional areas are formed, which can help the fluid flowing upward from deeper parts. The fluid is easy to concentrate on the breccia fractured zone between two volcanic layers, especially on the intersection parts with faults, resulting in the for- mation of favourable locations of mineralization. In addition, the model is significant in guiding the exploration of ura- nium deposits in the western Xiangshan and provides clues for further exploration of deposits.

Vertical Differential Structural Deformation of the Main Strike-slip Fault Zones in the Shunbei Area,Central Tarim Basin:Structural Characteristics,Deformation Mechanisms,and Hydrocarbon Accumulation Significance

Vertical differential structural deformation(VDSD),one of the most significant structural characteristics of strike-slip fault zones(SSFZs)in the Shunbei area,is crucial for understanding deformation in the SSFZ and its hydrocarbon accumulation significance.Based on drilling data and high-precision 3-D seismic data,we analyzed the geometric and kinematic characteristics of the SSFZs in the Shunbei area.Coupled with the stratification of the rock mechanism,the structural deformations of these SSFZs in different formations were differentiated and divided into four deformation layers.According to comprehensive structural interpretations and comparisons,three integrated 3-D structural models could describe the VDSD of these SSFZs.The time-space coupling of the material basis(rock mechanism stratification),changing dynamic conditions(e.g.,changing stress-strain states),and special deformation mechanism of the en echelon normal fault array uniformly controlled the formation of the VDSD in the SSFZs of the Shunbei area.The VDSD of the SSFZs in this area controlled the entire hydrocarbon accumulation process.Multi-stage structural superimposing deformation influenced the hydrocarbon migration,accumulation,distribution,preservation,and secondary adjustments.

Structural deformation and fluid flow from East Sichuan to the northwestern periphery of the Xuefeng Uplift,China

Hydrocarbon preservation conditions have restricted exploration in the Middle and Upper Yangtze,and structural deformation and fluid activity have played an important role in the origin and preservation of oil and gas.In order to study that how the deformation and fluid activity impact the hydrocarbon preservation,we did some field work and collected some calcite vein samples for analysis of deformation periods using acoustic emission and fluid inclusions.Combined with previous studies,the strata distribution,tectonic deformation and fluid characteristics show that there are three structural belts in the study area：East Sichuan,West Hunan and Hubei and the northwestern periphery of the Xuefeng Uplift,and that their tectonic deformation style,fluid inclusion characteristics and hydrocarbon preservation are different.The breakthrough thrusts were well developed in the anticline core,and a lot of hydrocarbon inclusions were found in calcite veins around the thrusts in East Sichuan.The breakthrough thrusts were only in the syncline core in West Hunan and Hubei,and the brine inclusions did not contain hydrocarbon in calcite veins around the thrusts.Many breakthrough thrusts were found in the northwestern periphery of the Xuefeng Uplift,where there were only rare calcite veins.The deformation and hydrocarbon inclusion indicated that when there was no fault breakthrough in East Sichuan,the Paleozoic covered by the Triassic regional cap was good for hydrocarbon preservation.The strata above the Lower Paleozoic were denuded,and lots of brine inclusions and deep infiltration of surface water were found in the West Hunan and Hubei,so only the part of the syncline area with a well developed Silurian regional cap had good preservation conditions.Intense tectonic movements and denudation were widely developed in the northwestern periphery of the Xuefeng Uplift,where there were only paleo-reservoirs,non-hydrocarbon fluid activity and poor preservation conditions.

STRAIN INDUCED STRUCTURAL TRANSITION OF INTERFACES AND TWINS IN A HOT－DEFORMED DUAL－PHASE TIAL ALLOY

The structure characteristics of a2/γinterfaces and the features of deformation twins in a quasi-isothermal forged Ti-45Al-10Nb alloy were studied by highresolution transmission electron microscopy. Three types of strain induced a2/γinterfaces and two types of strain induced twin boundaries were identified The most,important features are high density of ledges and the existence of I/3[111] Frank partial dislocation. Mechanisms for the formation these interfaces were proposed Two types of deformation twins were observed These deformation twins always start from the ledges it seems that ledges at interfaces are important features of interfacial structure for the mechanical behavior of alloys.

Structural deformation of nitro group of nitromethane molecule in liquid phase in an intense femtosecond laser field

The structural deformation of NO2 group induced by an intense femtosecond laser field of liquid nitromethane（NM）molecule is detected by time-and frequency-resolved coherent anti-Stokes Raman spectroscopy（CARS） technique with the intense pump laser. Here, we present the mechanism of molecular alignment and deformation. The CARS spectra and its FFT spectra of liquid NM show that the NO2 torsional mode couples with the CN symmetric stretching mode and that the NO2 group undergoes ultrafast structural deformation with a relaxation time of 195 fs. The frequency of the NO2 torsional mode in liquid NM（50.8±0.3 cm^-1） at room temperature is found. Our results prove the structural deformation of two groups in liquid NM molecule occur simultaneously in the intense laser field.

AN ANALYTICAL METHOD FOR SOLVING INTERNAL FORCES AND DEFORMATIONS OF BAR-SYSTEM STRUCTURE IN SPACE

In this paper, based on the idea of finite element method, the initial parametric method in bending, problem of a beam is extended to analyse the bar-system structure by employing Dirac function and llcavisidc step function.Then a new method for analysing the internal forces and deformations of bar-system structure in space is suggested by improving the mixed method in statically indeterminate structure.The inferred process and obtained answer will be more succinct and accurate when the problem of internal forces and deformations of bar-system structure is analysed by using the new method provided in this paper.

Lacustrine sedimentary responses to earthquakes—soft-sediment deformation structures since late Pleistocene:A review of current understanding

The traces left by earthquakes in lacustrine sediments are studied to determine the occurrence of ancient earthquakes by identifying seismically induced soft-sediment deformation structures(SSDS).Dating can help reconstruct the relative frequency of earthquakes.Identifying seismically induced seismites,which carry abundant seismic information from numerous SSDS,is both critical and challenging.Studying the deformation mechanism of SSDS and learning about the common criteria of seismically induced SSDS improve the identification of earthquake triggers.With better research into SSDS,seismic events can be effectively captured,and temporal constraints can be carried out by 14C dating and optically stimulated luminescence(OSL)dating to identify and date the occurrence of ancient earthquakes.The present contribution primarily addresses the meaning and mechanism of SSDS and their relationship with earthquake magnitude as well as the common criteria of the SSDS induced by earthquakes.

Numerical simulation of fluid-thermal-structural coupling characteristics of stratospheric non-rigid airship

The voluminous stratospheric non-rigid airship is very sensitive to the external thermal environment.The temperature change of internal gas caused by the variation in the external ther-mal environment and wind speed will lead to a change in the shape and buoyancy of the airship,thereby affecting its flight control.The traditional static analysis method is difficult to accurately reflect this fuid-thermal-structural coupling process.In this paper,the iterative analysis method was established for the fluid-thermal-structural coupling effect of stratospheric non-rigid airship based on the models of fluid,thermal,and structural deformation.Considering the load such as the internal thermal effect and external flow field of the airship,the simulation of the thermo-induced structural deformation effect was conducted using Fluent and Abaqus software.The influ-ence of local time and external wind speed on the structural deformation,volume,and equilibrium altitude of the airship was analyzed.The results demonstrate that,at low wind speed,the influence of aerodynamic pressure on the deformation of the airship is negligible.However,a great amount of heat is carried away by the wind,then the structural deformation caused by internal and external pressure difference is alleviated and the equilibrium altitude of the airship change obviously.This can serve as a guideline for the design and flight test of the long-endurance stratospheric non-rigid airship.

Superplastic extensibility deformation of Al-3%Mn alloy with submicrometer grain size

Submicrometer-grained （SMG） Al-3%Mn （mass fraction） alloy specimens with initial grain size of -0.3 μm were produced by ball milling for 3 h. The Al-3%Mn specimens which were cold rolled with a strain rate of 1×10^-3- 1×10^-2 s-1 at room temperature show high extensibility to failure more than 2500%. Microstructures of pure Al and Al-3%Mn alloy at as-milled and cold-rolled state were examined using X-ray diffraction and transmission electron microscopy （TEM）. Based on the microstructure analysis, it is established that the mechanism of the continued plastic deformation in SMG Al-3%Mn alloy consists of dislocation slip, grain boundary sliding companied by dynamic recovery and recrystallization, and dynamic recrystallization is a main control factor of the large plastic deformation.

^(40)Ar/^(39)Ar Dating of Deformation Events and Reconstruction of Exhumation of Ultrahigh-Pressure Metamorphic Rocks in Donghai, East China

Recent investigations reveal that the ultrahigh-pressure metamorphic (UHPM) rocks in the Donghai region of East China underwent ductile and transitional ductile-brittle structural events during their exhumation. The earlier ductile deformation took place under the condition of amphibolite facies and the later transitional ductile-brittle deformation under the condition of greenschist facies. The hanging walls moved southeastward during both of these two events. The 40Ar/39Ar dating of muscovites from muscovite-plagioclase schists in the Haizhou phosphorous mine, which are structurally overlain by UHPM rocks, yields a plateau age of 218.0±2.9 Ma and isochron age of 219.8Ma, indicating that the earlier event of the ampibolite-facies deformation probably took place about 220 Ma ago. The 40Ar/39Ar dating of oriented amphiboles parallel to the movement direction of the hanging wall on a decollement plane yields a plateau age of 213.1±0.3 Ma and isochron age of 213.4±4.1 Ma, probably representing the age of the later event. The dating of pegmatitic biotites and K-feldspars near the decollement plane from the eastern Fangshan area yield plateau ages of 203.4±0.3 Ma, 203.6±0.4 Ma and 204.8±2.2 Ma, and isochron ages of 204.0±2.0 Ma, 200.6±3.1 Ma and 204.0±5.0 Ma, respectively, implying that the rocks in the studied area had not been cooled down to closing temperature of the dated biotites and K-feldspars until the beginning of the Jurassic (about 204 Ma). The integration of these data with previous chronological ages on the ultrahigh-pressure metamorphism lead to a new inference on the exhumation of the UHPM rocks. The UHPM rocks in the area were exhumed at the rate of 3-4 km/Ma from the mantle (about 80-100 km below the earth's surface at about 240 Ma) to the lower crust (at the depth of about 20-30km at 220 Ma), and at the rate of 1-2 km/Ma to the middle crust (at the depth of about 15 km at 213 Ma), and then at the rate of less than 1 km/Ma to the upper crust about 10 km deep at about 204 Ma.

Polyphase Tectonic Events and Cenozoic Basin-Range Coupling in the Tianshan Belt,Northwestern China

Studies show that the Tianshan orogenic belt was built in the late stage of the Paleozoic, as evidenced by the Permian red molasses and foreland basins, which are distributed in parallel with the Tianshan belt, indicating that an intense folding and uplifting event took place. During the Triassic, this orogenic belt was strongly eroded, and basins were further developed. Starting from the Jurassic, a within-plate regional extension occurred, forming a series of Jurassic-Paleogene extensional basins in the peneplaned Tianshan region. Since the Neogene, a collision event between the Indian and the Eurasian plates that took place on the southern side of the Tianshan belt has caused a strong intra-continental orogeny, which is characterized by thrusting and folding. Extremely thick coarse conglomerate and sandy conglomerate of the Xiyu Formation of Neogene System were accumulated unconformably on the Tianshan piedmont. Studies have revealed that the strong compression caused by the Indian-Eurasian collision had a profound influence over the orogenic belt in the hinterland, and MesozoiC-Cenozoic brittle deformed structures superposed on the ductile deformed Paleozoic rocks. The Mesozoic extensional basins were converted into Cenozoic compressional basins. The deformation in the basins is featured by step thrusts and fault-related folds. Statistics of joints show that the principal compressive stress since the Neogene is in a N-S direction. Meanwhile, owing to the underthrusting of the basin toward the orogenic belt, the Paleozoic strata were thrust on the Meso-Cenozoic rocks as tectonic slices, revealing distinct kinematic features in different geologic units. The basin-range coupling zones are characterized by intensive compression, folding and thrusting, accompanied by local sub-E-W-trending strike-slip faults. In the Tianshan region, Cenozoic thrusting is the most common basin-range coupling mode. The folding and faulting of Mesozoic sedimentary rocks, spontaneous combustion of Jurassic coal layers and formation of sintered rocks, the Cenozoic earthquakes and active faulting, and the unique mosaic pattern of basin-range framework of Xinjiang are all products of tectonism since the Neogene.

Advances and Overview of the Study on Paleo-earthquake Events: A Review of Seismites

The distribution and formation mechanisms of typical identified seismites are analyzed based on various factors from plate tectonic positions, types of sedimentary basins and properties of seismogenic faults to focal mechanisms.Especially, structural styles, reserved positions, activity times, formation mechanisms and dynamics of soft-sediment deformation structures triggered by seismic activity are systematically analyzed.According to the genetic types of seismites, we propose 5 categories, including liquefied deformation, thixotropic deformation, hydroplastic deformation, superimposed gravity driving deformation and brittle deformation.Further, based on the main genetic types, composition of sediments and deformation styles, we draw up 35 secondary classifications.To determine paleo-seismic sequences in different times, activities of seismogenic faults, high-resolution tectonic events in one main tectonic movement and paleo-tectonic settings, and to understand the inducing mechanisms of paleo-earthquakes and ecologic environment evolution, researching on seismites are of great significance.Combing multiple approaches to identify the paleoearthquake records, simulating experiments on various soft-sediment deformation structures triggered by different magnitudes of shocking, dating precisely on paleo-seismic events, impacting on paleogeography and biological environment and on energy and resources domain are the frontiers of paleoseismic research.

A Preliminary Study on the Soft–Sediment Deformation Structures in the Late Quaternary Lacustrine Sediments at Tashkorgan, Northeastern Pamir, China

This study identified soft-sediment deformation structures （SSDS） of seismic origin from lacustrine sediments in the late Quaternary paleo-dammed lake at Tashkorgan, northeastern Pamir. The observed deformation structures include sand dykes, liquefied diapir and convolute structures, gravity induced SSDS, and thixotropic pillar and tabular structures. We conducted a preliminary study on the morphology, formation and trigger mechanisms of pillar and tabular structures formed by liquefaction of underlying coarse sand and thixotropy of the upper silty clay. The regional tectonic setting and distribution of lacustrine strata indicate that the most probable trigger for the SSDS in lacustrine sediments was seismic activity, with an approximate earthquake magnitude of M〉6.0; the potential seismogenic fault is the southern part of the Kongur normal fault extensional system. AMS ^4C dating results indicate that the SSDS were formed by seismic events occurring between 26050±100 yrBP and 22710±80 yrBP, implying intense fault activity in this region during the late Pleistocene. This study provides new evidence for understanding tectonic activity and regional geodynamics in western China.

Late Cretaceous Transpressional Fault System: A Case Study of the Yishu Fault Belt, Shandong Province, Eastern China

On the basis of field observations of the structures of three profiles from the Linshu region, deformation characteristics and the tectonic background of the Yishu fault belt in the Late Cretaceous–Early Cenozoic have been discussed in detail.Three structural profiles, whose deformations consist mainly of earlier transpressional faults and later normal faults, were developed for the Mengtuan Formation of the Lower Cretaceous Dasheng Group.Typical positive flower structures, duplex structures, and break-through faults were found in these profiles.On the basis of analyses of the structural deformation and previous geochronological studies, it was concluded that the earlier transpressional faults of the profiles were triggered by the sinistral transpression of the Yishu fault belt in the Late Cretaceous–Early Paleogene, and that the later normal faults, formed during the Late Paleogene–Neogene extension, truncated the earlier transpressional faults.With consideration of the tectonic evolution of the Tan-Lu fault belt and the different drift directions of the Pacific plate since the Cretaceous, we suggest that the major tectonic events of the Late Cretaceous–Neogene in eastern China were mainly controlled by the subduction of the Pacific plate.

MPS-FEM Coupled Method for Study of Wave-Structure Interaction

Nowadays,an increasing number of ships and marine structures are manufactured and inevitably operated in rough sea.As a result,some phenomena related to the violent fluid-elastic structure interactions(e.g.,hydrodynamic slamming on marine vessels,tsunami impact on onshore structures,and sloshing in liquid containers)have aroused huge challenges to ocean engineering fields.In this paper,the moving particle semi-implicit(MPS)method and finite element method(FEM)coupled method is proposed for use in numerical investigations of the interaction between a regular wave and a horizontal suspended structure.The fluid domain calculated by the MPS method is dispersed into fluid particles,and the structure domain solved by the FEM method is dispersed into beam elements.The generation of the 2D regular wave is firstly conducted,and convergence verification is performed to determine appropriate particle spacing for the simulation.Next,the regular wave interacting with a rigid structure is initially performed and verified through the comparison with the laboratory experiments.By verification,the MPS-FEM coupled method can be applied to fluid-structure interaction(FSI)problems with waves.On this basis,taking the flexibility of structure into consideration,the elastic dynamic response of the structure subjected to the wave slamming is investigated,including the evolutions of the free surface,the variation of the wave impact pressures,the velocity distribution,and the structural deformation response.By comparison with the rigid case,the effects of the structural flexibility on wave-elastic structure interaction can be obtained.

The Seismic Induced Soft Sediment Deformation Structures in the Middle Jurassic of Western Qaidamu Basin

Intervals of soft-sediment deformation structures are well-exposed in Jurassic lacustrine deposits in the western Qaidamu basin. Through field observation, many soft-sediment deformation structures can be identified, such as convoluted bedding, liquefied sand veins, load and flame structures, slump structures and sliding-overlapping structures. Based on their genesis, soft-sediment deformation structures can be classified as three types： seismic induced structures, vertical loading structures, and horizontal shear structures. Based on their geometry and genesis analysis, they are seismic-induced structures. According to the characteristics of convoluted bedding structures and liquefied sand veins, it can be inferred that there were earthquakes greater than magnitude 6 in the study area during the middle Jurassic. Furthermore, the study of the slump structures and sliding- overlapping structures indicates that there was a southeastern slope during the middle Jurassic. Since the distance from the study area to the Altyn Mountain and the Altyn fault is no more than 10km, it can be also inferred that the Altyn Mountain existed then and that the AItyn strike-slip fault was active during the middle Jurassic.

Earthquake-induced Soft-sediment Deformation Structures in the Dengfeng Area,Henan Province,China:Constraints on Qinling Tectonic Evolution during the Early Cambrian

Soft-sediment deformation structures are abundant in the Cambrian Zhushadong and Mantou formations of the Dengfeng area, Henan Province, China. Soft-sediment deformation structures of the Zhushadong Formation consist of fluidized deformation, synsedimentary faults, seismo-folds and plastic deformation; the Mantou Formation is dominated by small-scale horst faults, intruded dikes, fluidized veins, and seismo-cracks. These structures are demonstrated to be earthquake-related by analysis of trigger mechanisms, and may indicate the activity of the Qinling tectonic belt during the early Cambrian. Furthermore, the assemblages of soft-sediment deformation structures altered with time： large-scale, intense deformation in the Zhushadong Formation alters to small-scale, weak deformation in the Mantou Formation. This striking feature may have been caused by changes in hypocentral depth from deep-focus to shallow-focus earthquakes, indicating that the Qinling tectonic belt developed from the subduction of the Shangdan Ocean to the extension of the Erlangping back-arc basin. This study suggests that soft-sediment deformation structures can be used to reveal the activity of a tectonic belt, and, more importantly, changes in deformation assemblages can track the evolution of a tectonic belt.

Tectonically deformed coal types and pore structures in Puhe and Shanchahe coal mines in western Guizhou

To evaluate the effect of tectonic deformation on coal reservoir properties, we provide an analysis of the types of tectonically deformed coal, macroand microscopic deformation and discuss pore structural characteristics and connectivity based on samples from the Puhe and Shanchahe coal mines. Our research shows that the tectonically deformed coal mostly includes cataclastic structural coal, mortar structural coal and schistose structural coal of a brittle deformation series. The major pore structures of different types of tectonically deformed coal are transitional pores and micropores. The pore volumes of macropores and visible fracture pores produced by structural deformations vary over a large range and increase with the intensity of tectonic deformation. Mesopores as connecting passages develop well in schistose structural coal. According to the shapes of intrusive mercury curves, tectonically deformed coal can be divided into parallel, open and occluded types. The parallel type has poor connectivity and is relatively closed; the open type reflects uniformly developed open pores with good connectivity while the occluded type is good for coalbed methane enrichment, but has poor connectivity between pores.

Residual Stress Relaxation of Thin‑walled Long Stringer Made of Aluminum Alloy 7050‑T7451 under Transportation Vibration

Thin-walled long stringer made of aluminum alloy 7050-T7451 is prone to deformation during transportation,so a research of residual stress relaxation was launched in this paper.The transport resonance stress of long stringer was analyzed based on the power spectral density of road transport acceleration.The residual stress relaxation experiment of aluminum alloy 7050-T7451 under different equivalent stress levels was designed and carried out.According to the amount of residual stress relaxation in the experiment,an analytical model was established with the equivalent stress level coefficient.The deflection range of long stringer was evaluated under different damping ratios.The results show that when the equivalent stress exceeds 0.8σ0.2,the residual stress relaxation of the thin-walled samples occurs.The residual stress relaxation increases linearly with the equivalent stress,which is logarithmically related to the loading cycle.The deformation caused by residual stress relaxation of the long stringer is proportional to the square of the length and the bending moment caused by stress rebalance,and inversely proportional to the moment of inertia of the structure.As the damping ratio decreases from 0.03 to 0.01,the total deflection of the long stringer increases from 0 to above 1.55 mm.