Bio-Based Waterborne Poly(Vanillin-Butyl Acrylate)/MXene Coatings for Leather with Desired Warmth Retention and Antibacterial Properties

This study presents a solvent-free,facile synthesis of a bio-based green antibacterial agent and aromatic monomer methacrylated vanillin(MV)using vanillin.The resulting MV not only imparted antibacterial properties to coatings layered on leather,but could also be employed as a green alternative to petroleum-based carcinogen styrene(St).Herein,MV was copolymerized with butyl acrylate(BA)to obtain waterborne bio-based P(MV-BA)miniemulsion via miniemulsion polymerization.Subsequently,MXene nanosheets with excellent photothermal conversion performance and antibacterial properties,were introduced into the P(MV-BA)miniemulsion by ultrasonic dispersion.During the gradual solidification of P(MV-BA)/MXene nanocomposite miniemulsion on the leather surface,MXene gradually migrated to the surface of leather coatings due to the cavitation effect of ultrasonication and amphiphilicity of MXene,which prompted its full exposure to light and bacteria,exerting the maximum photothermal conversion efficiency and significant antibacterial efficacy.In particular,when the dosage of MXene nanosheets was 1.4 wt%,the surface temperature of P(MV-BA)/MXene nanocomposite miniemulsioncoated leather(PML)increased by about 15℃ in an outdoor environment during winter,and the antibacterial rate against Escherichia coli and Staphylococcus aureus was nearly 100%under the simulated sunlight treatment for 30 min.Moreover,the introduction of MXene nanosheets increased the air permeability,water vapor permeability,and thermal stability of these coatings.This study provides a new insight into the preparation of novel,green,and waterborne bio-based nanocomposite coatings for leather,with desired warmth retention and antibacterial properties.It can not only realize zerocarbon heating based on sunlight in winter,reducing the use of fossil fuels and greenhouse gas emissions,but also improve ability to fight off invasion by harmful bacteria,viruses,and other microorganisms.

Styrene epoxidation catalyzed by polyoxometalate/quaternary ammonium phase transfer catalysts: The effect of cation size and catalyst deactivation mechanism

Catalytic epoxidation of alkenes is an important type of organic reaction in chemical industry,and the deep insight into catalyst deactivation will help to develop new epoxidation process.In this work,series of quaternary ammoniums bearing different cationic sizes,i.e.MTOA+(methyltrioctylammonium,[(C_(8)H_(17))_(3)CH_(3)N]+),HTMA+(hexadecyltrimethylammonium,[(C_(16)H_(33))(CH_(3))_(3)N]+) and DMDOA+(dimethyldioctadecylammonium,[(C_(18)H_(37))_(2)(CH_(3))_(2)N]+) were incorporated with polyoxometalate (POM) anions to prepare phase transfer catalysts (PTCs),which were used in the styrene epoxidations.Among them,(MTOA)_(3)PW_(4)O_(24)exhibits the best catalytic performance judged from the highest styrene conversion rate(52%) and styrene oxide selectivity (93%),during which the styrene epoxidation conditions were optimized.Meanwhile,the deactivation mechanism of this kind of PTCs was proposed firstly,i.e.in the case of low H_(2)O_(2) content,the oxidant can only be used in the styrene epoxidation,in which the catalyst can transform into stable Keggin-type POM.But when the content of H_(2)O_(2) is higher,the excess H_(2)O_(2) can reactivate the Keggin-type POM into active (PW_(4)O_(24))_(3)-anions,which can trigger the ring-opening polymerization of styrene oxide.Consequently,the catalyst is deactivated by adhered poly(styrene oxide)irreversibly,which was determined by NMR spectra.In this situation,the active moiety{PO_(4)[WO(O_(2))_(2)]_(4)}_(3)-in phase-transfer catalytic system can break into some unidentified species with low W/P ratio with the presence of epoxides.This work will be beneficial for the design of new PTCs in alkene epoxidation in fine chemical industry.

One-pot synthesis of ordered mesoporous Cu-KIT-6 and its improved catalytic behavior for the epoxidation of styrene:Effects of the pH value of the initial gel

The heterogeneously copper-catalyzed oxidative cleavage of styrene was studied using copper-doped mesoporous KIT-6（CU-KIT-6_x） prepared via pH adjustment（where x is the pH：1.43,2.27,3.78,3.97,4.24 or 6.62）.Variations in the catalyst structure and morphology with pH values were characterized by X-ray power diffraction,nitrogen adsorption-desorption analysis,transmission electron microscopy and X-ray photoelectron spectroscopy.As the pH value applied during the initial synthesis,the resulting Cu-KIT-6_x exhibited different structural,textural and surface characteristics,especially in terms of specific copper species and copper content At a pH value of 3.78,approximately 4.6 wt%copper（Ⅱ） was successfully incorporated into the framework of the initial KIT-6,in the form of-Cu-O-Si- groups.The catalytic performance of each catalyst was evaluated by following the epoxidation of styrene,employing tert-butyl hydroperoxide as the oxidant and CH_3CN as the solvent.A significant styrene conversion of 43.5%with 86.6%selectivity for the desired styrene epoxide was obtained over the Cu-KIT-63.78.A higher Cu content,an ordered cubic laid mesoporous architecture and various specific textural characteristics all combined to endow the Cu-KIT-63.78 with high catalytic activity and good stability.

An Investigation on the Polymerization of Styrene by Fluorescence Probe Technique

The polymerization of styrene is monitored by pyrene excimer formation. The ratio of monomer to excimer intensities ( I m/ I e) of pyrene increases as polymerization proceeds. The increase of I m/ I e is ascribed to the increase of microviscosity surrounding the probes forming excimer during polymerization. The linear relationship between the changing rate of I m/ I e and the polymerization rate of styrene is obtained. Therefore, I m/ I e may be used to monitor the progress of the polymerization of styrene.

苯丙乳液的裂解气相色谱-质谱分析

The products of thermal desorption were generated under the temperature of 280 ℃ and were analyzed by gas chromatography-mass spectrometry with capillary column,the residual monomer styrene was no detected.The products of pyrolysis were generated under the temperature of 550 ℃ and were analyzed by chromatography-mass spectrometry,14 compounds were detected.

苯乙烯绿色氧化合成苯甲酸的机理研究

本文报道了用GC-MS跟踪了双氧水氧化苯乙烯为苯甲酸的全过程,研究结果发现4种主要物质苯乙烯、1-苯基邻二醇、羟基苯乙酮及苯甲酸含量随反应时间的变化关系,从而提出了其主要氧化机理可能为:苯乙烯首先经过环氧化反应,水解生成1-苯基邻二醇,然后1-苯基邻二醇氧化为羟基苯乙酮,羟基苯乙酮最后氧化为苯甲酸.……

Study on Structure and Performance of Starch and Styrene Graft Copolymer

[Objective] The paper was to study the structure and performance of starch and styrene graft copolymer. [Method] The microscopic structure of corn starch and styrene graft copolymer was analyzed by using infrared spectrum and scanning electron microscope, and the property of starch and styrene graft copoly- mer was confirmed through grinding experiment, tensile strength, water absorption rate, hot water resistance properties and enzymatic properties analysis. [Result] The starch and styrene graft copolymer had the properties of thermoplastic and microbial degradation. IConclusion] The starch and styrene graft copolymer is expected to be developed as a biodegradable material.

Synthesis of Ln-doped MCM-41 mesoporous materials and their catalytic performance in oxidation of styrene

Using cetyl-trimethyl-ammonium bromide （CTMAB） as the template agent and tetraethylorthosilicate （TEOS） as the silica source, the MCM-41 mesoporous materials were synthesized with La or Ce incorporated in the framework under hydrothermal conditions. The structure and the state of La or Ce were investigated through the analyses of XRD, nitrogen adsorption-desorption, FT-IR, and UV-Vis. XRD and N2 adsorption-desorption results showed that Ln-MCM-41 exhibited the loss of the lattice ordering of the MCM-41 construct, and larger unit cell parameter and pore diameter than pure silica MCM-41. The FT-IR and UV-Vis results indicated the presence of isolated tetra-coordinated La or Ce ions in the framework and other Ln species dispersed highly on the Ln-MCM-41 surface simultaneously. Furthermore, their catalytic behaviors in the oxidation of styrene were studied using H2O2 as the oxidant. The La-MCM-41 catalysts exhibited high reactivity and the reactivity increased with the increase of the La content in the La-MCM-41 samples. On the contrary, Ce-MCM-41 catalysts showed low reactivity in the oxidation of styrene and the conversion of styrene decreased with the increase of the Ce content in the Ce-MCM-41 samples.

Leaching of styrene and other aromatic compounds in drinking water from PS bottles

Bottled water may not be safer, or healthier, than tap water. The present studies have proved that styrene and some other aromatic compounds leach continuously from polystyrene （PS） bottles used locally for packaging. Water sapmles in contact with PS were extracted by a preconcentration technique called as ＂purge and trap＂ and analysed by gas chromatograph-mass spectrometer （GC/MS）. Eleven aromatic compounds were identified in these studies. Maximum concentration of styrene in PS bottles was 29.5 μg/L. Apart from styrene, ethyl benzene, toluene and benzene were also quantified but their concentrations were much less than WHO guide line values. All other compounds were in traces. Quality of plastic and storage time were the major factor in leaching of styrene. Concentration of styrene was increased to 69.53 μg/L after one-year storage. In Styrofoam and PS cups studies, hot water was found to be contaminated with styrene and other aromatic compounds. It was observed that temperature played a major role in the leaching of styrene monomer from Styrofoam cups. Paper cups were found to be safe for hot drinks.

Synthesis of HTLcs modified by K_(3)PO_(4) for side chain alkylation of toluene with methanol

A series of calcined HTLcs catalysts were prepared and modified with potassium phosphate by impregnation method to clarify the influence of catalyst alkalinity on the side chain alkylation of toluene with methanol for synthesis of ethylbenzene and styrene.The catalysts were characterized by X-ray diffraction(XRD),N_(2)physical adsorption-desorption,Fourier-transform infrared spectroscopy(FT-IR),Scanning electron microscopy(SEM),X-ray photoelectron spectrometry(XPS),NH_(3)temperature-programmed desorption(NH_(3)-TPD)and CO_(2)temperature-programmed desorption(CO_(2)-TPD).It was found that the selectivity of styrene was highest(39.25%)when the K_(3)PO_(4)loading was 7.5 wt%.And the total yield of styrene and ethylbenzene could reach 65.08%with 10 wt%K_(3)PO_(4)loading.This might due to the fact that the addition of K_(3)PO_(4)could adjust the acid and basic sites of catalysts.In addition,appropriate strength and amount of basic sites were favorable to producing more styrene.

Studies on the Mechanism of the Direct Synthesis of Styrene form Benzene and Ethylene

The adsorption behavior and description behavior of benzene , ethylene and ethylbenzene over HZSM-5 and Co/HZSM-5 catalysts were studied by means of TPSR (Temperature programmed surface reaction) technique. TPSR results of ben- zene and ethylene co-adsorption show that the maian products are styrene , ethylben- zene, toluene, propane, and butane. In a separate experiment of ethylbenzene ad- sorption, styrene . toluene and benzene are formed due to cracking and dehydro- genation. The mechanism of styrene formation was proposed , i. e. , the reaction was carried out via. the dehydrogenation of mediate species ethylbenzene according to the results of TPSR-MS , activity testing and thermodynamic analysis.

Photoreductive degradation of sulfur hexafluoride in the presence of styrene

Sulfur hexafluoride （SF6） is known as one of the most powerful greenhouse gases in the atmosphere. Reductive photodegradation of SF6 by styrene has been studied with the purpose of developing a novel remediation for sulfur hexafluoride pollution. Effects of reaction conditions on the destruction and removal efficiency （DRE） of SF6 are examined in this study. Both initial styrene-to-SF6 ratio and initial oxygen concentration exert a significant influence on DRE. SF6 removal efficiency reaches a maximum value at the initial styrene-to-SF6 ratio of 0.2. It is found that DRE increases with oxygen concentration over the range of 0 to 0.09 mol/m^3 and then decreases with increasing oxygen concentration. When water vapor is fed into the gas mixture, DRE is slightly enhanced over the whole studied time scale. The X-ray Photoelectron Spectroscopy （XPS） analysis, together with gas chromatography-mass spectrometry （GC-MS） and Fourier Transform Infrared spectroscopy （FT-IR） analysis, prove that nearly all the initial fluorine residing in the gas phase is in the form of SiF4, whereas, the initial sulfur is deposited in the form of elemental sulfur, after photodegradation. Free from toxic byproducts, photodegradation in the presence of styrene may serve as a promising technique for SF6 abatement.

Theoretical and Experimental Study on Reaction Coupling: Dehydrogenation of Ethylbenzene in the Presence of Carbon Dioxide

Dehydrogenation of ethylbenzene （EB） to styrene （ST） in the presence of CO2, in which EB dehydrogenation is coupled with the reverse water-gas shift （RWGS）, was investigated extensively through both theoretical analysis and experimental characterization. The reaction coupling proved to be superior to the single dehydrogenation in several respects. Thermodynamic analysis suggests that equilibrium conversion of EB can be improved greatly by reaction coupling due to the simultaneous elimination of the hydrogen produced from dehydrogenation. Catalytic tests proved that iron and vanadium supported on activated carbon or Al2O3 with certain promoters are potential catalysts for this coupling process. The catalysts of iron and vanadium are different in the reaction mechanism, although ST yield is always associated with CO2 conversion over various catalysts. The two-step pathway plays an important role in the coupling process over Fe/Al2O3, while the one-step pathway dominates the reaction over V/Al2O3. Coke deposition and deep reduction of active components are the major causes of catalyst deactivation. CO2 can alleviate the catalyst deactivation effectively through preserving the active species at high valence in the coupling process, though it can not suppress the coke deposition.

Synthesis of curcuminoid-imprinted polymers applied to the solidphase extraction of curcuminoids from turmeric samples

A molecular imprinting polymer technique was successfully applied to precipitation polymerization by using styrene as a functional monomer, curcuminoids as templates, acetonitrile as a porogenic solvent,benzoyl peroxide as the initiator, and ethylene glycol dimethacrylate as the crosslinker. The effects of interaction on the adsorption capacity of the molecularly imprinted polymer(MIP) and non-imprinted polymer(NIP) were investigated. A comparison of the adsorption capacity for MIP and NIP indicated that the NIP had the lowest adsorption capacity. The curcuminoid-imprinted polymer(Cur-MIP) was synthesized from 0.0237 mmol of styrene, 47.0 g of acetonitrile, 1.0238 mmol of ethylene glycol dimethacrylate, 0.0325 mmol of curcuminoids, and 0.2480 mmol of benzoyl peroxide. A high-performance liquid chromatography method with fluorescence detection was developed and validated for various chromatographic conditions for the determination of the curcuminoids in turmeric samples. The sample solution was separated using the Cur-MIP via solid-phase extraction and analyzed on a Brownlee analytical C_(18) column(150 mm ×6 mm, 5 mm) using an isocratic elution consisting of acetonitrile and 0.1%trichloroacetic acid(40:60, v/v). The flow rate was maintained at 1.5 m L/min. The fluorescence detector was set to monitor at λex? 426 nm and λem? 539 nm. The quantification limit values were found to be16.66, 66.66, and 33.33 mg/L for curcumin, demethoxycurcumin, and bisdemethoxycurcumin, respectively. Thus, we concluded that the Cur-MIP and high-performance liquid chromatographic-fluorescence method could be applied to selective extraction and could be used as a rapid tool for the determination of curcuminoids in medicinal herbal extracts.

MONOMER REACTIVITY RATIO AND THERMAL PERFORMANCE OFα-METHYL STYRENE AND GLYCIDYL METHACRYLATE COPOLYMERS

Synthesis and characterization of the copolymers （PAG） of α-methyl styrene （AMS） and glycidyl methacrylate （GMA） are presented. The copolymers of PAG were characterized by gel permeation chromatography （GPC）, Fourier transform infrared spectroscopy （FTIR）, nuclear magnetic resonance （^1H-NMR） and thermogravimetery （TG）. Based on the copolymer compositions determined by ^1H-NMR, the reactivity ratios of AMS and GMA were found to be 0.105 ± 0.012 and 0.883 ± 0.046 respectively by Kelen-Tudos method. TG revealed that thermal stability of the copolymers decreased with increasing the AMS content in the copolymers, which indicated that the degradation was mainly caused by the chain scission of AMS-containing structures. Under heating, the copolymers depolymerize at their weak bonds and form chain radicals, which could further initiate other chemical reactions.

Alumina-boron catalysts for oxidative dehydrogenation of ethylbenzene to styrene: Influence of alumina-boron composition and method of preparation on catalysts properties

Different mole ratio Al-B catalysts (Al-10B to Al-35B) were synthesized by using sol-gel (SG) method. Ethyl benzene (EB) dehydrogenation in the presence of oxygen and water steam was carried out on these catalysts at 450–500℃ with EB contact time of 0.54 gcat.s.cm^–3. Acidity of Al-B catalysts was estimated by using NH3-TPD-mass spectral analysis studies. SEM-mapping images revealed fine distribution of boron up to 15% of its loading in alumina (Al-15B), whereas, boron aggregation was observed in higher boron content (Al-25B and Al-35B) catalysts. Essentially, acid sites of very weak strength (Tmax ≤ 125℃) were observed for Al and Al-10B catalysts and resulted in low EB conversion and styrene yield. On the other hand, acid sites of weak strength (Tmax ≤ 180℃) were observed for Al-25B and Al-35B catalysts and resulted in high EB conversion. However, greater styrene yield (43.2%) with reasonable EB conversion (46%) was obtained on acid sites of weak moderate strength in Al-15B catalyst. Further, Al-15B catalyst was synthesized by using co-precipitation (COP) and impregnation (IMP) methods. Acid sites related to NOx formation during the NH3-TPD-mass analysis on IMP and COP catalyst essentially improved the EB conversion to 66% and 63% respectively at 500℃. However, these acid sites were diminished in Al-B SG catalyst and resulted in 50% of EB conversion at 500 ℃. At 50% of EB conversion level, styrene selectivity of 73%, 82.5% and 84% were observed on Al-B IMP, Al-B COP and Al-SG catalysts, respectively. Hence, different method of preparation of Al-B catalyst generated acid sites of different strength and density and thereby influenced the styrene formation.

CATALYTIC COPOLYMERIZATION OF STYRENE AND ETHYLENE BY NEUTRAL NICKEL(Ⅱ) COMPLEXES IN EMULSION

Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were characterized by an array of techniques including NMR,GPC,TEM,WAXD and DSC.The results indicate that the copolymers obtained are mostly block copolymers of polyethylene with random insertion of styrene units,and their M_W is in the range of 10~5-10~6.By enhancing the electron withdrawing of the s...

Copolymerization of Styrene with N-phenylmaleimide by Rare Earth Coordination Catalysts

Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an alternating structure.

Dynamic Supercritical Fluid Devolatilization of Polymers

A number of studies have been reported on the applications of supercritical fluids to polymeric processes. The presence of volatiles can affect the end-use properties of polymer materials. Therefore, these volatiles must be reduced to a level below the maximum permissible limit. Conventional heat-relevant techniques for polymer devolatilization sometimes have limited effectiveness. Devolatilization with supercritical fluids, however, can enhance removal of volatiles from polymers. A model for diffusion-limited extraction is used to characterize dynamic supercritical fluid devolatilization of spherical polymer particles. The rate of supercritical fluid devolailization for styrene/polystyrene system is measured at 343 K and 18 MPa and at CO2 flow rate of 1.93, 3.27 and 5.62 L·min^-1, respectively. The model analysis, which is consistent with experimental results, indicates that the supercritical fluid devolatilization is not solubility-limited but diffusion-limited when CO2 flow rate is above 4.00 L·min^-1.