Exploring the relationship between ambient sulfur dioxide and semen quality parameters:A systematic review and meta-analysis

Objective:To investigate the relationship between ambient sulfur dioxide(SO2)exposure and semen quality parameters.Methods:A systematic literature search was conducted to identify relevant studies investigating the association between SO2 exposure and semen quality parameters.This search encompassed the timeframe from January 2000 to May 2023 and included electronic databases such as Web of Science,Google Scholar,PubMed,Cochrane,and Scopus.Pooled effect estimates with 95%confidence intervals(CI)were calculated using percent changes(PC).The meta-analysis included seven studies with 6711 participants and 15087 semen samples.Results:The results revealed a significant negative association between ambient SO2 exposure and certain semen quality parameters.In particular,SO2 exposure was associated with a significant decrease in progressive motility(PC=0.032;95%CI:-0.063 to-0.001;P=0.044)and sperm concentration(PC=-0.020;95%CI:-0.036 to-0.005;P=0.012).However,no statistically significant associations were observed for total sperm count(PC=-0.038;95%CI:-0.079 to 0.003;P=0.070),seminal fluid volume(PC=-0.009;95%CI:-0.048 to-0.030;P=0.662)and sperm motility(PC=-0.17;95%CI:-0.363 to 0.022;P=0.830).In addition,the results of the subgroup analysis revealed specific variables that were associated with the decrease in relevant sperm parameters.Conclusions:This systematic review and meta-analysis provides compelling evidence supporting a consistent negative association between exposure to ambient SO2 and semen quality parameters.

Copper slag assisted coke reduction of phosphogypsum for sulphur dioxide preparation

The reduction of phosphogypsum(PG)to lime slag and SO_(2)using coke can effectively alleviate the environmental problems caused by PG.However,the PG decomposition temperature remains high and the product yield remains poor.By adding additives,the decomposition temperature can be further reduced and PG decomposition rate and product yield can be improved.However,the use of current additives such as Fe_(2)O_(3)and SiO_(2)brings the problem of increasing economic cost.Therefore,it is proposed to use solid waste copper slag(CS)as a new additive to reduce PG to prepare SO2,which can reduce the cost and meet the environmental benefits at the same time.The effects of proportion,temperature and thermostatic time on PG decomposition are investigated by experimental and kinetic analysis combined with FactSage thermodynamic calculations to optimize the roasting conditions.Finally,the reaction mechanism is proposed.It is found that adding CS to the coke and PG system can increase the rate of PG decomposition and SO_(2)yield while lowering the PG decomposition temperature.For example,when the CS/PG mass ratio increases from 0 to 1,PG decomposition rate increases from 83.38%to 99.35%,SO_(2)yield increases from 78.62%to 96.81%,and PG decomposition temperature decreases from 992.4℃to 949.6℃.The optimal reaction parameters are CS/PG mass ratio of 1,Coke/PG mass ratio of 0.06 at 1100℃for 20 min with 99.35%PG decomposition rate and 96.81%SO_(2) yield.The process proceeds according to the following reactions:2CaSO_(4)+ 0.7C + 0.8Fe_(2)SiO_(4)→0.8Ca_(2)SiO_(4)+ 0.2Ca_(2)Fe_(2)O_(5)+ 0.4Fe_(3)O_(4)+2SO_(2)+ 0.7CO_(2)Finally,a process for decomposing PG with coke and CS is proposed.

Fine quantitative characterization of high-H2S gas reservoirs under the influence of liquid sulfur deposition and adsorption

In order to clarify the influence of liquid sulfur deposition and adsorption to high-H2S gas reservoirs,three types of natural cores with typical carbonate pore structures were selected for high-temperature and high-pressure core displacement experiments.Fine quantitative characterization of the cores in three steady states(original,after sulfur injection,and after gas flooding)was carried out using the nuclear magnetic resonance(NMR)transverse relaxation time spectrum and imaging,X-ray computer tomography(CT)of full-diameter cores,basic physical property testing,and field emission scanning electron microscopy imaging.The loss of pore volume caused by sulfur deposition and adsorption mainly comes from the medium and large pores with sizes bigger than 1000μm.Liquid sulfur has a stronger adsorption and deposition ability in smaller pore spaces,and causes greater damage to reservoirs with poor original pore structures.The pore structure of the three types of carbonate reservoirs shows multiple fractal characteristics.The worse the pore structure,the greater the change of internal pore distribution caused by liquid sulfur deposition and adsorption,and the stronger the heterogeneity.Liquid sulfur deposition and adsorption change the pore size distribution,pore connectivity,and heterogeneity of the rock,which further changes the physical properties of the reservoir.After sulfur injection and gas flooding,the permeability of TypeⅠreservoirs with good physical properties decreased by 16%,and that of TypesⅡandⅢreservoirs with poor physical properties decreased by 90%or more,suggesting an extremely high damage.This indicates that the worse the initial physical properties,the greater the damage of liquid sulfur deposition and adsorption.Liquid sulfur is adsorbed and deposited in different types of pore space in the forms of flocculence,cobweb,or retinitis,causing different changes in the pore structure and physical property of the reservoir.

Effects of zinc on χ-Fe_(5)C_(2) for carbon dioxide hydrogenation to olefins:Insights from experimental and density function theory calculations

Production of light olefins from CO_(2), the primary greenhouse gases, is of great importance to mitigate the adverse effects of CO_(2) emission on environment and to supply the value-added products from nonpetroleum resource. However, development of robust catalyst with controllable selectivity and stability remains a challenge. Herein, we report that Zn-promoted Fe catalyst can boost the stable and selective production of light olefins from CO_(2). Specifically, the Zn-promoted Fe exhibits a highly stable activity and olefin selectivity over 200 h time-on-stream compared to the unpromoted Fe catalyst, primarily owing to the preservation of active χ-Fe_(5)C_(2) phase. Structural characterizations of the spent catalysts suggest that Zn substantially regulates the content of iron carbide on the surface and suppresses the reoxidation of bulk iron carbide during the reaction. DFT calculations confirm that adsorption of surface carbon atoms and graphene-like carbonaceous species are not thermochemically favored on Zn-promoted Fe catalyst. Carbon deposition by CAC coupling reactions of two surface carbon atoms and dehydrogenation of CH intermediate are also inhibited. Furthermore, the effects of Zn on antioxidation of iron carbide were also investigated. Zn favored the hydrogenation of surface adsorbed oxygen atoms to H_(2)O and the desorption of H_(2)O, which reduces the possibility of surface carbide being oxidized by the chemisorbed oxygen.

Effects of Selenium Dioxide on Apoptosis, Bcl-2 and P53 Expression, Intracellular Reactive Oxygen Species and Calcium Level in Three Human Lung Cancer Cell Lines

To evaluate the anti-tumor effects of SeO2 and its mechanisms on three human lung cancer cell lines. Methods: Three lung cancer cells A549, GLC-82 and PG were treated with 3-30 μmol/L SeO2. Flow cytometry was used to detect apoptosis, and analyze the changes of expression of p53 and Bcl-2, as well as ROS and Ca^2+ level within cells. Results:SeO2 markedly inhibited cell proliferation and viability, and prompted apoptosis after 48 h treatment. SeO2 at 10 μmol/L induced 47.8% apoptosis in A549 cells, 40.8% in GLC-82 cells, 18.2% in PG cells. SeO2 at 30 μmol/L induced 37.8% apoposis in PG cells,but did not increase apoptotic raes in other two cells. SeO2 could down-regulate the mean fluorescent intensity of Bcl-2 from 65.8 to 9.6 in A549, but not in GLC-82 and in PG, cells, up-regulate wild type p53 level in all three cells. SeO2 decreased the ROS and Ca^2+ level markedly within three tested cells. Conclusion: SeO2 showed anti-tumor effect via apoptosis pathway in three lung cancer cell lines. The decrease of ROS and Ca^2+ level within cells as well as regulation of Bcl-2 and p53 expression may play important roles in above apoptotic procedure.

共沉淀法和浸渍法制备的HoCeMn/TiO_(2)催化剂的脱硝性能

采用浸渍法和共沉淀法制备了HoCeMn/TiO_(2)脱硝催化剂并对其结构和性能进行了表征。结果表明共沉淀法增强了活性组分和载体的相互作用,从而增加了HoCeMnTi-C催化剂表面Ce^(3+)、Mn^(4+)以及吸附氧的含量,使其表现出优异的低温氧化还原性能。此外,共沉淀法制备的HoCeMnTi-C具有更多的表面酸性位点及更强的表面酸性。催化剂表面酸性和氧化还原性能的提高有助于氨的吸附和活化,从而显著提高其活性。表面酸性位点的增多还抑制了H_(2)O和SO_(2)在催化剂表面的吸附,提升了催化剂的抗水抗硫性能。催化剂上的选择性催化还原(SCR)反应遵循Eley-Rideal(E-R)机制,催化剂硫中毒是源于形成的硫酸盐覆盖或破坏了催化剂活性位。

Regeneration of 2-amino-2-methyl-1-propanol used for carbon dioxide absorption

To improve the efficiency of the carbon dioxide cycling process and to reduce the regeneration energy consumption, a sterically hindered amine of 2-amino-2-methyl-1- propranol （AMP） was investigated to determine its regeneration behavior as a CO2 absorbent. The CO2 absorption and amine regeneration characteristics were experimentally examined under various operating conditions. The regeneration efficiency increased from 86.2% to 98.3% during the temperature range of 358 to 403 K. The most suitable regeneration temperature for AMP was 383 K, in this experiment condition, and the regeneration efficiency of absorption/regeneration runs descended from 98.3% to 94.0%. A number of heat-stable salts （HSS） could cause a reduction in CO2 absorption capacity and regeneration efficiency. The results indicated that aqueous AMP was easier to regenerate with less loss of absorption capacity than other amines, such as, monoethanolamine （MEA）, diethanolamine （DEA）, diethylenetriamine （DETA）, and N-methyldiethanolamine （MDEA）.

750℃高温CO_(2)掺杂SO_(2)环境中Super304H及Inconel625的腐蚀行为

研究掺杂气体对合金的腐蚀行为及作用机理对超临界二氧化碳(supercritical carbon dioxide,S-CO_(2))发电技术具有重要意义。该文开展Super304H及Inconel625合金的高温CO_(2)腐蚀试验,并结合腐蚀增重法、扫描电镜观察及XRD分析,研究两种耐热合金在750℃CO_(2)及掺杂SO_(2)环境中的腐蚀行为。结果表明,两种合金在750℃CO_(2)、750℃CO_(2)+SO_(2)环境中的腐蚀动力学均遵循抛物线规律,Inconel625抗腐蚀能力优于Super304H,具有较少的腐蚀增重;Super304H在750℃CO_(2)腐蚀初期增重高于CO_(2)+SO_(2)环境,而120 h后在CO_(2)+SO_(2)环境中腐蚀增重较高。两种环境中腐蚀500 h后,Super304H表面氧化膜为单层Cr_(2)O_(3)及外层疏松瘤状富铁氧化物与内氧化物FeCr_(2)O_(4)组成的局部双层氧化膜;Inconel625为单层均匀致密Cr_(2)O_(3)氧化膜,平均厚度不到1μm。高温CO_(2)腐蚀环境中,Cr含量对提高合金抗腐蚀性能具有至关重要的作用。高温CO_(2)掺杂SO_(2)对于Cr_(2)O_(3)形成合金具有抑制渗碳的作用,对于氧化铁形成合金具有加速腐蚀及渗碳作用。

Control strategy for sulfur dioxide and acid rain pollution in China

Several factors, namely, coal dominated primary energy mix, extensive economic development mode, inefficient energy utilization, and the imperfect environmental regulations, result in the serious urban sulfur dioxide pollution and large scale sulfate type acid precipitation in China. In 1995, China′s sulfur dioxide emissions reached 23.70 Mt, and the areas affected by acid rain accounted for 40% of the territory. Chinese government accords considerable importance to the sulfur dioxide and acid rain contamination. New sets of environmental friendly policies have been promulgated. But enforcement of laws and regulations on SO 2 emissions need to be further improved and broadened, especially those respond to market conditions. This paper focuses particular attention on the analysis of strategy, policies, and national actions which had or should be taken against sulfur dioxide emissions nationwide to achieve the environmental targets, on the basis of which gives the technical options in future.

Defect engineering of high-loading single-atom catalysts for electrochemical carbon dioxide reduction

Electrochemical carbon dioxide reduction reaction(CO_(2)RR)provides an attractive approach to carbon capture and utilization for the production high-value-added products.However,CO_(2)RR still suffers from poor selectivity and low current density due to its sluggish kinetics and multitudinous reaction pathways.Single-atom catalysts(SACs)demonstrate outstanding activity,excellent selectivity,and remarkable atom utilization efficiency,which give impetus to the search for electrocatalytic processes aiming at high selectivity.There appears significant activity in the development of efficient SACs for CO_(2)RR,while the density of the atomic sites remains a considerable barrier to be overcome.To construct high-metal-loading SACs,aggregation must be prevented,and thus novel strategies are required.The key to creating high-density atomically dispersed sites is designing enough anchoring sites,normally defects,to stabilize the highly mobile separated metal atoms.In this review,we summarized the advances in developing high-loading SACs through defect engineering,with a focus on the synthesis strategies to achieve high atomic site loading.Finally,the future opportunities and challenges for CO_(2)RR in the area of high-loading single-atom electrocatalysts are also discussed.

Mechanism explanation for SO_2 oxidation rate of Cs-Rb-V series sulfuric acid catalyst at low temperature

The reaction kinetics of SO 2 oxidation on Cs Rb V series sulfuric acid catalyst promoted by alkali salts such as cesium and rubidium was studied. A three step reaction mechanism of SO 2 oxidation was proposed, in which it was assumed that oxidation of quadrivalent vanadium complex was a controlling step. Then, a mechanism model equation was concluded according to the three step reaction mechanism. The SO 2 oxidation rate was measured with a non gradient reactor under the conditions of temperature of 380～520?℃ and space velocity of 3?600～7?200?h -1 . Through calculating with Powell nonlinear regression method, the parameters of model equation were obtained: K 1=0.152?exp(-62?073/ (RT) ), K 2=8.18?exp(-2?384/ (RT) ), K 3=0.221?exp(-18?949/ (RT) ). It was found that the model equation could fit with all the experimental reaction rate data very well. [

Atmospheric Corrosion of Steel A3 Deposited with Ammonium Sulfate and in the Presence of Sulfur Dioxide

A laboratory study of the atmospheric corrosion of carbon steel deposited with (NH4)2SO4 in the presence of SO2 is reported. The different levels of (NH4)2SO4 (0, 15, 30, 45, 60 μg·cm-2) were added on the surface of the samples before the exposure. The corrosion was investigated by a combination of gravimetry, Fourier transform infrared spectroscope and scanning electron microscopy. A detailed knowledge about the corrosion products was acquired, both quantitatively and qualitatively. The results show that the metal loss increased and the increasing tendency of corrosion rates slowed down with the increasing exposure time. The phase constituents of the corrosion products are mainly α-FeO(OH), γ-FeO(OH), and δ-FeO(OH).

Photochemical reaction of magnesium tetraphenyl porphyrin with sulfur dioxide

The photochemical reaction of magnesium tetraphenyl porphyrin（MgTPP） with sulfur dioxide（SO_2） was investigated in dichloromethane（CH_2Cl_2） by steady-state fluorescence,UV-vis absorption,MS,and XRD spectroscopic techniques.These spectra showed that under irradiation MgTPP reacted with SO_2 to form 1：1 molecular adduct at first step.During the process of keeping irradiation and maintaining the flow of SO_2,SO_2 was reduced into S^（2-） by MgTPP and the results were detected using MS and XRD techniques.Understanding the photochemical reaction of MgTPP with SO_2 is of key interest in elucidating fundamental photochemical reaction mechanisms associated with this class of chlorophyll in the presence of SO_2.

CeO_(2)改性CuO纳米棒协同促进电催化还原CO_(2)制乙烯

随着社会经济发展及人类活动扩大,大气中CO_(2)的浓度日益增加,且带来诸多环境污染问题.因此开发高效、可持续的CO_(2)转化方法至关重要.本文基于电催化反应机理,制备了一系列CuO/CeO_(2)纳米棒复合材料,以促进二氧化碳高选择性还原为C2H_(4).结果表明,经过优化后的CuO/CeO_(2)-2(molCeO_(2):mol_(CuO)=2%)电催化剂在电流密度达到20mA/cm^(2)时,所需电位最低(-0.99V vs.RHE),且对乙烯具有最高的选择性,在电压为-1.08V vs.RHE时,法拉第效率高达46%.此优势可能与大的表面积、更粗糙的表面以及CuO和CeO_(2)之间的协同效应有关,有效提高了反应活性位点和电子转移效率.本研究将为设计和优化CuO基复合材料以实现CO_(2)的高效转化提供理论指导.

Photocatalytic reduction of carbon dioxide to methanol by Cu_2O/SiC nanocrystallite under visible light irradiation

The Cu2O/SiC photocatalyst was obtained from SiC nanoparticles （NPs） modified by Cu2O. Their photocatalytic activities for reducing CO2 to CH3OH under visible light irradiation have been investigated. The results indicated that besides a small quantity of 6H-SiC, SiC NPs mainly consisted of 3C-SiC. The band gaps of SiC and Cu2O were estimated to be about 1.95 and 2.23 eV from UV-Vis spectra, respectively. The Cu2O modification can enhance the photocatalytic performance of SiC NPs, and the largest yields of methanol on SiC, Cu2O and Cu2O/SiC photocatalysts under visible light irradiation were 153, 104 and 191μmol/g, respectively.

Sulfur dioxide-hydrogen peroxide relationships and acidification of precipitation in Guiyang area-a case study

-The concentrations of gas phase SO2, O3 and chemical composition of sequential rainwater samples were measured on 6/11/88 to 6/28/88 at some sites of Guiyang area. S (IV) was present in great excess of H2O2 in rainwater samples collected at residential sites of the city corresponding to high level of gas phase SO2. Considerable H2O2 in rainwater samples was observed in background air at suburbs. The evidence that clean rainwater samples were collected at 20km away from the city in 6/18/88 precipitation event revealed that the major process of acidification of the rain in the high polluted areas was below-cloud scavenging of trace gases. From a simulation calculation it was found that the rate of oxidation of S(IV) by O3 and by Mn2+, Fe3+ catalytic in high pH rainwater is significant, but for low pH the major SO42- is produced by the reaction of S (IV) with H2O2.

Surface Acidity/Basicity and Catalytic Reactivity of CeO2/7-Al2O3 Catalysts for the Oxidative Dehydrogenation of Ethane with Carbon Dioxide to Ethylene

Dehydrogenation of ethane to ethylene in CO_2 was investigated overCeO_2/γ-Al_2O_3 catalysts at 700℃ in a conventional flow reactor operating at atmosphericpressure. XRD, BET and microcalori-metric adsorption techniques were used to characterize thestructure and surface acidity/basicity of the CeO_2/γ-Al_2O_3 catalysts. The results show that thesurface acidity decreased while the surface basicity increased after the addition of CeO_2 toγ-Al_2O_3. Accordingly, the activity of the hydrogenation reaction of CO_2 increased, which mightbe responsible for the enhanced conversion in the dehydrogenation of ethane to ethylene. The highestethane conversion obtained was about 15% for the 25%CeO_2/γ-Al_2O_3. The selectivity to ethylenewas high for all the CeO_2, γ-Al_2O_3 and CeO2/γ-Al_2O_3 catalysts.

硫缺陷型In_(2)S_(3)光催化剂高效分解水制氢研究

缺陷工程被认为是提高光催化剂分解水制氢性能的关键策略之一,然而有关缺陷诱导半导体材料电子结构演变并增强光生载流子传输机制尚不明确.我们通过简单的一步水热合成法成功构建了富含S缺陷的In_(2)S_(3)半导体光催化剂(V_(S)-In_(2)S_(3)),在模拟太阳光辐照下其光催化分解水产氢性能相比传统的In_(2)S_(3)(P-In_(2)S_(3))提升了近一个数量级(达到221.18μmol∙g^(−1)∙h^(−1)).此外,利用自主研发的原位X射线光电子能谱(SI-XPS)结合相关密度泛函理论计算证实:S缺陷可诱导强还原性的低价态In(In^((3−x)+))暴露,进而增强In位点对H_(2)O的吸附和活化能力,因此,S缺陷型In_(2)S_(3)表现出显著增强的光催化析氢活性.此外,可视化观测到H_(2)分子在原位光照下脱质子转化为OH的分解水制氢过程.该研究为缺陷型光催化剂设计及光催化分解水反应机制和过程研究提供了一定的见解.

Morphology Controlling of the Ultrafine Cerium Dioxide (CeO_2) Precursor

The synthesis of ultrafine cerium dioxide precursor via homogeneous precipitation was studied. Mixed aqueous solution of anhydrous cerium nitrate and urea was first heated to 85℃ for 2 h, and the prepared suspension was then aged at room temperature for various periods of time. White precipitate was finally collected by centrifuging and washed with distilled water and anhydrous ethanol. The obtained cerium dioxide (CeO2) precursor was observed with SEM. It was found that the morphology and size of the precursor were strongly affected by aging time and stirring conditions (with or without stirring). The precipitated fine spherical particles of the precursor changed their shape from ellipse to slice or directly to slice. Fine spherical monodispersed (300 nm) precursor powders could be obtained by controlling the aging time. Stirring the solution also could change the reaction process and thus the morphology and size of the precursor were changed.