Based on screening analysis, laser size analysis, grindability and rigidity tests of samples collected on line from a cement and a power plant, a simulation of the grinding process in vertical roller mills was carried...Based on screening analysis, laser size analysis, grindability and rigidity tests of samples collected on line from a cement and a power plant, a simulation of the grinding process in vertical roller mills was carried out. The simulation calculation used a breakage function, B. The results indicate that the breakage function, B, and the selection function, S, in the form of a matrix, can be used to express the probability of the material breaking during the grinding process. This allows the size distribution of the product to be numerically estimated. The simulation results also show that the simulated size distribution curves fit the actual experimental product curves quite well. The model provides a good starting point for simulation of the grinding process. Further research is needed to determine the proper breakage function and the matrix value of the selection function.展开更多
We investigated whether the vertical roller mill can be efficiently used in the beneficiation of low-grade magnesite and whether it can improve upon the separation indices achieved by the ball mill.We conducted experi...We investigated whether the vertical roller mill can be efficiently used in the beneficiation of low-grade magnesite and whether it can improve upon the separation indices achieved by the ball mill.We conducted experiments involving the reverse flotation and positive flotation of low-grade magnesite to determine the optimum process parameters,and then performed closed-circuit beneficiation experiments using the vertical roller mill and ball mill.The results show that the optimum process parameters for the vertical roller mill are as follows:a grinding fineness of 81.6wt%of particles less than 0.074 mm,a dodecyl amine(DDA)dosage in magnesite reverse flotation of 100 g·t?1,and dosages of Na2CO3,(NaPO3)6,and NaOL in the positive flotation section of 1000,100,and 1000 g·t?1,respectively.Compared with the ball mill,the use of the vertical roller mill in the beneficiation of low-grade magnesite resulted in a 1.28%increase in the concentrate grade of MgO and a 5.88%increase in the recovery of MgO.The results of our causation mechanism analysis show that a higher specific surface area and greater surface roughness are the main reasons for the better flotation performance of particles ground by the vertical roller mill in the beneficiation of lowgrade magnesite.展开更多
基金Project PBK2005022 supported by the Natural Science Foundation of Jiangsu Province
文摘Based on screening analysis, laser size analysis, grindability and rigidity tests of samples collected on line from a cement and a power plant, a simulation of the grinding process in vertical roller mills was carried out. The simulation calculation used a breakage function, B. The results indicate that the breakage function, B, and the selection function, S, in the form of a matrix, can be used to express the probability of the material breaking during the grinding process. This allows the size distribution of the product to be numerically estimated. The simulation results also show that the simulated size distribution curves fit the actual experimental product curves quite well. The model provides a good starting point for simulation of the grinding process. Further research is needed to determine the proper breakage function and the matrix value of the selection function.
基金the National Natural Science Foundation of China(Nos.51874072 and 51804200)the State Key Laboratory of Mineral Processing(No.BGRIMM-KJSKL-2017-02).
文摘We investigated whether the vertical roller mill can be efficiently used in the beneficiation of low-grade magnesite and whether it can improve upon the separation indices achieved by the ball mill.We conducted experiments involving the reverse flotation and positive flotation of low-grade magnesite to determine the optimum process parameters,and then performed closed-circuit beneficiation experiments using the vertical roller mill and ball mill.The results show that the optimum process parameters for the vertical roller mill are as follows:a grinding fineness of 81.6wt%of particles less than 0.074 mm,a dodecyl amine(DDA)dosage in magnesite reverse flotation of 100 g·t?1,and dosages of Na2CO3,(NaPO3)6,and NaOL in the positive flotation section of 1000,100,and 1000 g·t?1,respectively.Compared with the ball mill,the use of the vertical roller mill in the beneficiation of low-grade magnesite resulted in a 1.28%increase in the concentrate grade of MgO and a 5.88%increase in the recovery of MgO.The results of our causation mechanism analysis show that a higher specific surface area and greater surface roughness are the main reasons for the better flotation performance of particles ground by the vertical roller mill in the beneficiation of lowgrade magnesite.
