Roof collapse mechanism of weak surrounding rock for deep-buried tunnels under high geostress conditions

High geostress,a typical attribute of tunnels located at significant depths,is crucial in causing stress-induced failure and influencing the stability of the tunnel crown.This study developed an analytical method for the failure mechanism that occurs in deep-buried tunnel roofs,taking into account the influence of geostress.The limit analysis theory was utilized for deriving analytical solutions about the geometry of the collapsing surface and the limit supporting pressure.The collapsing surface obtained by the analytical solution was validated by the findings of the physical model test,which shows a high level of agreement with the actual one.An extensive investigation was done to explore the effects of the lateral pressure coefficients,the tunnel buried depth,the geological conditions of the surrounding rock,the long-short axis ratio,and the size of the tunnel profile.The findings indicate that an increase in the lateral pressure coefficient from 0.5 to 1.5 results in a reduction in the height of the collapsing zone by 2.08 m and the width of the collapsing zone by 1.15 m,while simultaneously increases the limit supporting pressure by 18.9%.The proposed upper bound method accurately determines the limit supporting pressure and the geometry of the collapsing surface,which aligns well with the results acquired through numerical modelling and on-site monitoring in actual engineering applications.The proposed analytical method can serve as a reference for similar crown failure issues of deep-buried tunnels.

Dissolution mechanism of a deep-buried sandstone reservoir in a deep water area:A case study from Baiyun Sag,Zhujiang River(Pearl River)Mouth Basin

Dissolution mechanism and favorable reservoir distribution prediction are the key problems restricting oil and gas exploration in deep-buried layers.In this paper,the Enping Formation and Zhuhai Formation in Baiyun Sag of South China Sea was taken as a target.Based on the thin section,scanning electron microscopy,X-ray diffraction,porosity/permeability measurement,and mercury injection,influencing factors of dissolution were examined,and a dissolution model was established.Further,high-quality reservoirs were predicted temporally and spatially.The results show that dissolved pores constituted the main space of the Paleogene sandstone reservoir.Dissolution primarily occurred in the coarse-and medium-grained sandstones in the subaerial and subaqueous distributary channels,while dissolution was limited in fine-grained sandstones and inequigranular sandstones.The main dissolved minerals were feldspar,tuffaceous matrix,and diagenetic cement.Kaolinization of feldspar and illitization of kaolinite are the main dissolution pathways,but they occur at various depths and temperatures with different geothermal gradients.Dissolution is controlled by four factors,in terms of depositional facies,source rock evolution,overpressure,and fault activities,which co-acted at the period of 23.8–13.8 Ma,and resulted into strong dissolution.Additionally,based on these factors,high-quality reservoirs of the Enping and Zhuhai formations are predicted in the northern slope,southwestern step zone,and Liuhua uplift in the Baiyun Sag.

Fisher discriminant analysis model and its application for prediction of classification of rockburst in deep-buried long tunnel

A Fisher discriminant analysis （FDA） model for the prediction of classification of rockburst in deep-buried long tunnel was established based on the Fisher discriminant theory and the actual characteristics of the project. First, the major factors of rockburst, such as the maximum tangential stress of the cavern wall σθ, uniaxial compressive strength σc, uniaxial tensile strength or, and the elastic energy index of rock Wet, were taken into account in the analysis. Three factors, Stress coefficient σθ/σc, rock brittleness coefficient σc/σt, and elastic energy index Wet, were defined as the criterion indices for rockburst prediction in the proposed model. After training and testing of 12 sets of measured data, the discriminant functions of FDA were solved, and the ratio of misdiscrimina- tion is zero. Moreover, the proposed model was used to predict rockbursts of Qinling tunnel along Xi＇an-Ankang railway. The results show that three forecast results are identical with the actual situation. Therefore, the prediction accuracy of the FDA model is acceptable.

Comparison of vibrations induced by excavation of deep-buried cavern and open pit with method of bench blasting

The measured data of vibrations induced by excavation of deep-buried cavern and open pit with method of bench blasting were analyzed by Fourier Transform and Wavelet Transform,and the characteristics of vibrations induced under these two circumstances were studied.It is concluded that with the similar rock condition and drilling-blasting parameters,vibration induced by bench blasting in deep-buried cavern has a higher main frequency and more scattered energy distribution than that in open pit.The vibration induced by bench blasting in open pit is mainly originated from the blast load,while the vibration induced by bench blasting in deep-buried cavern is the superposition of vibrations induced by blast load and transient release of in-situ stress.The vibration induced by transient release of in-situ stress increases with the stress level.

Mechanical Properties of Deep-buried Marble Material Under Loading and Unloading Tests

The mechanical properties are essentially different when rock material is subjected to loading or unloading conditions. In this study, loading and unloading tests with various confining pressures are conducted to investigate the mechanical properties of marble material samples taken from the deep diversion tunnels of Jinping II Hydropower Station. The stress-strain relationship, failure characteristics and strength criterion are compared and analyzed based on the experiment results. The results show： in the loading and unloading test, peak strength, lateral strain, axial strain and plastic deformation increase significantly as the confining pressure increases. Lateral strain increased significantly and obvious lateral dilatancy can be observed to the change of confining pressure; The fracture mode is mainly the single shear fracture for the triaxial compression test and post-peak test, angle between the failure surface and the ends of the rock material becomes smaller as the confining pressure increases. Hock-Brown strength criterion reflects the strength characteristics of marble material under two different unloading conditions, and has some supplementary effects to the rock material of mechanical field.

Numerical simulation of zonal disintegration of surrounding rock in the deep-buried chamber

Zonal disintegration is the phenomenon of cyclical rupture zone and nonrupture zone in the surrounding rock of a deep-buried chamber,which is different from that of a shallow chamber.Based on the finite difference software FLAC3D,the numerical simulation of surrounding rock with different mechanical parameters was conducted by using the SU model(Bilinear Strain-Softening Ubiquitous-Joint).The influences of buried depth,cohesion,and internal friction angle of surrounding rock on zonal disintegration were analyzed to reveal the influence law.The results show that:(1)after the chamber excavation,multiple rupture zones gradually extend from the chamber surface or adjacent periphery to the deep surrounding rock.In the extension process,a single rupture zone may be forked into two or even multiple rupture zones,which cross each other and form the zonal disintegration zone.(2)Zonal disintegration is affected by bothσ(in situ stress)and U_(cs)(uniaxial compression strength).Smaller U_(cs)and largerσwill lead to zonal disintegration.(3)The zoning fracture is not obvious in the case ofσ≤U_(cs).In the reverse case,zoning fracture appears remarkably in the surrounding rock around the chamber.These results reveal the influence law of zonal disintegration and provide theoretical support for the design of deep-buried chambers.

Analytical solution for steady seepage into a circular deep-buried mountain tunnel with grouted zone in anisotropic strata

Due to the existence of a large number of discontinuous fractures and interfaces in tunnel surrounding rocks,the groundwater inflow into tunnel generally presents significant anisotropy.Therefore,it is of great significance to consider the anisotropic permeability when dealing with water gushing-induced engineering accidents in water-rich mountain tunnels with large burial depth.In this study,based on the complex variable method and the seepage flow theory,a theoretical model of water inflow into a deep-buried circular tunnel in a fully saturated,anisotropic and semi-infinite aquifer is developed.The influence of grouted zone,initial support and secondary lining is fully considered.By comparison to the existing analytical methods and numerical results,the reliability of this proposed analytical solution is well validated.It is indicated from the parametric study that the groundwater inflow into tunnel presents an upward trend with an increasing value of the strata permeability in the vertical direction.Moreover,the water inflow rate and the total water head decrease with the growth of the thickness of grouting circle.It is suggested that reasonable grouting thickness and permeability should be controlled to enhance the grouting effect.This study provides a practical method for estimating the water inflow into a deep-buried,grouted and lined mountain tunnel considering the anisotropic strata permeability.

Experimental study on similarity materials for soft rock of deep-buried tunnels

When every parameter is properly scaled down in accordance with some similarity coefficients, it is possible to study the physical-mechanical properties of rock mass with a scale model. To identify the key mechanisms of soft rock in deep buried tunnels, the proper sand, binder and ratio were selected. During the process, the model manufacture technology was introduced and typical tests were done and the results were presented. The physical and meehanieal properties effects caused by each composition were discussed. It is shown that the physical and mechanical properties of chosen ratio material such as uniaxial compressive strength tests, elasticity modulus, tensile strength, internal frictional angle, and Poisson＇s ratio meet with similarity relationship well. The physical and mechanical properties of deep soft rock are simulated successfully.

Forecasting of water yield of deep-buried iron mine in Yanzhou, Shandong

This paper compares analytical and numerical methods by taking the forecasting of water yield of deep-buried iron mine in Yanzhou, Shandong as an example. Regarding the analytical method, the equation of infinite and bilateral water inflow boundary is used to forecast the water yield, and in the case of numerical simulation, we employed the GMS software to establish a model and further to forecast the water yield. On the one hand, through applying the analytical method, the maximum water yield of mine 1 500 m deep below the surface was calculated to be 13 645.17 m3/d; on the other hand, through adopting the numerical method, we obtained the predicted result of 3 816.16 m3/d. Meanwhile, by using the boundary generalization in the above-mentioned two methods, and through a comparative analysis of the actual hydro-geological conditions in this deep-buried mine, which also concerns the advantages and disadvantages of the two methods respectively, this paper draws the conclusion that the analytical method is only applicable in ideal conditions, but numerical method is eligible to be used in complex hydro-geological conditions. Therefore, it is more applicable to employ the numerical method to forecast water yield of deep-buried iron mine in Yanzhou, Shandong.

Stress wave propagation and incompatible deformation mechanisms in rock discontinuity interfaces in deep-buried tunnels

Complex weak structural planes and fault zones induce significant heterogeneity,discontinuity,and nonlinear characteristics of a rock mass.When an earthquake occurs,these characteristics lead to extremely complex seismic wave propagation and vibrational behaviors and thus pose a huge threat to the safety and stability of deep buried tunnels.To investigate the wave propagation in a rock mass with different structural planes and fault zones,this study first introduced the theory of elastic wave propagation and elastodynamic principles and used the Zoeppritz equation to describe wave field decomposition and develop a seismic wave response model accordingly.Then,a physical wave propagation model was constructed to investigate seismic waves passing through a fault,and dynamic damage was analyzed by using shaking table tests.Finally,stress wave attenuation and dynamic incompatible deformation mechanisms in a rock mass with fault zones were explored.The results indicate that under the action of weak structural planes,stress waves appear as a complex wave field decomposition phenomenon.When a stress wave spreads to a weak structural plane,its scattering may transform into a tensile wave,generating tensile stress and destabilizing the rock mass;wave dynamic energy is absorbed by a low-strength rock through wave scattering,which significantly weakens the seismic load.Wave propagation accelerates the initiation and expansion of internal defects in the rock mass and leads to a dynamic incompatible deformation.This is one of the main causes for large deformation and even instability within rock masses.These findings provide an important reference and guide with respect to stability analysis of rock mass with weak structural planes and fault zones.

Key Technologies for Design of Changqing Yellow River Super-long Bridge of Zhengzhou Ji'nan HSR

Changqing Yellow River Super-long Bridge of Zhengzhou-Ji'nan HSR is a partial cable-stayed bridge with concrete main girder and a unit length of 1,080 m.Studies are carried out on the key technologies of bridge design,and the main conclusions are as follows:The whole unit adopts the supporting system of tower pier consolidation and tower-beam separation,and each pier is provided with seismic mitigation and isolation bearing;shaped-steel reinforced concrete bridge tower is adopted to bring into full play the tensile performance of steel and the compressive performance of concrete,and avoid the construction challenges of setting up multi-layer and multi-stirrup reinforcement while improving the bearing capacity of section;a new type of double-side and bi-directional anti-skid anchorage device is adopted for the cable saddle of wire divider pipe in order to withstand the unbalanced cable force,and verify the reliability of the anti-skid anchorage device by solid model test;and large-segment cantilever pouring design is adopted for the main girder with a maximum segment length of 8 m to effectively shorten the construction period of the bridge.

Experimental study and numerical analysis on bearing behaviors of super-long rock-socketed bored pile groups

A centrifuge modeling test and a three-dimensional finite element analysis（FEA）of super-long rock-socketed bored pile groups of the Tianxingzhou Bridge are proposed.Based on the similarity theory,different prototypical materials are simulated using different indicators in the centrifuge model.The silver sand,the shaft and the pile cap are simulated according to the natural density,the compressive stiffness and the bending stiffness,respectively.The finite element method（FEM）is implemented and analyzed in ANSYS,in which the stress field during the undisturbed soil stage,the boring stage,the concrete-casting stage and the curing stage are discussed in detail.Comparisons in terms of load-settlement,shaft axial force distribution and lateral friction between the numerical results and the test data are carried out to investigate the bearing behaviors of super-long rock-socketed bored pile groups under loading and unloading conditions.Results show that there is a good agreement between the centrifuge modeling tests and the FEM.In addition,the load distribution at the pile top is complicated,which is related to the stiffness of the cap,the corresponding assumptions and the analysis method.The shaft axial force first increases slightly with depth then decreases sharply,and the rate of decrease in rock is greater than that in sand and soil.

The determination of sedimentary environment and associated energy in deep-buried marine carbonates:insights from natural gamma ray spectrometry log

It has always been challenging to determine the ancient sedimentary environment and associated energy in deep-buried marine carbonates.The energy represents the hydrodynamic conditions that existed when the carbonates were deposited.The energy includes light and chemical energies in compounds and kinetic energy in currents and mass flow.Deep-buried marine carbonates deposited during the Ordovician depositional period in the eastern Tarim Basin result from a complex interplay of tectonics,sedimentation,and diagenesis.As a result,determining the ancient sedimentary environment and associated energy is complex.The natural gamma-ray spectrometry(GRS)log(from 12 wells)is used in this paper to conduct studies on the sedimentary environment and associated energy in deep-buried marine carbonates.The findings show that the values of thorium(Th),uranium(U),potassium(K),and gamma-ray without uranium(KTh)in a natural GRS log can reveal lithological associations,mineral composition,diagenetic environment,stratigraphic water activity,and ancient climatic change.During the Ordovician,quantitative analysis and determination of sedimentary environment energy are carried out using a comprehensive calculation of natural GRS log parameters in typical wells(penetrating through the Ordovician with cores and thin sections)of well GC4,well GC6,well GC7,and well GC8.The results show that GRS log can determine different lithology associations in typical wells than a sieve residue log.Furthermore,cores and thin sections can be used to validate the determination of lithology associations.Based on the determination of lithology associations,the lithology associations that reflect the sedimentary environment and associated energy can be analyzed in a new approach.Furthermore,the sedimentary environment energy curve derived from a natural GRS log can reveal hydrodynamic fluctuations during depositional periods,which will aid in the discovery of carbonate reservoirs,establishing sequence stratigraphic frameworks,and the reconstruction of sea-level changes in the future.

Reversible Oxygen-Rich Functional Groups Grafted 3D Honeycomb-Like Carbon Anode for Super-Long Potassium Ion Batteries

Studies have found that oxygen-rich-containing functional groups in carbon-based materials can be used as active sites for the storage performance of K^(+),but the basic storage mechanism is still unclear.Herein,we construct and optimize 3D honeycomb-like carbon grafted with plentiful COOH/C=O functional groups(OFGC)as anodes for potassium ion batteries.The OFGC electrode with steady structure and rich functional groups can effectively contribute to the capacity enhancement and the formation of stable solid electrolyte interphase(SEI)film,achieving a high reversible capacity of 230 mAh g^(-1) at 3000 mA g^(-1) after 10,000 cycles(almost no capacity decay)and an ultra-long cycle time over 18 months at 100 mA g^(-1).The study results revealed the reversible storage mechanism between K^(+)and COOH/C=O functional groups by forming C-O-K compounds.Meanwhile,the in situ electrochemical impedance spectroscopy proved the highly reversible and rapid de/intercalation kinetics of K+in the OFGC electrode,and the growth process of SEI films.In particular,the full cells assembled by Prussian blue cathode exhibit a high energy density of 113 Wh kg^(-1) after 800 cycles(calculated by the total mass of anode and cathode),and get the light-emitting diodes lamp and ear thermometer running.

Axial bearing behavior of super-long piles in deep soft clay over stiff layers

In order to find out the bearing behavior of super-long piles located in deep soft clay over stiff layers around Dongting Lake, China, a test pile was first designed with the field loading test finished afterward. Based on the measured test results, load transfer mechanism and bearing behavior of the pile shaft were discussed in detail. Then, by introducing a bi-linear model for shaft friction and the tri-linear model for pile tip resistance, respectively, the governing differential equation of pile soil system was set up by the load transfer method with the analytical solutions derived as well, taking into account the effect by stratified feature and various bearing conditions of subsoil, material nonlinearity, and the sediment under pile tip. Furthermore, formulas to determine the axial capacity of super-long piles by the pile top settlement were advised and applied to analyze the test pile. Good agreement between the predicted load settlement variations and the measured data is obtained to verify the validity of the present method. The results also show that, the axial bearing capacity of super-long piles should be controlled by the allowable pile top settlement, and buckling stability of the pile shaft should be paid attention as well.

Realizing super-long Cu_2O nanowires arrays for high-efficient water splitting applications with a convenient approach

Nanowire(NW) structures is an alternative candidate for constructing the next generation photoelectrochemical water splitting system, due to the outstanding optical and electrical properties. NW photoelectrodes comparing to traditional semiconductor photoelectrodes shows the comparatively shorter transfer distance of photo-induced carriers and the increase amount of the surface reaction sites, which is beneficial for lowering the recombination probability of charge carriers and improving their photoelectrochemical(PEC) performances. Here, we demonstrate for the first time that super-long Cu_2O NWs, more than 4.5 μm,with highly efficient water splitting performance, were synthesized using a cost-effective anodic alumina oxide(AAO) template method. In comparison with the photocathode with planar Cu_2O films, the photocathode with Cu_2O NWs demonstrates a significant enhancement in photocurrent, from –1.00 to –2.75 mA/cm^2 at –0.8 V versus Ag/AgCl. After optimization of the photoelectrochemical electrode through depositing Pt NPs with atomic layer deposition(ALD) technology on the Cu_2O NWs, the plateau of photocurrent has been enlarged to –7 mA/cm^2 with the external quantum yield up to 34% at 410 nm. This study suggests that the photoelectrode based on Cu_2O NWs is a hopeful system for establishing high-efficiency water splitting system under visible light.

Buckling analysis of super-long rock-socketed filling piles in soft soil area by element free Galerkin method

In order to discuss the buckling stability of super-long rock-socketed filling piles widely used in bridge engineering in soft soil area such as Dongting Lake, the second stability type was adopted instead of traditional first type, and a newly invented numerical analysis method, i.e. the element-free Galerkin method (EFGM), was introduced to consider the non-concordant deformation and nonlinearity of the pile-soil interface. Then, based on the nonlinear elastic-ideal plastic pile-soil interface model, a nonlinear iterative algorithm was given to analyze the pile-soil interaction, and a program for buckling analysis of piles by the EFGM (PBAP-EFGM) and arc length method was worked out as well. The application results in an engineering example show that, the shape of pile top load-settlement curve obtained by the program agrees well with the measured one, of which the difference may be caused mainly by those uncertain factors such as possible initial defects of pile shaft and the eccentric loading during the test process. However, the calculated critical load is very close with the measured ultimate load of the test pile, and the corresponding relative error is only 5.6%, far better than the calculated values by linear and nonlinear incremental buckling analysis (with a greater relative error of 37.0% and 15.4% respectively), which also verifies the rationality and feasibility of the present method.

Challenges and Thoughts on Risk Management and Control for the Group Construction of a Super-Long Tunnel by TBM

The total length of the second stage of the water supply project in the northern areas of the Xinjiang Uygur Autonomous Region is 540 km, of which the total length of the tunnels is 516 km. The total tun- neling mileage is 569 km, which includes 49 slow-inclined shafts and vertical shafts. Among the tunnels constructed in the project, the Ka-Shuang tunnel, which is a single tunnel with a length of 283 kin, is cur- rently the longest water-conveyance tunnel in the world. The main tunnel of the Ka-Shuang tunnel is divided into 18 tunnel-boring machine （TBM） sections, and 34 drilling-and-blasting sections, with 91 tunnel faces. The construction of the Ka-Shuang tunnel has been regarded as an unprecedented challenge for project construction management, risk control, and safe and efficient construction; it has also pre- sented higher requirements for the design, manufacture, operation, and maintenance of the TBMs and their supporting equipment. Based on the engineering characteristics and adverse geological conditions, it is necessary to analyze the major problems confronted by the construction and systematically locate disaster sources. In addition, the risk level should be reasonably ranked, responsibility should be clearly identified, and a hierarchical-control mechanism should be established. Several techniques are put for- ward in this paper to achieve the objectives mentioned above; these include advanced geological prospecting techniques, intelligent tunneling techniques combined with the sensing and fusion of infor- mation about rock parameters and mechanical parameters, monitoring and early-warning techniques, and modern information technologies. The application of these techniques offers scientific guidance for risk control and puts forward technical ideas about improving the efficiency of safe tunneling. These techniques and ideas have great significance for the development of modern tunneling technolo- gies and research into major construction equipment.

Perturbation of symmetries for super-long elastic slender rods

This paper analyses perturbations of Noether symmetry, Lie symmetry, and form invariance for super-long elastic slender rod systems. Criterion and structure equations of the symmetries after disturbance are proposed. Considering perturbation of all infinitesimal generators, three types of adiabatic invariants induced by perturbation of symmetries for the system are obtained.

Electrochemical Introduction of Active Sites into Super-long Carbon Nanotubes for Enhanced Capacitance

Electrochemical cyclic voltammetric（CV） scan was applied to inducing the partial oxidation and defects of carbon nanotubes（CNTs）.The electrochemically induced functional groups and physical defects were demonstrated to show positive effects on the nanotube capacitance,as exemplified by super-long CNT arrays as model for the easy fabrication of CNT electrodes.Specifically,the initial hydrophobic nanotube surface becomes hydrophilic and a ten-time enhancement in capacitance is observed with respect to the pristine CNT sample.Thus,the electrochemical CV pretreatment can be used as an effective approach to activate the CNT surface for an enhanced electrochemical performance in capacitors,and many other advanced devices beyond capacitors,such as electrochemical sensors and batteries.