The supercritical CO_(2) Brayton cycle is considered a promising energy conversion system for Generation IV reactors for its simple layout,compact structure,and high cycle efficiency.Mathematical models of four Brayto...The supercritical CO_(2) Brayton cycle is considered a promising energy conversion system for Generation IV reactors for its simple layout,compact structure,and high cycle efficiency.Mathematical models of four Brayton cycle layouts are developed in this study for different reactors to reduce the cost and increase the thermohydraulic performance of nuclear power generation to promote the commercialization of nuclear energy.Parametric analysis,multi-objective optimizations,and four decision-making methods are applied to obtain each Brayton scheme’s optimal thermohydraulic and economic indexes.Results show that for the same design thermal power scale of reactors,the higher the core’s exit temperature,the better the Brayton cycle’s thermo-economic performance.Among the four-cycle layouts,the recompression cycle(RC)has the best overall performance,followed by the simple recuperation cycle(SR)and the intercooling cycle(IC),and the worst is the reheating cycle(RH).However,RH has the lowest total cost of investment(C_(tot))of$1619.85 million,and IC has the lowest levelized cost of energy(LCOE)of 0.012$/(kWh).The nuclear Brayton cycle system’s overall performance has been improved due to optimization.The performance of the molten salt reactor combined with the intercooling cycle(MSR-IC)scheme has the greatest improvement,with the net output power(W_(net)),thermal efficiencyη_(t),and exergy efficiency(η_(e))improved by 8.58%,8.58%,and 11.21%,respectively.The performance of the lead-cooled fast reactor combined with the simple recuperation cycle scheme was optimized to increase C_(tot) by 27.78%.In comparison,the internal rate of return(IRR)increased by only 7.8%,which is not friendly to investors with limited funds.For the nuclear Brayton cycle,the molten salt reactor combined with the recompression cycle scheme should receive priority,and the gas-cooled fast reactor combined with the reheating cycle scheme should be considered carefully.展开更多
[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface method...[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface methodology. [Results] The optimum extraction conditions of black tea extract by supercritical CO_(2) extraction were as follows: extraction pressure 23.53 MPa, extraction time 1.73 h, and extraction temperature 49.75 ℃, with which the extract yield could reach 5.15% theoretically. [Conclusions] Based on the traditional extraction process, a supercritical extraction method optimized by response surface methodology and a unique extraction process were formed, which enriches the extraction processes and methods of natural raw materials.展开更多
A series of TiO 2-MoO 3 nano-composite photocatalysts were prepared by supercritical fluid dry method(SCFD) and an impregnation technique with TiCl 4 and (NH 4) 6Mo 7O 24 ·4H 2O as the starting materia...A series of TiO 2-MoO 3 nano-composite photocatalysts were prepared by supercritical fluid dry method(SCFD) and an impregnation technique with TiCl 4 and (NH 4) 6Mo 7O 24 ·4H 2O as the starting materials. The catalysts were characterized by the means of XRD, TEM and UV-Vis. Methyl orange was used as model compound for the evaluation of their catalytic activities. The results indicated that the photo-catalyst prepared by SCFD had the advantages of small size(12.84 nm), narrow distribution and good dispersivity. The presence of small amount of Mo in composite catalyst gives rise to the red shift of its absorbance wavelength, decrease of its energy gap and increase of the utility of visible light. Furthermore, higher surface acidity of the photo-catalyst was obtained as the result of the addition of MoO 3. Compared with pure TiO 2, the catalytic activity of the TiO 2-MoO 3 nano-composite photo-catalyst was improved significantly. As the doping concentration of the composite catalysts was controlled at 0.6%(molar percentage), 100% degradation of methyl orange was achieved with in 1.2 h irradiation time.展开更多
Abstract A transonic, high Reynolds number natural laminar flow airfoil is designed and studied. The γ-θ transition model is combined with the shear stress transport （SST） k-w turbulence model to predict the trans...Abstract A transonic, high Reynolds number natural laminar flow airfoil is designed and studied. The γ-θ transition model is combined with the shear stress transport （SST） k-w turbulence model to predict the transition region for a laminar-turbulent boundary layer. The non-uniform free-form deformation （NFFD） method based on the non-uniform rational B-spline （NURBS） basis function is introduced to the airfoil parameterization. The non-dominated sorting genetic algorithm-II （NSGA-II） is used as the search algo- rithm, and the surrogate model based on the Kriging models is introduced to improve the efficiency of the optimization system. The optimization system is set up based on the above technologies, and the robust design about the uncertainty of the Mach number is carried out for NASA0412 airfoil. The optimized airfoil is analyzed and compared with the original airfoil. The results show that natural laminar flow can be achieved on a supercritical airfoil to improve the aerodynamic characteristic of airfoils.展开更多
[Objectives]This study was conducted to improve the sensory quality and industrial availability of tobacco extracts.[Methods]The L9(34)design was adopted to carried out an extraction experiment,in which formula tobacc...[Objectives]This study was conducted to improve the sensory quality and industrial availability of tobacco extracts.[Methods]The L9(34)design was adopted to carried out an extraction experiment,in which formula tobacco was extracted using supercritical CO2,and the extract was concentrated by vacuum distillation.Through sensory evaluation and chemical analysis,the function determination and chemical composition analysis of the tobacco extracts were carried out,and the optimal supercritical fluid extraction process was finally determined.[Results]The obtained optimal supercritical fluid extraction conditions were as follows:extraction temperature 55℃,extraction pressure 25 MPa,CO2 flow rate of 20 L/h,and entrainer of 95%ethanol.The tobacco extract obtained under the optimal conditions endowed the cigarettes with full and delicate aroma,less irritation and clean aftertaste and made the flavor of the cigarettes overall coordinated and softer,so the sensory quality was significantly improved.[Conclusions]The tobacco extract obtained by the supercritical CO2 extraction method from formula tobacco can effectively improve the quality of cigarettes.展开更多
In recent times, the overall interest over Supercritical Fluid Chromatography (SFC) is truly growing within various domains but especially for pharmaceutical analysis. However, in the best of our knowledge modern SFC ...In recent times, the overall interest over Supercritical Fluid Chromatography (SFC) is truly growing within various domains but especially for pharmaceutical analysis. However, in the best of our knowledge modern SFC is not yet applied for drug quality control in the daily routine framework. Among the numerous reported SFC methods, none of them could be found to fully satisfy to all steps of the analytical method lifecycle. Thereby, the present contribution aims to provide an overview of the current and past achievements related to SFC techniques, with a targeted attention to this lifecycle and its successive steps. The included discussions were therefore structured accordingly and emphasizing the analytical method lifecycle in accord with the International Conference on Harmonisation (ICH). Recent and important scientific outputs in the field of analytical SFC, as well as instrumental evolution, qualification strategies, method development methodologies and discussions on the topic of method validation are reviewed.展开更多
The flow pattern of supercritical flow in bend channels is complicated due to the shock wave phenomenon, which creates difficulties with regard to research and design of bend channels. Using the spillway of an actual ...The flow pattern of supercritical flow in bend channels is complicated due to the shock wave phenomenon, which creates difficulties with regard to research and design of bend channels. Using the spillway of an actual project as an example, a three-dimensional numerical investigation was conducted to simulate the flow in a steep-slope bend based on the renormalization group(RNG) k-ε turbulence flow model and the volume of fluid(VOF) method. The validity of the numerical simulation was demonstrated by comparison between the results of numerical simulation and physical model tests. An optimal scheme of setting vertical vanes in the bend channel is presented. The results of numerical simulation and physical model tests are in agreement, which demonstrates the effectiveness of optimization of vertical vanes and the validity of the three-dimensional numerical simulation. Water depths along both bend walls were analyzed numerically and theoretically. The formula for calculating supercritical water depth along either bend wall was derived, and the critical condition of flow separation from the inner wall was determined.展开更多
A series of TiO2-SnO2 nano-sized composite photo-catalysts containing Sn (9.3%-30.1%) were prepared from TiCI4 and SnCl4·5H2O by using sol-gel, supercritical fluid dry and solid-phase reaction (SCFD) combination ...A series of TiO2-SnO2 nano-sized composite photo-catalysts containing Sn (9.3%-30.1%) were prepared from TiCI4 and SnCl4·5H2O by using sol-gel, supercritical fluid dry and solid-phase reaction (SCFD) combination technology. Characterizations with X-ray diffraction (XRD), transmission electron microscopy (TEM) and Fourier Transform Infrared Spectroscopy (FTIR) showed that, in addition to anatase type TiO2, a new active phase (Ti, Sn)O2 (with particle size of 2.0-4.3 nm) formed, and there were no SnO2 crystals observed in the range of the doping concentration studied. Photo-catalytic reaction of phenol was used as a model reaction to evaluate the catalytic activities of the obtained catalysts. Compared with pure TiO2 or Ti-Sn catalyst prepared with general sol-gel method, Ti-Sn nano-composite photo-catalyst thus obtained showed significant improvement in catalytic activity. The photo-catalytic degradation rate of phenol could reach as high as 93.5% after 7 h. The preparation conditions of the new phase (Ti, Sn)O2 were investigated and its catalytic mechanism was proposed. The photo-catalytic particles prepared using SCFD combination technology exhibited small particle size, large surface area and high activity.展开更多
Experimental results on solubility of the styrene, phenol, methylphenylcarbinol, acetophenone, ethyl benzene, propylene glycol and molybdenum as a complex with Trilon B in supercritical CO2 obtained using a dynamic (f...Experimental results on solubility of the styrene, phenol, methylphenylcarbinol, acetophenone, ethyl benzene, propylene glycol and molybdenum as a complex with Trilon B in supercritical CO2 obtained using a dynamic (flow) method are presented. The obtained data are described in the framework of Peng-Robinson equation. The results of the experients on the extraction of organic components from waste formed in the olefin epoxidation process at Nizhnekam-skneftekhim Inc., on the analysis of extract composition, and on the testing of the extract as an epoxidation catalyst are presented. The supercritical water oxidation (SCWO) process of epoxidation process waste was conducted in periodical and continuous mode. The analysis results of reaction product are given. Pilot experiments on dry sediment formation were conducted using Radio Frequency (RF) Inductively Coupled Plasma (ICP) of low pressure.展开更多
Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functio...Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functions of a simply supported beam.Via the direct multi-scale method,the response and stability boundary to the pulsating fluid velocity are solved analytically and verified by the differential quadrature element method(DQEM).The influence of Young's modulus gradient on the parametric resonance is investigated in the subcritical and supercritical regions.In general,the pipe in the supercritical region is more sensitive to the pulsating excitation.The nonlinearity changes from hard to soft,and the non-trivial equilibrium configuration introduces more frequency components to the vibration.Besides,the increasing Young's modulus gradient improves the critical pulsating flow velocity of the parametric resonance,and further enhances the stability of the system.In addition,when the temperature increases along the axial direction,reducing the gradient parameter can enhance the response asymmetry.This work further complements the theoretical analysis of pipes conveying pulsating fluid.展开更多
The nano-crystalline Cu-Ce-Zr-O composite oxides were successfully prepared by the supercritical anti-solvent （SAS） process. The physicochemical properties and catalytic performances were investigated by X-ray diffr...The nano-crystalline Cu-Ce-Zr-O composite oxides were successfully prepared by the supercritical anti-solvent （SAS） process. The physicochemical properties and catalytic performances were investigated by X-ray diffraction （XRD）, Raman spectroscopy, H2 temperature-programmed reduction （H2 -TPR）, oxygen storage capacity （OSC） measurement and catalytic activity evaluation. It was found that Cu2＋ ions incorporated into CeO2 -ZrO2 lattice to form Cu-Ce-Zr-O solid solution associated with the formation of oxygen vacancies. The Cu-Ce-Zr-O catalysts prepared via the SAS process with the Cu content 2.63 mol.% showed the highest OSC index of 636.9 μmol/g. Compared with the samples prepared by impregnation method, Cu doping using SAS process could improve the dispersion of Cu2＋ in the composite oxide, enhance the interaction between Cu2＋ and CeO2-ZrO2 , improve the reducibility of catalyst, and thus improve the OSC performance and increase the catalytic activity for CO oxidation at low temperature.展开更多
基金This work was supported of National Natural Science Foundation of China Fund(No.52306033)State Key Laboratory of Engines Fund(No.SKLE-K2022-07)the Jiangxi Provincial Postgraduate Innovation Special Fund(No.YC2022-s513).
文摘The supercritical CO_(2) Brayton cycle is considered a promising energy conversion system for Generation IV reactors for its simple layout,compact structure,and high cycle efficiency.Mathematical models of four Brayton cycle layouts are developed in this study for different reactors to reduce the cost and increase the thermohydraulic performance of nuclear power generation to promote the commercialization of nuclear energy.Parametric analysis,multi-objective optimizations,and four decision-making methods are applied to obtain each Brayton scheme’s optimal thermohydraulic and economic indexes.Results show that for the same design thermal power scale of reactors,the higher the core’s exit temperature,the better the Brayton cycle’s thermo-economic performance.Among the four-cycle layouts,the recompression cycle(RC)has the best overall performance,followed by the simple recuperation cycle(SR)and the intercooling cycle(IC),and the worst is the reheating cycle(RH).However,RH has the lowest total cost of investment(C_(tot))of$1619.85 million,and IC has the lowest levelized cost of energy(LCOE)of 0.012$/(kWh).The nuclear Brayton cycle system’s overall performance has been improved due to optimization.The performance of the molten salt reactor combined with the intercooling cycle(MSR-IC)scheme has the greatest improvement,with the net output power(W_(net)),thermal efficiencyη_(t),and exergy efficiency(η_(e))improved by 8.58%,8.58%,and 11.21%,respectively.The performance of the lead-cooled fast reactor combined with the simple recuperation cycle scheme was optimized to increase C_(tot) by 27.78%.In comparison,the internal rate of return(IRR)increased by only 7.8%,which is not friendly to investors with limited funds.For the nuclear Brayton cycle,the molten salt reactor combined with the recompression cycle scheme should receive priority,and the gas-cooled fast reactor combined with the reheating cycle scheme should be considered carefully.
文摘[Objectives]Laoshan black tea was subjected to supercritical CO_(2) extraction. [Methods]The extraction conditions of Laoshan black tea were studied by an orthogonal experiment and optimized by response surface methodology. [Results] The optimum extraction conditions of black tea extract by supercritical CO_(2) extraction were as follows: extraction pressure 23.53 MPa, extraction time 1.73 h, and extraction temperature 49.75 ℃, with which the extract yield could reach 5.15% theoretically. [Conclusions] Based on the traditional extraction process, a supercritical extraction method optimized by response surface methodology and a unique extraction process were formed, which enriches the extraction processes and methods of natural raw materials.
文摘A series of TiO 2-MoO 3 nano-composite photocatalysts were prepared by supercritical fluid dry method(SCFD) and an impregnation technique with TiCl 4 and (NH 4) 6Mo 7O 24 ·4H 2O as the starting materials. The catalysts were characterized by the means of XRD, TEM and UV-Vis. Methyl orange was used as model compound for the evaluation of their catalytic activities. The results indicated that the photo-catalyst prepared by SCFD had the advantages of small size(12.84 nm), narrow distribution and good dispersivity. The presence of small amount of Mo in composite catalyst gives rise to the red shift of its absorbance wavelength, decrease of its energy gap and increase of the utility of visible light. Furthermore, higher surface acidity of the photo-catalyst was obtained as the result of the addition of MoO 3. Compared with pure TiO 2, the catalytic activity of the TiO 2-MoO 3 nano-composite photo-catalyst was improved significantly. As the doping concentration of the composite catalysts was controlled at 0.6%(molar percentage), 100% degradation of methyl orange was achieved with in 1.2 h irradiation time.
文摘Abstract A transonic, high Reynolds number natural laminar flow airfoil is designed and studied. The γ-θ transition model is combined with the shear stress transport （SST） k-w turbulence model to predict the transition region for a laminar-turbulent boundary layer. The non-uniform free-form deformation （NFFD） method based on the non-uniform rational B-spline （NURBS） basis function is introduced to the airfoil parameterization. The non-dominated sorting genetic algorithm-II （NSGA-II） is used as the search algo- rithm, and the surrogate model based on the Kriging models is introduced to improve the efficiency of the optimization system. The optimization system is set up based on the above technologies, and the robust design about the uncertainty of the Mach number is carried out for NASA0412 airfoil. The optimized airfoil is analyzed and compared with the original airfoil. The results show that natural laminar flow can be achieved on a supercritical airfoil to improve the aerodynamic characteristic of airfoils.
文摘[Objectives]This study was conducted to improve the sensory quality and industrial availability of tobacco extracts.[Methods]The L9(34)design was adopted to carried out an extraction experiment,in which formula tobacco was extracted using supercritical CO2,and the extract was concentrated by vacuum distillation.Through sensory evaluation and chemical analysis,the function determination and chemical composition analysis of the tobacco extracts were carried out,and the optimal supercritical fluid extraction process was finally determined.[Results]The obtained optimal supercritical fluid extraction conditions were as follows:extraction temperature 55℃,extraction pressure 25 MPa,CO2 flow rate of 20 L/h,and entrainer of 95%ethanol.The tobacco extract obtained under the optimal conditions endowed the cigarettes with full and delicate aroma,less irritation and clean aftertaste and made the flavor of the cigarettes overall coordinated and softer,so the sensory quality was significantly improved.[Conclusions]The tobacco extract obtained by the supercritical CO2 extraction method from formula tobacco can effectively improve the quality of cigarettes.
文摘In recent times, the overall interest over Supercritical Fluid Chromatography (SFC) is truly growing within various domains but especially for pharmaceutical analysis. However, in the best of our knowledge modern SFC is not yet applied for drug quality control in the daily routine framework. Among the numerous reported SFC methods, none of them could be found to fully satisfy to all steps of the analytical method lifecycle. Thereby, the present contribution aims to provide an overview of the current and past achievements related to SFC techniques, with a targeted attention to this lifecycle and its successive steps. The included discussions were therefore structured accordingly and emphasizing the analytical method lifecycle in accord with the International Conference on Harmonisation (ICH). Recent and important scientific outputs in the field of analytical SFC, as well as instrumental evolution, qualification strategies, method development methodologies and discussions on the topic of method validation are reviewed.
文摘The flow pattern of supercritical flow in bend channels is complicated due to the shock wave phenomenon, which creates difficulties with regard to research and design of bend channels. Using the spillway of an actual project as an example, a three-dimensional numerical investigation was conducted to simulate the flow in a steep-slope bend based on the renormalization group(RNG) k-ε turbulence flow model and the volume of fluid(VOF) method. The validity of the numerical simulation was demonstrated by comparison between the results of numerical simulation and physical model tests. An optimal scheme of setting vertical vanes in the bend channel is presented. The results of numerical simulation and physical model tests are in agreement, which demonstrates the effectiveness of optimization of vertical vanes and the validity of the three-dimensional numerical simulation. Water depths along both bend walls were analyzed numerically and theoretically. The formula for calculating supercritical water depth along either bend wall was derived, and the critical condition of flow separation from the inner wall was determined.
基金The authors thank the National Natural Scir nce Foun-dation of China(No.20076004)the National Development Project of High Technology(No.2001AA322030)the Doctoral Program of Higher Education(No.2000001005)for the financial support of this project.
文摘A series of TiO2-SnO2 nano-sized composite photo-catalysts containing Sn (9.3%-30.1%) were prepared from TiCI4 and SnCl4·5H2O by using sol-gel, supercritical fluid dry and solid-phase reaction (SCFD) combination technology. Characterizations with X-ray diffraction (XRD), transmission electron microscopy (TEM) and Fourier Transform Infrared Spectroscopy (FTIR) showed that, in addition to anatase type TiO2, a new active phase (Ti, Sn)O2 (with particle size of 2.0-4.3 nm) formed, and there were no SnO2 crystals observed in the range of the doping concentration studied. Photo-catalytic reaction of phenol was used as a model reaction to evaluate the catalytic activities of the obtained catalysts. Compared with pure TiO2 or Ti-Sn catalyst prepared with general sol-gel method, Ti-Sn nano-composite photo-catalyst thus obtained showed significant improvement in catalytic activity. The photo-catalytic degradation rate of phenol could reach as high as 93.5% after 7 h. The preparation conditions of the new phase (Ti, Sn)O2 were investigated and its catalytic mechanism was proposed. The photo-catalytic particles prepared using SCFD combination technology exhibited small particle size, large surface area and high activity.
文摘Experimental results on solubility of the styrene, phenol, methylphenylcarbinol, acetophenone, ethyl benzene, propylene glycol and molybdenum as a complex with Trilon B in supercritical CO2 obtained using a dynamic (flow) method are presented. The obtained data are described in the framework of Peng-Robinson equation. The results of the experients on the extraction of organic components from waste formed in the olefin epoxidation process at Nizhnekam-skneftekhim Inc., on the analysis of extract composition, and on the testing of the extract as an epoxidation catalyst are presented. The supercritical water oxidation (SCWO) process of epoxidation process waste was conducted in periodical and continuous mode. The analysis results of reaction product are given. Pilot experiments on dry sediment formation were conducted using Radio Frequency (RF) Inductively Coupled Plasma (ICP) of low pressure.
基金Project supported by the National Natural Science Foundation of China (Nos.12002195 and 12372015)the National Science Fund for Distinguished Young Scholars of China (No.12025204)the Program of Shanghai Municipal Education Commission of China (No.2019-01-07-00-09-E00018)。
文摘Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functions of a simply supported beam.Via the direct multi-scale method,the response and stability boundary to the pulsating fluid velocity are solved analytically and verified by the differential quadrature element method(DQEM).The influence of Young's modulus gradient on the parametric resonance is investigated in the subcritical and supercritical regions.In general,the pipe in the supercritical region is more sensitive to the pulsating excitation.The nonlinearity changes from hard to soft,and the non-trivial equilibrium configuration introduces more frequency components to the vibration.Besides,the increasing Young's modulus gradient improves the critical pulsating flow velocity of the parametric resonance,and further enhances the stability of the system.In addition,when the temperature increases along the axial direction,reducing the gradient parameter can enhance the response asymmetry.This work further complements the theoretical analysis of pipes conveying pulsating fluid.
基金Project supported by National Natural Science Foundation of China(20976120)Natural Science Foundation of Tianjin(09JCYBJC06200)
文摘The nano-crystalline Cu-Ce-Zr-O composite oxides were successfully prepared by the supercritical anti-solvent （SAS） process. The physicochemical properties and catalytic performances were investigated by X-ray diffraction （XRD）, Raman spectroscopy, H2 temperature-programmed reduction （H2 -TPR）, oxygen storage capacity （OSC） measurement and catalytic activity evaluation. It was found that Cu2＋ ions incorporated into CeO2 -ZrO2 lattice to form Cu-Ce-Zr-O solid solution associated with the formation of oxygen vacancies. The Cu-Ce-Zr-O catalysts prepared via the SAS process with the Cu content 2.63 mol.% showed the highest OSC index of 636.9 μmol/g. Compared with the samples prepared by impregnation method, Cu doping using SAS process could improve the dispersion of Cu2＋ in the composite oxide, enhance the interaction between Cu2＋ and CeO2-ZrO2 , improve the reducibility of catalyst, and thus improve the OSC performance and increase the catalytic activity for CO oxidation at low temperature.
