This paper studied the thermal physical properties of foundation materials in the molten salt tank of thermal energy storage system after molten salt leakage by Transient plane source experiment and X-ray computed mic...This paper studied the thermal physical properties of foundation materials in the molten salt tank of thermal energy storage system after molten salt leakage by Transient plane source experiment and X-ray computed microtomography simulation methods.The microstructure,thermal properties and pressure resistance with different particle diameters were addressed.The measured heat conductivities from Transient plane source experiment for three cases are 0.49 W/(m·K),0.48 W/(m·K),and 0.51 W/(m·K),and the porosity is 30.1%,30.7%,and 31.2% respectively.The heat conductivity simulating results of three cases are 0.471 W/(m·K),0.482W/(m·K),and 0.513 W/(m·K).The ratio of difference between the results of simulation and Transient plane source measurement is as low as 1.2%,verifying the reliability of experimental and simulation results to a certain degree.Compared with the heat conductivity of 0.097-0.129 W/(m·K) and porosity of 71.6%-78.9% without leaking salt,the porosity is reduced by more than 50% while the heat conductivity increased by 4 to 5 times after molten salt leakage.This significant increase in heat conductivity has a great impact on security operation,structure design,and modeling of the tank foundation for solar power plants.展开更多
In order to investigate the physical mechanism of metal magnetic memory testing, both the influences of earth magnetic field and applied stress on magnetic domain structure were discussed. Static tension and fatigue t...In order to investigate the physical mechanism of metal magnetic memory testing, both the influences of earth magnetic field and applied stress on magnetic domain structure were discussed. Static tension and fatigue tests for low carbon steel plate specimens were carried out on hydraulic servo testing machine of MTS810 type and magnetic signals were measured during the processes by the type of EMS-2003 instrument. The results indicate that the initial magnetic signals of specimens are different before loading. The magnetic signals curves are transformed from initial random to regular pattern due to the effect of two types of loads. However, the shape and distribution of magnetic signal curves in the elastic region are different from that of plastic region in tension test. While in fatigue test those magnetic signals curves corresponding to different cycles are similar. The H_p(y) value of magnetic signals on the fracture zone increases dramatically at the breaking transient time and positive-negative magnetic poles occur on the two parts of fracture zone.展开更多
The infiltration mechanism, which has great significance for the quality control of electrieal contact material made from W-Cu, W-Ag alloys with high content of tungsten, has been studied. And a directive infiltration...The infiltration mechanism, which has great significance for the quality control of electrieal contact material made from W-Cu, W-Ag alloys with high content of tungsten, has been studied. And a directive infiltration technology for improving the product quality and gaining a better economic benefit has been developed.展开更多
The aim of the present study was to compare sealing abilities of Resilon/Epiphany (R/E) with those of guttapercha and Kerr Pulp Canal Sealer EWT (GP/PCS). 50 single rooted teeth were randomly divided into 2 groups (n ...The aim of the present study was to compare sealing abilities of Resilon/Epiphany (R/E) with those of guttapercha and Kerr Pulp Canal Sealer EWT (GP/PCS). 50 single rooted teeth were randomly divided into 2 groups (n = 22) (R/E;GP/PCS), and 2 control groups (n = 3) (Positive, Negative). Fluid flow rate through the filled roots was measured using a fluid filtration device. The same specimens were immersed in a 2% Methylen Blue Solution. Roots were embedded in clear epoxy resin and cross sectionet at 1 mm intervals along the length of the root. Circumferential dye penetration was evaluated at 40× magnification. Fluid filtration of teeth obturated with the R/E system (0.085 [0.057, 0.113] μL·min-1), and dye penetration test showed no statistically significant difference compared to those obturated with GP/PCS (0.113 [0.057, 0.141] μL·min-1). Within the limits of the present study, there is no statistically significant difference between R/E and GP/PCS sealing abilities.展开更多
The lauric-myristic-palmitic acid( LA-MA-PA) ternary eutectic mixtures/expanded graphite( EG) composite phase change materials( PCMs) were prepared by absorbing LA-MA-PA into the porous network of EG. The optimum rati...The lauric-myristic-palmitic acid( LA-MA-PA) ternary eutectic mixtures/expanded graphite( EG) composite phase change materials( PCMs) were prepared by absorbing LA-MA-PA into the porous network of EG. The optimum ratio of ternary eutectic mixtures to EG was determined to be 93∶7 without liquid LA-MA-PA leakage from the composite PCMs. In order to make the structure more stable, the composite PCMs were encapsulated by surface treatment agent to prepare LA-MA-PA/EG encapsulating form-stable PCMs which were characterized by scanning electron microscope( SEM),Fourier transformation infrared spectroscope( FT-IR),differential scanning calorimetry( DSC) and thermal treatment. The results showed there was no chemical reaction between surface treatment agent and LA-MA-PA,and the samples were compactly encapsulated which left almost no imprint on the filter paper after thermal treatment. The phase change temperature and latent heat of LA-MA-PA/EG encapsulating form-stable PCMs were tested to be29. 32 ℃ and 96. 20 J/g,respectively. Additionally,the heat transfer efficiency of heat storage was improved by the addition of EG.展开更多
To rationalize the design of D-π-A type organic small-molecule nonlinear optical materials,a theory guided machine learning framework is constructed.Such an approach is based on the recognition that the optical prope...To rationalize the design of D-π-A type organic small-molecule nonlinear optical materials,a theory guided machine learning framework is constructed.Such an approach is based on the recognition that the optical property of the molecule is predictable upon accumulating the contribution of each component,which is in line with the concept of group contribution method in thermodynamics.To realize this,a Lewis-mode group contribution method(LGC)has been developed in this work,which is combined with the multistage Bayesian neural network and the evolutionary algorithm to constitute an interactive framework(LGC-msBNN-EA).Thus,different optical properties of molecules are afforded accurately and efficientlyby using only a small data set for training.Moreover,by employing the EA model designed specifically for LGC,structural search is well achievable.The origins of the satisfying performance of the framework are discussed in detail.Considering that such a framework combines chemical principles and data-driven tools,most likely,it will be proven to be rational and efficient to complete mission regarding structure design in related fields.展开更多
Because of the radioactivity and toxic nature of nuclear materials, their containment within oxide matrices, encased in sealed containers, has been proposed as a suitable means for storage and transportation. However,...Because of the radioactivity and toxic nature of nuclear materials, their containment within oxide matrices, encased in sealed containers, has been proposed as a suitable means for storage and transportation. However, container failures because of cracks or small orifices present a major leakage risk for nuclear materials, consequently posing a significant hazard to the environment and human beings. In this study, terbium oxide powder was used as a nuclear material representative to examine the leakage of nuclear material powder through orifices located at the base of a pressure container. The dependence of the orifice diameter, the powder layer thickness, and the internal pressure of the container on the leakage mechanism and amount was examined. A simplified model correlating the dependence of the above-mentioned parameters to determine the utmost leakage amount was also developed based on the present results. The leakage of the nuclear material powder was assessed by measuring its concentration using an optical particle counter. The diameter of the orifice determined the powder leakage mechanism, which in turn influenced the amount of leakage produced. Comparison studies showed that unlike the changes in the differential pressure, the volume of the container has little effect on the leakage amount. Under sufficiently high internal pressures, the oxide powder can be released as a fine aerosol. The work is not only crucial from the nuclear safety aspect, but is also beneficial for the safe application of powder and nanoparticles.展开更多
基金supported by the National Natural Science Foundation of China (52036008)。
文摘This paper studied the thermal physical properties of foundation materials in the molten salt tank of thermal energy storage system after molten salt leakage by Transient plane source experiment and X-ray computed microtomography simulation methods.The microstructure,thermal properties and pressure resistance with different particle diameters were addressed.The measured heat conductivities from Transient plane source experiment for three cases are 0.49 W/(m·K),0.48 W/(m·K),and 0.51 W/(m·K),and the porosity is 30.1%,30.7%,and 31.2% respectively.The heat conductivity simulating results of three cases are 0.471 W/(m·K),0.482W/(m·K),and 0.513 W/(m·K).The ratio of difference between the results of simulation and Transient plane source measurement is as low as 1.2%,verifying the reliability of experimental and simulation results to a certain degree.Compared with the heat conductivity of 0.097-0.129 W/(m·K) and porosity of 71.6%-78.9% without leaking salt,the porosity is reduced by more than 50% while the heat conductivity increased by 4 to 5 times after molten salt leakage.This significant increase in heat conductivity has a great impact on security operation,structure design,and modeling of the tank foundation for solar power plants.
文摘In order to investigate the physical mechanism of metal magnetic memory testing, both the influences of earth magnetic field and applied stress on magnetic domain structure were discussed. Static tension and fatigue tests for low carbon steel plate specimens were carried out on hydraulic servo testing machine of MTS810 type and magnetic signals were measured during the processes by the type of EMS-2003 instrument. The results indicate that the initial magnetic signals of specimens are different before loading. The magnetic signals curves are transformed from initial random to regular pattern due to the effect of two types of loads. However, the shape and distribution of magnetic signal curves in the elastic region are different from that of plastic region in tension test. While in fatigue test those magnetic signals curves corresponding to different cycles are similar. The H_p(y) value of magnetic signals on the fracture zone increases dramatically at the breaking transient time and positive-negative magnetic poles occur on the two parts of fracture zone.
文摘The infiltration mechanism, which has great significance for the quality control of electrieal contact material made from W-Cu, W-Ag alloys with high content of tungsten, has been studied. And a directive infiltration technology for improving the product quality and gaining a better economic benefit has been developed.
文摘The aim of the present study was to compare sealing abilities of Resilon/Epiphany (R/E) with those of guttapercha and Kerr Pulp Canal Sealer EWT (GP/PCS). 50 single rooted teeth were randomly divided into 2 groups (n = 22) (R/E;GP/PCS), and 2 control groups (n = 3) (Positive, Negative). Fluid flow rate through the filled roots was measured using a fluid filtration device. The same specimens were immersed in a 2% Methylen Blue Solution. Roots were embedded in clear epoxy resin and cross sectionet at 1 mm intervals along the length of the root. Circumferential dye penetration was evaluated at 40× magnification. Fluid filtration of teeth obturated with the R/E system (0.085 [0.057, 0.113] μL·min-1), and dye penetration test showed no statistically significant difference compared to those obturated with GP/PCS (0.113 [0.057, 0.141] μL·min-1). Within the limits of the present study, there is no statistically significant difference between R/E and GP/PCS sealing abilities.
基金National Science&Technology Pillar Program during the Twelfth Five-Year Plan Period,China(No.2014BAL03B04)
文摘The lauric-myristic-palmitic acid( LA-MA-PA) ternary eutectic mixtures/expanded graphite( EG) composite phase change materials( PCMs) were prepared by absorbing LA-MA-PA into the porous network of EG. The optimum ratio of ternary eutectic mixtures to EG was determined to be 93∶7 without liquid LA-MA-PA leakage from the composite PCMs. In order to make the structure more stable, the composite PCMs were encapsulated by surface treatment agent to prepare LA-MA-PA/EG encapsulating form-stable PCMs which were characterized by scanning electron microscope( SEM),Fourier transformation infrared spectroscope( FT-IR),differential scanning calorimetry( DSC) and thermal treatment. The results showed there was no chemical reaction between surface treatment agent and LA-MA-PA,and the samples were compactly encapsulated which left almost no imprint on the filter paper after thermal treatment. The phase change temperature and latent heat of LA-MA-PA/EG encapsulating form-stable PCMs were tested to be29. 32 ℃ and 96. 20 J/g,respectively. Additionally,the heat transfer efficiency of heat storage was improved by the addition of EG.
基金support by the Key Research and Development Program of Zhejiang Province(2023C01102,2023C01208,2022C01208)。
文摘To rationalize the design of D-π-A type organic small-molecule nonlinear optical materials,a theory guided machine learning framework is constructed.Such an approach is based on the recognition that the optical property of the molecule is predictable upon accumulating the contribution of each component,which is in line with the concept of group contribution method in thermodynamics.To realize this,a Lewis-mode group contribution method(LGC)has been developed in this work,which is combined with the multistage Bayesian neural network and the evolutionary algorithm to constitute an interactive framework(LGC-msBNN-EA).Thus,different optical properties of molecules are afforded accurately and efficientlyby using only a small data set for training.Moreover,by employing the EA model designed specifically for LGC,structural search is well achievable.The origins of the satisfying performance of the framework are discussed in detail.Considering that such a framework combines chemical principles and data-driven tools,most likely,it will be proven to be rational and efficient to complete mission regarding structure design in related fields.
文摘Because of the radioactivity and toxic nature of nuclear materials, their containment within oxide matrices, encased in sealed containers, has been proposed as a suitable means for storage and transportation. However, container failures because of cracks or small orifices present a major leakage risk for nuclear materials, consequently posing a significant hazard to the environment and human beings. In this study, terbium oxide powder was used as a nuclear material representative to examine the leakage of nuclear material powder through orifices located at the base of a pressure container. The dependence of the orifice diameter, the powder layer thickness, and the internal pressure of the container on the leakage mechanism and amount was examined. A simplified model correlating the dependence of the above-mentioned parameters to determine the utmost leakage amount was also developed based on the present results. The leakage of the nuclear material powder was assessed by measuring its concentration using an optical particle counter. The diameter of the orifice determined the powder leakage mechanism, which in turn influenced the amount of leakage produced. Comparison studies showed that unlike the changes in the differential pressure, the volume of the container has little effect on the leakage amount. Under sufficiently high internal pressures, the oxide powder can be released as a fine aerosol. The work is not only crucial from the nuclear safety aspect, but is also beneficial for the safe application of powder and nanoparticles.
