A review on surface coating strategies for anti-hygroscopic of high energy oxidizer ammonium dinitramide

Ammonium dinitramide(ADN),which has the advantages of high energy density,no halogen and low characteristic signal,is not only considered as a new high-energy oxidizer that is expected to replace the traditional oxidizer ammonium perchlorate(AP)in solid propellants,but also a good performance explosive in itself.However,due to the strong hygroscopicity of ADN,its application in solid propellants and explosives is greatly limited.Solving the hygroscopicity of ADN is the key to realize the wide application of ADN.In this paper,we systematically review the research progress of anti-hygroscopic strategies of ADN coating.The surface coating methods are focusing on solvent volatilization,solvent-non-solvent,melt crystallization and atomic layer deposition technology.The characteristics of the different methods are compared and analyzed,and the basis for the classification and selection of the coating materials are introduced in detail.In addition,the feasibility of material for surface coating of ADN is evaluated by several compatibility analysis methods.It is highly expected that the liquid phase method(solvent volatilization method,solvent-non-solvent method)would be the promising method for future ADN coating because of its effective,safety and facile operation.Furthermore,polymer materials,are the preferred coating materials due to their high viscosity,easy adhesion,good anti-hygroscopic effect,and heat resistance,which make ADN weak hygroscopicity,less sensitive,easier to preserve and good compatibility.

Surface Coating of NiTi Shape Memory Alloys with Calcium Phosphates by Dip-coating or Plasma-spraying-biological Characterization Examined by in vitro Testing Methods

The influence of different surface coatings of NiTi shape memory allays was examined using in vitro testing methods. Plates of superelastic nickel-titanium shape memory allay （ NiTi ） were coated with calcium phosphates （ hydroxyapatite ） by high-temperature plasma-spraying or by dip-coating. The biocompatibility was tested in vitro by cultivation of isolated human granulocytes and whole blood cells. As substrates, pure NiTi, plasma-spray-coated NiTi and dip-coated NiTi were used. Isolated granulocytes showed an increased adhesion to both calcium phosphate-coated NiTi samples. Compared to non-coated NiTi or dip-coated NiTi, the number of dead granulocytes adherent to plasma-sprayed surfaces was significantly increased （ p 〈 0.01 ）. Whether the d/f- ferences in apoptosis of granulocytes on dip-coated vs plasma-sprayed coatings observed are due to differences in material surface morphologies has to be analyzed in further studies. Because of the cellular interactions with the coating layers, h is likely that the results obtained are not caused by the underlying NiTi but due to the coating itself.

Homogenous coating of Li^(+)conductive Li_(5)AlO_(4)on single-crystalline nonstoichiometric Li_(1.04)Ni_(0.92)Al_(0.04)O_(2)for rechargeable lithium-ion batteries

Cobalt-free,nickel-rich LiNi_(1-x)Al_(x)O_(2)(x≤0.1)is an attractive cathode material because of high energy density and low cost but suffers from severe structural degradation and poor rate performance.In this study,we propose a molten salt-assisted synthesis in combination with a Li-refeeding induced aluminum segregation strategy to prepare Li_(5)AlO_(4)-coated single-crystalline slightly Li-rich Li_(1.04)Ni_(0.92)Al_(0.04)O_(2).The symbiotic formation of Li_(5)AlO_(4)from reaction between molten lithium hydroxide and doped aluminum in the bulk ensures a high lattice matching between the Ni-rich oxide and the homogenous conductive Li_(5)AlO_(4)that permits high Li^(+)conductivity.Benefiting from mitigated undesirable side reactions and phase evolution,the Li_(5)AlO_(4)-coated single-crystalline Li_(1.04)Ni_(0.92)Al_(0.04)O_(2)delivers a high specific capacity of220.2 mA h g^(-1)at 0.1 C and considerable rate capability(182.5 mA h g^(-1)at 10 C).Besides,superior capacity retention of 90.8%is obtained at 1/3 C after 100 cycles in a 498.1 mA h pouch full cell.Furthermore,the particulate morphology of Li_(1.04)Ni_(0.92)Al_(0.04)O_(2)remains intact after cycling at a cutoff voltage of 4.3 V,whereas slightly Li-deficient Li_(0.98)Ni_(0.97)Al_(0.05)O_(2)features intragranular cracks and irreversible lattice distortion.The results highlight the value of molten salt-assisted synthesis and Li-refeeding induced elemental segregation strategy to upgrade Ni-based layered oxide cathode materials for advanced Li-ion batteries.

Surface modification with SiO_2 coating on biomedical TiNi shape memory alloy by sol-gel method

The effect of heat treatment on the transformation temperature of Ti?52.2%Ni (mole fraction) alloy was studied using differential scanning calorimetry (DSC). The transformation temperatures of the alloy can be adjusted effectively by heat treatment. Dense and stable SiO2 coatings were deposited on the surface of the pre-oxidized TiNi alloy by sol?gel method. The bonding strength of films and matrix was (65.9±1.5) N. The electrochemical corrosion test shows that the TiNi alloy with SiO2 coating has excellent corrosion resistance in the Hank’s simulated body fluid. The release behaviors of Ni ion of the alloy with and without SiO2 coating implanted in the acoustic vesicle of guinea pig were studied by EDS testing, which was inhibited effectively by the dense and stable SiO2 coating on the alloy.

Advances in Mg-Al-layered double hydroxide steam coatings on Mg alloys:A review

Layered double hydroxide(LDH)coatings on magnesium(Mg)alloys shine brightly in the field of corrosion protection because of their special ion-exchange function.State-of-the-art steam coating as a type of LDH film preparation technique has emerged in recent years because only pure water is required as the steam source and its environmentally friendly LDH coating fits the current need for green development.Moreover,this coating can effectively inhibit the corrosion of the Mg alloy substrate due to the chemical bonding between the coating and the Mg alloy substrate.This review systematically explains cutting-edge advancements in the growth mechanism and corrosion behavior of LDH steam coatings,and analyzes the advantages and limitations of the steam-coating method.The influencing factors including pressure,CO_(2)/CO_(3)^(2-),aluminum content of the substrate alloy,solution type,and acid-pickling pretreatment,as well as the post-treatment of steam-coating defects,are comprehensively elucidated,providing new insights into the development of the in situ steam-coating technique.Finally,existing issues and future prospects are discussed to further accelerate the widespread application of Mg alloys.

New Nano Polymer Materials for Composite Exterior-Wall Coatings

A triethylenetetramine epoxy mixture was synthesized through the reaction of a low-molecular-weight liquid epoxy resin with triethylenetetramine(TETA).Then triethyltetramine(TETA)was injected dropwise into a pro-pylene glycol methyl ether(PM)solution for chain extension reaction.A hydrophilic andflexible polyether seg-ment was introduced into the hardener molecule.The effects of TETA/DGEPG,reaction temperature and reaction time on the epoxy conversion of polyethylene glycol diglycidyl ether(DGEPG)were studied.In addition,several alternate strategies to add epoxy resin to the high-speed dispersion machine and synthesize MEA DGEBA adduct(without catalyst and with bisphenol A diglycidyl ether epoxy resin)were compared.It was found that the higher the molecular weight of triethylenetetramine,the longer the chain segment of the surface active molecule.When the equivalence ratio of amine hydrogen and epoxy group is low,the stability of lotion is good.When the ratio of amine hydrogen to epoxy group is large,the content of triethylenetetramine is small.The main objective of this study is the provision of new data and knowledge for the development of new materials in the coating and electronic industry.

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

In this work, an in situ synthesized TiC-reinforced metal matrix composite （MMC） coating of approximately 350-400μm thickness was fabricated on a gray cast iron （GCI） substrate by plasma transferred arc （PTA） surface alloying of Ti-Fe alloy powder. Microhard- ness tests showed that the surface hardness increased approximately four-fold after the alloying treatment. The microstructure of the MMC coating was mainly composed of residual austenite, acicular martensite, and eutectic ledeburite. Scanning electron microscopy （SEM） and X-ray diffraction analyzes revealed that the in situ TiC particles, which were formed by direct reaction of Ti with carbon originally contained in the GCI, was uniformly distributed at the boundary of residual anstenite in the alloying zone. Pin-on-disc high-temperature wear tests were performed on samples both with and without the MMC coating at room temperature and at elevated temperatures （473 K and 623 K）, and the wear behavior and mechanism were investigated. The results showed that, after the PTA alloying treatment, the wear resistance of the sam- ples improved significantly. On the basis of our analysis of the composite coatings by optical microscopy, SEM with energy-dispersive X-ray spectroscopy, and microhardness measurements, we attributed this improvement of wear resistance to the transformation of the microstruc- ture and to the presence of TiC particles.

Preparation of cerium oxide based environment-friendly chemical conversion coating on magnesium alloy with additives

Ce（SO4）2？H2O2 solution was adopted to prepare a chemical conversion coating on AZ91D magnesium alloy.Additives of Ni（NO3）2 and sodium dodecyl benzene sulfonate were applied to improving the coating formation.SEM,EDS,XRD and GIXD were adopted to study the coating morphology,structure and composition,and the potential change curve in the treating solution was recorded to study the coating growth.Sodium dodecyl benzene sulfonate makes a remarkable improvement in the coating compactness,and shortens the time in the second stage of the coating formation from 5 min to 2 min.Compared to Ni（NO3）2,sodium dodecyl benzene sulfonate makes the more remarkable effect on the corrosion resistance improvement,since it can decrease the current density of corrosion from 7.41×10-5 A/cm2 to 2.20×10-5 A/cm2.The additives of Ni（NO3）2 and sodium dodecyl benzene sulfonate can enhance the Ce content from 18.92% to 22.32% and 25.08% in the coating,respectively.The XRD and GIXD results indicated that all the conversion coating formed in different solutions exhibit amorphous structure.

Nucleation and growth behavior of coating film on Mg–Al–Zn alloy with different surface topographies via plasma electrolytic oxidation

This work was made to investigate how nucleation and growth behavior of the coating film were affected by surface topographies of Mg–Al–Zn alloy substrate during the initial stage of plasma electrolytic oxidation(PEO).To satisfy this end,a single substrate was prepared by mechanical treatment exhibiting rough and smooth regions with an equal area on the surface.The rough region with prominent hills and grooves induced the breakdown of passive film,which was indicated by an early appearance of plasma discharge on the rough region since nucleation of coating film occurred preferentially around the hills.However,the coating film grown on the grooves was somewhat thicker and more porous than the film grown on the hills and smooth regions.This was due to the fact that the growth of the coating film was found to be localized in the presence of rough region,which was in line with the discharge activities.Herein,the nucleation and growth behavior during the initial stage of PEO will be discussed schematically on the basis of microstructural interpretation.

Laser surface alloying fabricated porous coating on NiTi shape memory alloy

Laser surface alloying technique was applied to fabricate a metallic porous coating on a solid NiTi shape memory alloy. By laser surface alloying a 40%TiH2-60%NiTi powder mixture on the surface of NiTi alloy using optimized laser process parameters, a porous but crack-free NiTi layer can be fabricated on the NiTi substrate. The porous coating is metallurgically bonded to the substrate NiTi alloy. The pores are uniformly distributed and are interconnected with each other in the coating. An average pore size of less than 10 μm is achieved. The Ni content of the porous layer is much less than that of the original NiTi surface. The existence of the porous coating on the NiTi alloy causes a 37% reduction of the tensile strength and 55% reduction of the strain as compared with the NiTi alloy. Possible biomedical or other applications for this porous surface with good mechanical strength provided by the substrate are prospective.

Preparation and Corrosion Resistance of Rare Earth Conversion Coatings on AZ91 Magnesium Alloy

The feasibility of forming pollution-free and environmentally benign Ce-based rare earth conversion coatings （short for RECCs） on AZ91 magnesium alloy to enhance corrosion resistance was studied. The effect of optimum processing parameters on corrosion resistance of RECCs, such as density of treating solution, temperature and time of coating formation were discussed. Protective performance of conversion coatings on magnesium alloy was evaluated by moisture/heating test, anodic polarization, etc. The results show that Ce-based RECCs under moisture/heating condition can remain intact, with high coverage and no obvious corrosion phenomenon. Corrosion potential increases and passive phenomenon occurs while current density decreases, therefore Ce-based RECCs can improve corrosion resistance of AZ91 magnesium alloy. The morphology of Ce-based RECCs prepared under optimum process through SEM observation is found to be a few particles coherent to the base coating, and the coating has no cracks and exhibits apparent corrosion resistance during corrosion courses of AZ91 magnesium alloy.

Measurement of Atrazine Adsorption onto Surficial Sediments(Natural Surface Coatings)——New Evidence for the Importance of Fe Oxides

To reveal the relative contribution of the components, Fe, Mn oxides or organic materials（OMs） in the surficial sediments（SSs）, and the natural surface coating samples（NSCSs） to adsorbing atrazine（AT）, a selective chemical extraction technique was employed, to remove the different components, and the adsorption characteristics of AT on the SSs and the NSCSs were investigated. The observed adsorptions of AT on the original and extracted SSs and NSCSs were analyzed by nonlinear least squares fitting（NLSF） to estimate the relative contribution of the components. The results showed that the maximum adsorption of AT on the NSCSs was greater than that in the SSs, before and after extraction treatments, implying that the NSCSs were more dominant than the SSs for organic pollutant adsorption. It was also found that the Fe oxides, OMs, and residues in SSs（NSCSs） facilitated the adsorption of AT, but Mn oxides directly or indirectly restrained the interaction of AT with SSs（NSCSs） particles. The contribution of the Fe oxides to AT adsorption was more than that of OMs; the greatest contribution to AT adsorption on a molar basis was from the Fe oxides in the nonresidual fractions, indicating that the Fe oxides played an important role in controlling the environmental behavior of AT in an aquatic environment.

High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

A review of effective strides in amelioration of the biocompatibility of PEO coatings on Mg alloys

Recently,developing bioactive and biocompatible materials based on Mg and Mg-alloys for implant applications has drawn attention among researchers owing to their suitable body degradability.Implementing Mg and its alloys reduces the risk of long-term incompatibility with tissues because of their close mechanical properties and no need for re-operation to remove the implant.Nevertheless,the degradation rate of the implant needs to be controlled because production of hydrogen gas and accumulation of its bubbles increases local pH around the implants.To confine the integrity of implants and the body,the corrosion concern in the body fluid requires to be addressed.Surface modification as one of the effective strategies can improve corrosion resistance.Besides,it creates a suitable surface for bone grafting and cell growth.The development of proper surface-coated implants needs appropriate techniques and approaches.Plasma electrolytic oxidation(PEO)coating can provide long-term protection by providing a ceramic layer and improving the implant’s biocompatibility.Herein,a general review of in-vivo and in-vitro evaluation of PEO coatings on Mg and Mg-alloys has been carried out.Recent advances in surface modification on Mg and Mg-alloys have been discussed,however,the need for reliable laboratory models to predict in-vivo degradation is still valid.

Effects of F-Si sealer on electrochemical characteristics of 15%Al-85%Zn alloy thermal spray coating

Most hulls of the ships are protected with paintings, sacrificial anode, and impressed current cathodic protection methods against corrosion problems. However, these conventional methods are not very effective because the rudder of ships stern are exposed to very severe corrosive environment such as tides, speeds of ships, cavitations and erosion corrosion. The environmental factors such as cavitation and corrosion will cause damage for materials with the shock wave by the creation and destruction of bubble. To solve these problems, the cavitation and electrochemical experiments are executed for thermal spray coating with Al-Zn alloy wire material. Thereafter, and sealed specimens with F-Si sealer on Al-Zn alloy coated specimen are executed to improve electrochemical and anti-cavitation characteristics in sea water. The application of fluorine silicon sealing after spray coating of 15%Al-85%Zn seems to be appropriate not only in static environment but also in dynamic environment.

Study on Phytic Acid Conversion Coating on Mg-Li Alloy

The impact of phytic acid concentration,immersion time and soaking temperature on phytic acid conversion coating of the Mg-Li alloy are studied.The surface morphology and the corrosion of the phytic acid conversion coating are tested by using scanning electron microscopy and the electrochemical analyzer.The results show that phytic acid concentration and immersion time,soaking temperature affects the microstructure and corrosion resistance of the phytic acid conversion coating.There is a passivation interval with a smaller capacitor and larger resistor in the phytic acid conversion coating.The phytic acid conversion coating is made up of white particle and flake film.

Comparison of the effects of pre-activators on morphology and corrosion resistance of phosphate conversion coating on magnesium alloy

In this study, Mg–6.0Zn–3.0Sn–0.5Mn(ZTM630) magnesium alloy was pre-activated by colloidal Ti, oxalic acid, and phosphoric acid,and a phosphate conversion coating(PCC) was prepared on the alloy surface. The morphology and corrosion resistance of the prepared PCCs were investigated. Surface morphology studies showed that the phosphate crystals that formed the coating were the smallest for the sample pre-activated by phosphoric acid. The coating on the colloidal Ti and the phosphoric acid samples had the largest and the smallest thickness and surface roughness, respectively. The reason for the discrepancy was analyzed by comparing the surface morphologies of alloy samples immediately after the pre-activation treatment and various phosphating treatments. X-ray diffraction analysis revealed that all three PCCs contained the same compounds. The corrosion resistance time from the copper sulfate drop test and the electrochemical data from the potentiodynamic polarization curves showed that the coating pre-activated by phosphoric acid had the best corrosion resistance. Finally, the 1500 h neutral salt spray corrosion test confirmed that the phosphating treated magnesium alloy, which was pre-activated by phosphoric acid,exhibited excellent corrosion resistance and behavior.

Surface modification and functionalization by electrical discharge coating:a comprehensive review

Hard coatings are extensively required in industry for protecting mechanical/structural parts that withstand extremely high temperature,stress,chemical corrosion,and other hostile environments.Electrical discharge coating(EDC)is an emerging surface modification technology to produce such hard coatings by using electrical discharges to coat a layer of material on workpiece surface to modify and enhance the surface characteristics or create new surface functions.This paper presents a comprehensive overview of EDC technologies for various materials,and summarises the types and key parameters of EDC processes as well as the characteristics of resulting coatings.It provides a systematic summary of the fundamentals and key features of the EDC processes,as well as its applications and future trends.

Lead adsorption capacities of different components in natural surface coatings

Pb adsorption capacities of Fe oxide, Mn oxide and organic materials in natural surface coatings(biofilms and associated minerals) collected in three lakes, two ponds and a river in Jilin Province, China and Cayuga Lake in US were studied. A novel extraction technique was employed to remove one or more component(s) from the surface coatings. Pb adsorption to surface coatings before and after extraction was performed to determine the adsorptive properties of the extracted component(s). The statistical analysis of observed Pb adsorption was carried out using nonlinear least squares fitting(NLSF) to estimate the Pb adsorption capacity of each component of surface coatings. For each body of water, the estimated Pb adsorption capacity of Mn oxide(mol Pb/mol Mn) was significantly higher than that of Fe oxide(mol Pb/ mol Fe). The value of estimated adsorption capacities of organic materials with the unit mol Pb per kg COD was similar to or less than that of Fe oxides with the unit mol Pb per mol Fe. Comparison of components of surface coatings in different waters showed that the estimated Pb adsorption capacities of components in surface coatings developed in different natural waters were different, especially for Mn oxides.

Microstructure and sliding wear behavior of pseudo-alloy PS45/CuAl8 composite coating sprayed by HVAA technique

A pseudo-alloy PS45/CuAl8 composite coating was sprayed on steel substrate by high-velocity activated arc spraying (HVAA) process. Its sliding wear behavior at room temperature was evaluated by M-2000 wear tester. For comparison, a single CuAl8 coating was also prepared and tested under the same conditions. It is found that the pseudo-alloy composite coating consists of α-Cu and γ-Ni metallic matrix phases together with homogenously distributed minor Al 2 O 3 , Cr 2 O 3 oxide phases. Moreover, pseudo-alloy coating possesses much better sliding wear resistance than CuAl8 coating due to the enhanced hardness and microstructural homogenization. Fatigue wear and abrasive wear are responsible for the wear-down mechanism of the pseudo-alloy coating.