XPS STUDIES ON SURFACE MODIFIED POLY [1-(TRIMETHYLSILYL)-1-PROPYNE] MEMBRANES Ⅱ SURFACE MODIFICATION BY BROMINE VAPOR

Surface modification of poly [1-(trimethylsilyl)-1-propyne] (PTMSP) membranes bybromine vapor has been studied. It is shown that Br/C atomic ratio at the surfaces increased withthe time of bromination until about 60 min, then it reached a plateau. The results of XPS and IRstudies indicated that the addition of bromine to double bonds and the replacement of H on CH_3 bybromine had taken place so that a new peak at 286.0 eV (C--Br)in C_(1s) spectra and some newbands, e. g. at 1220 and 580cm^(-1) in IR spectra were formed. The fact,t Po_2, permeability ofoxygen, decreased and α_(O_2/N_2), separation factor of oxygen relative to nitrogen, increased withbromination time, shows that surface modification of PTMSP by bromine may be an efficient approach to prepare PTMSP membranes used for practical gas separations.

Influence of laser parameters on the microstructures and surface properties in laser surface modification of biomedical magnesium alloys

Biodegradable implants from magnesium(Mg)alloys have emerged in the biomedical field especially in the orthopedic and cardiovascular stent applications owing to their low density,high specific strength,excellent machinability,good biocompatibility,and biodegradability.The primary shortcoming of Mg-based implants is their low corrosion resistance in the physiological environment,which results in premature mechanical integrity loss before adequate healing and the production of excessive hydrogen gas,which is harmful to the body tissues and negatively affects the biocompatibility of the implant.Laser surface modification has recently received attention because it can improve the surface properties such as surface chemistry,roughness,topography,corrosion resistance,wear resistance,hydrophilicity,and thus cell response to the surface of the material.The composition and microstructures including textures and phases of laser-treated surfaces depend largely on the laser processing parameters(input laser power,laser scan velocity,frequency,pulse duration,pressure,gas circulation,working time,spot size,beam focal position,and laser track overlap)and the thermophysical properties of the substrate(solubility,melting point,and boiling point).This review investigates the impacts of various laser surface modification techniques including laser surface melting,laser surface alloying,laser cladding,laser surface texturing,and laser shock peening,and highlights their significance in improving the surface properties of biodegradable Mg alloys for implant applications.Additionally,we explore how different laser process parameters affect its composition,microstructure,and surface properties in each laser surface modification technique.

Effect of surface modification on the radiation stability of diamond ohmic contacts

The ohmic contact interface between diamond and metal is essential for the application of diamond detectors.Surface modification can significantly affect the contact performance and eliminate the interface polarization effect.However,the radiation stability of a diamond detector is also sensitive to surface modification.In this work,the influence of surface modification technology on a diamond ohmic contact under high-energy radiation was investigated.Before radiation,the specific contact resistivities(ρc)between Ti/Pt/Au-hydrogen-terminated diamond(H-diamond)and Ti/Pt/Au-oxygenterminated diamond(O-diamond)were 2.0×10^(-4)W·cm^(2) and 4.3×10^(-3)Wcm^(2),respectively.After 10 MeV electron radiation,the ρc of Ti/Pt/Au H-diamond and Ti/Pt/Au O-diamond were 5.3×10^(-3)W·cm^(2)and 9.1×10^(-3)W·cm^(2),respectively.The rates of change of ρc of H-diamond and O-diamond after radiation were 2550%and 112%,respectively.The electron radiation promotes bond reconstruction of the diamond surface,resulting in an increase in ρc.

Recent Advances in Structural Optimization and Surface Modification on Current Collectors for High‑Performance Zinc Anode:Principles,Strategies,and Challenges

The last several years have witnessed the prosperous development of zinc-ion batteries(ZIBs),which are considered as a promising competitor of energy storage systems thanks to their low cost and high safety.However,the reversibility and availability of this system are blighted by problems such as uncontrollable dendritic growth,hydrogen evolution,and corrosion passivation on anode side.A functionally and structurally well-designed anode current collectors(CCs)is believed as a viable solution for those problems,with a lack of summarization according to its working mechanisms.Herein,this review focuses on the challenges of zinc anode and the mechanisms of modified anode CCs,which can be divided into zincophilic modification,structural design,and steering the preferred crystal facet orientation.The possible prospects and directions on zinc anode research and design are proposed at the end to hopefully promote the practical application of ZIBs.

Using pectin to separate talc and molybdenite through the surface modification with Cu^(2+):Applications and mechanism

Organic depressants have low selectivity in separating molybdenite and talc because their metal sites lack activity for organics chemisorption.In this study,surface modification by copper sulfate was used to induce the differential adsorption of pectin onto molybdenite and talc surfaces for enhanced flotation separation.Contact-angle experiments,scanning electron microscopy,adsorption measurements,timeof-flight secondary-ion mass spectrometry,and X-ray photoelectron spectroscopy analyses were conducted to reveal the interaction mechanism.Results illustrated that molybdenite and talc could not be separated using pectin alone,while molybdenite was selectively depressed after surface modification by copper sulfate and this effect was strengthened under alkaline conditions.Metal sites(Mg,Si and Mo)of talc and molybdenite themselves were unable to react with pectin,whereas Cu+would deposit and further function as active site for pectin chemisorption after surface modification.However,the quantity of deposited Cu sites dropped on talc surface and increased on molybdenite surface with increased pH,and the Mo atoms of molybdenite crystal were activated to take part in pectin chemisorption.Therefore,more pectin was adhered on molybdenite surface,which imparted molybdenite stronger wettability.Herein,surface-modification through metal ions can enable the differential adsorption of organic depressants and enhance the flotation separation of minerals.

A review on developing high-performance ZE41 magnesium alloy by using bulk deformation and surface modification methods

Magnesium(Mg)alloys are generally used in light-weight structural applications due to their higher specific strength.However,the usage of these Mg alloys is limited due to their poor formability at room temperature,which is attributed to lower count of slip systems associated with the hcp crystal structure.To address these limitations,several new magnesium alloys and also many processing strategies have been developed and reported in the literature.ZE41 Mg is an alloy with significant quantities of zinc(Zn)and rare earth(RE)elements and has emerged as a promising material for aerospace,automotive,electronics,biomedical and many other industries.To make this alloy more competitive and viable,it should possess better mechanical and corrosion properties.Hence,the current paper reviews the effect of bulk mechanical processing on grain refinement,microstructural modification,and corresponding changes in the mechanical behaviour of ZE41Mg alloy.Further,the effect of various surface modification techniques on altering the surface microstructure and surface properties such as wear and corrosion are also briefly summarized and presented.This review also discusses the challenges and the future perspectives in developing high-performing ZE41 Mg alloys.

Current Strategies of Surface Modifications to Polyurethane Biomaterials for Vascular Grafts

As the number of patients suffering from cardiovascular diseases and peripheral vascular diseases rises,the constraints of autologous transplantation remain unavoidable.As a result,artificial vascular grafts must be developed.Adhesion of proteins,platelets and bacteria on implants can result in stenosis,thrombus formation,and postoperative infection,which can be fatal for an implantation.Polyurethane,as a commonly used biomaterial,has been modified in various ways to deal with the adhesions of proteins,platelets,and bacteria and to stimulate endothelium adhesion.In this review,we briefly summarize the mechanisms behind adhesions,overview the current strategies of surface modifications of polyurethane biomaterials used in vascular grafts,and highlight the challenges that need to be addressed in future studies,aiming to gain a more profound understanding of how to develop artificial polyurethane vascular grafts with an enhanced implantation success rate and reduced side effect.

Surface modification of CeO_(2-x) nanorods with Sn doping for enhanced nitrogen electroreduction

While the electrochemical nitrogen reduction reaction(NRR) represents a prospective blueprint for environmentally renewable ammonia generation,it has yet to overcome the limitations of weak activity and inferior selectivity.In this regard,surface modification tactic was constructed to markedly enhance the activity and selectivity via introducing Sn atoms into the surface of defective cerium oxide(denoted as Sn-CeO_(2-x)) as the active and robust electrocatalyst for NRR under benign environment.The introduction of Sn atoms in CeO_(2-x)can not only inhibit the HER activity of the catalyst but also modulate the electronic structure of ceria and optimize N-Ce interaction,thus enhancing NRR activity and selectivity.Outperforming all previous CeO_(2)-based NRR catalysts,this catalyst has demonstrated an ammonia yield rate of 41.1 μg mg_(cat)^(-1) h^(-1) and an exceptional Faradic efficiency of 35.3%.This work presents a viable approach for the development of advanced NRR electrocatalysts.

Etching characteristics and surface modification of InGaSnO thin films under Cl_(2)/Ar plasma

Indium gallium tin oxide(IGTO)thin films have the potential for high mobility and lowtemperature processing,which makes them suitable for applications such as display backplanes and high-voltage switching devices.However,very few studies have investigated the plasmaetching characteristics of IGTO and changes in its properties after etching.In this study,the etching characteristics of IGTO were investigated using Cl_(2)/Ar plasma,and changes in surface properties were analyzed.Results showed that the etch rate increased with an increase in the proportion of Cl_(2),with the highest etch rate observed at 69 nm min^(-1)in pure Cl_(2)plasma with a gas flow rate of 100 sccm.Furthermore,increased radio-frequency power caused a rise in the etch rate,while a process pressure of 15 m Torr was optimal.The primary etching mechanism for IGTO thin films under Cl_(2)plasma was a chemical reaction,and an increased work function indicated the occurrence of defects on the surface.In addition,the etching process reduced the surface roughness of Cl_(2)-containing plasma,whereas the etching process in pure Ar plasma increased surface roughness.This study contributes to a better understanding of the plasmaetching characteristics of IGTO and changes in its properties after etching,providing valuable insights for IGTO-based applications.

Adjusting the interfacial adhesion via surface modification to prepare high-performance fibers

Ultra-high molecular weight polyethylene(UHMWPE)fiber is a new kind of high-performance fiber.Due to its excellent physical and chemical characteristics,it is widely used in various fields.However,the surface UHMWPE fiber is smooth and demonstrates no-polar groups.The weak interfacial adhesion between fiber and resin seri-ously restricts the applications of UHMWPE fiber.Therefore,the surface modification treatments of UHMWPE fiber are used to improve the interfacial adhesion strength.The modified method by adding nanomaterials elu-cidates the easy fabrication,advanced equipment and proper technology.Thus,the progress of UHMWPE nanocomposite fibers prepared via adding various nanofillers are reviewed.Meanwhile,the effects of other various methods on surface modification are also reviewed.This work advances the various design strategies about nano technologies on improving interfacial adhesion performance via treatment methodologies.

Surface Modification of Fluororubber Using Atmospheric Pressure Dielectric Barrier Discharge(DBD)

Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topography and surface chemistry of the treated F2311 films were characterized by contact angle measurement, atomic force microscopy （AFM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The experimental results showed that a short time air plasma treatment led to morphological, wettability and chemical changes in the F2311 films. The surface hydrophilicity increased greatly after the plasma treatment, the static water contact angle decreased from 98.6° to 32°, and oxygen containing groups （C=O, O-C=O, etc. ） were introduced. Atomic force microscopy revealed that plasma produced by DBD etched F2311 films obviously. The roughness of the samples increased remarkably with the formation of peaks and valleys on the treated surfaces. The increased surface wettability may be correlated with both the introduction of hydrophilic groups due to air plasma oxidation of the surface and the change in surface morphology etched by DBD.

Characterization of Oxygen Species on MgO(100) Surface by XPS andSRPES

The present work reported the results of the characterization of the surface oxygen species on single crystal MgO(100) using surface sensitive analyzing methods ARXPS(angular resolved X-ray photoelectron spectroscopy) and SRPES (synchrotron radiation photoelectron spectroscopy).

Surface Modification of Fly Ashes with Carbide Slag and Its Effect on Compressive Strength and Autogenous Shrinkage of Blended Cement Pastes

Surfaces of grade III fly ashes were modified through mixing with carbide slag and calcining at 850 ℃ for 1 h. Mineralogical compositions and surface morphology of fly ashes before and after modification were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）, respectively. Effect of surface-modified fly ashes on compressive strength and autogenous shrinkage of blended cement pastes was investigated. Microstructures of cement pastes were examined by backscattered electron （BSE） imaging and mercury intrusion porosimetry （MIP）. The experimental results showed that β-C2S was formed on the surfaces of fly ashes after modification. Hydration ofβ-C2S on the surface-modified fly ashes densified interface zone and enhanced bond strength between particles of fly ashes and hydrated clinkers. In addition, surface modification of fly ashes tended to decrease total porosity and 10-50 nm pores of cement pastes. Surface modification of fly ashes increased compressive strength and reduced autogenous shrinkage of cement pastes.

Synthesis and Characteristics of Mesoporous Silica Aerogels with One-step Solvent Exchange/Surface Modification

The synthesis procedures and physical properties of the ambient dried hydrophobic silica aerogels by using different contents of ethanol （EtOH）/trimethylchlorosilane （TMCS）/n-Hexane as surface modification agent were investigated. One-step solvent exchange and surface modification were simultaneously progressed by immersing silica hydrogels in EtOH/TMCS/n-Hexane solution. It is found that microstructures as well as properties of silica aerogels like porosity, specific density and specific surface area are affected by the contents of surface modification agent in the sol from the results of SEM, TEM morphology, FT-IR chemical structure, BET surface area and BJH pore size analyses. The volume of TMCS is of 10% and 20% of hydrogels, and the final product is hydrophilic xerogels. When TMCS＇s percent （v/v） is elevated to 75 %-100%, hydrophobic silica aerogels with good performance are synthesized, the porosities of aerogels are in the range of 93.5%-95.8% and the average pore size diameter is less than 20 nm.

Mechanism of Surface Modification for Sericite

Surface modification of sericite by wet method was conducted with the addition of 1.0 % （w/w） silane. The resulting wetting contact angle and activity ratio of sericite were 130° and 98% respectively. Good pre-evaluation indexes of oil value （40.8%） and dispersivity （14.0 mL） were obtained. When 30 % of sericite was filled into acrylonitrile butadiene styrene（ABS） plastic, the bending strength and tensile strength of the composite material were reduced by 7% and 14.3% in comparison to those of pure ABS plastic, while the rigidity was increased by 3 times, and the impact strength and breaking elongation were reduced significantly. The mechanism of surface modification was investigated and the configuration of silane coupling agent on the surface of sericite was given. Infrared （IR） spectroscopic analysis indicates that the adsorption of silane on the surface of sericite belongs to chemical adsorption.

Surface Modification of Polyethylene (PE) Films Using Dielectric Barrier Discharge Plasma at Atmospheric Pressure

Modification of the surface properties of polyethylene （PE） films is studied using air dielectric barrier discharge at atmospheric pressure. The treated samples are examined by Water contact angle measurements, Fourier transform infrared attenuated total reflection spectroscopy （FTIR-ATR）, X-ray photoelectron spectroscopy （XPS） and scanning electron microscopy （SEM）. With the increase in treating time, the water contact angle changes from 93.2° before treatment to a minimum of 53.3° after a treatment for 50 s. Both ATR and XPS results show some oxidized species are introduced into the sample surface by the plasma treatment and the tendency of the water contact angle with the treating time is the same as that of oxygen concentration on the treated sample surface. SEM result shows the surface roughness of PE samples increases with the treatment time increasing.

Surface Modification of Fire-retardant Asphalt with Silane Coupling Agent

The theory and approach of the surface modified of asphalt fire-retardant with silane coupling agent were introduced. The optimum silane dosage was determined, and the structure and properties of the asphalt fire-retardant before and after the surface modification were characterized by infrared spectrum and thermo gravimetric analysis. The dispersion effect of asphalt flre-retardant was studied. The influence of the surface modification on the hydrophilicity and lipophilicity of the asphalt fire-retardant was analyzed. The experimental results showed that there were physical and chemical interactions between the silane coupling agent and the asphalt fire-retardant, which reduced the surface polarity of the asphalt fire retardant. The optimum silane coupling agent dosage was 0.95% of the asphalt fire retardant. The surface modification improved the thermal stability, dispersibility and lipophilicity of the asphalt fire retardant, which enhanced the compatibility between asphalt fire retardant and asphalt.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANES BY THE ADSORPTION OF NON-IONIC SURFACTANTS

Surface modification by physical adsorption of a series of non-ionic surfactants including Tween 20, Tween 40, Tween 60, Tween 80 and Tween 85, was accomplished on polypropylene microporous hollow fiber and flat membranes. The adsorption curve of the membrane surface was analyzed by weight measurements and the typical results showed a twoplatform character similarly. Differences in the degree and curve shape of adsorption resulting from such factors as concentration, temperature, as well as water cleaning time were observed for Tween 85 among other Tweens. Attenuated total reflection - Fourier transform infrared spectroscopy analysis and field emission scanning electron microscopy observation showed that the adsorption of Tween on polypropylene microporous membrane （PPMM） is effective and occurs mainly in the pores of PPMMs at low adsorption amount, and on the membrane surface also at high adsorption value.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANE BY TETHERING POLYPEPTIDES

Two kinds of polypeptides were tethered onto the surface of polypropylene microporous membrane （PPMM） through a ring opening polymerization of L-glutamate N-carboxyanhydride initiated by amino groups which were introduced by ammonia plasma and y-aminopropyl triethanoxysilane treatments. X-ray photoelectron spectroscopy （XPS）, attenuated total reflectance Fourier transform infrared spectroscopy （FT-IR/ATR）, scanning electron microscopy （SEM）, together with water contact angle measurements were used to characterize the modified membranes. XPS analyses and FT-IR/ATR spectra demonstrated that polypeptides are actually grafted onto the membrane surface. The wettability of the membrane surface increases at first and then decreases with the increase in grafting degrees of polypeptide. Platelet adhesion and murine macrophage attachment experiments reveal an enhanced hemocompatibility for the polypeptide modified PPMMs. All these results give evidence that polypeptide grafting can simultaneously improve the hemocompatibility as well as reserve the hydrophobicity for the membrane, which will provide a potential approach to improve the performance of polypropylene hollow fiber microporous membrane used in artificial oxygenator.

Preparation and surface modification of PVDF-carbon felt composite bipolar plates for vanadium flow battery

The performance of vanadium flow batteries （VFBs） is closely related to the materials used in the bipo- lar plates. Carbon-based composite bipolar plates are particularly suitable for VFB applications. However. most original preparation methods cannot simultaneously achieve good electrical conductivity and me- chanical performance. In this paper, we propose a novel approach to fabricating bipolar plates with car- bon plastic materials, including four steps, namely coating a poly （vinylidene fluoride） （PVDF） solution onto carbon felt, solvent evaporation, hot-pressing, and surface modification. The resulting bipolar plates showed high conductivity, good mechanical strength, and corrosion resistance. Surface modification by coating with carbon nanotubes （CNTs） removed the PVDF-rich layer from the surface of the carbon fibers. The high surface area of the CNT withdrew PVDF resin from the carbon fiber surface, and promoted the formation of a conductive network. The flexibility and battery charge-discharge cycle measurements showed that the composite bipolar plates can meet requirements for VFB applications.