Disturbances rejection optimization based on improved two-degree-of-freedom LADRC for permanent magnet synchronous motor systems

Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturbance suppression and have poor performance in suppressing complex nonlinear disturbances.In order to address these issues,this paper proposes an improved two-degree-of-freedom LADRC(TDOF-LADRC)strategy,which can enhance the disturbance rejection performance of the system while decoupling entirely the system's dynamic and anti-disturbance performance to boost the system robustness and simplify controller parameter tuning.PMSM models that consider total disturbances are developed to design the TDOF-LADRC speed controller accurately.Moreover,to evaluate the control performance of the TDOF-LADRC strategy,its stability is proven,and the influence of each controller parameter on the system control performance is analyzed.Based on it,a comparison is made between the disturbance observation ability and anti-disturbance performance of TDOF-LADRC and CLADRC to prove the superiority of TDOF-LADRC in rejecting disturbances.Finally,experiments are performed on a 750 W PMSM experimental platform,and the results demonstrate that the proposed TDOF-LADRC exhibits the properties of two degrees of freedom and improves the disturbance rejection performance of the PMSM system.

Permanent Magnet Axial Section Shaping Optimization Surface-mounted Permanent Magnet Synchronous Motor

In this paper, a new type of harmonic injection permanent magnet shape optimization method is proposed to suppress the torque ripple of surface-mounted permanent magnet synchronous motor. The sinusoidal waveform shaping of the axial section of the permanent magnet is added with the third harmonic shaping, and the sine wave and the third harmonic are derived. The optimal ratio is 6:1. The permanent magnet no shaping, sinusoidal shaping and sinusoidal combined third harmonic shaping are compared. The results show that the sinusoidal combined third harmonic shaping design can effectively suppress the torque ripple of the surface mounted permanent magnet synchronous motor and obtain a relatively large output torque. At the same time, a method of using permanent magnet segmentation to approximately equivalently replace sine combined with third harmonic shaping design is proposed, which effectively saves the manufacturing cost of permanent magnets and provides design and research ideas for more economical and effective optimization of surface-mounted permanent magnet motors.

Improved Particle Swarm Optimization for Parameter Identification of Permanent Magnet Synchronous Motor

In the process of identifying parameters for a permanent magnet synchronous motor,the particle swarm optimization method is prone to being stuck in local optima in the later stages of iteration,resulting in low parameter accuracy.This work proposes a fuzzy particle swarm optimization approach based on the transformation function and the filled function.This approach addresses the topic of particle swarmoptimization in parameter identification from two perspectives.Firstly,the algorithm uses a transformation function to change the form of the fitness function without changing the position of the extreme point of the fitness function,making the extreme point of the fitness function more prominent and improving the algorithm’s search ability while reducing the algorithm’s computational burden.Secondly,on the basis of themulti-loop fuzzy control systembased onmultiplemembership functions,it is merged with the filled function to improve the algorithm’s capacity to skip out of the local optimal solution.This approach can be used to identify the parameters of permanent magnet synchronous motors by sampling only the stator current,voltage,and speed data.The simulation results show that the method can effectively identify the electrical parameters of a permanent magnet synchronous motor,and it has superior global convergence performance and robustness.

Review of Field Weakening Control Strategies of Permanent Magnet Synchronous Motors

Due to high power density,high efficiency,and accurate control performance,permanent magnet synchronous motors(PMSMs)have been widely adopted in equipment manufacturing and energy transformation fields.To expand the speed range under finite DC-bus voltage,extensive research on field weakening(FW)control strategies has been conducted.This paper summarizes the major FW control strategies of PMSMs,which are categorized into calculation-based methods,voltage closed-loop control methods,and model predictive control related methods.The existing strategies are analyzed and compared according to performance,robustness,and execution difficulty,which can facilitate the implementation of FW control.

Study on the Peripheral Magnetic Leakage and Shielding Measures of Surface-mounted Permanent Magnet Motor

Permanent magnet(PM)motors are widely used in our daily lives.Taking a surface-mounted PM motor as an example,a magnetic circuit model considering the peripheral magnetic flux leakage is established.Maxwell software is used to simulate different loads and thicknesses and the materials of the shielding layers.The magnetic flux leakage around the motor has a sinusoidal distribution in the space.The value of the magnetic flux leakage is inversely proportional to the power of P+1 from the surface of the core.The thicker the shielding layer,the smaller the magnetic leakage.The greater the relative permeability of the shielding layer,the better the shielding effect.The results provide ideas and recommendations for the magnetic flux leakage analysis and the design of non-magnetic or low magnetic motors.

Influence of Magnet Shape on the Cogging Torque of a Surface-mounted Permanent Magnet Motor

The influence of bread-loaf shaped magnet poles under parallel magnetization on the cogging torque of surface-mounted permanent magnet(SPM)motors is studied.For the SPM motors having magnetic poles with eccentricity and sine harmonic compensation,the electromagnetic performances of integer and fractional slot motors are compared.It is found that the cogging torque and torque ripple of the integer and fractional slot motors can be reduced with the same eccentric magnet pole.The cogging torque and torque ripple of a fractional slot motor can be decreased by sine harmonic compensation,however,the same sine harmonic compensation has a small influence in integer slot motors.By varying the magnetic poles,the contribution of the field harmonics(k=(2n+1)p),which are a direct result of magnet magnetization,to the cogging torque also changes.The electromagnetic performance of a 3 kW prototype is tested,and it is found that the experimental results validate the theoretical investigation.

No-Load Iron Loss Model for a Fractional-Slot Surface-Mounted Permanent Magnet Motor Based on Magnetic Field Analytical Calculation

The common analytical models for the no-load iron loss of permanent magnet(PM)motors usually neglect the iron loss caused by the rotating magnetic field in the tooth tips and the harmonics of the magnetic fields in the teeth and yokes.This paper presents an analytical model for no-load iron loss of a fractional-slot surface-mounted permanent magnet motor.According to the existing analytical model of the magnetic field distribution in the slotted air gap,the magnetic flux densities considering the harmonics of the stator tooth and yoke are both derived based on the continuity of magnetic flux.Due to the complexity of the magnetic field in the tooth tip,the tangential flux density of the tooth tip is approximated by an equivalent sine wave and the radial component is regarded to be the same as that of the corresponding tooth.After obtaining the magnetic fields in stator different regions,the analytical iron loss is calculated by using the Bertotti model and the orthogonal decomposition model.A 20-pole/24-slot PM synchronous motor is taken as an example.The maximum error between the analytical model and finite element model(FEM)is 5.46%,which verifies the validity of the proposed method.

Analysis of temperature field for a surface-mounted and interior permanent magnet synchronous motor adopting magnetic-thermal coupling method

Aiming at obtaining high power density of surface-mounted and interior permanent magnet synchronous motor(SIPMSM),it is important to accurately calculate the temperature field distribution of SIPMSM,and a magnetic-thermal coupling method is proposed.The magnetic-thermal coupling mechanism is analyzed.The thermal network model and finite element model are built by this method,respectively.The effects of power frequency on iron losses and temperature fields are analyzed by the magnetic-thermal coupling finite element model under the condition of rated load,and the relationship between the load and temperature field is researched under the condition of the synchronous speed.In addition,the equivalent thermal network model is used to verify the magnetic-thermal coupling method.Then the temperatures of various nodes are obtained.The results show that there are advantages in both computational efficiency and accuracy for the proposed coupling method,which can be applied to other permanent magnet motors with complex structures.

Design and Optimization of Interior Permanent Magnet(IPM)Motor for Electric Vehicle Applications

This paper explores some design parameters of an interior permanent magnet synchronous motor that contribute to enhancing motor performance.Various geometry parameters such as magnet dimension,machine diameter,stator teeth height,and number of poles are analyzed to compare overall torque,power,and torque ripples in order to select the best design parameters and their ranges.Pyleecan,an open-source software,is used to design and optimize the motor for electric vehicle applications.Following optimization with Non-dominated Sorting Genetic Algorithm(NSGA-Ⅱ),two designs A and B were obtained for two objective functions and the corresponding torque ripples values of the design A and B were later reduced by 32%and 77%.Additionally,the impact of different magnet grades on the output performances is analyzed.

Cascaded Model Predictive Control of Six-phase Permanent Magnet Synchronous Motor with Fault Tolerant Ability

In the field of high-power electric drives, multiphase motors have the advantages of high power-density, excellent fault tolerance and control flexibility. But their decoupling control and modulation process are much more complicated compared with three-phase motors due to the increased degree of freedom. Finite control set model predictive control can reduce the difficulties of controlling six-phase motors because it does not require modulation process. In this paper, a cascaded model predictive control strategy is proposed for the optimal control of high-power six-phase permanent magnet synchronous motors. Firstly, the current prediction model of torque and harmonic subspaces are established by decoupling the six-phase spatial variables. Secondly, a cascaded cost function with fault-tolerant capability is proposed to eliminate the weighting factor in the cost function. And finally, the proposed strategy is demonstrated through theoretical analysis and experiments. It is validated that the proposed method is able to maintain excellent steady-state control accuracy and fast dynamic response while significantly reduce the control complexity of the system. Besides, it can easily achieve fault-tolerant operation under open-phase fault.

Adaptive Gain Tuning Rule for Nonlinear Sliding-mode Speed Control of Encoderless Three-phase Permanent Magnet Assisted Synchronous Motor

In this paper, an adaptive gain tuning rule is designed for the nonlinear sliding mode speed control(NSMSC) in order to enhance the dynamic performance and the robustness of the permanent magnet assisted synchronous reluctance motor(PMa-Syn RM) with considering the parameter uncertainties. A nonlinear sliding surface whose parameters are altering with time is designed at first. The proposed NSMSC can minimize the settling time without any overshoot via utilizing a low damping ratio at starting along with a high damping ratio as the output approaches the target set-point. In addition, it eliminates the problem of the singularity with the upper bound of an uncertain term that is hard to be measured practically as well as ensures a rapid convergence in finite time, through employing a simple adaptation law. Moreover, for enhancing the system efficiency throughout the constant torque region, the control system utilizes the maximum torque per ampere technique. The nonlinear sliding surface stability is assured via employing Lyapunov stability theory. Furthermore, a simple sliding mode estimator is employed for estimating the system uncertainties. The stability analysis and the experimental results indicate the effectiveness along with feasibility of the proposed speed estimation and the NSMSC approach for a 1.1-k W PMa-Syn RM under different speed references, electrical and mechanical parameters disparities, and load disturbance conditions.

Speed Regulation Method Using Genetic Algorithm for Dual Three-phase Permanent Magnet Synchronous Motors

Dual three-phase Permanent Magnet Synchronous Motor(DTP-PMSM)is a nonlinear,strongly coupled,high-order multivariable system.In today’s application scenarios,it is difficult for traditional PI controllers to meet the requirements of fast response,high accuracy and good robustness.In order to improve the performance of DTP-PMSM speed regulation system,a control strategy of PI controller based on genetic algorithm is proposed.Firstly,the basic mathematical model of DTP-PMSM is established,and the PI parameters of DTP-PMSM speed regulation system are optimized by genetic algorithm,and the modeling and simulation experiments of DTP-PMSM control system are carried out by MATLAB/SIMULINK.The simulation results show that,compared with the traditional PI control,the proposed algorithm significantly improves the performance of the control system,and the speed output overshoot of the GA-PI speed control system is smaller.The anti-interference ability is stronger,and the torque and double three-phase current output fluctuations are smaller.

Thermal analysis of surface-mounted permanent magnet synchronous motor for electric vehicle application

As a driving motor, surface mounted permanent magnet synchronous motor exhibits high efficiency and high power density. However, it is susceptible to suffer irreversible demagnetization and insulation failure of coils under severe thermal load condition. Therefore, it is essential to predict temperattrre distribution in the driving motor. In this paper, a lumped parameter thermal mode/of surface mounted permanent magnet is investigated. By using finite element method, the iron loss distribution in various parts of the driving motor is achieved. Moreover, the influences of interface gap and flow rate on temperature distribution are discussed. Finally, the simulation of temperature distribution in different parts of the driving motor is achieved. The presented methodology contributes to verify the feasibility of the driving motor design.

Research on Thermal Calculation and End Winding Heat Conduction Optimization of Low Speed High Torque Permanent Magnet Synchronous Motor

Because of its simple structure,large torque and high efficiency,permanent magnet synchronous motor of low speed and high torque is widely adopted in many fields.In this paper,a 394.5k W mining low-speed high-torque permanent magnet synchronous motor(LSHTPMSM)is regarded as the study object.According to the physical model,a three-dimensional equivalent heat transfer temperature field calculation model of the motor is built to simulate the temperature distribution of the motor under rated conditions.In terms of the serious issue of stator winding temperature increase of permanent magnet synchronous motor of low speed and high torque,the heat conduction optimization of the end of the stator winding is studied,which enhances the heat dissipation effect of the stator end winding,effectively reduces its temperature increase and temperature gradient with the winding in the slot,and improves the practical efficiency and service life of the motor.Finally,the motor temperature rise test platform is constructed for the verification of the feasibility of the optimization scheme,which provides a reference direction for the heat dissipation optimization of permanent magnet synchronous motor of low speed and high torque.

Permanent Magnet Assisted Synchronous Reluctance Motor with Asymmetric Rotor for High Torque Performance

Permanent magnet assisted synchronous reluctance motor(PMA-SynRM)is a kind of high torque density energy conversion device widely used in modern industry.In this paper,based on the basic topology of PMA-SynRM,a novel PMA-SynRM of asymmetric rotor with position-biased magnet is proposed.The asymmetric rotor design with position-biased magnet realizes the concentration of magnetic field lines in the motor air gap to obtain higher electromagnetic torque,and makes both of magnetic and reluctance torque obtain the peak value at the same current phase angle.The asymmetric rotor configuration is theoretically illustrated by space vector diagram,and the feasibility of high torque performance of the motor is verified.Through the finite element simulation,the effect of the side barrier on output torque and the Mises stress under the rotor asymmetrical design are analyzed.Then the motor characteristics including airgap flux density,back EMF,magnetic torque,reluctance torque,torque ripple,losses,and efficiency are calculated for both the basic and proposed PMA-SynRMs.The results show that the proposed PMA-SynRM has higher torque and efficiency than the basic topology.Moreover,the torque ripple of the proposed PMA-SynRM is reduced by the method with harmonic current injection,and the torque characteristics in the whole current cycle are analyzed.Finally,the endurance to avoid PM demagnetization is confirmed based on the PM remanence calculation.

Design of Rotor Magnetic Barrier Structure of Built-in Permanent Magnet Motor Based on Taguchi Method

In this paper,a 20kW vehicle built-in permanent magnet synchronous motor is taken as an example,and a magnetic barrier structure is added to the rotor of the motor to solve the uneven saturation problem of the rotor side magnetic bridge.This structure improves the air-gap flux density waveform of the motor by influencing the internal magnetic flux path of the motor rotor,thus improving the sine of the no-load back EMF waveform of the motor and reducing the torque ripple of the motor.At the same time,Taguchi method is used to optimize the structural parameters of the added magnetic barrier.In order to facilitate the analysis of its uneven saturation phenomenon and improve the optimization effect,a simple equivalent magnetic network(EMN)model considering the uneven saturation of rotor magnetic bridge is established in this paper,and the initial values of optimization factors are selected based on this model.Finally,the no-load back EMF waveform distortion rate,torque ripple and output torque of the optimized motor are compared and analyzed,and the influence of magnetic barrier structure parameters on the electromagnetic performance of the motor is also analyzed.The results show that the optimized motor can not change the output torque of the motor as much as possible on the basis of reducing the waveform distortion rate of no-load back EMF and torque ripple.

Torque Improvement of Spoke-type Permanent Magnet Motor with Auxiliary Stator Using Harmonic Current Control Strategy

The spoke-type permanent magnet motor with auxiliary stator exhibits high torque performance owing to the flux focus effects.To further improve its torque density,this paper proposes a control method by using harmonic current strategy.Based on the theoretical analysis,a 3-D torque look-up table by dq-axis current and electrical angle is established with the aid of the finite element method(FEM).The maximum torque per ampere curve at each rotor position is identified and summarized to adequately indicate the relationship between torque and current amplitude of the motor.Through theoretical derivation,it is concluded that the minimum torque cost curve is the contour line of?Te/?i2,which can be employed to identify the harmonic current for torque density improvement.Compared to traditional strategies,the proposed control strategy can increase torque density of forward and reverse torque by 1.22%and 1.40%,respectively.The experimental results verify the analysis and simulation results,as well as prove the effectiveness of the proposed strategy.

Integrated Sliding Mode Velocity Control of Linear Permanent Magnet Synchronous Motor with Thrust Ripple Compensation

In this paper,a compound sliding mode velocity control scheme with a new exponential reaching law(NERL)with thrust ripple observation strategy is proposed to obtain a high performance velocity loop of the linear permanent magnet synchronous motor(LPMSM)control system.A sliding mode velocity controller based on NERL is firstly discussed to restrain chattering of the conventional exponential reaching law(CERL).Furthermore,the unavoidable thrust ripple caused by the special structure of linear motor will bring about velocity fluctuation and reduced control performance.Thus,a thrust ripple compensation strategy on the basis of extend Kalman filter(EKF)theory is proposed.The estimated thrust ripple will be introduced into the sliding mode velocity controller to optimize the control accuracy and robustness.The effectiveness of the proposal is validated with experimental results.

Characteristic Analysis and Experimental Study of a Hybrid Permanent Magnet Variable Flux Memory Motor

提出一种混合永磁可变磁通记忆电机，研究了永磁体不同磁化状态下的静态特性。基于有限元法，对施加不同去磁电流时的电机磁场分布进行了分析，并观察永磁体内的磁密变化，计算了不同永磁磁化状态下的气隙磁密、永磁磁链、反电动势及每极气隙磁通等电机主要参数。制作一台样机，并进行实验研究，实验结果与有限元计算结果吻合较好。研究表明，永磁体的充磁比去磁要困难，当磁化电流为2倍的定子额定电流时，能将磁体去磁90％，而仅能充磁到饱和时的30％：与基本结构记忆电机相比，该混合永磁记忆电机具有更高的气隙磁密。该类电机在宽调速驱动系统中具有应用前景。

Development of the High-performance Synchronous Permanent Magnet Planar Motor and Its Key Technologies

永磁同步平面电机具有直接驱动、出力密度高、低热耗、高精度等特点,在现代精密、超精密加工装备,特别是在极紫外光刻机中具有广阔的应用前景。根据永磁阵列和线圈阵列的结构形式将永磁同步平面电机划分为组合式、半组合式、绕组层叠式和对称式永磁同步平面电机4类,并介绍了各种类型平面电机的特点,总结了永磁同步平面电机关键技术的发展现状,针对目前永磁同步平面电机存在的不足,讨论了未来永磁同步平面电机发展的趋势与方向。