Stress and noises of steel box girders in Sutong Bridge

Sutong Bridge is a cable-stayed bridge with a main span of 1 088 m. 370 high-precision stress monitoring measured data show that in the process of hoisting the steel box girders,the stress of the main girders is in the fluctuant and complex state and many meteorological factors,such as sunshine radiation,temperature and wind,have important influence on the change of stress of the steel box girders. According to the real-time weather data,the stress data after the process of wavelet denoising from representative measuring points in different weather conditions is picked to establish the stress response brought by meteorological factors with Layered Separation method,thereby basically eliminating the influence of meteorological factors on the stress of main girders,so that accurate and reliable stress data can be got for steel box girders adjustment and cable-tensioned construction control.

The study of temperature effects on steel box girder for Taizhou Bridge

Using the temperature gradient which was proposed by continuously measuring flat steel box girder of Runyang Bridge, temperature effects of flat steel box girder were studied for Taizhou Bridge. With three temperature gradient models (JTG D60-2004 specification, BS5400 specification and the temperature gradient which was proposed in this paper), the stress of control sections was calculated by finite element program ANSYS. The calculated result indicated that the temperature gradient that was put forward in JTG D60-2004 specification and BS5400 specification for calculating the stress of flat steel box girder was not suitable to apply to flat steel box girder. The temperature gradient on flat steel box girder which was proposed in this paper was reasonable.

Study in the design and manufacture process of the elastic cable anchor box in steel box girder of Taizhou Bridge

Taizhou Yangtze River Highway Bridge is a large span suspension bridge with three pylons. The elastic cables are installed to connect the steel tower and the steel box girder. The constraints can increase the safety coefficient of the middle saddle, and improve the stress conditions of the middle pylon and decrease the deflection in the middle of the main girder, as well as the longitudinal displacement of the main girder caused by live loads. The anchorage boxes of the elastic cable are installed in the wind fairing outside the vertical web plate of the box girder. Two anchor boxes form a pair and are arranged parallelly. Eight anchor boxes are installed in the bridge. In this paper, the design scheme and the technical difficulties in manufacturing are briefly discussed with the precision control techniques.

Design of steel box girder for Taizhou Yangtze River Highway Bridge

Taizhou Yangtze River Highway Bridge is the first three-pylon two-span suspension bridge in China. The main girder adopts flat steamline steel closed box girder which has well wind-resistant capability and is technically mature besides beautiful appearance. Straight web plates of the steel box girder in longitudinal direction are proposed in order to ensure the integrity of the steel box girder, and to keep the stress of the steel box girder continuous in the middle pylon, as well as to reduce the gradient of the middle pylon columns. The cross section of the box girder has one box with three cells. Solid-web diaphragm plate with good integrity and high torsional stiffness is adopted. The lifting lugs are utilized in the anchors of suspender cable. In this paper, selection of the cross section of the steel box girder, the general structure design, local structure design and main structure calculation results of Taizhou Yangtze River Bridge are introduced emphatically.

Research on overall assembling and welding process of steel box girder tuyere blocks of Taizhou Bridge

This article presents in detail the assembling and welding process technique of the steel box girder tuyere blocks of Taizhou Bridge. The application of this process technique effectively solves the problem of welding stress release in tuyere block assembling and welding without increasing the number of turns of the blocks and overhead welding, thus avoiding possible structural deformation due to excessive accumulation of internal welding stress, greatly reducing the repeated deformation and correction work during assembling and welding, and ensuring the weld seam quality and overall dimensions of tuyere blocks of Taizhou Bridge.

Estimating extreme temperature differences in steel box girder using long-term measurement data

The extreme temperature differences in flat steel box girder of a cable-stayed bridge were studied.Firstly,by using the long-term measurement data collected by the structural health monitoring system installed on the Runyang Cable-stayed Bridge,the daily variations as well as seasonal ones of measured temperature differences in the box girder cross-section area were summarized.The probability distribution models of temperature differences were further established and the extreme temperature differences were estimated with a return period of 100 years.Finally,the temperature difference models in cross-section area were proposed for bridge thermal design.The results show that horizontal temperature differences in top plate and vertical temperature differences between top plate and bottom plate are considerable.All the positive and negative temperature differences can be described by the weighted sum of two Weibull distributions.The maximum positive and negative horizontal temperature differences in top plate are 10.30°C and13.80°C,respectively.And the maximum positive and negative vertical temperature differences between top plate and bottom plate are 17.30°C and 3.70°C,respectively.For bridge thermal design,there are two vertical temperature difference models between top plate and bottom plate,and six horizontal temperature difference models in top plate.

南京仙新路长江大桥主桥结构设计

南京仙新路长江大桥主桥为跨径1760 m的单跨钢箱梁悬索桥,主缆垂跨比1/9,边跨跨径580 m,边中跨比0.33。该桥上、下游各设1根主缆,单根主缆由169股127∅5.4 mm镀锌铝高强钢丝索股组成,采用PPWS法施工,钢丝标准抗拉强度2100 MPa。吊索与索夹采用销接式结构,跨中设置柔性中央扣索,短吊索设置关节轴承。主索鞍采用宽鞍槽单纵肋铸焊结合构造,散索鞍采用底座式全铸结构。加劲梁采用扁平流线型封闭整体钢箱梁,总宽31.5 m,梁高4 m,顶板与U肋之间采用双面埋弧全熔透焊接。桥塔采用门形混凝土结构,总高277.3 m,其上横梁为预应力混凝土结构,外包N字造型钢结构;桥塔基础采用直径2.8 m钻孔灌注桩。南锚碇采用外径65 m圆形地下连续墙基础;北锚碇采用沉井基础,平面尺寸70 m×50 m,高50 m。对结构进行静力分析及抗风性能理论和试验研究,结果表明:结构强度、刚度均满足规范要求;在加劲梁上设置0.67 m高中央稳定板、两侧风嘴处设置1 m宽水平稳定板后,大桥的颤振、涡振等抗风性能均满足要求,且具备一定的阻尼储备。

公铁合建钢混板-桁斜拉桥悬挑式钢锚箱受力特性及结构优化

为研究大跨度公铁合建钢混板-桁斜拉桥主梁悬挑式索梁钢锚箱结构的受力特性及结构优化,以主跨808 m的洪奇沥特大桥钢锚箱为背景,采用仿真分析方法,研究钢锚箱3个设计方案主要板件应力、焊缝应力以及推荐方案锚箱节点的传力特性和锚箱参数对钢锚箱受力的影响。结果表明:锚箱尺寸较大、顶底板加肋方案的主要板件应力最大为300 MPa,小于其他2种方案,且6条焊缝的最大应力和应力不均匀系数较优,因此确定该方案为最终设计方案;索力首先由锚垫板直接向钢锚箱顶、底板和内外腹板较为均匀传递,最终边弦杆底板、内腹板和外腹板分别承担了22.2%,46.4%和31.4%的索力;节点处副桁斜杆、近桥塔侧和远桥塔侧边弦杆、混凝土桥面、节点横梁分别传递约66.71%,9.72%,9.32%,9.68%和4.56%的斜拉索竖向分力;板件应力随顶底板厚度增加而减小,顶底板深入边弦杆长度增加可以降低底板-内腹板焊缝峰值应力,顶底板间距减小可降低内外腹板和顶底板与锚垫板接触区域应力;顶底板厚44 mm、锚箱顶底板深入边弦杆长度1800 mm、顶底板间距660 mm时较为合理。

大跨度钢-混结合梁悬索桥涡激振动控制指标体系研究

为保证已建桥梁发生涡激振动后桥梁结构的安全以及桥上行车和行人安全,提出综合考虑人员舒适性、结构受力和停车线形三方面的大跨度钢-混结合梁悬索桥涡激振动控制指标体系。该体系包含9项指标,分别为驾乘人员舒适度、驾乘人员晕动症、行人舒适度(狄克曼指标)、加劲梁强度、加劲梁应力、加劲梁挠度、桥面纵坡、竖曲线半径和停车视距。以武汉鹦鹉洲长江大桥为背景,分别计算了“限速”和“封桥”2个交通管制措施下9项指标对应的涡激振动振幅限值。在此基础上,将9项指标对应的涡激振动振幅限值的最小值作为涡激振动限值建议取值。结果表明:当该桥发生低阶竖弯涡激振动(VS1、VAS1)时,涡激振动的控制因素为加劲梁挠度指标;当大桥发生VAS2模态的竖弯涡激振动时,涡激振动由驾乘人员晕动症指标和行人舒适度指标共同控制;当大桥发生高阶竖弯涡激振动(VAS3、VAS4)时,涡激振动由行人舒适度指标控制。涡激振动控制指标体系及限值标准的计算框架可适用于不同桥型涡激振动限值的计算。

大跨度铁路桥附属构件对不同宽高比矩形断面涡振性能的影响

在已建成的大跨度鳊鱼洲长江大桥原设计宽高比为6.7∶1的四线铁路桥矩形箱型主梁断面的基础上,通过调整断面宽高比,设计宽高比为4∶1的二线铁路和宽高比为9∶1的六线铁路桥矩形箱梁断面。通过节段模型风洞试验,在0°,±3°和±5°风攻角的均匀来流下,对以上3种常用二线、四线和六线铁路桥矩形箱梁断面与对应相同宽高比纯矩形断面之间的涡振特性关系,以及铁路桥附属构件对不同宽高比矩形断面涡振性能的影响进行研究。结果表明:在宽高比分别为4∶1和6.7∶1的矩形断面上布置铁路桥附属构件能增大断面在负风攻角下的涡振振幅,在-5°风攻角下竖向涡振振幅增大率高达277.5%,但对正风攻角下的涡振响应起到一定的抑制作用,而在宽高比为9∶1的矩形断面布置六线铁路桥附属构件则能明显增大该断面在各风攻角下的涡振振幅,其扭转涡振振幅增大率均在48.3%以上;铁路桥附属构件对矩形断面涡振性能的降低作用随着断面宽高比的增大而提升,针对气动外形较钝的二线和四线铁路桥箱梁,可参考相似宽高比矩形断面涡振特性,并重点考察箱梁在负风攻角下的涡振响应,而针对宽高比较大的六线铁路桥箱梁,由于附属构件影响较大,参考相似宽高比矩形断面涡振特性的意义较小,均应详细研究其在各风攻角下的涡振性能。

武汉青山长江公路大桥宽幅钢箱梁悬臂拼装横向线形匹配技术

武汉青山长江公路大桥主桥为主跨938 m的双塔双索面全飘浮体系斜拉桥,主跨整体式钢箱梁高4.5 m、全宽48 m,采用500 t架梁吊机分节段悬臂拼装架设。钢箱梁悬臂拼装时,架梁吊机站位节段、待架节段由于荷载及约束不同,横截面变形呈现出不同的趋势,线形匹配难度大。为解决该问题,主跨钢箱梁悬臂拼装时选择上、下游分体式架梁吊机,减少架梁吊机自重;经比选选择横桥向27.7 m间距的架梁吊机站位,减小了架梁吊机荷载对横向线形匹配的影响;通过设置顶压装置(由顶压牛腿、支承底座组成),在架梁吊机站位节段、待架节段钢箱梁边腹板处施加1500 kN顶压力,配合少量马板,一次加载完成对接口竖向变形匹配调整。施工后,钢箱梁横向线形匹配精度均满足要求。

简支波形腹板钢箱组合截面与传统截面箱梁桥抗震性能对比分析

为研究波形腹板钢箱-混凝土组合梁桥(CW-SBCCGB)与传统箱梁桥抗震性能的异同,基于截面等效原理,根据某实际工程CW-SBCCGB的单箱截面,等效出波形腹板混凝土箱梁桥(CW-CBGB)和混凝土箱梁桥(CBGB)的单箱截面,再结合动力分析理论和ABAQUS有限元模型对比分析3种截面简支梁桥动力特性和抗震性能的不同。结果表明:3种截面简支梁桥前五阶振型不变,CW-CBGB和CBGB前三阶频率相比于CW-SBCCGB有所下降,但相差不超过1Hz,第四阶及以后频率差异逐渐变大;剪滞效应对CW-SBCCGB和CW-CBGB动力特性影响较大,对CBGB影响较小;在纵桥向+竖桥向和横桥向+竖桥向地震作用下,CW-SBCCGB和CBGB的墩顶位移和跨中位移均大于CW-CBGB结构,CW-SBCCGB主梁跨中截面剪力最小,CW-CBGB跨中截面弯矩最小,说明CW-SBCCGB和CW-CBGB的抗震性能均优于CBGB的抗震性能。

开口断面钢-混结合梁悬索桥颤振特性及颤振形态研究

为准确评估开口断面双边箱钢-混结合梁悬索桥颤振性能和多模态参与效应,以典型的钢-混结合梁悬索桥——怀化洞庭溪沅水特大桥为背景,开展风洞模型试验及数值分析。制作加劲梁节段缩尺模型并进行风洞试验,测试原桥梁结构的颤振性能,分析调整阻尼比、采用气动措施及结构措施对结构颤振特性的影响,采用三维和二维两种颤振分析方法分析设置中央扣结构的颤振模态及多模态参与效应。结果表明:该钢-混结合梁悬索桥存在较明显的颤振起振点,且颤振是以扭转为主的弯扭耦合振动,同时其扭转和竖向振动存在较大的相位差(相差近180°);节段模型风洞试验与三维和二维颤振分析一致得到设置中央扣后,频率较高的正对称扭转模态先于反对称模态发生颤振,且三维与二维颤振分析结果相差不大。

槽形钢箱梁涡振性能及抑振措施试验研究

为提高槽形钢箱梁桥的抗风性能,对槽形钢箱梁的涡振性能及抑振措施进行试验研究。以某人行景观桥槽形钢箱梁为背景,通过主梁节段模型风洞试验,研究+3°、0°、-3°风攻角下均匀流与紊流风场中槽形钢箱梁的涡振性能,分析交替封闭栏杆、将栏杆楔形扶手改为圆形扶手、提高阻尼比等措施的抑振效果。结果表明:原槽形钢箱梁断面涡振性能不满足规范要求,均匀流风场中,3个风攻角下均出现了超限的竖弯涡振,+3°和-3°风攻角下出现了不同程度的扭转涡振,最不利风攻角为-3°;紊流风场中,最不利风攻角下原断面竖弯涡振振幅降低了23%,未见明显扭转涡振;楔形扶手栏杆交替封闭使结构竖弯涡振振幅增大,主梁涡振性能降低;单独改变栏杆扶手形状为圆形对主梁涡振性能影响不大,在此基础上交替封闭栏杆能够有效抑制主梁涡振;提高结构阻尼比能有效抑制主梁涡振,阻尼比为7‰时,主梁竖弯涡振振幅可降至规范限值的一半左右。

远场爆炸荷载作用下钢箱梁桥的动力响应及毁伤评估

针对大规模爆炸后桥梁结构的毁伤评估问题,以三跨连续钢箱梁为对象,采用计算流体动力学(Computational Fluid Dynamics,CFD)和显式动力学方法,研究了冲击波入射角度与冲击波强度对桥梁结构破坏模式的影响规律,建立了桥梁毁伤程度与冲击波特性之间的映射关系。结果表明:通过CFD数值模拟得到的爆炸荷载可以反映冲击波的绕射和消波效应,可以为桥梁结构的抗爆计算提供可靠的爆炸荷载;桥梁的破坏模式与冲击波入射角有关,而桥梁的毁伤程度与冲击波强度有关;入射角度为0°时,桥梁的迎爆面腹板发生局部屈曲,非迎爆面桥墩发生破坏。

大跨PK断面钢箱梁斜拉桥涡振性能及优化措施研究

红莲大桥主桥为主跨580 m的双塔斜拉桥,中跨主梁采用PK断面钢箱梁,该类主梁断面易发生涡振,需对其涡振性能及抑振措施进行研究。基于该桥有限元动力特性分析结果,制作PK断面钢箱梁1∶60缩尺比节段模型进行测振风洞试验,研究桥梁原始设计断面主梁的涡振性能,讨论增加结构阻尼比(增加至0.010和0.027)措施的涡振抑振效果,并对增设稳定板、水平导流板、部分封闭桥面栏杆等不同气动优化措施及组合对主梁涡振性能的影响进行分析。结果表明:原始设计PK断面钢箱梁的涡振振幅明显超过规范限值;增大结构阻尼比虽然可以有效抑制涡振响应,但阻尼比增加至0.027时竖弯涡振振幅仍然显著;在桥面检修栏杆上缘外挑1.6 m宽水平导流板可将涡振振幅降低到可忽略的水平;采用在检修栏杆上缘外挑1.1 m宽水平导流板、优化桥面燃气管道位置、调整防撞护栏下部封闭高度为0.42 m,或移除检修道栏杆底座、错列布置封闭检修道栏杆和防撞护栏等组合措施,虽不足以完全抑制涡振的发生,但可将涡振振幅控制至明显小于规范限值。

公铁混合布置大跨度斜拉桥主梁断面形式研究--以赣江公铁大桥西支主桥设计为例

以赣江公铁两用大桥西支主桥设计为例,研究一种适应上层8车道公路、下层对称双线铁路+4车道公路混合布置的主梁断面形式。提出带挑臂双索面箱桁组合断面、带挑臂单索面箱桁组合断面、矩形箱桁组合断面、矩形钢桁梁断面4种主梁断面方案,采用有限元软件分析各方案静动力性能及受力特点,综合考虑方案构造特点、技术指标、工程数量、公铁运营安全、景观效果等,确定该桥选用带挑臂双索面箱桁组合断面。该桥斜拉索最大索力16000 kN,锚固在下层钢箱梁两侧,通过有限元实体分析对锚拉板和钢锚箱式两种索梁锚固形式进行比选研究,钢锚箱形式受力合理、应力水平低、经济性好,设计采用钢锚箱形式。带挑臂双索面箱桁组合断面桥面空间布置合理、下层公铁行车干扰小、梁端竖向变形最小、经济性好,是一种适应公铁混合布置大跨度斜拉桥主梁断面形式。

中低速磁浮圆曲线钢箱梁桥车致振动响应研究

随着圆曲线钢箱梁桥在城市交通中的应用愈发广泛,为探究其在中低速磁浮车辆运行作用下的振动响应特性,基于多体动力学和有限元方法建立车辆-轨道-钢箱梁刚柔耦合动力学模型,采用动态电磁阻尼力影响的二维磁轨关系,并考虑轨道关键部件的参振作用,分析圆曲线段钢箱梁的振动特性,探讨钢箱梁板厚、车辆速度及车体质量对钢箱梁振动响应的影响。结果表明:受曲率影响,钢箱梁在发生弯曲的同时亦会伴生扭转,产生弯扭耦合振动;钢箱梁的振动主要由10~20 Hz的钢箱梁整体弯曲振动、30~40 Hz的钢箱梁扭转振动以及50~70 Hz的轨道局部振动引起;计算得到的钢箱梁跨中横向及垂向最大挠度分别为1.26 mm、3.88 mm,均满足相关标准要求,钢箱梁具有足够的支撑刚度;各工况下的垂向加速度均未超过5.0 m/s^(2)的限值,且最高达到2.2 m/s^(2);在板厚10 mm以及超员载荷工况下,横向加速度大多超过1.4 m/s^(2)的限值,且最高达到4.0 m/s^(2);车辆速度的减小和车体质量的增加均会放大弯扭耦合作用影响,而板厚的增加则能够有效降低弯扭耦合作用影响,当板厚由10 mm增至40 mm时,一阶横弯及扭转频率对应振幅分别减小94.3%、98.7%。

西十高铁汉江特大桥主桥设计

西十高铁汉江特大桥主桥为主跨420 m的梁桁组合结构双塔斜拉桥,采用半飘浮体系。主梁采用钢桁加劲PC箱梁,梁高3.0 m,桥面全宽17 m。PC箱梁采用C55混凝土,单箱四室等高截面,加劲桁采用渐变三角桁式,材质为Q370qE钢,桁高9.4 m。斜拉索采用标准抗拉强度1770 MPa的镀锌平行钢丝,双索面扇形布置。桥塔采用花瓶式钢筋混凝土框架结构,塔高186.5 m,基础采用∅3 m的钻孔灌注桩,按长短桩设计。结构受力分析结果表明:该桥力学性能指标均满足相关规范要求,整体刚度性能优越,具有良好的颤振稳定性,设置的风嘴能有效抑制涡激振动,采取加劲钢桁上弦杆灌注混凝土、延迟铺轨时间等措施能有效控制主梁的收缩徐变,桥面线形满足铺设无砟轨道的要求。