Prediction of atomization characteristics of pressure swirl nozzle with different structures

The structure of the pressure swirl nozzle is an important factor affecting its spray performance.This work aims to study pressure swirl nozzles with different structures by experiment and simulation.In the experiment,10 nozzles with different structures are designed to comprehensively cover various geometric factors.In terms of simulation,steady-state simulation with less computational complexity is used to study the flow inside the nozzle.The results show that the diameter of the inlet and outlet,the direction of the inlet,the diameter of the swirl chamber,and the height of the swirl chamber all affect the atomization performance,and the diameter of the inlet and outlet has a greater impact.It is found that under the same flow rate and pressure,the geometric differences do have a significant impact on the atomization characteristics,such as spray angle and SMD(Sauter mean diameter).Specific nozzle structures can be customized according to the actual needs.Data analysis shows that the spray angle is related to the swirl number,and the SMD is related to turbulent kinetic energy.Through data fitting,the equations for predicting the spray angle and the SMD are obtained.The error range of the fitting equation for the prediction of spray angle and SMD is within 15% and 10% respectively.The prediction is expected to be used in engineering to estimate the spray performance at the beginning of a real project.

EXPERIMENTAL STUDY ON THE MACRO-AND MICRO- CHARACTERISTICS OF THE SPRAY FROM A PRESSURE SWIRL NOZZLE

The experimental study on the macro and micro characteristics of the spray from a pressure swirl nozzle embraces the growth of surface unstable wave,disintegration process,spray angle,breakup length and so on.The effects of injection pressure,nozzle geometry and liquid properties on these characteristics are also discussed.The results are helpful to understand the underlying physics of the pressure swirl nozzle and serve as the basis for the practical design,usage and improvement of the nozzle.

Flow field, heat transfer and inclusion behavior in a round bloom mold under effect of a swirling flow submerged entry nozzle

Flow field,heat transfer and inclusion behavior in a 700 mm round bloom mold under the effect of a swirling flow submerged entry nozzle(SEN)were investigated with the aim to enhance the casting process.The results indicate that the impinging flow phenomenon,which is commonly observed in conventional single-port SEN casting,was completely suppressed by the swirling flow SEN coming from a novel swirling flow generator design in tundish.Steel from the SEN port moved towards the mold wall in 360 direction,leading to a uniform temperature distribution in the mold.Compared to a conventional single-port SEN casting,the steel super-heat was decreased by about 5 K at the mold center,and the temperature was increased by around 3.5 K near the meniscus.In addition,the removal ratio of inclusions to the mold top surface in the swirling flow SEN casting was found to be increased.Specifically,the removal ratio of spherical inclusions with diameters of 1,10,50 and 100μm was increased by 18.2%,18.5%,22.6% and 42.7%,respectively.Furthermore,the ratio was raised by 18.2%,20.8%,21.5% and 44.1%for non-spherical inclusions,respectively.

Experimental investigation on the spray characteristics of agricultural full-cone pressure swirl nozzle

The spray characteristics of a full-cone pressure swirl nozzle have been investigated in this study.The results were defined by Reynolds number,which focuses on the breakup of liquid film,droplet size,velocity,and liquid volume flux under different Reynolds numbers at the near-field spray.The spray structure was visualized using a high-speed camera,and the characteristics of droplets were measured using a Phase Doppler Anemometer(PDA)in both the radial and axial directions.The tests were carried out at varying spray pressures(0.2 to 1.0 MPa),corresponding to different Reynolds numbers(5369 to 12006).It was found that when the Reynolds number rises,the liquid became more unstable after leaving the nozzle,causing the liquid film to break up faster.According to the measurements of PDA,the coalescence of droplets increased due to the centrifugal effect.What’s more,the velocity of the droplets fluctuates significantly in the radial direction,and the droplets with a smaller particle size had a higher average velocity.From the perspective of liquid distribution,the increase in Reynolds number caused the spray liquid to move in the radial direction gradually.In contrast,the liquid volume distribution changed in the radial direction more obviously than in the axial direction,growing to the maximum along the radial direction and gradually reducing.It can provide a reference for selecting operating parameters for actual agricultural spray operations and the design of electrostatic nozzles through the research on breakup and droplet characteristics.

Thermal shock resistant 3D printed ceramics reinforced with MgAl_(2)O_(4) shell structure

The demand for the swirl nozzle with enhanced temperature resistance and lightweight properties is in-creasing as the thrust-to-weight ratio of aero-engines rises.The Al_(2)O_(3) ceramic swirl nozzle can maintain high strength in a hostile environment of high temperature and severe corrosion,while also meeting the requirements of aircraft to enhance efficiency and decrease weight.However,Al_(2)O_(3) ceramics are limited in their application for aerospace components due to their poor thermal shock resistance(TSR)stemming from their inherent brittleness.This work reported an innovative design and fabrication strategy based on photopolymerization 3D printing technology to realize the three-dimensional shell structure through element interdiffusion and nanoscale stacking of the reinforced phase.With this strategy,a novel type of the new dual-structure Al_(2)O_(3) ceramic composed of MgAl_(2)O_(4) shell structure and matrix could be con-structed in situ.The nano-sized MgAl_(2)O_(4) caused a crack passivation effect after the thermal shock,which could improve the strength and TSR of 3D-printed Al_(2)O_(3) ceramic.In addition,the effects of MgO content and sintering temperature on sintering behavior,flexural strength,porosity,and TSR of Al_(2)O_(3) ceram-ics manufactured by digital light processing(DLP)processing were systematically studied.The optimum overall performance of Al_(2)O_(3) ceramics was obtained at the sintering temperature of 1550℃and the MgO content of 1.0 wt.%,with a maximum flexural strength of 111.929 MPa and a critical temperature difference of 374.24℃for TSR.Based on the above research,an aero-engine swirl nozzle with high ther-mal shock resistance has been successfully prepared by ceramic 3D printing technology,which enhances high-temperature resistance and promotes lightweight design in aero-engine.