Characteristic Analysis and Experimental Study of a Hybrid Permanent Magnet Variable Flux Memory Motor

提出一种混合永磁可变磁通记忆电机，研究了永磁体不同磁化状态下的静态特性。基于有限元法，对施加不同去磁电流时的电机磁场分布进行了分析，并观察永磁体内的磁密变化，计算了不同永磁磁化状态下的气隙磁密、永磁磁链、反电动势及每极气隙磁通等电机主要参数。制作一台样机，并进行实验研究，实验结果与有限元计算结果吻合较好。研究表明，永磁体的充磁比去磁要困难，当磁化电流为2倍的定子额定电流时，能将磁体去磁90％，而仅能充磁到饱和时的30％：与基本结构记忆电机相比，该混合永磁记忆电机具有更高的气隙磁密。该类电机在宽调速驱动系统中具有应用前景。

Initial Rotor Position Detection of 12/10 Flux-switching Permanent Magnet Motors

电机转子初始位置检测的精度直接决定其启动运行时的性能。针对12/10极永磁磁通切换型电机,在验证其凸极性的基础上,采用注入脉振高频信号实现转子初始位置估计。通过对传统高频脉振正弦电压信号注入的分析,研究了基于高频方波或三角波的注入方法,再利用电流差值调制或直接信号调制方法得到位置误差信号,同时根据磁路的饱和效应,通过对d轴电流过零点时间差值的累加,实现了磁极方向辨识。分析了位置误差信号的系数与初始位置检测收敛性的关系。通过实验验证了所提方法的正确性和可行性。

Novel Switched Flux Permanent Magnet Machine Topologies

This paper overviews various switched flux permanent magnet machines and their design and performance features,with particular emphasis on machine topologies with reduced magnet usage or without using magnet,as well as with variable flux capability.

Direct Torque and Adaptive Flux Sensorless Control of Novel Transverse Flux Permanent Magnet Motors

横向磁通永磁电机在开环无刷直流驱动模式下不可避免存在转矩脉动,但可以通过采用直接转矩控制加以改善。首先分析无刷直流驱动中＂花瓣＂状定子磁链轨迹的形成机理,然后针对传统转矩和磁链双闭环直接转矩控制中的定子磁链给定难的问题,提出了无位置传感器磁链自适应直接转矩控制方案。该方案仅利用定子磁链位置和转矩滞环比较器决定电压矢量,并配合换相补偿以修正定、转子磁链夹角与最佳提前换相角之间的偏差以兼顾高转矩电流比和低转矩脉动。仿真和实验结果证实了该方案的有效性和可行性。

An Improved Stator Flux Observation Method of Permanent Magnet Synchronous Motor

The stator flux and electromagnetic torque observation is the basis of direct torque controlled permanent magnet synchronous motor( PMSM) drive system. However,the traditional stator flux observer based on voltage model is affected by integral initial values and integral drift,that based on current model is affected by the parameters of PMSM,so a new stator flux observation method is proposed based on an improved secondorder generalized integrator( SOGI). Compared to the stator flux observation method based on the conventional SOGI,the proposed method can not only overcome the influence of integral initial values and integral drift,but also completely eliminate the DC offset's influence. Therefore,the observation accuracy of stator flux is further improved. The simulation and experimental results both show that the proposed method has a higher stator flux and electromagnetic torque observation precision.

Model predictive flux control of permanent magnet synchronous motor driven by three-level inverter based on fine-division strategy

Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model predictive flux control(MPFC)method is proposed.First,establish a mathematical model between the motor torque and the stator flux linkage according to the mathematical equations of PMSM.Thus,the control of the motor torque and stator flux linkage in the MPTC is transformed into the control of a single stator flux linkage vector,omitting the cumbersome weight setting process in the traditional MPTC.The midpoint potential control strategy is proposed,which uses the characteristics of redundant small vectors to balance the midpoint potential.After that,a fine-division strategy is proposed,which effectively reduces the number of candidate vectors and the computational burden of the system.Finally,the proposed MPFC is compared with MPTC by simulation.The results show that the proposed fine-division MPFC effectively reduces the system calculation,and has the advantages of simple principle and better dynamic and steady-state control performance.The feasibility of the control strategy is verified.

Influence of Inner/Outer Stator Pole Ratio and Relative Position on Electromagnetic Performance of Partitioned Stator Switched Flux Permanent Magnet Machines

Based on the 6-pole outer stator(armature winding-stator),the influence of inner(permanent magnet-stator)/outer stator pole ratio n(n=NIS/NOS),stator relative positions and rotor pole number combinations on electromagnetic performance of partitioned stator switched flux permanent magnet(PM)machines(PS-SFPMMs)is investigated in this paper.Since the armature windings and PMs are located in two separated stators and PMs are stationary,PS-SFPMMs have high fault tolerance capabilities.To maximize the torque performance,the PM of inner stator pole should be aligned with outer stator pole when n is odd while the iron rib of inner stator pole should be aligned with outer stator pole when n is even.No matter what n is selected,the rotor pole number NR can be any integers except the phase number and its multiples.The analysis results indicate that the optimal NR is closed to(NIS+NOS)/2 and it is odd when n is odd while it is even when n is even.Meanwhile,symmetrical phase back-EMF waveform will be obtained when the ratio of Min(NOS,NIS)to the greatest common divisor of Min(NOS,NIS)and NR is even.Based on the optimal rotor pole numbers for 6-pole outer stator with different n and corresponding optimal relative position together with same rated copper loss,the average torque is improved by 18.4%,25.1%and 25.7%respectively in PS-SFPMMs with n equal to 2,3 and 4 when compared with PS-SFPMM with n equal to 1.The analyses are validated by experiment results of the prototype machine.

Direct Torque Control System and Sensorless Technique of Permanent Magnet Synchronous Motor

The direct torque control theory has achieved great success in the control ofinduction motors. However, in the DTC drive system of Permanent Magnet Synchronous Machine (PMSM)proposed a few years ago, there are many basic theoretical problems that must be clarified. Thispaper describes an investigation about the effect of the zero voltage space vectors in the DTCsystem of PMSM and points out that if using the zero voltage space vectors rationally, not only canthe DTC system be driven successfully but also the torque ripple is reduced and the performance ofthe system is improved. This paper also studies the sensorless technique in the DTC system of PMSMand configures the DTC system of PMSM with sensorless technique including zero voltage spacevectors. Numerical simulations and experimental tests have proved the theory correct. In thecondition of sensor-less, the DTC system of PMSM is wide-rangely speed adjusting, and the ratio ofspeed adjustment is 1: 100.

Finite-Control-Set Model Predictive Control of Permanent Magnet Synchronous Motor Drive Systems——An Overview

Permanent magnet synchronous motors(PMSMs)have been widely employed in the industry. Finite-control-set model predictive control(FCS-MPC), as an advanced control scheme, has been developed and applied to improve the performance and efficiency of the holistic PMSM drive systems. Based on the three elements of model predictive control, this paper provides an overview of the superiority of the FCS-MPC control scheme and its shortcomings in current applications. The problems of parameter mismatch, computational burden, and unfixed switching frequency are summarized. Moreover, other performance improvement schemes, such as the multi-vector application strategy, delay compensation scheme, and weight factor adjustment, are reviewed. Finally, future trends in this field is discussed, and several promising research topics are highlighted.

Cogging Torque Reduction in Axial Flux PMSM with Different Permanent Magnet Combination

With the increasing requirement for the mechanical vibration and acoustic noise of the permanent magnet synchronous motor(PMSM)drive system,the demand for cogging torque reduction of PMSM has been considerably increased.To solve the problem of oversized cogging torque of axial flux PMSM,a rotor topology with hybrid permanent magnet is proposed to weaken the cogging torque.Firstly,the expression of the cogging torque of the axial flux motor is derived,and the influence of the pole-arc ratio of the permanent magnet on the cogging torque is analyzed.Secondly,the rotor structure with hybrid permanent magnet is adopted to reduce the cogging torque.According to the analytical analysis,the constraints of the size and pole-arc ratio between the hybrid permanent magnets are obtained,and the two permanent magnets related to the minimum cogging torque are determined.And the analysis results are verified by the finite element simulation.Furthermore,the motor performance with and without the hybrid permanent magnet is compared with each other.Finally,the cogging torque is significantly reduced by adopting a rotor structure with hybrid permanent magnets.

Visualization and Quantitative Evaluation of Eddy Current Loss in Bar-Wound Type Permanent Magnet Synchronous Motor for Mild-Hybrid Vehicles

This paper describes the conductor eddy current loss that occurs in a permanent magnet type synchronous motor with a distributed winding stator using a rectangular copper wire designed for mild hybrid system applications for small vehicles.Compared with the conventional round wire inserter method,the space factor can be improved and the coil-end length can be shortened by applying a so-called hairpin windings using a pre-formed into hairpin shape of bar conductor,and as a result,DC current resistance of the armature winding can be reduced.However,since the conductor cross-sectional area tends to increases,the conductor eddy current loss generated by the space harmonics linkage becomes too large to ignore.In order to study the reduction of the conductor eddy current loss,it is important to visualize the spatial leakage flux distribution which causes loss and finely analyze how the magnetic path is formed.Therefore,analysis of the conductor eddy current loss distribution generated in the bar-wound conductor is performed using the CAE model that faithfully reproduces the coil-end shape of the actual machine.Furthermore,it was qualitatively clarified what ratio of conductor eddy current loss at various driving points.Finally,the results of preliminary study on reduction of conductor eddy current loss are reported.

Electromagnetic Performance Analysis of Flux-Switching Permanent Magnet Tubular Machine with Hybrid Cores

The performance of traditional flux switching permanent magnet tubular machine(FSPMTM)are improved by using new material and structure in this paper.The existing silicon steel sheet making for all mover cores or part of stator cores are replaced by soft magnetic composite(SMC)cores,and the lamination direction of the silicon steel sheet in stator cores have be changed.The eddy current loss of the machine with hybrid cores will be reduced greatly as the magnetic flux will not pass through the silicon steel sheet vertically.In order to reduce the influence of end effect,the unequal stator width design method is proposed.With the new design,the symmetry of the permanent magnet flux linkage has been improved greatly and the cogging force caused by the end effect has been reduced.Both 2-D and 3-D finite element methods(FEM)are applied for the quantitative analysis.

Investigation and Regulation of High-efficiency Region Boundary of Variable Magnetic Flux Permanent Magnet Motor

With the increasing complexity of electrical vehicles(EVs),the wide-speed-range high-efficiency characteristics of EV drive motors are in strict demand.In this study,the variable magnetic flux effect is introduced into a permanent magnet(PM)motor,and a variable magnetic flux permanent magnetic(VMF-PM)motor is proposed.First,the flux is adjusted flexibly to synchronously broaden the speed regulation range and high-efficiency region.Subsequently,an efficiency analytical model is developed considering the motor speed,current,and flux variations.It is indicated that by the purposeful design of the variable flux leakage topology,the efficiency under high speed can be improved based on a theoretical investigation of the high-efficiency boundary.In addition,based on finite element analysis,the performances before and after optimization of the key parameters of the VMF-PM motor are investigated,including the flux variable characteristics and efficiency characteristics.Finally,a prototype motor is built and tested.Both theoretical analysis and experimental results confirm that based on the assistance of the variable magnetic flux effect,the motor high-efficiency region is broadened effectively,providing a potential research path for designing a wide-speed-range high-efficiency motor.

Airgap-harmonic-oriented Partitioned Design Method of PMV Motor with Improved Torque Performances

Here,we introduce a partitioned design method that is oriented toward airgap harmonic for permanent magnet vernier(PMV)motors.The method proposes the utilization of airgap flux harmonics as an effective bridge between the torque design region and the torque performances.To illustrate the efficacy of this method,a partitioned design PMV motor is presented and compared with the initial design.Firstly,the torque design region of the rotor is artfully divided into the torque enhancement region and ripple reduction region.Meanwhile,the main harmonics that generate output torque are chosen and enhanced,optimization.Moreover,the harmonics that generate torque ripple are selected and reduced based on torque harmonics optimization.Finally,the functions of the partitioned PMV motor torque are assessed based on the finite element method.By the purposeful design of these two regions,the output torque is strengthened while torque ripple is inhibited effectively,verifying the effectiveness and reasonability of the proposed design method.

Analysis of Torque Ripple of Permanent Magnet Brushless DC Motor

Torque tripple has significant effect on performance of permanent magnet brushless DC motor. This paper presents a mathematical model built for such a motor, the analysis of torque tripple for a brushless DC motor with sinusoidal flux distribution, which is verified by torque tripple experiments run with a test motor, and equations developed for torque tripple resulting from different sator current errors.

Developing a 3D-FEM Model for Electromagnetic Analysis of an Axial Flux Permanent Magnet Machine

Recently, many optimal designs for axial flux permanent magnet (AFPM) motors were performed based on finite- element (FE) analysis. Most of the models are based on reduction of 3D problem to 2D problem which is not accurate for design aspects. This paper describes an accurate electromagnetic analysis of a surface mounted, 28 pole AFPM with concentrated stator winding. The AFPM is modeled with three-dimensional finite-element method. This model in-cludes all geometrical and physical characteristics of the machine components. Using this accurate modeling makes it possible to obtain demanded signals for a very high precision analysis. Magnetic flux density, back-EMF, magnetic axial force and cogging torque of the motor are simulated using FLUX-3D V10.3.2. Meanwhile, the model is paramet-ric and can be used for design process and sensitivity analysis.

Reduction of Cogging Torque in Permanent Magnet Flux-Switching Machines

Permanent magnet flux-switching machine (PMFSM) is a relatively new structure. Available literatures mainly focused on its general design procedure and performance analysis. In this paper, Finite Element Method (FEM) is taken to ana-lyze various design techniques to reduce the cogging torque in a prototype 12/10-pole PMFSM.

Six-step Voltage Control of PM Brushless AC Motors under High Speed Flux-weakening Operation for EV/HEV Applications

The torque-speed characteristics of brushless motor having an interior permanent magnet rotor and a sinusoidal back-emf waveform are compared experimentally when it is operated in brushless AC(BLAC) mode and brushless DC (BLDC) modes with both 2-phase,120° conduction(BLDC-120) and 3-phase,180° conduction(BLDC-180).Particular emphasis is on high-speed,six-step voltage controlled,flux-weakening operation.It is shown that for EV/HEV applications,even for interior PM brushless motors which have sinusoidal back-emf waveforms,in order to achieve maximum torque per ampere capability over wide operation speed range,it is advantageous to employ a hybrid operation mode-BLAC operation in the constant torque region and six-step voltage control(BLDC-180 operation,together with current phase control) in the flux-weakening region.

Development of High Torque and High Power Density Hybrid Excitation Flux Switching Motor for Traction Drive in Hybrid Electric Vehicles

This paper presents design feasibility study and development of a new hybrid excitation flux switching motor (HEFSM) as a contender for traction drives in hybrid electric vehicles (HEVs). Initially, the motor general construction, the basic working principle and the design concept of the proposed HEFSM are outlined. Then, the initial drive performances of the proposed HEFSM are evaluated based on 2D-FEA, in which the design restrictions, specifications and target performances are similar with conventional interior permanent magnet synchronous motor (IPMSM) used in HEV. Since the initial results fail to achieve the target performances, deterministic design optimization approach is used to treat several design parameters. After several cycles of optimization, the proposed motor makes it possible to obtain the target torque and power of 333 Nm and 123 kW, respectively. In addition, due to definite advantage of robust rotor structure of HEFSM, rotor mechanical stress prediction at maximum speed of 12,400 r/min is much lower than the mechanical stress in conventional IPMSM. Finally, the maximum torque and power density of the final design HEFSM are approximately 11.41 Nm/kg and 5.55 kW/kg, respectively, which is 19.98% and 58.12% more than the torque and power density in existing IPMSM for Lexus RX400h.

Design of Axial-Flux Motor for Traction Application

This paper deals with the design of high power – low dimensions axial-flux permanent-magnet motor intended for trac-tion application. First, two motor configurations are analytically designed and compared using finite element calcula-tion. Then, the configuration yielding the best performances is integrated and modelled with the whole traction chain under MATLAB/SIMULINK environment in order to demonstrate the motor operation on a large speed band.