ENGINEERING CHARACTERISTICS AND ITS MECHANISM EXPLANATION OF VIBRATORY SYNCHRONIZATION TRANSMISSION

Vibratory synchronization transmission (VST) is a kind of special physicalphenomenon in inertia vibration mechanical systems. For an inertia vibration mechanical systemdriven by one pair of motors runs in step, even the power supply of one motor is cut off, the motorcan continue to keep rotating state under the vibration exciting of the machine body driven by onlyone other motor. And its rotating frequency will be the same as that of the other one. The transientprocess of this wonderful physical phenomenon has not been described quantitatively according tocurrent-existing mechanical models. On the basis of investigation of the engineering characteristicsof VST, a mechanical and electrical coupling mathematical model of a two-shaft inertia vibrationmachine is established. With this model, the transient process of VST is recurred quantitatively andsuccessfully, and a reasonable explanation is given.

Mode Selection for CoMP Transmission with Nonideal Synchronization

This paper proposes a mode selection scheme to improve the spectral efficiency for coordinated multi-point(CoMP) transmission with phase synchronization errors(PSE). Upper bounds of average achievable rate for different CoMP transmission modes, such as coordinated beamforming(CB) and joint processing(JP), are derived by random matrix theory and asymptotic mathematical approximation. According to these upper bounds, the proposed scheme switches CoMP transmission mode between CB and JP adaptively to enhance the average achievable rate. Simulation results show that these upper bounds agree well with the average achievable rates for both JP and CB, and the proposed scheme outperforms traditional single mode CoMP transmission when PSE exist.

Defect Analysis and Innovation Design of Synchronizer for Clutchless Automatic Mechanical Transmission

The synchronizer is a key component of automatic mechanical transmission(AMT)equipped in electric vehicles,but the inertial lock-ring synchronizer(ILRS)commonly used there is not suitable especially for pure electric vehicles without a clutch because of big shift impact.To make the shifting process rapid and smooth,a new synchronizer named pressure-controllable friction ring synchronizer(PCFRS)was designed.Initially,the inevitable shortcoming of ILRS was verified by simulation and test.Furthermore,the mechanical characteristics and advantages of the new synchronizer over ILRS were analyzed.Then,the formulations describing the dynamic transmission based on the working mechanism of the PCFRS were established.Finally,the shifting simulation results with PCFRS and ILRS based on the same operating conditions were compared and analyzed.The research shows that the PCFRS can meet the main shifting evaluation index of an AMT without complex control methods,as well as it takes only 0.2406 s to finish the comfortable and zero-speed-difference shifting.The shifting quality of PCFRS is better than that of the ILRS.It lays a foundation for using the new synchronizer as a part of clutchless AMTs equipped in pure electric vehicles.

CHARACTERISTICS OF ELECTROMECHANICAL COUPLING SELF-SYNCHRONIZATION OF A MULTI-MOTOR VIBRATION TRANSMISSION SYSTEM

Multi-motor vibratory transmission systems have been wide used in large vibratory machines, and four-motor linear vibratory machine is one typical equipment of them. Under non-forcible synchronization condition zero-phase synchronization of the machine is non-stationary and it-phase synchronization is stable. Under half-forcible synchronization condition in which only one motor is controlled being synchronous to another, only lag synchronization near zero-phase synchronization can be realized. Both of the characteristics have never been revealed with classical theory quantitatively. The problem is solved by means of establishing an electromechanical coupling mathematical model of the system and numerical analysis of the starting processes.

Effects of information transmission delay and channel blocking on synchronization in scale-free Hodgkin-Huxley neuronal networks

In this paper,we investigate the evolution of spatiotemporal patterns and synchronization transitions in dependence on the information transmission delay and ion channel blocking in scale-free neuronal networks.As the underlying model of neuronal dynamics,we use the Hodgkin-Huxley equations incorporating channel blocking and intrinsic noise.It is shown that delays play a significant yet subtle role in shaping the dynamics of neuronal networks.In particular,regions of irregular and regular propagating excitatory fronts related to the synchronization transitions appear intermittently as the delay increases.Moreover,the fraction of working sodium and potassium ion channels can also have a significant impact on the spatiotemporal dynamics of neuronal networks.As the fraction of blocked sodium channels increases,the frequency of excitatory events decreases,which in turn manifests as an increase in the neuronal synchrony that,however,is dysfunctional due to the virtual absence of large-amplitude excitations.Expectedly,we also show that larger coupling strengths improve synchronization irrespective of the information transmission delay and channel blocking.The presented results are also robust against the variation of the network size,thus providing insights that could facilitate understanding of the joint impact of ion channel blocking and information transmission delay on the spatiotemporal dynamics of neuronal networks.

Novel Adaptive Neural Controller Design Based on HVDC Transmission System to Damp Low Frequency Oscillations and Sub Synchronous Resonance

This paper presents the effect of the high voltage direct current (HVDC) transmission system based on voltage source converter (VSC) on the sub synchronous resonance (SSR) and low frequency oscillations (LFO) in power system. Also, a novel adaptive neural controller based on neural identifier is proposed for the HVDC which is capable of damping out LFO and sub synchronous oscillations (SSO). For comparison purposes, results of system based damping neural controller are compared with a lead-lag controller based on quantum particle swarm optimization (QPSO). It is shown that implementing adaptive damping controller not only improves the stability of power system but also can overcome drawbacks of conventional compensators with fixed parameters. In order to determine the most effective input of HVDC system to apply supplementary controller signal, analysis based on singular value decomposition is performed. To evaluate the performance of the proposed controller, transient simulations of detailed nonlinear system are considered.

Research and Test of Three-Pulley Noncircular Synchronous Pulley Transmission Mechanism with Minimum Slack

The noncircular synchronous belt drive mechanism has demonstrated certain achievements and has been used in special fields.Research regarding noncircular synchronous belt drive mechanisms has focused on optimization design and kinematic analysis in China,whereas two pulley noncircular synchronous belt transmissions have been developed overseas.However,owing to the noncircular characteristics of the belt pulley,the real-time variation in the belt length slack during the transmission of the noncircular synchronous belt is significant,resulting in high probabilities of skipping and vibration.In this study,a noncircular tensioning pulley is added to create a stable three-pulley noncircular synchronous belt driving mechanism and a good synchronous belt tensioning,with no skipping;hence,the non-uniform output characteristic of the driven pulley is consistent with the theoretical value.In the circular noncircular noncircular three-pulley noncircular synchronous belt mechanism,the pitch curve of the driving synchronous belt pulley is circular,whereas those of the driven synchronous belt and tensioning pulleys are noncircular.To minimize the slack of the belt length of the synchronous belt and the constraint of the concavity and circumference of the tensioning pulley,an automatic optimization model of the tensioning pulley pitch curve is established.The motion simulation,analysis,and optimization code for a three-belt-pulley noncircular synchronous belt drive mechanism is written,and the variation in belt length slack under different speed ratios is analyzed based on several examples.The testbed for a circular-noncircular-noncircular three-pulley noncircular synchronous belt transmission mechanism is developed.The test shows that the three-pulley noncircular synchronous belt drives well.This study proposes an automatic optimization algorithm for the tensioning pulley pitch curve of a noncircular synchronous belt transmission mechanism;it yields a stable transmission of the noncircular synchronous belt transmission mechanism as well as non-uniform output characteristics.

Monolithical Integrated CMOS Injected Synchronized Ring

Oscillator IC technique is developed by combining injecting synchronization technique with a ring VCO.Using the technique,a novel 2 488GHz of monolithical integrated injected synchronized ring VCO (ISRVCO) is realized in a standard 0 25μm CMOS process.The ISRVCO is characterized by the following performances: -100dBc /Hz@1MHz at free running frequency,-91 7dBc/Hz@10kHz when injection is locked.With the 3 3V of power supply,the tuning range is 150MHz and the locking range is 100MHz with 50m V p p signal injection.

Taming desynchronized bursting with delays in the Macaque cortical network

Inhibitory coupled bursting Hindmarsh-Rose neurons are considered as constitutive units of the Macaque corti- cal network. In the absence of information transmission delay the bursting activity is desynchronized, giving rise to spatiotemporally disordered dynamics. This paper shows that the introduction of finite delays can lead to the synchro- nization of bursting and thus to the emergence of coherent propagating fronts of excitation in the space-time domain. Moreover, it shows that the type of synchronous bursting is uniquely determined by the delay length, with the transi- tions from one type to the other occurring in a step-like manner depending on the delay. Interestingly, as the delay is tuned close to the transition points, the synchronization deteriorates, which implies the coexistence of different bursting attractors. These phenomena can be observed by different but fixed coupling strengths, thus indicating a new role for information transmission delays in realistic neuronal networks.

Design and Realization of Phased Array Radar Optical Fiber Transmission System

One optical fiber transmission system is designed. The modularization optical fiber transmission adapters were utilized in the system, so the system structure could be flexibly sealable. The sub-array adapter and signal processor adapter were designed and realized utilizing the new field programmable gate array （FP- GA） which could drive the optical transceiver. The transmission agreement was designed based on the data stream. In order to solve the signal synchronization problem of the optical fiber transmitted phased array radar, a method named synchronous clock was designed. The fiber transmission error code rate of the system was zero with an experimental transmission velocity of 800 Mbit/s. The phased array radar system has detected the airplane target, thus validated the feasibility of the design method.

Fault Location Method for STATCOM Connected Transmission Lines Using CCM

Determining the fault location using conventional impedance based distance relay in the presence of FACTS controllers is a challenging task in a transmission line. A new distance protection method is developed to locate the fault in a transmission line compensated with STATCOM with simple calculations. The proposed protection method considers the STATCOM injected/absorbed current to correct the fault loop apparent impedance and accordingly calculates the actual distance to the fault location. The comprehensive equations needed for apparent impedance calculation are also outlined and the performance is evaluated and tested with a typical 400 KV transmission system for different fault types and locations using MATLAB/SIMULINK software. The evaluation results indicate that the new protection method effectively estimates the exact fault location by mitigating the impact of STATCOM on distance relay performance with error less than 0.3%.

Design of Wireless Transmission System for Shallow Seismograph Based on 433 M Module

Because of its portability,the non-cable seismograph has become the future development trend of geophysical instruments.A new wireless data transmission device of 433 M module was proposed;a wireless network was built using the EL1663B_PA module of the SI4463 core,and through the SPI interface to modify the internal parameters.Data transmission used dual antenna mode,the main station as the center of the wireless network coverage up to 550 m or more.The wireless time synchronization system was designed to realize the wireless connection communication between the shallow seismograph and the sensor of each observation point.This program aimed to eliminate the necessary connecting cable and batteries between the conventional shallow seismograph and the detector,greatly reducing the weight of the equipment,and making the shallow seismograph truly low cost,lightweight,flexible and easy to operate and so on.

Synchronization of two coupled exciters in a vibrating system of spatial motion

The paper proposes an analytical approach to investigate the synchronization of the two coupled exciters in a vibrating system of spatial motion. Introducing the distur- bance parameters for average angular velocity of two excit- ers, we deduce the non-dimensional coupling equations of angular velocities of two exciters, in which the inertia cou- pling matrix is symmetric and the stiffness coupling matrix is antisymmetric in a non-resonant vibrating system. The analysis of the coupling dynamic characteristic shows that the coupled cosine effect of the phase angles will cause the torque acting on two motors to limit the increase of phase difference between two exciters as well as sustain its sym- metry of two exciters during the running process. It physi- cally explains the peculiarity of self-synchronization of two exciters. The cosine effect of phase angles of the vibrations excited by each exciter will decrease its moment of inertia. The residual moment of inertia of each exciter represents its relative moment of inertia. The stability condition of synchro- nization of two exciters is that the relative non-dimensional moments of inertia of two exciters are all greater than zero and four times their product is greater than the square of their coefficient of coupled cosine effect of phase angles, which is equivalent to that the inertia coupling matrix is positive definite and all its elements are positive. The numeric results show that the structure of the vibrating system can ensure the stability condition of synchronous operation.

Synchronization of three homodromy coupled exciters in a non-resonant vibrating system of plane motion

In this paper, the synchronization problem of three homodromy coupled exciters in a non-resonant vibrating system of plane motion is studied. By introducing the average method of modified small parameters, we deduced dimensionless coupling equation of three exciters, which converted the problem of synchronization into that of the existence and stability of zero solutions for the average differential equations of the small parameters. Based on the dimensionless coupling torques and characteristics of the cor- responding limited functions, the synchronization criterion for three exciters was derived as the absolute value of dimensionless residual torque difference between arbitrary two motors being less than the maximum of their dimensionless coupling torques. The stability criterion of its synchronous state lies in the double-condition that the inertia coupling matrix is positive definite and all its elements are positive as well. The synchronization determinants are the coefficients of synchronization ability, also called as the general dynamical symmetry coefficients. The double-equilibrium state of the vibrating system is manifested by numeric method, and the numeric and simulation results derived thereof indicate the indispensable and crucial role the structural parameters of the vibrating system play in the stability criterion of synchronous operation. Besides, by adjusting its structural parameters, the elliptical motion of the vibrating system successfully met the requirements in engineering applications.

Designing of New Data Synchronization System

As the rapid development of Wireless Communications and the popularity of the Intelligent Terminal, data synchronization has been a social focus, meanwhile, user terminal devices are increasingly diversified, traditional synchronization technology based C/S mode has such deficiencies as insufficient amount of transmitting data and bad Real-time efficiency. It has become increasingly unable to meet the needs of future development. In this paper, we proposed and designed a new method and system by separating control with transmission to synchronize data to ensure Real-time data and improve efficiency.

A consensus time synchronization protocol in wireless sensor network

Time synchronization is one of the base techniques in wireless sensor networks(WSNs).This paper proposes a novel time synchronization protocol which is a robust consensusbased algorithm in the existence of transmission delay and packet loss.It compensates for transmission delay and packet loss firstly,and then,estimates clock skew and clock offset in two steps.Simulation and experiment results show that the proposed protocol can keep synchronization error below 2μs in the grid network of 10 nodes or the random network of 90 nodes.Moreover,the synchronization accuracy in the proposed protocol can keep constant when the WSN works up to a month.

Non-PLL high-precision synchronous sampling method among lots of acoustics acquisition channels for underwater multilinear array seismic exploration system

Synchronous sampling is very essential in underwater multilinear array seismic exploration system in which every acquisition node(AN)samples analog signals by its own analog-digital converter(ADC).Aiming at the problems of complex synchronous sampling method and long locking time after varying sampling rate in traditional underwater seismic exploration system,an improved synchronous sampling model based on the master-slave synchronous model and local clock asynchronous drive with non phase locked loop(PLL)is built,and a high-precision synchronous sampling method is proposed,which combines the short-term stability of local asynchronous driving clock with the master-slave synchronous calibration of local sampling clock.Based on the improved synchronous sampling model,the influence of clock stability,transmission delay and phase jitter on synchronous sampling error is analyzed,and a high-precision calibration method of synchronous sampling error based on step-by-step compensation of transmission delay is proposed.The model and method effectively realize the immunity of phase jitter on synchronous sampling error in principle,and compensate the influence of signal transmission delay on synchronous sampling error.At the same time,it greatly reduces the complexity of software and hardware implementation of synchronous sampling,and solves the problem of long locking time after changing the sampling rate in traditional methods.The experimental system of synchronous sampling for dual linear array is built,and the synchronous sampling accuracy is better than 5 ns.

双三相同步磁阻电机单相开路故障下的容错控制策略

双三相同步磁阻电机(dual three-phase synchronous reluctance motor,DTP-SynRM)转子不含永磁体,没有高温退磁风险,成本较低,且由于其系统自由度高、冗余性强,因此具有较好的容错性能。开路故障是双三相同步磁阻电机系统中最常见的故障类型之一,该文针对一种两套三相绕组中性点相互独立的双三相同步磁阻电机单相开路故障,建立DTP-SynRM矢量空间解耦模型,实现对电压、电流和磁链方程的完全解耦。在开路故障状态下仍将其视为一个正常的双三相电机,分析故障状态对电机的电流约束和信号传递的影响,并指出在开路故障下z2轴电流与β轴电流不再独立,电机由正常运行时的四阶系统降阶为三阶系统,而由于开路故障导致的电压信号传递不准确则会在dq坐标系中引入二次谐波电流,并产生二次和四次转矩波动。该文提出一种同时考虑电流约束和信号传递误差的故障容错方法,电机处于三闭环运行状态,补偿电压信号传递误差,抑制开路故障时电机的转矩波动并降低电流谐波。搭建实验平台进行实验,验证所提容错方法的有效性和可行性。

励磁绕组与阻尼绕组耦合效应对大型同步调相机转子暂态电流特性的影响

针对大型同步调相机暂态分析时模型精度较低的问题,提出一种考虑励磁绕组与阻尼绕组耦合效应的同步调相机暂态分析精确模型。首先,通过引入特征电抗建立同步调相机考虑励磁绕组与阻尼绕组耦合效应的暂态分析精确模型,并基于励磁电流拟合对特征电抗进行求解。然后,通过三相短路与BC相间短路故障仿真,对比同步调相机传统模型与精确模型的转子暂态电流特性。最后,建立同步调相机机-网暂态仿真模型,分析系统送端交流母线电压波动时同步调相机精确模型的暂态运行特性。研究表明,考虑励磁绕组与阻尼绕组耦合效应时同步调相机转子暂态电流特性的精度更高。三相短路与BC相间短路故障后3个周期内,同步调相机暂态分析精确模型励磁电流峰值平均值的精度分别提高了27.27%和61.53%。

数字示波器中FPGA间高速信号传输同步方法

数据采集系统是数字示波器(DSO)的核心组成单元,随着示波器带宽采样率的逐步提升,单片模数转换器(ADC)+现场可编辑门控阵列(FPGA)的架构难以满足超高速以及多通道的应用场景,因此,高端示波器中数据采集系统普遍采用“主从”FPGA控制架构。在该架构下,多个FPGA之间信号的同步传输是实现采集系统的同步和精确采集的重要前提。针对多FPGA板卡之间的信号同步传输问题,提出了一种FPGA之间高速信号同步传输的方法,借助FPGA的IODELAY单元,通过测试数据训练找到最稳定的同步传输区间,实现多FPGA之间的同步传输。在自研的数字示波器上的实验表明,该方法能够有效实现FPGA之间高速信号的同步传输。