A HPLC Method for the Determination of Salmon Calcitonin in Injection by Gradient Elution

It was concluded that the described HPLC method could be used for the assayof salmon calcitonin in injection, as it offers qualified selectivity, accuracy and precision ofanalysis.

Establishing a rat model of spastic cerebral palsy by targeted ethanol injection

Spastic cerebral palsy is generally considered to result from cerebral cortical or pyramidal tract damage. Here, we precisely targeted the left pyramidal tract of 2-month-old Sprague-Dawley rats placed on a stereotaxic instrument under intraperitoneal anesthesia. Based on the rat brain stereotaxic map, a 1-mm hole was made 10 mm posterior to bregma and 0.8 mm left of sagittal suture. A microsyringe was inserted perpendicularly to the surface of the brain to a depth of 9.7 mm, and 15 wL of ethanol was slowly injected to establish a rat model of spastic cerebral palsy. After modeling, the rats appeared to have necrotic voids in the pyramidal tract and exhibited typical signs and symptoms of flexion spasms that lasted for a long period of time. These findings indicate that this is an effective and easy method of establishing a rat model of spastic cerebral palsy with good reproducibility. Ethanol as a chemical ablation agent specifically and thoroughly damages the py- ramidal tract, and therefore, the animals display flexion spasms, which are a typical symptom of the disease.

Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method

A non-isothermal injection molding process for a non-Newtonian viscous pseudoplastic fluid is simulated.A conservative interface capturing technique and the flow field solving method are coupled to perform a dynamic simulation.The validity of the numerical method is verified by a benchmark problem.The melt interface evolution versus time is captured and the physical quantities such as temperature,velocity and pressure at each time step are obtained with corresponding analysis.A"frozen skin"layer with the thickness increasing versus time during the injection process is found.The fact that the"frozen skin"layer can be reduced by increasing the injection velocity is numerically verified.The fountain flow phenomenon near the melt interface is also captured.Moreover,comparisons with the non-isothermal Newtonian case show that the curvatures of the interface arcs and the pressure contours near the horizontal mid-line of the cavity for the non-Newtonian pseudoplastic case is larger than that for the Newtonian case.The velocity profiles are different at different positions for the non-Newtonian pseudoplastic case,while in the case of Newtonian flow the velocity profiles are parabolic and almost the same at different positions.

A fast explicit finite difference method for determination of wellhead injection pressure

A fast explicit finite difference method (FEFDM),derived from the differential equations of one-dimensional steady pipe flow,was presented for calculation of wellhead injection pressure.Recalculation with a traditional numerical method of the same equations corroborates well the reliability and rate of FEFDM.Moreover,a flow rate estimate method was developed for the project whose injection rate has not been clearly determined.A wellhead pressure regime determined by this method was successfully applied to the trial injection operations in Shihezi formation of Shenhua CCS Project,which is a good practice verification of FEFDM.At last,this method was used to evaluate the effect of friction and acceleration terms on the flow equation on the wellhead pressure.The result shows that for deep wellbore,the friction term can be omitted when flow rate is low and in a wide range of velocity the acceleration term can always be deleted.It is also shown that with flow rate increasing,the friction term can no longer be neglected.

New approach to develop a 3D non-isothermal computational framework for injection molding process based on level set method

The simulation of three-dimensional （3D） non-isothermal, non-Newtonian fluid filling process is an extremely difficult task and remains a challenging problem, which includes polymer melt flow with free surface coupled with transient heat transfer. This paper presents a full 3D non-isothermal two-phase flow model to predict the complex flow in melt filling process, where the Cross-WLF model is applied to characterize the rheological behav- ior of polymer melt. The governing equations are solved using finite volume method with SIMPLEC algorithm on collocated grids and the melt front is accurately captured by a high resolution level set method. A domain exten- sion technique is adopted to deal with the complex cavities, which greatly reduces the computational burden. To verify the validity of the developed 3D approach, the melts filling processes in two thin rectangular cavities （one of them with a cylindrical insert） are simulated. The predicted melt front interfaces are in good agreement with the experiment and commercial software prediction. For a case with a rather complex cavity, the dynamic filling process in a hemispherical shell is successfully simulated. All of the numerical results show that the developed numerical procedure can provide a reasonable orediction for injection molding process.

Oil oxidation in the whole temperature regions during oil reservoir air injection and development methods

The oil oxidation characteristics of the whole temperature regions from 30 ℃ to 600 ℃ during oil reservoir air injection were revealed by experiments. The whole oil oxidation temperature regions were divided into four different parts: dissolving and inflation region, low temperature oxidation region, medium temperature oxidation region and high temperature oxidation region. The reaction mechanisms of different regions were explained. Based on the oil oxidation characteristics and filed tests results, light oil reservoirs air injection development methods were divided into two types: oxygen-reducing air flooding and air flooding;heavy oil reservoirs air injection in-situ combustion development methods were divided into two types: medium temperature in-situ combustion and high temperature in-situ combustion. When the reservoir temperature is lower than 120 ℃, oxygen-reducing air flooding should be used for light oil reservoir development. When the reservoir temperature is higher than 120 ℃, air flooding method should be used for light oil reservoir development. For a normal heavy oil reservoir, when the combustion front temperature is lower than 400 ℃, the development method is medium temperature in-situ combustion. For a heavy oil reservoir with high oil resin and asphalting contents, when the combustion front temperature is higher than 450 ℃, the development method at this condition is high temperature in-situ combustion. Ten years field tests of air injection carried out by PetroChina proved that air has advantages in technical, economical and gas source aspects compared with other gas agents for oilfield gas injection development. Air injection development can be used in low/super-low permeability light oil reservoirs, medium and high permeability light oil reservoirs and heavy oil reservoirs. Air is a very promising gas flooding agent.

Safety Study of Flunixin Meglumine Injection on Target Animal Dogs

The study was conducted to evaluate the safety of Flunixin meglumine injection on target animal dogs, and to provide a scientific basis for the dose selec- tion of clinical application. A total of 24 healthy Springer Spaniels were randomly divided into four groups. Intramuscular injection of Flunixin meglumine was carried out to test group dogs with the doses of 2 rag/kg, 6 rag/kg, 10 mg/kg for 5 days, respectively. The injected doses were one times, three times and five times as the recommended clinical dose. Intramuscular injection of water was carried out to control group dogs for 5 days. Clinical symptom was observed after the injection, and the blood was collected at different times （before, during and after the injection） to conduct blood routine examination and blood biochemical indexes measurement. Post-mortem examination and histopathological examination were carried out after the test. The results indicated that test dogs showed normal spirit, with no death and no other adverse reactions. Part values of blood routine examination indexes and blood biochemical indexes in test groups showed significant differences between pre-administration and post-administration, but basically fluctuated within the reference range. Autopsy results showed no obvious pathological changes. Histological examination showed the viscera and tissues （liver, heart, spleen, lung, kidney） in high dose group and control group showed no abnormality and pathological changes. The results indicated that Flunixin meglumine injection with the dose of 2 - 10 rag/kg had a minimal effect on physiological and biochemical indexes of dog blood.

Power System State Estimation Solution With Zero Injection Constraints Using Modified Newton Method and Fast Decoupled Method in Polar Coordinate

如何保证零注入节点的注入功率在状态估计结果中严格为0是电力系统状态估计研究中的重要问题。在直角坐标下,由于零注入约束为线性约束,可使用修正牛顿法来有效地解决这一问题。因此,借鉴直角坐标下修正牛顿法的思路,提出了极坐标下的修正牛顿法和修正快速解耦估计。这些方法的计算流程与传统的极坐标下的牛顿法和快速解耦估计非常相似,计算速度与大权重法相当,同时能够保证零注入约束严格满足。仿真结果验证了所得结论。

Optimization of siRNA Delivery Method into the Liver by Sequential Injection of Polyglutamic Acid and Cationic Lipoplex

Previously, we developed a novel siRNA transfer method to the liver by sequential intravenous injection of poly-L-glutamic acid (PGA) and cationic liposome/siRNA complex (cationic lipoplex). In this study, we examined the effects of the charge ratio (+/-) of cationic liposome/siRNA, molecular weight of PGA and cationic lipid of cationic liposome on the biodistribution of siRNA after sequential injection of PGA plus cationic lipoplex. When 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP)/cholesterol (Chol) lipoplex was intravenously injected into mice, the accumulation of siRNA was mainly observed in the lungs. In contrast, when DOTAP/Chol lipoplex was intravenously injected at 1 min after intravenous injection of PGA, siRNA was largely accumulated in the liver. The charge ratio (+/-) of DOTAP/Chol liposome/siRNA did not affect the biodistribution of siRNA after sequential injection. As regards the molecular weight of PGA, the accumulation of siRNA was observed mainly in the liver after the sequential injection of PGA of 20.5, 38, 64 or 200 kDa plus DOTAP/Chol lipoplex. Furthermore, to examine the effect of cationic lipid of cationic liposome on the biodistribution of siRNA, we prepared other cationic liposomes composed of 1,2-di-O-octadecenyl-3-trimethylammonium propane chloride (DOTMA)/Chol, dimethyldioctade-cylammonium bromide (DDAB)/Chol and O,O’-ditetradecanoyl-N-(α-trimethylammonioacetyl)di-ethanolamine chloride (DC-6-14)/Chol. For the cationic liposomes, the accumulation of siRNA was observed mainly in the liver when their cationic lipoplexes were sequentially injected after injection of PGA into mice. From these findings, sequential injection of PGA plus cationic lipoplex could deliver siRNA efficiently into the liver regardless of the charge ratio (+/-) of lipoplex, lengths of PGA and cationic lipid of liposome.

Single Phase-to-Ground Fault Line Identification and Section Location Method for Non-Effectively Grounded Distribution Systems Based on Signal Injection

A diagnostic signal current trace detecting based single phase-to-ground fault line identifica- tion and section location method for non-effectively grounded distribution systems is presented in this paper.A special diagnostic signal current is injected into the fault distribution system,and then it is detected at the outlet terminals to identify the fault line and at the sectionalizing or branching point along the fault line to locate the fault section.The method has been put into application in actual distribution network and field experience shows that it can identify the fault line and locate the fault section correctly and effectively.

A New Method for the Dynamic Reserves of Gas Condensate Reservoir Using Cyclic Gas Injection Based on the Effects of Reinjection Ratio and Water Influx

As we all know, cyclic gas injection is one of the most effective development methods to improve condensate oil recovery. When dealing with the calculation of the reserves, the injection-production differences and water influx create great influence on the accuracy. Based on the existing research, we proposed a new material balance equation which considered the differences of composition between produced and injected fluids and the effect of water influx, and a solution was provided in this paper. The results of the method are closer to the actual situation because they are built on the law of conservation of mass, and the using of curve fitting method can not only avoid the use of water influx coefficient but also obtain the water influx rate and reserves at the same time. The YH-23 gas condensate reservoir is taking as a typical subject to do the research, which has been exploited by cycle gas injection for 14 years. Three different methods are used to calculate the reserves, and the results show that the method proposed in this paper has minimum error of 2.96%.

Research on subsidence method aided by water injection and its engineering application for the north anchor of Taizhou Bridge

The north anchorage caisson of Taizhou Bridge encountered some difficulties during the sinking process for the large sidewall frictional resistances. To solve this problem, a new concept and method called subsidence method aided by water injection is proposed. Numeral analysis is adopted to simulate the effects of this method for the north anchor of Taizhou Bridge, which confirmed the feasibility and validity. Finally, the method is applied to the north anchor caisson during the caisson sinking procedure and helps the caisson sink and embed to the designed position smoothly.

Research on the Equivalence Between Double Differential- mode Current Injection and Radiation Test Method

There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cable simultaneously, a double differential-mode current in- jection test method (DDMCI) is proposed. The method adopted the equivalence source wave theorem and Baum-Liu-Tesche(BLT) equation as its theory foundation. The equivalent corresponding relation between injection voltage and radiation electric field intensity is derived, and the phase relation between the two injection voltage sources is confirmed. The results indicate that the amplitude and phase of the equivalent injection voltage source is closely related to the S parameter of directional coupling device, the transmission line length, and the source vector in BLT equation, but has nothing to do with the reflection coefficient between the two equipment pieces. Therefore, by choosing the right amplitude and phase of the double injection voltage sources, the DDMCI test is equivalent to the radiation test for two interconnected equipment of a system.

Network pharmacology to predicting therapy targets of traditional Chinese medicine Kang’ai injection on breast cancer

Background:To predict the effective targets of Kang’ai injection and analyze the pharmacological mechanism for the treatment of breast cancer based on the method of network pharmacology.Methods:The Traditional Chinese Medicine Systems Pharmacology database was used to predict the effective components of the Chinese patent medicine Kang’ai injection,and GeneCards database,Online Mendelian Inheritance in Man database and the Therapeutic Target Database were used to predict the therapeutic targets of breast cancer.Cytoscape 3.7.2 was used to construct active ingredient-disease-target network.String database and Cytoscape 3.7.2 software were used to draw the protein-protein interaction network and obtain the core target.Bioconductor and R language were used to analyze the effective action target for gene ontology and Kyoto Encyclopedia of Genes and Genomes pathway enrichment analysis.Results:There were 42 effective active ingredients in the Chinese patent medicine Kang’ai injection,which acted on 105 targets,and it had 32 components that acted on 96 targets associated with breast cancer.The target regulates various biological processes such as inflammation,angiogenesis,apoptosis and cell proliferation,and regulates pathways such as PI3K-Akt signaling pathway,MAPK signaling pathway,AGE-RAGE signaling pathway in diabetic complications and thyroid hormone signaling pathway through gene ontology and Kyoto Encyclopedia of Genes and Genomes analysis.Conclusion:The treatment of breast cancer with the Chinese patent medicine Kang’ai injection is a complex mechanism process with multiple targets,multiple pathways,and multiple choices,which provides a theoretical basis for the further extraction of effective components in the treatment of breast cancer.

Clinical Observation on Brachial Plexus Block with “One Injection Two Points” Method Guiding by Ultrasound

OBJECTIVE: To compare the clinical effect of brachial plexus block with "One Injection Two Points" guided under ultrasound and the conventional method guiding by ultrasound. METHODS: 70 patients were randomized evenly into 2 groups, with 35 patients in each group, while the Experiment Group(Group B) received One Injection Two Points" method, the Control Group(Group A) received the conventional method.The nerve block every 5 s, the success rate of anesthesia, the dosage of local anesthetics, second remedial anesthesia, adverse reactions, etc.were recorded. RESULTS: Group B was superior to group A in the success rate of anesthesia; There were 6 patients in group A who required constant pump injection of Remifentanil to remedy, while no patients in Group B needed remedy treatment. There were no serious adverse reactions in both groups.CONCLUSIONS: The clinical effect of brachial plexus block with "One Injection Two Points" method guided under ultrasoundguiding by ultrasound was superior to that of the conventional method.

Fast-moving target tracking based on mean shift and frame-difference methods

The mean shift tracker has difficulty in tracking fast moving targets and suffers from tracking error accumulation problem. To overcome the limitations of the mean shift method, a new approach is proposed by integrating the mean shift algorithm and frame-difference methods. The rough position of the moving tar- get is first located by the direct frame-difference algorithm and three-frame-difference algorithm for the immobile camera scenes and mobile camera scenes, respectively. Then, the mean shift algorithm is used to achieve precise tracking of the target. Several tracking experiments show that the proposed method can effectively track first moving targets and overcome the tracking error accumulation problem.

Solution of scattering from rough surface with a 2D target above it by a hybrid method based on the reciprocity theorem and the forward-backward method

This paper proposes a hybrid method based on the forward-backward method （FBM） and the reciprocity theorem （RT） for evaluating the scattering field from dielectric rough surface with a 2D target above it. Here, the equivalent electric/magnetic current densities on the rough surface as well as the scattering field from it are numerically calculated by FBM, and the scattered field from the isolated target is obtained utilizing the method of moments （MOM）. Meanwhile, the rescattered coupling interactions between the target and the surface are evaluated employing the combination of FBM and RT. Our hybrid method is first validated by available MOM results. Then, the functional dependences of bistatic and monostatic scattering from the target above rough surface upon the target altitude, incident and scattering angles are numerically simulated and discussed. This study presents a numerical description for the scattering mechanism associated with rescattered coupling interactions between a target and an underlying randomly rough surface.

TWO-PHASE FLOW FOR A HORIZONTAL WELL PENETRATING A NATURALLY FRACTURED RESERVOIR WITH EDGE WATER INJECTION

This paper examines the two-phase flow for a horizontal well penetrating a naturally fractured reservoir with edge water injection by means of a fixed streamlinemodel,The mathematical model of the verical two-dimensional flow or oil-water for a horizontal well in a medium with double-porosity is established ,and whose accuratesolutions are obtained by using the characteristic method .The saturation distributionsin the fractured system and the matrix system as well as the formula of the time of water free production are presented .All these results provide a theoretical basis and a computing method for oil displacement by edge water from naturally fracturedreservirs.

Fault injection system for automatic testing system

Considering the deficiency of the means for confirming the attribution of fault redundancy in the re-search of Automatic Testing System(ATS) , a fault-injection system has been proposed to study fault redundancyof automatic testing system through compurison. By means of a fault-imbeded environmental simulation, thefaults injected at the input level of the software are under test. These faults may induce inherent failure mode,thus bringing about unexpected output, and the anticipated goal of the test is attained. The fault injection con-sists of voltage signal generator, current signal generator and rear drive circuit which are specially developed,and the ATS can work regularly by means of software simulation. The experimental results indicate that the faultinjection system can find the deficiency of the automatic testing software, and identify the preference of fault re-dundancy. On the other hand, some soft deficiency never exposed before can be identified by analyzing the tes-ting results.