A new radial friction welding technology of 30 mm shell's band is introduced.Bands are assembled to shell bodies without notches by using the process.The width of heat-affected zone(HAZ) is small,and the microstru...A new radial friction welding technology of 30 mm shell's band is introduced.Bands are assembled to shell bodies without notches by using the process.The width of heat-affected zone(HAZ) is small,and the microstructure on steel side is incomplete quenching while that on cooper side is grain refining.The shear-strength of joint exceeds 200 MPa.The result of firing test indicates that radial friction welding can satisfy the assembly requirements of shell bands.展开更多
Based on impulse and vibration machining theories,a mathematical model of cutting force for the electroplated diamond ultrasonic wire saw was established using superposition principle.The differences between the cutti...Based on impulse and vibration machining theories,a mathematical model of cutting force for the electroplated diamond ultrasonic wire saw was established using superposition principle.The differences between the cutting forces with and without ultrasonic effect were analyzed theoretically and experimentally.The results indicate that the cutting force of diamond wire increases along with the spindle speed decrease and the lateral pressure increase.The force in ultrasonic vibration cutting is about 20% to 30% less than that in conventional cutting.Also,the cutting trajectory of single diamond grit in sawing process is simulated,and the reason that the ultrasonic vibration can reduce the cutting force is explained further.展开更多
The generation and development of microcracks of SiCp/Al materials in the machining process were researched, and the forming causes and mechanism of the cut surface morphology for ap=0.2 mm or ap=0.4 mm and at 2 m/min...The generation and development of microcracks of SiCp/Al materials in the machining process were researched, and the forming causes and mechanism of the cut surface morphology for ap=0.2 mm or ap=0.4 mm and at 2 m/min～10 m/min were systematically analyzed. The supporting and "floor"roles of aluminum are wake at a shallower cutting depth and a lower speed, the SiC particles are shed under the role of cutting force, and the microcrack size of cut surface is larger. With the increase in the cutting depth and the cutting speed, the cutting temperature increases, the supporting and "floor" roles of aluminum are enhanced, the shedding and fracture of the reinforcement particles are flexible under the action of the cutting force, the fracture of cutting transforms from brittle to ductile, and the expansion of microcrack on the entire surface tends to balance with a smaller size. A curve between the cutting force and the cutting speed was plotted, a microcrack form of the cut surface was given, and some theoretical basis is provided for the mechanical processing and the surface quality.展开更多
The cutting process of electroplated diamond wire saw was researched on the basis of impulse and vibration machining theories. The different contact states in the cutting process were analyzed by using the finite elem...The cutting process of electroplated diamond wire saw was researched on the basis of impulse and vibration machining theories. The different contact states in the cutting process were analyzed by using the finite element method. It shows that the cutting stress is uniformly distributed along the direction of the workpiece width in the steady state. A mathematical equation of sawing trajectory was established by using the superposition principle and the cutting experiment of wire saw to calculate the cutting trajectory. The comparison of the theoretical trajectory with the calculated one indicates that the error is less than 15%. The research results provide a theoretic basis for optimization of the saw's cutting process parameters.展开更多
In order to find out the contact pressure intensity distribution and its effects on the workepiece flatness error in plane polishing with retaining ring,the contact model and the boundary conditions are built up based...In order to find out the contact pressure intensity distribution and its effects on the workepiece flatness error in plane polishing with retaining ring,the contact model and the boundary conditions are built up based on the axial symmetric elastic contact theory.The pressure intensity distribution is calculated and analyzed with the help of the Hankel transform theory and the constructing solution method of Chebyshev orthogonal polynomials.And then,the effects of the dimensionless ring-workpiece gap,the load ratio of the retaining ring and the dimensionless ring width on the contact pressure intensity distribution are obtained.Finally,based on the distribution theory of material removal volume,the effects of the pressure intensity distributions on the flatness errors of polished workpiece are also investigated experimentally.The results show that the contact pressure intensity distribution becomes more uniform and the better profile of polished workpiece can also be obtained,if the dimensionless ring-workpiece gap is reduced,the load ratio is selected as 0.6 to 0.85,and the dimensionless ring width is taken as 0.13 to 0.40.展开更多
文摘A new radial friction welding technology of 30 mm shell's band is introduced.Bands are assembled to shell bodies without notches by using the process.The width of heat-affected zone(HAZ) is small,and the microstructure on steel side is incomplete quenching while that on cooper side is grain refining.The shear-strength of joint exceeds 200 MPa.The result of firing test indicates that radial friction welding can satisfy the assembly requirements of shell bands.
基金Sponsored by Liaoning Innovation Team Fundation(2008T164)
文摘Based on impulse and vibration machining theories,a mathematical model of cutting force for the electroplated diamond ultrasonic wire saw was established using superposition principle.The differences between the cutting forces with and without ultrasonic effect were analyzed theoretically and experimentally.The results indicate that the cutting force of diamond wire increases along with the spindle speed decrease and the lateral pressure increase.The force in ultrasonic vibration cutting is about 20% to 30% less than that in conventional cutting.Also,the cutting trajectory of single diamond grit in sawing process is simulated,and the reason that the ultrasonic vibration can reduce the cutting force is explained further.
文摘The generation and development of microcracks of SiCp/Al materials in the machining process were researched, and the forming causes and mechanism of the cut surface morphology for ap=0.2 mm or ap=0.4 mm and at 2 m/min～10 m/min were systematically analyzed. The supporting and "floor"roles of aluminum are wake at a shallower cutting depth and a lower speed, the SiC particles are shed under the role of cutting force, and the microcrack size of cut surface is larger. With the increase in the cutting depth and the cutting speed, the cutting temperature increases, the supporting and "floor" roles of aluminum are enhanced, the shedding and fracture of the reinforcement particles are flexible under the action of the cutting force, the fracture of cutting transforms from brittle to ductile, and the expansion of microcrack on the entire surface tends to balance with a smaller size. A curve between the cutting force and the cutting speed was plotted, a microcrack form of the cut surface was given, and some theoretical basis is provided for the mechanical processing and the surface quality.
基金Sponsored by Innovation team item fund of Liaoning Province ( 2008T164)
文摘The cutting process of electroplated diamond wire saw was researched on the basis of impulse and vibration machining theories. The different contact states in the cutting process were analyzed by using the finite element method. It shows that the cutting stress is uniformly distributed along the direction of the workpiece width in the steady state. A mathematical equation of sawing trajectory was established by using the superposition principle and the cutting experiment of wire saw to calculate the cutting trajectory. The comparison of the theoretical trajectory with the calculated one indicates that the error is less than 15%. The research results provide a theoretic basis for optimization of the saw's cutting process parameters.
基金Sponsored by the National Nature Science Foundation of China (50875179)
文摘In order to find out the contact pressure intensity distribution and its effects on the workepiece flatness error in plane polishing with retaining ring,the contact model and the boundary conditions are built up based on the axial symmetric elastic contact theory.The pressure intensity distribution is calculated and analyzed with the help of the Hankel transform theory and the constructing solution method of Chebyshev orthogonal polynomials.And then,the effects of the dimensionless ring-workpiece gap,the load ratio of the retaining ring and the dimensionless ring width on the contact pressure intensity distribution are obtained.Finally,based on the distribution theory of material removal volume,the effects of the pressure intensity distributions on the flatness errors of polished workpiece are also investigated experimentally.The results show that the contact pressure intensity distribution becomes more uniform and the better profile of polished workpiece can also be obtained,if the dimensionless ring-workpiece gap is reduced,the load ratio is selected as 0.6 to 0.85,and the dimensionless ring width is taken as 0.13 to 0.40.
