Application of Intelligent Technology in Building Electrical Lighting Project

The rapid development of intelligent technology has led to its introduction into the field of electrical lighting in buildings.It provides more technical support for system design,use,and management,and creates a comfortable and safe living environment.The adoption of intelligent technology enables the creation of an intelligent management system,where controllers and sensors are used to adjust the light source within the building,monitor and manage the lighting system in real time,monitor the energy consumption and safety of the system,and achieve the goal of energy saving and emission reduction.This paper briefly discusses the application and significance of intelligent technology in electrical lighting and puts forward design ideas to optimize electrical lighting and measures for lighting system management.

Research on Electrical Automation Control Design Based on PLC Technology

As science and technology continue to progress forward,electrical automation engineering is also developing,of which programmable logic controller(PLC)technology is widely being used.Through the integration of PLC technology and traditional electrical automation technology,good development of modern science and technology is promoted while traditional automation is preserved.The development of electrical engineering can greatly improve the strength of science,technology,and economy in our country.Based on PLC technology,this paper analyzes the design of electrical automation control.

The Challenges in Electrical and Electronic Technology Courses in Vocational Colleges

This paper addresses the challenges in the teaching of electrical and electronic technology in higher vocational colleges and proposes specific countermeasures to improve teaching quality and effectiveness.The countermeasures include optimizing teaching content,emphasizing practical application and innovation,innovating teaching methods,introducing modern instructional approaches,strengthening the teaching team,enhancing teacher quality and practical expertise,upgrading experimental equipment and facilities,enriching curriculum resources,and incorporating digital teaching materials.These measures aim to cultivate high-quality skilled talents,promote social and economic development,and enhance national competitiveness.By adjusting the course structure,incorporating real-world industry cases,and fostering collaboration with enterprises,students can better understand and apply electrical and electronic technology.The introduction of project-based teaching,flipped classrooms,and multimedia technology can enhance student engagement and facilitate independent learning.Furthermore,the improvement of experimental resources and the establishment of online teaching platforms can enhance students’practical skills and provide a variety of learning resources.These measures contribute to the overall improvement of electrical and electronic technology teaching in higher vocational colleges.

Teaching Design and Implementation of the Electrical and Electronic Technology Course Based on Teaching Ability Competition

The teaching ability competition is a vital method for stimulating teachers’enthusiasm and enhancing their teaching skills.This approach has gained increasing attention from colleges and universities in recent years.The competition focuses on evaluating teachers’capabilities in designing and implementing lessons,encouraging the exchange of new educational ideas and high-quality teaching methods.Reforming the teaching of Electrical and Electronic Technology courses based on insights from teaching competitions can significantly improve teaching quality.This paper explores the teaching design and implementation of the Electrical and Electronic Technology course,drawing on the principles of teaching ability competitions.First,it analyzes the existing problems in teaching this course.Then,it highlights the significant benefits that teaching competitions bring to the course.Based on these insights,the paper proposes practical strategies aimed at enhancing students’interest and practical skills,thereby promoting innovative developments in teaching Electrical and Electronic Technology.

An Improved Biometric Fuzzy Signature with Timestamp of Blockchain Technology for Electrical Equipment Maintenance

The power infrastructure of the power system is massive in size and dispersed throughout the system.Therefore,how to protect the information security in the operation and maintenance of power equipment is a difficult problem.This paper proposes an improved time-stamped blockchain technology biometric fuzzy feature for electrical equipment maintenance.Compared with previous blockchain transactions,the time-stamped fuzzy biometric signature proposed in this paper overcomes the difficulty that the key is easy to be stolen by hackers and can protect the security of information during operation and maintenance.Finally,the effectiveness of the proposed method is verified by experiments.

Roller Profile Online Measurement Based on Ultrasonic Circulation Pulse-echo Technology

In order to meet the high precision requirement of wide steel strip in industry field, a novel online measurement of roller profile based on sonic circulation and pulse-echo technology was introduced. All kinds of the factors influencing the accuracy of roller profile online measurement were analyzed in detail and error compensation analysis of system was accordingly presented. In order to reduce count error, field program gate array(FPGA) was introduced and a highprecision data acquisition system was designed based on digital phase-shift technology. Experiments indicate that the standard deviation of measure data was 7.27 μm, which showed the feasibility and validity of the proposed method, and realized the roll profile measurement with high precision.

Velocity Measurement and Freezing Technology of Multi-shot Pellet on HL-1M Tokamak

A measuring system for high-speed hydrogen ice pellet was introduced in this paper and the photographing of flying pellet taken therein. With the system, a pellet (minimum size of φ 0.3 mm) velocity (ranging from 50 m/s to 2500 m/s) can be measured in the HL-1M tokamak fueling experiments. By analyzing photographs and the conditions of frozen pellets (including gas supply, gas replenishment, temperature controlling etc), the pellet-freezing technology is summarized in the paper.

Traceability Technology of DC Electric Energy Metering for On-Site Inspection of Chargers

The on-site inspection of high-power DC chargers results in new DC high-current measurement and DC energy traceability system requirements.This paper studies the traceability technology of electric energy value for automotive high-power DC chargers,including:(1)the traceability method of the built-in DC energy meter and shunt of the charger;(2)precision DC high current and small precision DC voltage output and measurement technology.This paper designs a 0.1 mA∼600 A DC high current measurement system and proposes a 0.005 level DC powermeasurement traceability system.The uncertainty evaluation experiment of theDC powermeasurement calibration system and the high-power DC charger’s on-site calibration experiment results verify the method’s effectiveness and feasibility in this paper.The experimental results show that the combined standard uncertainty of the DC power metering verification system can be 0.0451%.

THE PROSPECTIVE OF NEW TECHNOLOGY DEVELOPMENT FOR SUSTAINABLE ELECTRIC POWER SUPPLY IN CHINA

China is a large developing country with rapid growth rate. To the year 2050, its electric power will be increased by six to eight times, reaching 1.5—1.8 TW total installed capacity. The development can not only rely on the existing technology, it is crucial to accelerate the new technology development. This article discusses the perspective of various new technologies from the available energy resources and the required increase of electric power.

Illumination and Voltage Dependence of Electrical Characteristics of Au/0.03 Graphene-Doped PVA/n-Si Structures via Capacitance/Conductance-Voltage Measurements

Au/n-Si （MS） structures with a high dielectric interlayer （0.03 graphene-doped PVA） are fabricated to investigate the illumination and voltage effects on electrical and dielectric properties by using capacitance-voltage （C-V） and conductance-voltage （G/w-V） measurements at room temperature and at 1 MHz. Some of the main electrical parameters such as concentration of doping atoms （ND）, barrier height （ ФB（ C - V） ）, depletion layer width （WD） and series resistance （Rs） show fairly large illumination dispersion. The voltage-dependent profile of surface states （Nss） and resistance of the structure （Ri ） are also obtained by using the dark-illumination capacitance （Cdark- Cm） and Nicollian-Brews methods, respectively, For a clear observation of changes in electrical parameters with illumination, the values of ND, WD, ФB（O- V） and Rs are drawn as a function of illumination intensity. The values of ND and WD change almost linearly with illumination intensity. On the other hand, Rs decreases almost exponentially with increasing illumination intensity whereas ФB（C - V） increases. The experimental results suggest that the use of a high dielectric interlayer （0.03 graphene-doped PVA） considerably passivates or reduces the magnitude of the surface states. The large change or dispersion in main electrical parameters can be attributed to generation of electron-hole pairs in the junction under illumination and to a good light absorption. All of these experimental results confirm that the fabricated Au/0.03 graphene-doped PVA/n-Si structure can be used as a photodiode or a capacitor in optoelectronic applications.

Advancement in Science and Technology Enhanced the Growth of China's Electric Power Industry

Within the seven years’ period from 1987 to 1994. the total installed capacity of China’s electric power industry doubled from 100 GW to 200 GW. This high rate of growth has imposed new and more stringent requirements on all the branches in the

Partial Discharge Measurement of OCP-Tapes in Rotating Electrical Machines

Nowadays, PD （partial discharge） measurements are a crucial part of the preventive maintenance of electrical equipment within high voltage engineering. Especially for electrical machines, both the supplier and the user are interested in the results of PD measurements. However, PDs hardly represent the cause of the failure, more likely they are claimed as the outcome of a failure. This paper deals with the insulation of a 6 kV electrical machine, whereas PD measurements were carried out at a single stator from wound coils. During manufacturing, these coils were equipped with different materials for the OCP （outer corona protection）. Using different PD measurement systems and different bandwidths, investigations of the PD behavior of the coils were carried out. Additionally, the surface resistivity of the corona protection was determined. As a result, conclusions for the correlations between the resistance of the OCP as well as the PD behavior are stated. Furthermore, the influence of using different measurement systems, different measuring circuits, and different bandwidths is shown.

Digital measurement of bone tumor volume by CT three-dimensional reconstruction technology

Objective To discuss the measurement of bone tumor volume on the basis of three dimensional images segmentation technology. Methods Twenty patients with lacunar bone tumor from Tianjin Hospital and Tongji Hospital were included in the

Structural Surface Crack Monitoring Method Based on Electrical Potential Technique and Modern Surface Technology

Crack monitoring plays a great role in modern structural health monitoring, however, most of the conventional crack inspections have disadvantages in terms of the accuracy, expense, reliability, durability and level of instrumentation required. Thus, development of a simple and reliable crack inspection technique that allows continuous monitoring has been desired. In this paper, electrical potential technique and modern surface technology are employed together to develop a new structural surface crack monitoring method. A special crack monitoring coating sensor based on electrical potential technique was deposited on the hot spot of the structure by modern surface technology. The sensor consists of three layers： the isolated layer, the sensing layer and the protective layer. The isolated layer is prepared by anodic oxidation technology, the sensing layer is made of ion plated copper, and the protective layer is made of silicone. The thickness of each layer is at micrometer magnitude. The electrical conductivity of the sensor is very stable, and the fatigue performance of the specimen with or without coating sensor is nearly unchanged. The crack monitoring experiment result shows that there are two sudden rises of the coating sensor electrical potential values, corresponding to different stages of the crack initiation and propagation. Since the width of the surface coating sensor is only 0.5 mm, this crack monitoring sensor can detect the propagation of cracks less than 0.5 mm long. The method proposed takes the simplicity of electrical potential technique and can monitor surface crack of nearly all kinds of structures precisely. The results of this paper may form the basis of a new crack monitoring system.

Application and Development of Electric Energg Storage Technology in China

This paper describes the background of disseminating and applying electric energy storage technology in China. Its present application status is introduced, including governmental support and guidance, analyses on economic benefits and typical projects, etc.

Application of Electrical Capacitance Tomography to the Concentration Measurement in a Cyclone Dipleg

Accurate solid concentration measurement plays a key role in the process industry. Measurements analyzed offline can be used to estimate process efficiencies, to identify problems in a flow, and to validate computational models. Online measurements can be used for active control. Electrical capacitance tomography （ECT） is a unique measuring technique with great potential in multiphase flow measurement. Experimental studies are carried out on a solid concentration measurement in a cyclone separator dipleg, using ECT. In this experiment eight electrodes are selected for the ECT sensor that is placed on the straight tube of the dipleg. The fluctuating characteristics according to the screw feeder and the effect of the airflow rate from the top of the cyclone are analyzed. The feasibility andreliability of the method are verified by the experimental results.

Detecting Impact Damage in Carbon Fabric/epoxy-matrix Composites by Ultrasonic F-scan and Electrical Resistance Measurement

The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact damage energy threshold value of carbon fabric/epoxy-matrix composites can determine by using ultrasonic F-scan. When the impact energy exceeds the threshold value, damage is generated in composites. Electrical resistance of impacted composites is changed owing to the contact of each carbon fiber unit in composites, which cause a change of the series-parallel in conductors. The veracity of detecting impact damage in composites can be improved in this case.

Research of Entropy-Based Overall Performance Measurement Model of Enterprises Technology Alliance

The performance measurement of enterprise technology alliances is complex.In this article,evaluation mechanism of entropy has been applied to it.Above all,performance connotation of enterprise technology alliance is defined from the aspect of self-organizatlon theory.Then,on dynamic and systerna-tical view,an entropy-based overall performance measurement model for technology alliance is established,using its life-cycle as the principal line,which includes initial condition evaluation,process e- valuation as well as benefit evaluation.Finally,a case study is carried out to the demonstration of that model.The author believes that an improved performance measurement model based on alliance life-cycle would be practicability to alliance.

On-line measurement of electrical variables of the transducer during ultrasonic welding and cutting

A measurement system for high power electrical variables with ultrasonic frequency was established. It can measure the effective values of the voltage and the current, the active power, the phase difference of voltage and current, the frequency of the transducer during ultrasonic welding and cutting. In sampling circuits of the system, the measured current is sensed by using a no capacitance and no inductance precision resistor and is treated with a difference amplifier, the measured voltage is processed by using a proportional amplifier. For achieving good amplitude frequency characteristics and rapid measurement of high frequency signals, the resistors, capacitors and amplifiers used in the system are rationally selected. Calibrating experiments show that relative errors are less than 1% for voltage and current effective values and less than 2.5% for active power, and absolute errors are ±1 Hz for frequency and ±1.7° for phase difference of voltage and current in the range of 17～23 kHz .