Numerical simulation of melt flow and temperature field during DC casting 2024 aluminium alloy under different casting conditions

Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during casting,which are crucial for the quality of the ingot and can determine the success or failure of the casting operation.Numerical simulation,with the advantages of low cost,rapid execution,and visualized results,is an important method to study and optimize the DC casting process.In the present work,a simulation model of DC casting 2024 aluminum alloy was established,and the reliability of the model was verified.Then,the influence of casting parameters on flow field and temperature field was studied in detail by numerical simulation method.Results show that with the increase of casting speed,the melt flow becomes faster,the depths of slurry zone and mushy zone increase,and the variation of slurry zone depth is greater than that of mushy zone.With an increase in casting temperature,the melt flow rate increases,the depth of the slurry zone becomes shallower,and the depth of the mushy zone experiences only minor changes.The simulation results further indicate that the increase of the flow rate of the secondary cooling water slightly reduces the depths of both slurry and mushy zone.

Investigation on Temperature Field Calibration and Analysis of Wind Tunnel

For wind tunnels,it is essential to conduct temperature and flow field calibration on their test section,which is an important indicator for evaluating the quality of wind tunnel flow fields.In the paper,a truss composed of temperature sensors was used to calibrate the temperature field of a completed wind tunnel section.By adjusting the distance between the temperature measurement truss and the nozzle,as well as the wind speed,the temperature field distribution data at different positions could be obtained.Analyze these data to identify important factors that affect the distribution of temperature field.Simultaneously,the temperature field of the wind tunnel was simulated accordingly.The purpose is to further analyze the fluid heat transfer between air and wind tunnel walls through numerical simulation.Through the above analysis methods,the quality of the temperature field in the wind tunnel has been further verified,providing reference for future wind tunnel tests of relevant models.

Numerical simulation of temperature and velocity fields in plasma spray

Based on the turbulence jet model, with respect to Ar-He mixture plasma gas injecting to ambient atmosphere, the temperature filed and velocity field under typical working conditions were investigated. Given the conditions of I=900 A, FAr= 1.98 m^3/h, FEe=0.85 m^3/h, it is found that both the temperature and the velocity undergo a plateau region near the nozzle exit （0-10 mm） at the very first stage, then decrease abruptly from initial 13 543 K and 778.2 m/s to 4 000 K and 260.0 m/s, and finally decrease slowly again. Meanwhile, the radial temperature and radial velocity change relatively slow. The inner mechanism for such phenomena is due to the complex violent interaction between the high-temperature and high-velocity turbulent plasma jet and the ambient atmosphere. Compared with traditional methods, the initial working conditions can be directly related to the temperature and velocity fields of the plasma jet by deriving basic boundary conditions.

Temperature Field in Laser Line Scanning Thermography: Analytical Calculation and Experiment

The temperature field in laser line scanning thermography is investigated comprehensively in this work,including analytical calculation and experiment.Firstly,the principle of laser line scanning thermography is analyzed.On this basis,a physical laser line scanning model is proposed.Afterwards,based on Fourier transform(FT)and segregation variablemethod(SVM),the heat conduction differential equation in laser line scanning thermography is derived in detail.The temperature field of the composite-based coatings model with defects is simulated numerically.The results show that the laser line scanning thermography can effectively detect the defects in the model.The correctness of the analytical calculation is verified by comparing the surface temperature distribution obtained by analytical calculation and numerical simulation.Additionally,an experiment is carried out and the changeable surface temperature obtained by analytical calculation is compared with the experimental results.It shows that the error of maximum temperature obtained by analytical calculation and by experiment is 8%with high accuracy,which proves the correctness of analytical calculation and enriches the theoretical foundation of laser line scanning thermography.

Numerical Simulation of Multi-track and Multi-layer Temperature Field on Laser Direct Metal Shaping

To improve the mechanical properties of the parts fabricated by Laser Direct Metal Shaping(LDMS),it is of great significance to understand the distribution regularities of transient temperature field during LDMS process.Based on the“el- ement birth and death”technique of finite element method,a three-dimensional multi-track and multi-layer model for the transient temperature field analysis of LDMS is developed by ANSYS Parametric Design Language(APDL)for the first time.In the fab- ricated modal,X-direction parallel reciprocating scanning paths is introduced.Using the same process parameters,the simulation results show good agreement with the microstructure features of samples which fabricated by LDMS.

EXPERIMENTAL RESEARCH AND NUMERICAL SIMULATION OF MOLD TEMPERATURE FIELD IN CONTINUOUS CASTING OF STEEL

Mold is the heart of the continuous casting machine. Heat transfer and solidification in a water- cooled mold are the most important factors during the continuous casting of steel. For studying the temperature distribution of a mold wall, a simulated apparatus of mold was designed and experiments were performed by it. The measured results indicated that the mold wall temperature approaches the temperature of cooling-water. An equivalent thermal-conductivity coefficient was proposed and deduced on the basis of the conclusion of the experiments. This coefficient was applied to solve the heat transfer between the melt and cooling water, and to characterize the heat transfer capacity of the mold. By this equivalent thermal-conductivity coefficient, it is very easy and convenient to numerically simulate the solidification process of continuous casting. And the calculation results are in agreement with the experiments. The effects of custing speed and water flow rate on the mold temperature field were also discussed.

Numerical simulation of wellbore and formation temperature fields in carbonate formations during drilling and shut-in in the presence of lost circulation

Temperature curves reflect geothermal gradients and local temperature anomalies, thus providing a new understanding of the underground reservoir conditions. When encountering caverns or fractures and fissures during drilling, lost circulation may occur and result in a change to the original formation temperature field, and in severe cases, even the conventional open hole well logging data cannot be obtained. This paper uses finite element analysis software COMSOL to establish a heat transfer model for the wellbore/reservoir formation system during drilling and shut-in in the presence of lost circulation, and a case study is made in a carbonate reservoir in the Tahe oilfield. On the basis of the above, we analyze the temperature distribution in the leakage zone, and the studies have shown that the leakage and petrophysical properties have an impact on the temperature of the wellbore and formation, hence we can estimate the reservoir permeability using the temperature data. In addition, the determination of the temperature recovery time after some drilling fluids have leaked into the formation will help in recognizing the subsurface temperature field of the carbonate formation correctly, thus enhancing production logging interpretation accuracy and improving the understanding of later measurements.

Frictional heat analysis of mine hoist and numerical simulation on temperature field of gasket

The frictional performance of gaskets is greatly affected by frictional heat in operational mine hoists. Based on frictional mechanism and heat transfer theory, the mathematical model of the temperature field of the PVC gasket in an operational mine hoist was investigated, a numerical simulation using ANSYS is presented and the distribution of the temperature and heat flux were studied under basic assumptions. The results show that the temperature gradually decreases as the radius of the model increases and the isotherms are arcs of concentric semi-circle. The heat flux is of bilateral symmetry in the model and decreases radially. The theoretical values correspond with the measured values for a short time (τ≤ 100 s) when the steel wire rope slides.

Numerical Simulation of Coupled Molten Steel Flow and Temperature Fields in Compact Strip Production Casting

Based on the casting manufacture practice of steel slabs by CSP technology, the flow and the temperature fields of the funnel mould and the secondary cooling segment were simulated using the commercial code, CFX4. Compared with other physical investigations, the correlative data of the present simulation results are in good agreement with them. Therefore, a more comprehensive survey for metallurgy characteristic of the flow and the temperature fields in CSP continuous casting process can be achieved.

Numerical Simulation of Temperature and Stress Fields of Ti-Alloy Thin-well Barrel during Quenching Process

The mathematical models have been established to describe the temperature and stress profiles in T16A14V cylinder during quenching. The residual stress and deformation of the workpiece can be predicted precisely based on ANSYS software. The simulated results show that the temperature of the divided element decreases faster at the edge than that at the internal of the workpiece during quenching from 1050 to 20°C. The largest temperature difference and dimension change in diameter are about 90°C and -0.935%, respectively. The position of largest tensile stress occurs around the edge of the cylinder.

Numerical simulation of temperature field during gas preheating and start-up of drained aluminum reduction cell

The method of numerical simulation was applied to investigate gas preheating and start-up process in a drained aluminum reduction cell. The transient temperature and velocity fields of a 156 kA drained aluminum reduction cell were numerically calculated. The results show that the method of gas preheating and bake-out can basically meet the technical requirements of the start-up process for the drained cell. If the same distributing scheme of gas nozzle as that in the general cells is used, there are problems of great temperature gradients and low temperature zone at the top of cathode near the side of nozzles. In order to promote the effect of gas preheating and baking the drained cell, the jetting angle of end nozzle is adjusted and the temperature distribution in the drained cell is obviously improved. By means of simulating the temperature field in the case that jetting angle varies from 0? to 30?, it is concluded that better temperature distribution can be obtained if the jetting angle of end nozzle is approximately 15?.

NUMERICAL SIMULATION AND ANALYSIS ON THE VELOCITY FIELD IN BATH OF A ROUND ELECTRIC CLEANING FURNACE

The flowing behavior of liquid slag has an important effect on the heat efficiency, recovery ratio ofvaluable metals and life span of the electric cleaning furnace. The velocity procedure using "κ-ε" model wasdeveloped under the cylindrical coordinate system. The procedure is used to calculate the velocity field ofmolten slag. The forces acting on molten slag were analyzed. The calculating method of electromagnetic forcewas described. The discrete equations, which were solved by using SIMPLE algorithm, were generated bymeans of interlace grids and control volume. The boundary layers near the solid wall were treated as wallfunction. The velocity distribution is obtained. The results show that the velocity of molten slag varies withdifferent horizontal sections. There are six eddies in the surface layer of molten slag. A large circle is formedin the sections below the electrodes, while the longitudinal section includes two large circles around the electrode. The influences of the features of the velocity field on the operation in the electric cleaning furnace arediscussed in detail.

SIMULATION OF TEMPERATURE AND THERMAL STRESS FIELD IN LASER MILLING PROCESSING

The physical model of temperature field and thermal stress field are established in this paper, on which the numerical simulation with the assuming physical and laser milling parameters have been finished. The laser milling process can be explained.

NUMERICAL SIMULATIONS OF TEMPERATURE FIELD IN DIRECT METAL LASER SINTERING PROCESS

A mathematical model is developed for simulating the heat transferring behavior in a direct metal laser sintering process. The model considers the thermal phenomena involved in the process, including conduction, radiation, and convection. A formula for the calculation of the heat conductivity of a sintering system containing solid phase, liquid phase, and gas phase is given. Due to the continuous movement of the laser beam, a local coordinate system centered on the laser beam is used to simplify the analytical calculation. Assuming that it is approximately a Gaussian laser beam, the heat conduction equation is resolved based on the assumption of the thermal insulating boundary conditions and the fixed thermal physical parameters. The FORTRAN language is employed to compile the program to simulate the temperature field in the direct copper powder sintering process. It shows a good agreement with the preliminary experimental results.[KH3/4D]

Temperature field and ventilation simulation of stope in Hongtoushan mine

Hongtoushan copper mine was studied by analyzing the type of heat source, the calculation method about thermal releasing in stope,thermal transfer between rock and air,distribution of temperature in stope were formulated.With CFD (Computational Fluid Dynamics,DFD) simulation and Fluent software,geometrical model of a stope was built,boundary conditions was initialized,then the temperature distribution,velocity and pressure field,concentration of oxygen and CO2 of air were simulated.In order to validate the simulation result,the parameters of the stope were measured with meter,and com- paring with the data of simulation.The result shows that the data of measuring and simu- lating are compatible.According to the distribution of temperature and velocity,some ways such as flow angle and flow velocity are put forward,simulation and parameter optimiza- tion made also,a satisfied result is acquired.The conclusion can be used on ventilation designing and stope improving.

The Effects of Thickness and Location of PCMon the Building’s Passive Temperature-Control–A Numerical Study

Building energy consumption and building carbon emissions both account for more than 20%of their total national values in China.Building employing phase change material(PCM)for passive temperature control shows a promising prospect in meeting the comfort demand and reducing energy consumption simultaneously.However,there is a lack of more detailed research on the interaction between the location and thickness of PCM and indoor natural convection,as well as indoor temperature distribution.In this study,the numerical model of a passive temperature-controlled building integrating the developed PCM module is established with the help of ANSYS.In which,the actual weather condition of Beijing city is set as the boundary conditions and the indoor natural convection is simulated with the consideration of radiation model.The effects of PCM’s thickness and location on the internal temperature field are analyzed and discussed.The results show that the room could maintain within the human comfort temperature range with the longest ratio of 94.10%and the shortest ratio of 51.04%as integrating PCM.In comparison,the value is only 26.70%without PCM.The room’s maximum temperature fluctuation can also be improved;it could be lowered by 64.4%compared to the normal condition.When the quantity of PCM is sufficient,further increasing the PCM amount results in a temperature fluctuation reduction of less than 0.1°C and does not increase the comfort time.Placing PCM on the wall induces an apparent variation in indoor temperature along the vertical direction.Conversely,placing PCM on the roof can lead to a heat transfer rate difference of up to seven times.The optimal placement of PCM depends on the difference between the environmental and phase change temperatures.If the difference is positive,placing PCM on the roof is more effective;conversely,the opposite holds.According to the results over the entire cycle,PCM application on vertical walls yields better performance.The significant difference in natural convection caused by the same thickness of PCM but different application positions,coupled with the influence of air movement on the melting and solidification of PCM,further impacts indoor temperature fluctuations and comfort.This study can provide guidance for the application location and thickness of PCM,especially for scenarios where temperature regulation is required at a specific time.

Numerical analysis for permafrost temperature field in the short term of permafrost subgrade filling

Purpose-It is of great significance to study the influence of subgrade filling on permafrost temperature field in permafrost area for the smooth construction and safe operation of railway.Design/methodology/approach-The paper builds up the model for the hydrothermal coupling calculation of permafrost using finite element software COMSOL to study how permafrost temperature field changes in the short term after subgrade filling,on which basis it proposes the method of calculation for the concave distortion of freezing front in the subgrade-covered area.Findings-The results show that the freezing front below the subgrade center sinks due to the thermal effect of subgrade filling,which will trigger hydrothermal erosion in case of sufficient moisture inflows,leading to the thawing settlement or the cracking of the subgrade,etc.The heat output of soil will be hindered the most in case of July filling,in which case the sinking and the distortion of the freezing front is found to be the most severe,which the recovery of the permafrost temperature field,the slowest,constituting the most unfavorable working condition.The concave distortion of the freezing front in the subgrade area increases with the increase in temperature difference between the filler and ground surface,the subgrade height,the subgrade width and the volumetric thermal capacity of filler,while decreases with the increase of the thermal conductivity of filler.Therefore,the filler chose for engineering project shall be of small volumetric thermal capacity,low initial temperature and high thermal conductivity whenever possible.Originality/value-The concave distortion of the freezing front under different working conditions at different times after filling can be calculated using the method proposed.

COUPLED NUMERICAL SIMULATION ON COLD ROLLER'S TEMPERATURE FIFLD-PHASE TRANSFORMATION - STRESS FIELD DURING ITS QUENCHING PSOCESS

Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time, and these variables take a contact interactions in the whole process. In this paper, a three dimensional non - linear mathematical model for queeching process has been founded and the numerical simulation on temperature field,microstructre and stress field has been realized.In the FEM analysis, the incremental iteration method is used to deal with such complicated nonlinear as boundary nonlinear, physical property nonlinear,transformation nonlinear etc.The effect of stress on transformation kinetics has been considered in the calculation of microstructure. In the stress field anal- ysis,a thermo- elasto - plastic model has been founded, which considers such factors as transforma- tion strain,transformation plastic strain, themal strain and the effect of temperature and transforma- tion on mechanical propertier etc. The transient temperature field, microstructure distribution and stress field of the roller on any time can be displayed vividly,and the cooling curve and the changes of stress on any position can also be given.

Numerical simulation of the temperature fields of stainless steel with different roller parameters during twin-roll strip casting

The temperature field of stainless steel during twin-roll strip casting was simulated by experiment and a finite element （FE） model. By comparing the measured result with the simulated values, it is found that they fit close to each other, which indicates this FE model is effective. Based on this model, the effects of roll gap （t） and roll radius （R） on solidification were simulated. The simulated results give the relationship between t or R and the position of the freezing point. The larger the t is and the smaller the R is, the closer the position of the freezing point is to the exit.

SIMULATION ON TEMPERATURE FIELD OF FRICTION STIR WELDED JOINTS OF 2024-T4 Al

The thermal model of FSW based on the thermal elastic-plastic finite element method, and the transient temperature distribution of FS welded joints of 2024-T4 Al was simulated by using this model, which provides useful information for the investigation of FSW process. Simulation resuits show that the temperature distribution of the weld gradually decreases toward periphery in a radiate format, whose center is the probe, and the highest temperature in the weld can reach about 400℃. The initial terminal of the weld is a zone, in which the temperature gradient is great, and defects of the welding are easily produced in this zone. Temperature change at the end of the welded joint is as layer variation, the local serious defects are not easy to produce in this zone.