Cross-upgrading of biomass hydrothermal carbonization and pyrolysis for high quality blast furnace injection fuel production:Physicochemical characteristics and gasification kinetics analysis

The paper proposes a biomass cross-upgrading process that combines hydrothermal carbonization and pyrolysis to produce high-quality blast furnace injection fuel.The results showed that after upgrading,the volatile content of biochar ranged from 16.19%to 45.35%,and the alkali metal content,ash content,and specific surface area were significantly reduced.The optimal route for biochar pro-duction is hydrothermal carbonization-pyrolysis(P-HC),resulting in biochar with a higher calorific value,C=C structure,and increased graphitization degree.The apparent activation energy(E)of the sample ranges from 199.1 to 324.8 kJ/mol,with P-HC having an E of 277.8 kJ/mol,lower than that of raw biomass,primary biochar,and anthracite.This makes P-HC more suitable for blast furnace injection fuel.Additionally,the paper proposes a path for P-HC injection in blast furnaces and calculates potential environmental benefits.P-HC of-fers the highest potential for carbon emission reduction,capable of reducing emissions by 96.04 kg/t when replacing 40wt%coal injec-tion.

Controllable Condensation of Aromatics and Its Mechanisms in Carbonization

In order to obtain liquefied products with higher yields of aromatic molecules to produce mesophase pitch,a good understanding of the relevant reaction mechanisms is required.Reactive molecular dynamics simulations were used to study the thermal reactions of pyrene,1-methylpyrene,7,8,9,10-tetrahydrobenzopyrene,and mixtures of pyrene with 1-octene,cyclohexene,or styrene.The reactant conversion rates,reaction rates,and product distributions were calculated and compared,and the mechanisms were analyzed and discussed.The results demonstrated that methyl and naphthenic structures in aromatics might improve the conversion rates of reactants in hydrogen transfer processes,but their steric hindrances prohibited the generation of high polymers.The naphthenic structures could generate more free radicals and presented a more obvious inhibition effect on the condensation of polymers compared with the methyl side chains.It was discovered that when different olefins were mixed with pyrene,1-octene primarily underwent pyrolysis reactions,whereas cyclohexene mainly underwent hydrogen transfer reactions with pyrene and styrene,mostly producing superconjugated biradicals through condensation reactions with pyrene.In the mixture systems,the olefins scattered aromatic molecules,hindering the formation of pyrene trimers and higher polymers.According to the reactive molecular dynamics simulations,styrene may enhance the yield of dimer and enable the controlled polycondensation of pyrene.

Construction of 3D porous Cu_(1.81)S/nitrogen-doped carbon frameworks for ultrafast and long-cycle life sodium-ion storage

Transition metal sulfides have great potential as anode mterials for sodium-ion batteries(SIBs)due to their high theoretical specific capacities.However,the inferior intrinsic conductivity and large volume variation during sodiation-desodiation processes seriously affect its high-rate and long-cyde performance,unbeneficial for the application as fast-charging and long-cycling SIBs anode.Herein,the three-dimensional porous Cu_(1.81)S/nitrogen-doped carbon frameworks(Cu_(1.81)S/NC)are synthesized by the simple and facile sol-gel and annealing processes,which can accommodate the volumetric expansion of Cu_(1.81)S nanoparticles and accelerate the transmission of ions and electrons during Na^(+)insertion/extraction processes,exhibiting the excellent rate capability(250.6 mA·g^(-1)at 20.0 A·g^(-1))and outstanding cycling stability(70% capacity retention for 6000 cycles at 10.0 A·g^(-1))for SIBs.Moreover,the Na-ion full cells coupled with Na_(3)V_(2)(PO_(4))_(3)/C cathode also demonstrate the satisfactory reversible specific capacity of 330.5 mAh·g^(-1)at 5.0 A·g^(-1)and long-cycle performance with the 86.9% capacity retention at 2.0 A·g^(-1)after 750 cycles.This work proposes a promising way for the conversionbased metal sulfides for the applications as fast-charging sodium-ion battery anode.

Preparation of Co/S co-doped carbon catalysts for excellent methylene blue degradation

S and Co co-doped carbon catalysts were prepared via pyrolysis of MOF-71 and thiourea mixtures at 800℃at a mass ratio of MOF-71 to thiourea of 1:0.1 to effectively activate peroxymonosulfate(PMS)for methylene blue(MB)degradation.The effects of two different mixing routes were identified on the MB degradation performance.Particularly,the catalyst obtained by the alcohol solvent evaporation(MOF-AEP)mixing route could degrade 95.60%MB(50 mg/L)within 4 min(degradation rate:K=0.78 min^(-1)),which was faster than that derived from the direct grinding method(MOF-DGP,80.97%,K=0.39 min^(-1)).X-ray photoelectron spectroscopy revealed that the Co-S content of MOF-AEP(43.39at%)was less than that of MOF-DGP(54.73at%),and the proportion of C-S-C in MOF-AEP(13.56at%)was higher than that of MOF-DGP(10.67at%).Density functional theory calculations revealed that the adsorption energy of Co for PMS was -2.94 eV when sulfur was doped as C-S-C on the carbon skeleton,which was higher than that when sulfur was doped next to cobalt in the form of Co-S bond(-2.86 eV).Thus,the C-S-C sites might provide more contributions to activate PMS compared with Co-S.Furthermore,the degradation parameters,including pH and MOF-AEP dosage,were investigated.Finally,radical quenching experiments and electron paramagnetic resonance(EPR)measurements revealed that ^(1)O_(2)might be the primary catalytic species,whereas·O~(2-)might be the secondary one in degrading MB.

Structural and microwave absorption properties of CoFe_(2)O_(4)/residual carbon composites

Electromagnetic interference,which necessitates the rapid advancement of substances with exceptional capabilities for bsorbing electromagnetic waves,is of urgent concern in contemporary society.In this work,CoFe_(2)O_(4)/residual carbon from coal gasification fine slag(CFO/RC)composites were created using a novel hydrothermal method.Various mechanisms for microwave absorption,including conductive loss,natural resonance,interfacial dipole polarization,and magnetic flux loss,are involved in these composites.Consequently,compared with pure residual carbon materials,this composite offers superior capabilities in microwave absorption.At 7.76GHz,the CFO/RC-2 composite achieves an impressive minimum reflection loss(RL_(min))of-43.99 dB with a thickness of 2.44 mm.Moreover,CFO/RC-3 demonstrates an effective absorption bandwidth(EAB)of up to 4.16 GHz,accompanied by a thickness of 1.18mm.This study revealed the remarkable capability of the composite to diminish electromagnetic waves,providing a new generation method for microwave absorbing materials of superior quality.

Carbonization mechanism of bamboo (phyllostachys) by means of Fourier Transform Infrared and elemental analysis

通过测定在200-600℃炭化竹材得到的固体产物的碳、氢、氧元素的含量及它们的红外光谱,研究了在炭化过程中竹材中半纤维素、纤维素及木素的变化规律。结果表明,结合元素分析,红外光谱分析方法是研究竹材炭化机理的有效手段。在200℃以前,竹材中的半纤维素和纤维素的大量羟基断裂,并结合成水而失去。在200-250℃之间,竹材中的纤维素被降解,其中的吡喃型环也遭到破坏。并且木素中的甲氧基也被脱去。竹材中的木素网状结构在250-400℃之间遭到完全的破坏。竹炭中的碳原子在600℃已基本上完成了芳环化。图3表2参15。

INFLUENCE OF HEAT TREATMENT ON OXIDATION PROPERTIES OF C/C COMPOSITES FABRICATED BY HIGH PRESSURE IMPREGNATION CARBONIZATION

Felt base carbon/carbon composites fabricated by super-high pressure impregnation carbonization process (SPIC) were heat treated at high temperature 2773K. The oxidation properties of felt base carbon/carbon composites were investigated at different temperatures (773-1173K), and the microstructures of carbon/carbon composites were studied by SEM and X-ray diffraction. The experimental results showed that the inter-laminar distance of (002) plane (d002) deceased while the microcrystalline stack height (Lc) increased. The oxidation rate of felt base carbon/carbon composites was invari-able at certain temperatures. The oxidation mechanism of carbon/carbon composites changed remarkably at the oxidation temperature 973K. At the initial oxidation stage of carbon/carbon composites, carbon matrix was oxidized much more rapidly than carbon felt.

Preparation and Characterization of Polyaniline Nanofibers by Template-free Method

In the presence of p-toluene sulfonic acid (TSA) as a dopant, polyaniline (PAni) nanofibers, (about 80^-65 nm in diameter) were successfully synthesized with a chemical template-free method. It was found that the formation probability, morphology, and diameter of the resulting PAni-TSA nanofibers were sensitive to the synthetic conditions, such as reaction temperature, the molar ratio of TSA to aniline, and the concentration of TSA in the polymerization media. The molecular structure was characterized by using the FT-IR, Raman spectra and X-ray diffraction, which shows that the main chain structure of PAni-TSA nanofibers was in agreement with that of granular PAni.

Facile synthesis of hierarchically porous carbons by controlling the initial oxygen concentration in-situ carbonization of ZIF-8 for efficient water treatment

The state-of-the-art approaches for adjusting the structural characteristics of porous carbons are the aftertreatments, which are complicated and time consuming. In this work, a facile approach was developed, i.e., controlling the initial oxygen concentration in-situ during the direct carbonization of zeolitic imidazole framework-8(ZIF-8), to adjust the pore structure and prepare hierarchically porous carbons. The introduction of oxygen can significantly affect the crystalline and pore structures of porous carbons, and promote the pore widening and the formation of mesopores. An appropriate initial oxygen concentration can notably enhance the surface area and mesopore volume of porous carbon, and then improve the adsorption capacity toward methylene blue(MB) dye from water by 3.4 times. The developed approach is more efficient at lower carbonization temperature.Moreover, the introduction of oxygen can increase the ratio of HO\\C_O groups on the carbon surface, leading to enhanced interaction with MB molecules and higher adsorption capacity toward MB. The as-prepared porous carbons exhibit superior adsorption capacities toward MB dye as compared to the reported ZIF-8 derived carbons. These findings would aid the development of porous carbon materials with high performance.

Augmenting Intrinsic Fenton-Like Activities of MOF-Derived Catalysts via N-Molecule-Assisted Self-catalyzed Carbonization

To overcome the ever-growing organic pollutions in the water system,abundant efforts have been dedicated to fabricating efficient Fenton-like carbon catalysts.However,the rational design of carbon catalysts with high intrinsic activity remains a long-term goal.Herein,we report a new N-molecule-assisted self-catalytic carbonization process in augmenting the intrinsic Fenton-like activity of metal-organic-framework-derived carbon hybrids.During carbonization,the N-molecules provide alkane/ammonia gases and the formed iron nanocrystals act as the in situ catalysts,which result in the elaborated formation of carbon nanotubes(in situ chemical vapor deposition from alkane/iron catalysts)and micro-/meso-porous structures(ammonia gas etching).The obtained catalysts exhibited with abundant Fe/Fe-Nx/pyridinic-N active species,micro-/meso-porous structures,and conductive carbon nanotubes.Consequently,the catalysts exhibit high efficiency toward the degradation of different organic pollutions,such as bisphenol A,methylene blue,and tetracycline.This study not only creates a new pathway for achieving highly active Fenton-like carbon catalysts but also takes a step toward the customized production of advanced carbon hybrids for diverse energy and environmental applications.

In-situ carbonization approach for the binder-free Ir-dispersed ordered mesoporous carbon hydrogen evolution electrode

A binder-free Ir-dispersed ordered mesoporous carbon（Ir-OMC） catalytic electrode has been prepared through a designed in-situ carbonization method, which involves coating resorcinol and formaldehyde mixtures with iridium precursors onto the three-dimensional nickel foam framework, followed by insitu calcination in Natmosphere at 800 ℃ for 3 h. This electrode shows a large surface area, ordered mesoporous structure and homogeneous distribution of metal nanoparticles. It presents good activity and stability towards hydrogen evolution reaction, which is attributed to the efficient mass and electron transport from the intimate contact among Ir nanoparticles, ordered mesoporous carbon matrix and 3 D conductive substrate. We hope that this in-situ carbonization synthetic route can also be applied to design more high-performance catalysts for water splitting, fuel cells and other clean energy devices.

Influence of coal properties on coal conversion processes-coal carbonization,carbon fiber production,gasification and liquefaction technologies:a review

Coal due to its relatively large quantities and wide distribution worldwide has generated renewed interest in research and development with the aim of establishing coal conversion technologies that are technically reliable,envi-ronmentally and economically feasible.It has proved to be a prominent energy source in emerging markets with increasing energy demand by accounting for the largest increase in the demand of energy amongst all other energy sources.Fur-thermore,with its higher mesophase content,coal tar is an appropriate raw material for precursors in the production of carbon fiber.However,whenever a material is put to use,it is important to be able to associate its properties to the behavioral characteristics during a conversion process so as to have a basis for opting for the material in a given process or adjusting the operating conditions in order to optimize the material utilization.Therefore,as with any other material,it is important to be able to relate the properties of coal to its utilization.A review was carried out on the influence of coal properties on four main utilization technologies:gasification,carbonization,liquefaction and carbon fibre production.Among several properties rank,type,mineral matter content,distribution of trace elements,structural composition and pore structure were found to be most influential on the behavior of coal during conversion processes.

Preparation and Characterization of Carbon Microspheres From Waste Cotton Textiles By Hydrothermal Carbonization

Carbon microspheres were prepared from waste cotton fibers by hydrothermal carbonization(HTC)with the addition of copper sulphate in this work.The important influence factors,temperature,concentration of copper sulphate,resident time were explored here.The smooth and regular carbon microspheres could be formed at 330°C with 0.15 wt%copper sulphate after 6 h from waste cotton fibers.The crystal structures of cotton fibers were destructed in a short resident time with 0.15 wt%copper sulphate from SEM images and XRD patterns of solid products.This strategy provides a new,mild and efficient method to prepare carbon microspheres from waste cotton fibers by HTC.FTIR spectra verified that the abundant functional groups existed on the surface of synthesized carbon microspheres.From XPS and element analysis results,the copper sulphate participated in the forming process of carbon microspheres indeed.The presence of copper sulphate in the carbon microspheres provided a possibility for the application in antibacterial field.Besides,the catalytic mechanism of copper sulphate on the hydrolysis and carbonization of waste cotton fibers were also discussed.In conclusion,the copper sulphate is an efficient agent for preparing carbon microspheres by HTC from waste cotton fibers.

Organotemplate-free Hydrothermal Synthesis of SUZ-4 Zeolite: Influence of Synthesis Conditions

Various conditions were investigated in detail for the novel organic template-free static hydrothermal synthesis of SUZ-4 zeolite in the presence of seeds. The obtained samples were characterized by XRD （X-ray diffraction）, SEM （scanning electron microscope）, TG （thermal gravimetric analysis）, ICP （inductively coupling plasma） elemental analysis, nitrogen sorption isotherm and surface area. The results show that pure SUZ-4 zeolites with high crystallinity are obtained in a broad window of synthesis conditions： seed mass concentration 0.2%-2%, SIO2/A1203 molar ratio 21 25, KOH/SiO2 molar ratio 0.33 0.43, H20/SiO2 molar ratio 7.14-38.1, aging time 24 h, crystallization temperature 160℃, and crystallization time 6-10 d. Also, crystallinity and size of the rod-like SUZ-4 zeolite crystals are found to alter with the conditions.

Breaking the temperature limit of hydrothermal carbonization of lignocellulosic biomass by decoupling temperature and pressure

Hydrothermal carbonization(HTC) of lignocellulosic biomass is a promising technology for the production of carbon materials with negative carbon emissions. However, the high reaction temperature and energy consumption have limited the development of HTC technology. In conventional batch reactors, the temperature and pressure are typically coupled at saturated states. In this study, a decoupled temperature and pressure hydrothermal(DTPH) reaction system was developed to decrease the temperature of the HTC reaction of lignocellulosic biomass(rice straw and poplar leaves). The properties of hydrochars were analyzed by scanning electron microscopy(SEM), Fourier transform infrared(FTIR) spectroscopy, X-ray photoelectron spectroscopy(XPS), Raman spectroscopy, X-ray diffraction(XRD), thermogravimetric analyzer(TGA), etc. to propose the reaction mechanism. The results showed that the HTC reaction of lignocellulosic biomass could be realized at a low temperature of 200℃ in the DTPH process, breaking the temperature limit(230℃) in the conventional process. The DTPH method could break the barrier of the crystalline structure of cellulose in the lignocellulosic biomass with high cellulose content, realizing the carbonization of cellulose and hemicellulose with the dehydration, unsaturated bond formation, and aromatization. The produced hydrochar had an appearance of carbon microspheres, with high calorific values, abundant oxygen-containing functional groups, a certain degree of graphitization, and good thermal stability. Cellulose acts not only as a barrier to protect itself and hemicellulose from decomposition, but also as a key precursor for the formation of carbon microspheres. This study shows a promising method for synthesizing carbon materials from lignocellulosic biomass with a carbon-negative effect.

Acid leaching decarbonization and following pressure oxidation of carbonic refractory gold ore

Carbonate decomposition of carbonic refractory gold ore and the following pressure oxidation were studied.In the carbonate decomposition procedure,the effects of liquid-to-solid ratio and reaction time on decomposition ratio of carbonate were investigated.The experimental result shows that the decomposition ratio of carbonate is 98.24%under the conditions of liquid-to-solid ratio of 5:1,Fe^(3+)concentration of 20 g/L,sulfuric acid concentration of 20 g/L,reaction temperature of 80 ℃ and reaction time of 2 h.Then,the slurry obtained from carbonate decomposition was put into the titanium autoclave for pressure oxidation leaching.Effects of liquid-to-solid ratio,temperature,time and oxygen partial pressure on sulfur oxidation ratio were studied during pressure oxidation.With the prolonged time,pyrite and arsenopyrite are oxidized to ferric subsulfate,hydrated ferric sulfate and jarosite,resulting in the increasing residue ratio.The residue ratio and the sulfur content in the residue can be decreased by ferric subsulfate dissolution.The oxidation ratio of the sulfur is 99.35% under the conditions of oxidation time of 4 h,temperature of 210 ℃,oxygen partial pressure of 0.8 MPa and stirring speed of 600 r/min.

Mass Transfer and Reaction Kinetics in the Carbonization of Magnesium Oxide from Light Calcined Magnesia with Mechanical Force Enhancement

The carbonization of magnesium oxide particles by CO2 was investigated using a stirring mill reactor. The effects of the system temperature, stirring rotation speed, influx rate of CO2 and initial diameter of the magnesium oxide particles on the carbonization process were determined, The results show that the system temperature and the stirring rotation speed are the most significant influencing factors on the carbonization rate. The determi-nation of critical decomposition temperature (CDT) gives the maximum carbonization rate with other conditions fixed. A theoretical model involving mass transfer and reaction kinetics was presented for the carbonization process. The apparent activation energy was calculated to be 32.8kJ·mol-1. The carbonization process is co-controlled by diffusive mass transfer and chemical reaction. The model fits well with the experimental results.

Template-free hydrothermal synthesis and gas-sensitivity of hollow-structured Cu_(0.3)Co_(2.7)O_(4) microspheres

Hollow-structured Cu_(0.3)Co_(2.7)O_(4) microspheres have been synthesized by a simple one-pot template-free hydrothermal method with copper sulfate,cobalt acetate and ammonia as raw materials.The products were characterized by powder X-ray diffraction,energy dispersive X-ray analysis,selected area electron diffraction,high-resolution transmission electron microscopy,scanning electron microscopy and BET measurements.The research results show that the hollow Cu_(0.3)Co_(2.7)O_(4) microspheres consist of single-crystalline nanocubes with the diameter of about 20 nm.The formation mechanism of hollow Cu_(0.3)Co_(2.7)O_(4) microspheres is suggested as Ostwald ripening in a solid-solution-solid process,and Cu_(0.3)Co_(2.7)O_(4) microspheres are mesoporous containing two pore sizes of 3.3 and 5.9 nm.The as-prepared Cu_(0.3)Co_(2.7)O_(4) sensors have optimal gas responses to 50×10^(−6) mg/m^(3) C_(2)H_(5)OH at 190℃.

Efficient catalytic removal of COS and H_(2)S over graphitized 2D micro-meso-macroporous carbons endowed with ample nitrogen sites synthesized via mechanochemical carbonization

Developing a suitable catalyst for the elimination of highly toxic carbonyl sulfide(COS)and hydrogen sulfide(H_(2)S) is of great significance in terms of industrial safety and environmental protection.We demonstrate here the facile synthesis of graphitized 2D micro-meso-macroporous carbons by one-step carbonization of a mixture of urea and glucose at 700–900℃.The as-synthesized graphitized catalysts,designated as 2DNHPC-x(x=urea/glucose mass ratio),are endowed with an ultra-high concentration(12.9–20.2 wt%)of stable and versatile nitrogen sites(e.g.pyrrole and pyridine)which are anchored on the surface via stable covalent bonding.As a result,the 2D-NHPC-x are active in catalytic hydrolysis of COS on pyrrolic N to H_(2)S,and the H_(2)S can be subsequently captured on pyridinic N and converted to elemental sulfur at ambient conditions over the same materials.Among the prepared catalysts,2D-NHPC-x can catalytically hydrolysize 91%of COS to H_(2)S at 30℃,whereas the conversion ratio over the common catalysts g-C_(3)N_(4)and Fe_(2)O_(3)are below 6.0%.Furthermore,these catalysts also exhibit H_(2)S conversion and sulfur selectivity of nearly 100%at 180℃with long-time durability,which is higher than those of the most reported carbonbased catalysts.In contrast,the H_(2)S capacities of activated carbon,ordered mesoporous carbons(OMC)and N-doped OMC are 3.9,1.5 and2.39 mmol g^(-1),respectively.Both the experimental and theoretical results are disclosed that 2D-NHPC-x are superior to the nitrogen-doped porous materials ever applied in simultaneous catalytic elimination of both COS and H_(2)S.

NMR studies of stock process water and reaction pathways in hydrothermal carbonization of furfural residue

Hydrothermal carbonization(HTC) is a valuable approach to convert furfural residue(FR) into carbon material. The prepared biochars are usually characterized comprehensively, while the stock process water still remains to be studied in detail. Herein, a NMR study of the main components in stock process water generated at different HTC reaction conditions was reported. Various qualitative and quantitative NMR techniques(~1H and ^(13)C NMR,~1H-~1H COSY and ~1H-^(13)C HSQC etc.) especially 1D selective gradient total correlation spectroscopy(TOCSY NMR) were strategically applied in the analysis of HTC stock process water. Without separation and purification, it was demonstrated that the main detectable compounds are 5-hydroxymethylfurfural, formic acid, methanol, acetic acid, levulinic acid, glycerol, hydroxyacetone and acetaldehyde in this complicate mixture. Furthermore, the relationship between the concentration of major products and the reaction conditions(180-240 ℃ at 8 h, and 1-24 h at 240 ℃) was established. Finally, reasonable reaction pathways for hydrothermal conversion of FR were proposed based on this result and our previously obtained characteristics of biochars. The routine and challenging NMR methods utilized here would be an alternative other than HPLC or GC for biomass conversion research and can be extended to more studies.