Analysis of stresses at the center of transversely isotropic Brazilian disk

This article presents the stresses at the center of a Brazilian disk(BD)for transversely isotropic rocks.It is shown that the solution of stresses at the center of an anisotropic disk is a function of the disk radius and the magnitude of applied load,as well as the material orientation with respect to the load axis and two dimensionless ratios with specific physical meanings and limitations.These two dimensionless parameters are the ratios of Young’s modulus and apparent shear modulus,although the ratio of apparent shear modulus will be eliminated if the Saint-Venant assumption is considered.Considerable finite element simulations are carried out to find the stresses at the disk center concerning the material orientation and the two dimensionless parameters.Also,an approximate formula obtained from analytical results,previously proposed in the literature for solving the tensile and compressive stresses at the disk center,is re-written and simplified based on these new definitions.The results of the approximate formula fitted to the analytical results are compared to those obtained from numerical solutions,suggesting a good agreement between the numerical and analytical methods.An approximate equation for the shear stress at the disk center is also formulated based on the numerical results.Finally,the influence of the assumptions for simplification of the proposed formula for the tensile,compressive,and shear stresses at the disk center is discussed,and simple and practical equations are proposed as estimations for the stresses at the center of the BD specimen for low to moderate anisotropic rocks.For highly anisotropic rocks,the reference plots can be used for more accuracy.

Stress and strain analysis on the anastomosis site sutured with either epineurial or perineurial sutures after simulation of sciatic nerve injury

The magnitude of tensile stress and tensile strain at an anastomosis site under physiological stress is an important factor for the success of anastomosis following suturing in peripheral nerve injury treatment. Sciatic nerves from fresh adult cadavers were used to create models of sciatic nerve injury. The denervated specimens underwent epineurial and perineurial suturing. The elastic modulus （40.96 ＋ 2.59 MPa） and Poisson ratio （0.37 ＋ 0.02） of the normal sciatic nerve were measured by strain electrical measurement. A resistance strain gauge was pasted on the front, back left, and right of the edge of the anastomosis site after suturing. Strain electrical measurement results showed that the stress and strain values of the sciatic nerve following perineurial suturing were lower than those following epineurial suturing. Scanning electron microscopy revealed that the sciatic nerve fibers were disordered following epineurial compared with perineurial suturing. These results indicate that the effect of perineurial suturing in sciatic nerve injury repair is better than that of epineurial suturing.

Numerical Simulation of Stress Field in Physical Tempering Process of Flat Soda Lime Silica Glass

Based on the analysis of different theory for glass tempering process,the“structural theory”with stress relaxation and structural relaxation effects was selected to investigate the tempering of flat glass quantificationally.The geometrical model with small size and non-homogeneous mesh were considered to build the finite element models according to the characteristics of stress field.The tempering process of flat glass with12 mm thickness was calculated with the verified finite element model.The transient and permanent stress of the central area,edge and corner end of the flat glass are obtained and analyzed.From the calculation results of basic case,the transient tensile stress at the upper surface of the central area,the center point of edge,the edge of edge,the edge of corner were 14.30,18.94,40.76 and 34.75 MPa,respectively.The transient tensile stress at these points were dangerous to promote the glass to break during the tempering.In addition,the point at the diagonal line of symmetry plane in the thickness direction,which is 14 mm from corner,has the maximum permanent tensile stress about 70.01 MPa in the flat glass after tempering.Thus,it is indicated that the corner is the weakest region in the tempered glass.

EFFECT OF TENSILE STRESS AND RESIDUAL STRESS ON THE SPONTANEOUS STRAY FIELD SIGNALS FROM THE SURFACE OF 0.45%C STEEL

In order to explore the quantitative method of metal magnetic memory testing（MMMT） and clarify the relationship between Hp（y）, the normal component of spontaneous stray field, and applied stress or residual stress, the static tensile tests of 0.45%C steel sheet specimens are carried out on a servo hydraulic MTS810 machine. Hp（y） values are measured during the test process by an EMS-2003 metal magnetic memory diagnostic apparatus and a non-magnetic electric control displacement instrument. Residual stresses of some points on the surface of a specimen are measured by a Stress Tech X-Stress 3000 X-ray diffraction instrument. The results show that the same variation rules of Hp（y） value versus applied tensile stress are presented under the different conditions of load-on and load-off. However, the same rule does not exist between the Hp（y） value and residual stress. The variation of Hp（y） value reflects the history of applied tensile stress.

Tensile Stress Induced Phase Transformations in Zn-Al Alloy

Both furnace cooled and as-cast eutectoid Zn-Al alloys were investigated under external tensile stress at 100℃. It was observed that the external tensile stress caused decomposition of two metastable phases η'T and η'S which derived from both original state of the alloy, and a phase transformation, αf +ε→T' +η， in both furnace cooled and as-cast eutectoid Zn-Al alloys. Also spheroidized structure formed partially during tensile testing. Superplasticity of the alloy has been discussed correlating with the phase transformations and microstructural changes.

Experimental research on creep behaviors of sandstone under uniaxial compressive and tensile stresses

The consideration of time dependence is essential for the study of deformation and fracturing processes of rock materials, especially for those subjected to strong compressive and tensile stresses. In this paper, the self-developed direct tension device and creep testing machine RLW-2000M are used to conduct the creep tests on red sandstone under uniaxial compressive and tensile stresses. The short-term and long-term creep behaviors of rocks under compressive and tensile stresses are investigated, as well as the long-term strength of rocks. It is shown that, under low-stress levels, the creep curve of sandstone consists of decay and steady creep stages; while under high-stress levels, it presents the accelerated creep stage and creep fracture presents characteristics of brittle materials. The relationship between tensile stress and time under uniaxial tension is also put forward. Finally, a nonlinear viscoelastoplastic creep model is used to describe the creep behaviors of rocks under uniaxial compressive and tensile stresses.

Film-induced Tensile Stress during CorrosionProcess for α-Ti

The α-Ti foil with protective layer in one side bended to corrosion surface gradually during corrosion process in 0.1 mol/L H2SO4, while the passive film was formed, i.e., a tensile stress was developed in the surface layer of the sample. The extra tensile Stress grew gradually, whose maximum value is =313 MPa (average of 5 samples), which is near or reaches the yield stress. The extra tensile stress would be added to the load Stress during SCC to facilitate the emission and motion of dislocation, so that SCC cracks could nucleate in lower Stress(or lower KI).

Experimental investigation of electrode cycle performance and electrochemical kinetic performance under stress loading

Lithium-ion batteries suffer from mechano–electrochemical coupling problems that directly determine the battery life. In this paper, we investigate the electrode electrochemical performance under stress conditions, where seven tensile/compressive stresses are designed and loaded on electrodes, thereby decoupling mechanics and electrochemistry through incremental stress loads. Four types of multi-group electrochemical tests under tensile/compressive stress loading and normal package loading are performed to quantitatively characterize the effects of tensile stress and compressive stress on cycle performance and the kinetic performance of a silicon composite electrode. Experiments show that a tensile stress improves the electrochemical performance of a silicon composite electrode, exhibiting increased specific capacity and capacity retention rate, reduced energy dissipation rate and impedances, enhanced reactivity, accelerated ion/electron migration and diffusion, and reduced polarization. Contrarily, a compressive stress has the opposite effect, inhibiting the electrochemical performance. The stress effect is nonlinear, and a more obvious suppression via compressive stress is observed than an enhancement via tensile stress. For example, a tensile stress of 675 k Pa increases diffusion coefficient by 32.5%, while a compressive stress reduces it by 35%. Based on the experimental results, the stress regulation mechanism is analyzed. Tensile stress loads increase the pores of the electrode material microstructure, providing more deformation spaces and ion/electron transport channels. This relieves contact compressive stress, strengthens diffusion/reaction, and reduces the degree of damage and energy dissipation. Thus, the essence of stress enhancement is that it improves and optimizes diffusion, reaction and stress in the microstructure of electrode material as well as their interactions via physical morphology.

Retarded thermal oxidation of strained Si substrate

Strained Si is recognized as a necessary technology booster for modem integrated circuit technology. However, the thermal oxidation behaviors of strained Si substrates are not well understood yet despite their importance. In this study, we for the first time experimentally find that all types of strained Si substrates （uniaxial tensile, uniaxial compressive, biaxial tensile, and biaxial compressive） show smaller thermal oxidation rates than an unstrained Si substrate. The possible mechanisms for these retarded thermal oxidation rates in strained Si substrates are also discussed.

An Overview of Techniques for Measuring Residual Stress in Metal Matrix Composites

Measurement of residual stress is significant to ensure safety, reliability and the life of composites, and currently has been a hot issue in scientific research. The fabrication processes such as machining, and heat treatment inherit either kind of residual stress which had either positive consequences or negative ones, for example, the fatigue limit of a component enhances by compressive stress, whereas corrosion resistance gets reduced by tensile stress. This study is aimed at a brief overview of the recent advancement in this field to help researchers in the in-depth study of measuring residual stress. It helps them in selecting the most appropriate techniques among destructive methods i.e., mainly Contour, ring core, deep hole-drilling method, and non-destructive techniques i.e., diffraction, ultrasonic method, depending on their requirements and applications. For each available technique, working methodology, physical limitations, and applications are discussed. At the end of this paper, future trends regarding an assessment of residual stress have been forecasted.

Synergistic Effects of Gamma Irradiation,Tensile Stress and Moisture on the Radiolysis of Silicone Foam

The present work involves the investigation of the synergistic effects of gamma irradiation,tensile stress and absorbed moisture on the radiolysis behaviors of silicone foams by experiments and theoretical simulations.For both the pristine and dehydrated samples,the permanent tensile set increases with the initial tensile strain.Further analysis uncovers that the dehydrated samples exhibit greater permanent tensile sets,lower further elongation and higher Young’s modulus than the counterparts of the pristine samples with the same initial tensile strain and gamma dose,verifying the vital synergistic effects on crosslinking network and aggregation structures caused by moisture and gamma radiation.The synergistic effects unveiled by reactive molecular dynamics at the atomic scale are due to the moisture-induced neutralization and stabilization of the macromolecular radicals.The steric hindrance of moisture located at the interface of silica and polymer chains also conduces to the observed synergistic effects due to the inhibited crosslinking reactions.

Chloride Resistance of Concrete under Complex Stress and Environment

The presence of stress is shown to have a significant impact on chloride ions in concrete. Reinforced concrete is usually durable and cost-effective which has resulted in its widespread use for construction, however, the concrete subjected to environment and load has become increasingly apparently that attacked by aggressive agents such as chloride ion. In this study, the coupling influences are stress effects and environmental problems on the coastline concrete durability have been investigated. A series of cyclic of a wet-dry cycle and submersion tests were performed onto the stressed concrete to obtain an understanding of the physical mechanisms causing the accumulation of chlorides in the interior pores of concrete under different stress types and exposure environments, based on the same duration. Specimens were prepared and subjected to NaCl solution in a wet-dry cycle and submersion, the chloride in the tension zone is gradual with increasing the stress level, as well as the chloride ion in the wet-dry cycle, is increasing the number of cycles. The apparent diffusion coefficient of each specimen was calculated respectively, the profile of concentration at a different section of tension and compression zones were presented in influence factors of the number of cycles, the length of drying phase, and periodic wetting cycles with sodium solution was discussed. After employed Fick’s second law, the results suggested Da in a wet-dry cycle is much higher than the Da in submersion zones.

TENSILE PROPERTIES AND CREEP RESISTANCE OF AZ91 ALLOY CONTAINING ANTIMONY

Small amount of antimony addition to the Mg-9Al-0.8Zn-0.2Mn(AZ91) alloy results in the obvious increase of tensile strength at both ambient and elevated temperatures. The creep resistance at the temperatures up to 200°C is also improved significantly by antimony addition. Microstructural observations revealed that the addition of antimony modifies morphology of the β(Mg17Al12) phase and causes the formation of some rod-shaped precipitates Mg3Sb2 at grain boundaries. These precipitates have high thermal stability and play an important role for strengthening grain boundaries at elevated temperatures.

Microstructural,Mechanical,Electrical,and Thermal Properties of the Bi-Sn-Ag Ternary Eutectic Alloy

The development of lead-free solders has emerged as one of the key issues in the electronics packaging industries.Bi-Sn-Ag eutectic alloy has been considered as one of the lead-free solder materials that can replace the toxic Pb-Sn eutectic solder without increasing soldering temperature.We investigated the effects of temperature gradient and growth rate on the mechanical,electrical and thermal properties of the BiSn-Ag ternary eutectic alloy.Bi-47 wt%Sn-0.68 wt%Ag alloy was directionally solidified upward with different temperature gradients（G=2.33-5.66 K/mm） at a constant growth rate（V=13.25 μm/s） and with different growth rates（V=6.55-132.83 μm/s） at a constant temperature gradient（G=2.33 K/mm） in the growth apparatus.The microstructures（λ）,microhardness（HV）,tensile stress（σ）,electrical resistivity（ρ）,and thermal properties（△H,Cp,Tm） were measured on directionally solidified samples.The dependency of the λ,HV,σ,and ρ on G and V was investigated.According to the experimental results,X values decrease with increasing G and V,but HV,λ,and ρ values increase with increasing G and V.Variations of electrical resistivity（ρ） for cast samples with the temperature in the range of 300-400 K were also measured by using a standard dc four-point probe technique.The enthalpy of fusion（△H） and specific heat（Cp） for the same alloy was also determined by means of differential scanning calorimeter（DSC） from heating trace during the transformation from eutectic liquid to eutectic solid.

Moiré method analysis for tensile strain field of 2024 aluminum alloy welded joint

Using experimental mechanics method of moiré analysis, strain field distributions of 2024 aluminum alloy welded joints under different conditions were investigated. The results show that moiré stripes of welded joint without trailing peening just before fracture are not only few and scattered but also uneven, and the stress mainly concentrates on the poor position welded toes during the tensioning process with the relatively poor mechanical properties of welded joints; When the method of welding with trailing peening is adopted, moiré stripes of welded joint just before fracture are relatively thick and even due to the strengthening welded toes during the welding process, and fracture position transfers from the welded toes to weld, at the same time the mechanical properties of welded joints are improved greatly than conventional welding which can show that the technology of trailing peening is effective to strengthen welded joints of aluminum alloy with high strength.

MECHANICAL ANALYSIS OF CYLINDERS BEING UPSET BETWEEN SPHERICAL CONCAVE PLATEN AND CONCAVE SUPPORTING PLATE

Mechanical analysis of cylinders being upset between spherical concave platen and concave supporting plate is conducted. Rigid-plastic mechanical models for cylinders are presented. When the ratio of height to diameter, is larger than 1, there exists two-dimensional tensile stress in the deformed body, when the ratio is smaller than 1, there exists shear stress in static hydraulic zone. The former breaks through the theory that there is three-dimensional compressive stress irrespective of any ratio of height to diameter. The latter satisfactorily explains the mechanism of layer-like cracks in disk-shaped forgings and the flanges of forged gear axles. The representation of the two models makes the upsetting, theory into correct and perfect stage.

Self-healing of engineered cementitious composites at simulated summer conditions

Self-healing of engineered cementitious composites(ECC) subjected to a cyclic drying and wetting regime simulated summer outdoor environment was investigated in this paper.Uniaxial tension tests were used to generate multiple cracks in ECC specimens deformed to varying tensile strains.To quantify self-healing,resonant frequency measurements were conducted throughout drying-wetting cycles followed by tensile testing of self-healing ECC specimens.It was found that through self-healing the resonant frequency of ECC can recover 81% to 90% of initial values while showing a distinct rebound in stiffness of cracked ECC after self-healing.For specimens pre-loaded to high levels of strain between 2% and 3%,the tensile strain after self-healing can recover from 1.8% to 2.2%.Also,the effects of temperature during cyclic regime can lead to an increase in the ultimate strength of the material while slightly decreasing the strain-hardening capacity of ECC due to further hydration of unreacted cement and fly ash.

Synergistic passivation of MAPbI_(3) perovskite solar cells by compositional engineering using acetamidinium bromide additives

For the global commercialization of highly efficient and stable perovskite solar cells(PSCs),it is necessary to effectively suppress the formation of various defects acting as nonradiative recombination sources in perovskite light-harvesting materials.Interfacial defects between the charge-selective layer and the perovskite are easily formed in the solution process used to fabricate perovskite films.In addition,owing to the difference in thermal expansion coefficients between the substrate and the perovskite film,internal residual tensile stress inevitably occurs,resulting in increased nonradiative recombination.Herein,a simple compositional engineering scheme for realizing efficient and stable PSCs,which incorporates acetamidinium bromide(AABr)as an additive into the MAPbI_(3) lattice,is proposed.As an additive,AABr has been found to provide synergistic multiple passivation for both internal and interfacial defects.AABr was found to effectively release the tensile strain of the MAPbI_(3) film by forming a structure stabilized by NH-I hydrogen bonds,as evidenced by calculations based on density functional theory(DFT).Furthermore,the incorporated AABr additives created a charge carrier recombination barrier to enhance charge collection capability by reducing interfacial defects.Accordingly,a power conversion efficiency(PCE)of 20.18%was achieved using a planar device employing AABr-incorporated MAPbI_(3).This was substantially higher than the 18.32% PCE of a pristine MAPbI_(3)-based device.Notably,unencapsulated PSCs using AABr-incorporated MAPbI_(3) absorbers exhibited excellent long-term stability,maintaining>95% of initial PCE up to 1200 hours in ambient air.

Electronic and magnetic properties of single-layer and double-layer VX_(2)(X=Cl,Br)under biaxial stress

First-principles calculations and Monte Carlo simulations reveal that single-layer and double-layer VX_(2)(X=Cl,Br)can be tuned from antiferromagnetic(AFM)semiconductors to ferromagnetic(FM)state when biaxial tensile stress is applied.Their ground states are all T phase.The biaxial tensile stress at the phase transition point of the double-layer VX_(2) is larger than that of the single-layer VX_(2).The direct band gaps can be also manipulated by biaxial tensile stress as they increases with increasing tensile stress to a critical point and then decreases.The Neel temperature(´TN)of double-layer VX_(2) are higher than that of single-layer.As the stress increases,the TN of all materials tend to increase.The magnetic moment increases with the increase of biaxial tensile stress,and which become insensitive to stress after the phase transition points.Our research provides a method to control the electronic and magnetic properties of VX_(2) by stress,and the single-layer and double-layer VX_(2) may have potential applications in nano spintronic devices.

A NONLOCAL THEORY FOR BRITTLE FRACTURE

In this paper,a nonlocal theory of fracture for brittle materials has been systematically devel- oped,which is composed of the nonlocal elastic stress fields of Griffith cracks of mode-Ⅰ,Ⅱ and Ⅲ,the asymptotic forms of the stress fields at the neighborhood of the crack tips,and the maximum tensile stress criterion for brittle fracture.As an application of the theory,the fracture criteria of cracks of mode-Ⅰ,Ⅱ, Ⅲ and mixed mode Ⅰ-Ⅱ,Ⅰ-Ⅲ are given in detail and compared with some experimental data and the theoretical results of minimum strain energy density factor.