Experimental Study of the Influence of Intrinsic Parameters on the Thermal Reactivity of Sawdust, Polyethylene Terephthalate and Composite

Several works have been based on the study of thermal variations in biomass to derive more valuable products such as fuels capable of replacing oil in the event of a crisis or activated carbon used as an adsorbent material, widely used in industry for the elimination of unwanted materials, both in liquid and gaseous environments. A study of thermal parameters such as: heating speed, retention time, drying temperature, carbonization temperature, particle size, was carried out with the aim of determining the characteristic factors of the carbonization of Polyethylene terephthalate (PET), sawdust (SC) and sawdust/polyethylene terephthalate (CPS) mixture. The results of the immediate analysis revealed a very low level of ash in PET (0.013%) compared to the level of ash in sawdust (2.9%), as well as a high level of fixed carbon (82.960%), which suggests the presence of mineral oxides and a significant carbon matrix unlike PET, which indicates a very significant organic matrix (essentially made up of organic matter) with the absence of mineral oxides. The study of thermal parameters showed the water loss from Sawdust (SC) and the Sawdust/Polyethylene terephthalate (CPS) mixture, an increase with temperature, unlike that of PET whose variation is essentially zero. Without heat treatment, sawdust alone contains approximately 7% water. The optimal drying temperature for this study is 110˚C for a stay of 24 hours. It appears that the largest mass losses for the PET samples are between 87.19% and 96.05%, followed by that of the mixture, between 47.33% and 64.37%. And the lowest are observed, those of sawdust (from 24.02% to 62.6%). However, here we can say that the influence of the mass is not great, given the slight difference between the losses by temperature. The results of the study of the influence of grain size showed that the differences are insignificant, even if we vary the diameter of the grains from simple to triple. To better minimize physical constraints such as the intragranular diffusibility of the volatile matter and the homogeneity of the temperature in the grains, 75 μm particles are found to be optimal for our study. It can be noted when studying the heating rate that the mass loss at the end of the reaction is approximately the same depending on each precursor material. However, it has been demonstrated that the heating rate strongly influences the nature of the reaction products both for volatile materials and for the solid residue as well as on the kinetic parameters of the chemical reaction. Furthermore, the variation in apparent density shows a decrease as a function of the increase in the residence time of the materials in the reactor. As the carbonization time increases, the apparent density decreases. We note, for the lignocellulosic material, that the apparent density stabilizes after 60 minutes.

Effect of Polyethylene Terephthalate Plastic Waste on the Physico-Mechanical and Thermal Characteristics of Stabilized Laterite Bricks

The present work investigated the effect of polyethylene terephthalate (PET) plastic waste on the physico-mechanical and thermal properties of cement-stabilized laterite bricks to see the durability of the modified bricks (CSLB). Samples were formulated by mixing laterite, cement, and different percentages of PET (0%, 3%, 5%, and 7%) by volume. The bricks were produced using the M7MI Hydraform standard interlocking block and kept in the shade for a curing period of 28 days. The addition of 3% to 5% PET to the laterite stabilized with 10% cement results in a decrease in both dry and wet compressive strength, which is determined using the Controlab compression machine. However, the obtained results are in concordance with the standards. The thermal conductivity of CSLB, determined using the box method with the EI700 measurement cell, decreases as the PET content of the mixture increases. A decrease in bulk density from 1.67 to 1.58 g/cm3 was observed.

Synthesis of Activated Carbon from Polyethylene Terephthalate(PET)Plastic Waste and Its Application for Removal of Organic Dyes from Water

Synthetic plastics are often considered to be materials that cannot be broken down by natural processes.One such plastic,polyethylene terephthalate(PET),is commonly used in everyday items but when these products are discarded,they can cause serious harm to the environment and human health.In this study,PET plastic waste was used to create activated carbon using a physical activation process that involved using CO2 gas.The researchers investigated the effects of different temperatures,carbonization,and activation times on the resulting activated carbon’s surface area.The activated carbon was then analyzed using scanning electron microscopy(SEM),X-ray diffraction(XRD),FTIR,and BET.The activated carbon created from PET plastic waste showed excellent absorption properties for methylene blue in aqueous solutions across a wide range of pH levels.By creating activated carbon from plastic waste,not only are environmental issues addressed,but high-value activated carbon is produced for environmental remediation purposes.

Synthesis and identification of dinitro- and diaminoterephthalic acid

Dinitroterephthalic acid （DNTPA） and diaminoterephthalic acid （DATPA） were prepared in 85% and 75% yields, respectively. These compounds were characterized by using FTIR and ^1HNMR. DATPA can be used as a monomer for the preparation of polyesters and polyamides. 2009 H. Migbani. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

Recycling and depolymerization of waste polyethylene terephthalate bottles by alcohol alkali hydrolysis

In this work,a novel alcohol alkali hydrolysis method was explored for the preparation of terephthalic acid(TPA)from waste polyethylene terephthalate(PET).First,a series of single factor experiments on the depolymerization rate of waste PET bottles and the yield of TPA were conducted to determine the optimized experimental conditions,in terms of reaction time,reaction temperature,dosage of ethylene glycol and sodium bicarbonate,amount of distilled water and stirring rate.Then IR spectra and elemental analysis were carried out for the characterization of obtained product.Under optimal experimental conditions,over 98%PET can be depolymerized into the target product(TPA)and the purity and yield of TPA are over 97%and 94%,respectively.Both the experimental and analytical results support a feasible process for the preparation of TPA from waste PET.It is expected that this alcohol alkali hydrolysis method can promise an effective way for the sustainable recycling of waste PET.

Studies on the Simultaneous Synthesis of Dimethyl Carbonate and Poly(ethylene terephthalate): I. Catalytic Activity of Metal Acetate in Transesterification of Ethylene Carbonate with Dimethyl Terephthalate

A novel direct method for preparation of dimethyl carbonate and poly（ethylene terephthalate） from ethylene carbonate and dimethyl terephthalate has been demonstrated in the presence of metal acetate catalysts, lithium acetate dihydrate showed highest catalytic activity with 47.9% yield of dimethyl carbonate. This method was a green chemical process.

Simultaneous Synthesis of Dimethyl Carbonate and Poly（ethylene terephthalate） Using Alkali Metals as Catalysts

Dimethyl carbonate （DMC） and poly（ethylene terephthalate） was simultaneously synthesized by the transesterification of ethylene carbonate （EC） with dimethyl terephthalate （DMT） in this paper. This reaction is an excellent green chemical process without poisonous substance. Various alkali metals were used as the catalysts. The results showed alkali metals had catalytic activity in a certain extent. The effect of reaction condition was also studied. When the reaction was carded out under the following conditions： the reaction temperature 250℃, molar ratio of EC to DMT 3 ： 1, reaction time 3h, and catalyst amount 0.004 （molar ratio to DMT）, the yield of DMC was 68.9%.

Towards recycling purpose:Converting PET plastic waste back to terephthalic acid using pH-responsive phase transfer catalyst

Converting polyethylene terephthalate(PET)wastes to its monomer and valuable chemicals via ecofriendly chemical method is still a challenge task.Previously,phase transfer catalysts used for alkaline hydrolysis were soluble in reaction media and hardly separated after reaction.Here,we reported several pH-responsive catalysts combined alkyl quaternary ammonium units with heteropolyacid anion for achieving stepwise product/catalyst separation and catalyst recycling.The properties of homogeneous/heterogeneous transfer behavior allow catalyst to be easily separated from reaction media by adjusting of pH value.Among them,[C_(16)H_(33)N(CH_(3))_(3)]_(3)PW_(12)O_(40)(abbreviated as[CTA]_(3)PW)exhibits the highest activity and the most suitable pH responsive values.Such a pH triggered switchable catalytic system not only shows good performance for depolymerization of pure PET,but also some real PET wastes such as coloured trays and PE/PET complex films could be completely degraded into terephthalic acid.Additionally,the reaction kinetics and activation energy of PET alkaline hydrolysis also studied with and without pH-responsive[CTA]_(3)PW.

Transesterification of Ethylene Carbonate with Dimethyl Terephthalate over Various Metal Acetate Catalysts

The reaction between ethylene carbonate and dimethyl terephthalate was carried out for the simultaneous synthesis of dimethyl carbonate and poly（ethylene terephthalate）, This reaction is an excellent chemical process that is environmentally friendly and produces no poisonous substance. The metal acetate catalysts used for this reaction are discussed in detail. Lithium acetate dihydrate was found to be a novel and efficient catalyst for this reaction. Compared with other metal acetates, lithium acetate dihydrate can attain a maximum catalytic activity at a lower concentration. When the reaction was carried out under the following conditions： the reaction temperature from 230 to 250 ℃, molar ratio of ethylene carbonate（EC） to dimethyl terephthalate（DMT） 3： 1, reaction time 3 h, and a catalyst amount of 0. 4% （molar fraction to DMT）, the yield of dimethyl carbonate（DMC） was 79. 1%.

Tetra(acetylacetonato) tin(Ⅳ) as new catalyst for polytrimethylene terephthalate synthesis

Chelate tetra(acetylacetonato) tin(Ⅳ) was prepared and used as catalyst for polytrimethylene terephthalate synthesis.It exhibited higher catalytic activity than tetrabutyl titanate,butyltinhydroxide oxide and dibutyltin oxide.Decrease in reaction time, content of terminal carboxyl group,color intensity and increase in intrinsic viscosity were observed.The unique molecular structure can be considered as factor remarkably improving the catalytic activity of tetra(acetylacetonato) tin(Ⅳ).

Thermal Behavior of Poly(trimethylene-co-ethylene terephthalate)

Poly (trimethylene-co-ethylene terephthalate) with various compositions of diol has been synthesized. The crystallization of copolyesters with high comonomer content was observed by both wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC). It was found that the copolyesters become less crystallizable with the involvement of the comonomer, the crystals of crystallizable copolyesters come from PTT or PET homopolymers. The glass transition temperature (Tg) of the copolyester increases with increasing PET component in the copolyester, and the relationship between Tg and composition obey both Fox equation and additive law, the former is better in describing this relationship.

Alkylpolyglycoside inducing poly (butylene terephthalate) non-woven graft copolymerization of chitosan

In order to improve the wettability and biocompatibility of the poly （butylene terephthalate） non-woven （PBTNW）, the method of surface modification is used to graft copolymerization of chitosan （CS） onto the PBTNW under alkylpolyglycoside （APG） inducing. The product is thoroughly characterized with the Fourier transform infrared spectroscopy （FrIR）, the electron spectroscopy for chemical analysis （ESCA）, the thermogravimetric （TG） and the scanning electron microscopy （SEM）. It is found that chitosan is successfully grafted onto PBTNW. In addition, the water contact angles, hemolysis tests and cytotoxicity evaluation tests show an improvement in wettability and biocompatihility as a result of graft copolymerization of chitosan. So the CS-grafted PBTNW exhibits greater superiority than the original PBTNW. The CS-grafted PBTNW can be a candidate for blood filter materials and other medical applications.

Biodegradability of terephthalic acid in terylene artificial silk printing and dyeing wastewater

As the characteristic pollutant, terephthalic acid(TA)was in charge of 40%—78% of the total COD of terylene artificial silk printing and dyeing wastewater(TPW-water). The studies on biodegradability of TA were conducted in a serial of activated sludge reactors with TPW-water. TA appeared to be readily biodegradable with removal efficiency over 96.5% under aerobic conditions, hardly biodegradable with removal efficiency below 10% under anoxic conditions and slowly biodegradable with a turnover between 31.4% and 56.0% under anaerobic conditions. TA also accounted for the majority of BOD in TPW-water. The process combined by anoxic, anaerobic and aerobic activated sludge reactor was suitable for TA degradation and TPW-water treatment. Further, the aerobic process was essentially much more effective than the anaerobic or anoxic one to degrade TA in TPW-water.

Solid-Liquid Equilibrium of Terephthalic Acid in Several Solvents

Terephthalic acid(PTA) is practically one of the main materials of polyester. Its corresponding solid-liquid equilibrium data will provide essential support for industry design and further theoretical studies. In this work,solid-liquid equilibriums of terephthalic acid in four solvents, N,N-dimethylformamide, N,N-dimethylacetamide,dimethylsulphoxide and N-methyl-2-ketopyrrolidene, were determined in the temperature range from 293.15 K to 364.6 K by dynamic method. All these data were regressed by λh model, Wilson model and NRTL model, average absolute relative deviations of which are 1.25%, 15.02% and 7.22% respectively. It indicates that λh model is mostsuitable for description of the solid-liquid equilibrium containing PTA.

Surface Treatment of Polyethylene Terephthalate Film Using Atmospheric Pressure Glow Discharge in Air

Non-thermal plasmas under atmospheric pressure are of great interest in polymer surface processing because of their convenience, effectiveness and low cost. In this paper, the treatment of Polyethylene terephthalate (PET) film surface for improving hydrophilicity using the non-thermal plasma generated by atmospheric pressure glow discharge (APGD) in air is conducted. The discharge characteristics of APGD are shown by measurement of their electrical discharge parameters and observation of light-emission phenomena, and the surface properties of PET before and after the APGD treatment are studied using contact angle measurement, x-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It is found that the APGD is homogeneous and stable in the whole gas gap, which differs from the commonly filamentary dielectric barrier discharge (DBD). A short time (several seconds) APGD treatment can modify the surface characteristics of PET film markedly and uniformly. After 10 s APGD treatment, the

Dynamic Simulation and Analysis of Industrial Purified Terephthalic Acid Solvent Dehydration Process

Dynamic model for dehydration process of industrial purified terephthalic acid solvent is investigated to understand and characterize the process.A temperature differential expression is presented,which ensures the equation to convergence and short computation time.The model is used to study the dynamic behavior of an azeotropic distillation column separating acetic acid and water using n-butyl acetate as the entrainer.Responses of the column to feed flow and aqueous reflux flow are simulated.The movement of temperature front is also simulated.The comparison between simulation and industrial values shows that the model and algorithm are effective.On the basis of simulation and analysis,control strategy,online optimization and so on can be implemented effectively in dehydration process of purified terephthalic acid solvent.

Stannous-acetylacetonate:A new catalyst for poly(trimethylene terephthalate) synthesis

Stannous-acetylacetonate was prepared efficiently and characterized by ^1H NMR and FT-IR. Its catalytic activity for poly（trimethylene terephthalate） （PTT） synthesis was investigated. By this catalyst, the degree of esterification of pure terephthalic acid was up to 91.7% after reaction at 260 ℃ for 2 h, while the intrinsic viscosity and content of terminal carboxyl groups of the corresponding PTT polymerized at 260 ℃, 60 Pa for 2 h was 0.8816 dL/g and 17 mol/t,respectively. Stannous-acetylacetonate was more active and promising than tetrabutyl titanate and stannous octoate for PTT synthesis.

Multi-objective Optimization of Industrial Purified Terephthalic Acid Oxidation Process

Multi-objective optimization of a purified terephthalic acid (PTA) oxidation unit is carried out in this paper by using a process modei that has been proved to describe industrial process quite well. The modei is a semi-empirical structured into two series ideal continuously stirred tank reactor (CSTR) models. The optimal objectives include maximizing the yield or inlet rate and minimizing the concentration of 4-carboxy-benzaldhyde, which is the main undesirable intermediate product in the reaction process. The multi-objective optimization algorithra applied in this study is non-dominated sorting genetic algorithm Ⅱ (NSGA-Ⅱ). The performance of NSGA-Ⅱ is further illustrated by application to the title process.

Fuzzy Neural Network Model of 4-CBA Concentration for Industrial Purified Terephthalic Acid Oxidation Process

A fuzzy neural network (FNN) model is developed to predict the 4-CBA concentration of the oxidation unit in purified terephthalic acid process. Several technologies are used to deal with the process data before modeling.First,a set of preliminary input variables is selected according to prior knowledge and experience. Secondly,a method based on the maximum correlation coefficient is proposed to detect the dead time between the process variables and response variables. Finally, the fuzzy curve method is used to reduce the unimportant input variables.The simulation results based on industrial data show that the relative error range of the FNN model is narrower than that of the American Oil Company (AMOCO) model. Furthermore, the FNN model can predict the trend of the 4-CBA concentration more accurately.

Stannous oxalate as a novel catalyst for the synthesis of polytrimethylene terephthalate

Stannous oxalate was prepared efficiently and characterized by XRD and FT-IR. It exhibited higher catalytic activity and had profitable effect than tetrabutyl titanate and stannous octoate for the synthesis of polytrimethylene terephthalate （PTT） via esterification-route. Over this catalyst, the degree of esterification of pure terephthalic acid was up to 94.4% at 260 ℃ after 1.5 h,while the intrinsic viscosity and content of terminal carboxyl groups of the corresponding PTT polyester, polymerized at 260 ℃,60 Pa for 2 h, was 0.8950 dL/g and 15 mol/t, respectively. Stannous oxalate was a promising catalyst for the synthesis of PTT polyester.