A Novel Variable Shifting Code for Test Compression of SoC

The test vector compression is a key technique to reduce IC test time and cost since the explosion of the test data of system on chip （SoC） in recent years. To reduce the bandwidth requirement between the automatic test equipment （ATE） and the CUT （circuit under test） effectively, a novel VSPTIDR （variable shifting prefix-tail identifier reverse） code for test stimulus data compression is designed. The encoding scheme is defined and analyzed in detail, and the decoder is presented and discussed. While the probability of 0 bits in the test set is greater than 0.92, the compression ratio from VSPTIDR code is better than the frequency-directed run-length （FDR） code, which can be proved by theoretical analysis and experiments. And the on-chip area overhead of VSPTIDR decoder is about 15.75 % less than the FDR decoder.

Determination of Material Parameters of EVA Foam under Uniaxial Compressive Testing Using Hyperelastic Models

The objective of this research was to determine the mechanical parameter from EVA foam and also investigate its behavior by using Blatz-Ko,Neo-Hookean,Mooney model and experimental test.The physical characteristic of EVA foam was also evaluated by scanning electron microscopy(SEM).The results show that Blatz-Ko and Neo-Hookean model can fit the curve at 5%and 8%strain,respectively.The Mooney model can fit the curve at 50%strain.The modulus of rigidity evaluated from Mooney model is 0.0814±0.0027 MPa.The structure of EVA foam from SEM image shows that EVA structure is a closed cell with homogeneous porous structure.From the result,it is found that Mooney model can adjust the data better than other models.This model can be applied for mechanical response prediction of EVA foam and also for reference value in engineering application.

Constitutive relationship of IN690 superalloy by using uniaxial compression tests

The hot deformation behavior of IN690 superalloy was characterized in a temperature range of 1273-1473 K and a strain rate range of 0.01-10 s^-1 using uniaxial compression tests on process annealed material.The constitutive relations between flow stress and effective strain,effective strain rate as well as deformation temperature were studied.It can be concluded that the flow stress significantly reduces with the deformation temperature of IN690 superalloy increasing.Whereas,there is a significant increase of flow stress when the strain rate increases from 0.1 s^-1 to 10 s^-1.Based on the hyperbolic-sine Arrhenius-type equation,a constitutive equation considering compensation of strain was developed.The activation energy and the material constants（Q,n and ln A） decrease as the deformation strain increases.The strain dependent term is successfully incorporated in the constitutive equation through a quartic equation.A good agreement between the experimental data and the predicted results has been achieved,indicating that the proposed constitutive equation and the methods of determing the material constants are suitable to model the high temperature deformation behavior of IN690 superalloy.

Temperature-controlled triaxial compression/creep test device for thermodynamic properties of soft sedimentary rock and corresponding theoretical prediction

In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of the waste.In this paper,some experimental researches on the thermo-mechanical characteristics of soft sedimentary rock have been presented.For this reason,a new temperature-controlled triaxial compression and creep test device,operated automatically by a computer-controlled system,whose control software has been developed by the authors,was developed to conduct the thermo-mechanical tests in different thermal loading paths,including an isothermal path.The new device is proved to be able to conduct typical thermo-mechanical element tests for soft rock.The test device and the related testing method were introduced in detail.Finally,some test results have been simulated with a thermo-elasto-viscoplastic model that was also developed by the authors.

System-on-Chip Test Data Compression Based on Split-Data Variable Length (SDV) Code

System-on-a-chips with intellectual property cores need a large volume of data for testing. The large volume of test data requires a large testing time and test data memory. Therefore new techniques are needed to optimize the test data volume, decrease the testing time, and conquer the ATE memory limitation for SOC designs. This paper presents a new compression method of testing for intellectual property core-based system-on-chip. The proposed method is based on new split- data variable length (SDV) codes that are designed using the split-options along with identification bits in a string of test data. This paper analyses the reduction of test data volume, testing time, run time, size of memory required in ATE and improvement of compression ratio. Experimental results for ISCAS 85 and ISCAS 89 Benchmark circuits show that SDV codes outperform other compression methods with the best compression ratio for test data compression. The decompression architecture for SDV codes is also presented for decoding the implementations of compressed bits. The proposed scheme shows that SDV codes are accessible to any of the variations in the input test data stream.

Three-dimensional finite element simulation and reconstruction of jointed rock models using CT scanning and photogrammetry

The geometry of joints has a significant influence on the mechanical properties of rocks.To simplify the curved joint shapes in rocks,the joint shape is usually treated as straight lines or planes in most laboratory experiments and numerical simulations.In this study,the computerized tomography (CT) scanning and photogrammetry were employed to obtain the internal and surface joint structures of a limestone sample,respectively.To describe the joint geometry,the edge detection algorithms and a three-dimensional (3D) matrix mapping method were applied to reconstruct CT-based and photogrammetry-based jointed rock models.For comparison tests,the numerical uniaxial compression tests were conducted on an intact rock sample and a sample with a joint simplified to a plane using the parallel computing method.The results indicate that the mechanical characteristics and failure process of jointed rocks are significantly affected by the geometry of joints.The presence of joints reduces the uniaxial compressive strength (UCS),elastic modulus,and released acoustic emission (AE) energy of rocks by 37%–67%,21%–24%,and 52%–90%,respectively.Compared to the simplified joint sample,the proposed photogrammetry-based numerical model makes the most of the limited geometry information of joints.The UCS,accumulative released AE energy,and elastic modulus of the photogrammetry-based sample were found to be very close to those of the CT-based sample.The UCS value of the simplified joint sample (i.e.38.5 MPa) is much lower than that of the CT-based sample (i.e.72.3 MPa).Additionally,the accumulative released AE energy observed in the simplified joint sample is 3.899 times lower than that observed in the CT-based sample.CT scanning provides a reliable means to visualize the joints in rocks,which can be used to verify the reliability of photogrammetry techniques.The application of the photogrammetry-based sample enables detailed analysis for estimating the mechanical properties of jointed rocks.

Fundamental Study on Response Properties of Structures Constructed on Lunar Regolith

The Artemis Program, for constructing the lunar base, is in progress. How to design and construct architectural and civil engineering structures in the lunar environment has become an important issue. The lunar surface is covered with soft sand, called regolith, and it is required to protect lunar bases and structures, as well as internal precision equipment, against vibrational disturbances such as moonquakes and meteorite collisions. Therefore, in this study, the static and cyclic triaxial compression tests of the regolith simulant were conducted. The reference strain and equivalent damping factor of the regolith simulant were smaller compared to sandy soil on Earth. In addition, a shaking table test using model specimens was conducted on the response properties of regolith ground alone and structures set on regolith ground. The buried foundation and pile foundation notably suppressed the horizontal response attributed to the rocking component compared to a direct foundation.

Particle simulation of the failure process of brittle rock under triaxial compression

In order to investigate the failure process of brittle rock under triaxial compression through both experimental and numerical approaches, the particle simulation method was used in numerical simulations and the simulated results were compared with those of the experiment. The numerical simulation results, such as fracture propagation, microcrack distribution, stress-strain response, and damage patterns, were discussed in detail. The simulated results under various confining pressures （0-60 MPa） are in good agreement with the experimental results. The simulated results reveal that rock failure is caused by axial splitting under uniaxial compression. As the confining pressure increases, rock failure occurs in a few localized shear planes and the rock mechanical behavior is changed from brittle to ductile. Consequently, the peak failure strength, microcrack numbers, and the shear plane angle increase, but the ratio of tensile to shear microcracks decreases. The damage formation during the compression simulations indicates that the particle simulation method can produce similar behaviors as those observed through laboratory compression tests.

Experimental study on cracking behaviour of moulded gypsum containing two non-parallel overlapping flaws under uniaxial compression

Failure of rock mass that is subjected to compressive loads occurs from initiation, propagation, and linkage of new cracks from preexisting fissures. Our research investigates the cracking behaviour and coalescence process in a brittle material with two non-parallel overlapping flaws using a high-speed camera. The coalescence tensile crack and tensile wing cracks were the first cracks to occur from the preexisting flaws. The initiation stresses of the primary cracks at the two tips of each flaw were simultaneous and decreased with reduced flaw inclination angle. The following types of coalescence cracks were identified between the flaws: primary tensile coalescence crack, tensile crack linkage, shear crack linkage, mixed tensile-shear crack, and indirect crack coalescence. Coalescence through tensile linkage occurred mostly at pre-peak stress. In contrast, coalescence through shear or mixed tensile-shear cracks occurred at higher stress. Overall, this study indicates that the geometry of preexisting flaws affect crack initiation and coalescence behaviour.

Specimen aspect ratio and progressive field strain development of sandstone under uniaxial compression by three-dimensional digital image correlation

The complete stress-strain characteristics of sandstone specimens were investigated in a series of quasistatic monotonic uniaxial compression tests.Strain patterns development during pre-and post-peak behaviours in specimens with different aspect ratios was also examined.Peak stress,post-peak portion of stress-strain,brittleness,characteristics of progressive localisation and field strain patterns development were affected at different extents by specimen aspect ratio.Strain patterns of the rocks were obtained by applying three-dimensional(3D) digital image correlation(DIC) technique.Unlike conventional strain measurement using strain gauges attached to specimen,3D DIC allowed not only measuring large strains,but more importantly,mapping the development of field strain throughout the compression test,i.e.in pre-and post-peak regimes.Field strain development in the surface of rock specimen suggests that strain starts localising progressively and develops at a lower rate in pre-peak regime.However,in post-peak regime,strains increase at different rates as local deformations take place at different extents in the vicinity and outside the localised zone.The extent of localised strains together with the rate of strain localisation is associated with the increase in rate of strength degradation.Strain localisation and local inelastic unloading outside the localised zone both feature post-peak regime.

Shape ratio effects on the mechanical characteristics of rectangular prism rocks and isolated pillars under uniaxial compression

Isolated pillars in underground mines are subjected to uniaxial stress,and the load bearing cross-section of pillars is commonly rectangularly shaped.In addition,the uniaxial compression test(UCT)is widely used for determining the basic mechanical properties of rocks and revealing the mechanism of isolated pillar disasters under unidimensional stress.The shape effects of rock mechanical properties under uniaxial compression are mainly quantitatively reflected in the specific shape ratios of rocks.Therefore,it is necessary to study the detailed shape ratio effects on the mechanical properties of rectangular prism rock specimens and isolated pillars under uniaxial compressive stress.In this study,granite,marble and sandstone rectangular prism specimens with various height to width ratios(r)and width to thickness ratios(u)were prepared and tested.The study results show that r and u have a great influence on the bearing ability of rocks,and thin or high rocks have lower uniaxial compressive strength.Reducing the level of r can enhance the u effect on the strength of rocks,and increasing the level of u can enhance the r effect on the strength of rocks.The lateral strain on the thickness side of the rock specimen is larger than that on the width side,which implies that crack growth occurs easily on the thickness side.Considering r and u,a novel strength prediction model of isolated pillars was proposed based on the testing results,and the prediction model was used for the safety assessment of 179 isolated pillars in the Xianglu Mountain Tungsten Mine.

Analysis of the stress ratio of anisotropic rocks in uniaxial tests

The effect of structural discontinuities on the progressive failure process of anisotropic rocks should be paid particular attention.The crack damage stress σ_(cd),also considered as the yield strength,and the relationship between σ_(cd) and the uniaxial peak strength σ_(ucs) of anisotropic rocks for different orientations 8 of the isotropy planes with respect to the loading directions were investigated theoretically and experimentally.A theoretical relation of σ_(cd)/σ_(ucs) with the function of the shape parameter m was established.Additionally,uniaxial compression tests of shale samples were conducted for several inclinations θ.The test result of σ_(cd)/σ_(ucs) was close to the theoretical value for a given orientation.Furthermore,both experimental results and theoretical solutions of σ_(cd)/σ_(ucs) were independent of the inclination θ while σ_(cd) andσ_(ucs) were strongly affected by θ.The strength ratio σ_(cd)/σ_(ucs) may therefore be an intrinsic property of anisotropic rocks and could be used to predict the failure of rock samples.

EFFECTS OF STRAIN RATE ＆TEMPERATURE ON HOT COMPRESSION FLOW BEHAVIOR OF A HYDROGENATED CAST Ti－25Al－

The flow behavior of a cast Ti-25Al-10Nb-3V-1Mo alloy based onTi3Al, with and without hydrogen content, was investigated under isothermal compression test at strain rates of 0.1s-1 to 0.001s -1 in the temperature range of 900℃ to1000 ℃. The hot compression peak stress (or the maximum flow stress) of the alloy withand without hydrogen decreases with the increasing temperature and the decreasingstrain rate. Hydrogenation makes the hot compression peak stress decrease by 37%～53%, which corresponds to lowering the deformation temperature by about 50℃.Strain rate does not change the favorable effect of hydrogenation on hot compressionflow behavior at all three deformation temperatures. The microstructure of the alloywith 0.2% H (mass %) deformed at a fixed temperature exhibits the same feature asthat of the alloys without hydrogenation deformed at higher temperatures for bothstrain rates. Hydrogenation has the same effect on microstructure as strain rate andtemperature.

Validity of continuous-failure-state unloading triaxial tests as a means to estimate the residual strength of rocks

The residual strength of rocks and rock masses is an important parameter to be constrained for analysis and design purposes in many rock engineering applications.A residual strength envelope in principal stress space is typically developed using residual strength data obtained from compression tests on many different specimens of the same rock type.In this study,we examined the potential for use of the continuous-failure-state testing concept as a means to constrain the residual strength envelope using a limited number of specimens.Specifically,cylindrical specimens of three rock types(granodiorite,diabase,and Stanstead granite)were unloaded at the residual state such that a full residual strength envelope for each individual specimen was obtained.Using a residual strength model that introduces a single new strength parameter(the residual strength index,or RSI),the results of the continuous-failurestate unloading tests were compared to conventionally obtained residual strength envelopes.Overall,the continuous-failure-state residual strength data were found to be consistent with the conventional residual strength data.However,it was identified that the primary factor limiting an accurate characterization of the residual strength for a given rock type is not the amount of data for a given specimen,but the variety of specimens available to characterize the inherent variability of the rock unit of interest.Accordingly,the use of continuous-failure-state testing for estimation of the residual strength of a rock unit is only recommended when the number of specimens available for testing is very limited(i.e.<5).

The Application of Dynamic Shock Mechanics Test in Engineering Blasting

With the continuous advancement of China’s infrastructure construction to the west,according to the geographic situation in the southwest region,such as mountainous areas and complex terrain,the road construction process is inevitably accompanied by earth and rock blasting.To improve the quality and safety of the project,this paper addresses the problems of land and rock blasting faced in the construction of mountain road projects,taking the research of rock dynamic mechanics test as the starting point,and using a combination of theoretical analysis and experimental research methods.The specific research content includes the following parts:dynamic impact compression test(SHPB),dynamic splitting tensile test,and stress-strain curve analysis of the test results,which provides the theoretical basis and numerical parameters for the numerical simulation of future engineering blasting.

Transmission ratio (T_n) in the radian direction normal to joints in 2-D compressional wave propagation in rock masses

The transmission ratio along the radian direction normal to the joints was studied in the Universal Distinct Element Code （UDEC）. The variation of the transmission ratio with the ratio of joint spacing to wavelength was generalized into a general curve, which was determined by two critical points. The relationship between the two critical points and the affecting factors, quantity of joints and the normalized normal stiffness of joints, were obtained. A prediction model of the transmission ratio in the radian direction normal to the joints was proposed. The proposed model was applied to a field explosion test. The estimated values of the peak particle velocity from the prediction model were compared with the field records. The comparisons showed that the prediction model of the transmission ratio in the direction normal to the joints in the process of 2-D compressional wave propagation through multiple parallel joints is reliable.

Effect of gravel on rock failure in glutenite reservoirs under different confining pressures

Due to the existence of gravel,glutenite is heterogeneous and different from fine-grained rocks such as sandstone and shale in structure.To fully understand the effect of gravel on failure mode in glutenite,we performed triaxial compression tests on different glutenites.The results indicate that failure modes of glutenite are complex due to the existence of gravel.Under different confining pressures,three failure modes were observed.The first failure mode,a tensile failure under uniaxial compression,produces multiple tortuous longitudinal cracks.In this failure mode,the interaction between gravels provides the lateral tensile stress for rock splitting.The second failure mode occurs under low and medium confining pressure and produces a crack band composed of micro-cracks around gravels.This failure mode conforms to the Mohr-Coulomb criterion and is generated by shear failure.In this failure mode,shear dilatancy and shear compaction may occur under different confining pressures to produce different crack band types.In the second failure mode,gravel-induced stress concentration produces masses of initial micro-cracks for shear cracking,and gravels deflect the fracture surfaces.As a result,the fracture is characterized by crack bands that are far broader than in fine-grained rocks.The third failure mode requires high confining pressure and produces disconnected cracks around gravels without apparent crack bands.In this failure mode,the gravel rarely breaks,indicating that the formation of these fractures is related to the deformation of the matrix.The third failure mode requires lower confining pressure in glutenite with weak cement and matrix support.Generally,unlike fine-grained rocks,the failure mode of glutenite is not only controlled by confining pressure but also by the gravel.The failure of glutenite is characterized by producing cracks around gravels.These cracks are produced by different mechanisms and distributed in different manners under different confining pressures to form different fracture patterns.Therefore,understanding the rock microstructure and formation stress state is essential in guiding glutenite reservoir development.

Effects of confining pressure and temperature on strength and deformation behavior of frozen saline silty clay

Buildings are always affected by frost heave and thaw settlement in cold regions,even where saline soil is present.This paper describes the triaxial testing results of frozen silty clay with high salt content and examines the in-fluence of confining pressure and temperature on its mechanical characteristics.Conventional triaxial compression tests were conducted under different confining pressures(0.5–7.0 MPa)and temperatures(-6℃,-8℃,-10℃,and-12℃).The test results show that when the confining pressure is less than 1 MPa,the frozen saline silty clay is dominated by brittle behavior with the X-shaped dilatancy failure mode.As the confining pressure increases,the sample gradually transitions from brittle to plastic behavior.The strength of frozen saline silty clay rises first and then decreases with increasing confining pressure.The improved Duncan-Chang hyperbolic model can describe the stress-strain relationship of frozen saline silty clay.And the parabolic strength criterion can be used to describe the strength evolution of frozen saline silty clay.The function relation of strength parameters with temperature is obtained by fitting,and the results of the parabolic strength criterion are in good agreement with the experimental results,especially when confining pressure is less than 5 MPa.Therefore,the study has important guiding significance for design and construction when considering high salinity soil as an engineering material in cold regions.

Assessment of inherent heterogeneity effect on continuous mechanical properties of shale via uniaxial compression and scratch test methods

Shale reservoirs have been a significant focus of hydrocarbon production over the past few decades,and the mechanical assessment of target shale reservoirs has been critical to successful field operations,especially in hydraulic fracturing and well completions.The Unconfined compressive strength(UCS)and Poisson's ratio(ν)are critical mechanical properties in shale reservoir assessment.The estimation and measurement of shale mechanical properties are often erroneous by not accounting for their heterogeneous and pre-existing features,which yield variability of shale mechanical properties along their lithostratigraphy.Thus,there is a need to investigate the degree of correlation and accuracy in multiscale mechanical evaluations of heterogeneous shales,and the correlation between such micromechanical and macromechanical measurements.This study investigated the impact of inherent heterogeneity on the measurement of continuous micromechanical and macromechanical properties of shale reservoirs using scratch test(ST)and uniaxial compression test(UCT)methods,and the degree of correlation(correlation coefficient,r)of measurements in shale was further assessed for the variability of their measured properties.Shale core samples from three distinct shale formations were utilized and studied,and the core samples were subjected to ST and UCT,respectively.The results from this study showed that despite inherent heterogeneous anomalies and natural fractures in the shale samples analyzed,there is a good degree of correlation(UCS:r=0.73;ν:r=0.89)in the micro-and macro-mechanical properties of shales using two independent experimental tests(ST and UCT).This study provides insights for improving the accuracy of mechanical evaluations and numerical modeling in shales with a high degree of heterogeneity and pre-existing natural fractures.The results indicate that when considering the structural complexity and heterogeneity of unconventional reservoirs such as shales,the ST method can provide a better continuous micromechanical assessment of shales.In contrast,the UCT can provide a better bulk macromechanical measurement of shales.

用压缩蠕变试验研究高填方体沉降变形

以九寨 黄龙机场104m高填方体为工程背景,研究了砂砾石填料压缩蠕变试验与高填方体的相似条件.研究表明,刚性侧限的压缩蠕变试验与大面积凹谷中的高填方体具较好的相似性,两者可近似为等应力状态,但试验得出的高填方体压缩沉降量较实测值稍小.此外,初始压实度决定了砂砾石填料的压缩变形特性,初始压实度为97.4%的砂砾石填料的压缩变形过程具对数函数特征,而初始压实度大于98.7%的砂砾石填料的压缩变形过程则以线性函数特征为主.