Influence of reaction piles on test pile response in a static load test

This work presents a new analytical method to analyze the influence of reaction piles on the test pile response in a static load test.In our method,the interactive effect between soil and pile is simulated using independent springs and the shear displacement method is adopted to analyze the influence of reaction piles on test pile response.Moreover,the influence of the sheltering effect between reaction piles and test pile on the test pile response is taken into account.Two cases are analyzed to verify the rationality and efficiency of the present method.This method can be easily extended to a nonlinear response of an influenced test pile embedded in a multilayered soil,and the validity is also demonstrated using centrifuge model tests and a computer program presented in the literature.The present analyses indicate that the proposed method will lead to an underestimation of the test pile settlement in a static load test if the influence of the presence of reaction piles on the test pile response is neglected.

Model tests on XCC-piled embankment under dynamic train load of high-speed railways

Piled embankments,which offer many advantages,are increasingly popular in construction of high-speed railways in China.Although the performance of piled embankment under static loading is well-known,the behavior under the dynamic train load of a high-speed railway is not yet understood.In light of this,a heavily instrumented piled embankment model was set up,and a model test was carried out,in which a servo-hydraulic actuator outputting M-shaped waves was adopted to simulate the process of a running train.Earth pressure,settlement,strain in the geogrid and pile and excess pore water pressure were measured.The results show that the soil arching height under the dynamic train load of a high-speed railway is shorter than under static loading.The growth trend for accumulated settlement slowed down after long-term vibration although there was still a tendency for it to increase.Accumulated geogrid strain has an increasing tendency after long-term vibration.The closer the embankment edge,the greater the geogrid strain over the subsoil.Strains in the pile were smaller under dynamic train loads,and their distribution was different from that under static loading.At the same elevation,excess pore water pressure under the track slab was greater than that under the embankment shoulder.

Shaking Table Tests on Bridge Foundation Reinforced by Antislide Piles on Slope

Based on the requirement of seismic reinforcement of bridge foundation on slope in the Chengdu-Lanzhou railway project,a shaking table model test of anti-slide pile protecting bridge foundation in landslide section is designed and completed. By applying Wenchuan seismic waves with different acceleration peaks,the stress and deformation characteristics of bridge pile foundation and anti-slide pile are analyzed,and the failure mode is discussed. Results show that the dynamic response of bridge pile and anti-slide pile are affected by the peak value of seismic acceleration of earthquake,with which the stress and deformation of the structure increase. The maximum dynamic earth pressure and the moment of anti-slide piles are located near the sliding surface,while that of bridge piles are located at the top of the pile. Based on the dynamic response of structure,local reinforcement needs to be carried out to meet the requirement of the seismic design. The PGA amplification factor of the surface is greater than the inside,and it decreases with the increase of the input seismic acceleration peak. When the slope failure occurs,the tension cracks are mainly produced in the shallow sliding zone and the coarse particles at the foot of the slope are accumulated.

Uplift Pile Test in Rocks and Its Bearing Capacity

This paper reports in situ tension test and laboratory model test for large diameter, manually digging anchorage piles in the 2nd Luzhou Changjiang Bridge. Tension behavior, uplift bearing capacity and influence of rock characteristics on bearing capacity are discussed. Proposes are presented with respect to issues related to the construction and design of uplift piles.

Model Tests of Pile Defect Detection

The pile, as an important foundation style, is being used in engineering practice. Defects of different types and damages of different degrees easily occur during the process of pile construction. So, dietecting defects of the pile is very important. As so far, there are some difficult problems in pile defect detection. Based on stress wave theory, some of these typical difficult problems were studied through model tests. The analyses of the test results are carried out and some significant results of the low-strain method are obtained, when a pile has a gradually-decreasing crosssection part, the amplitude of the reflective signal originating from the defect is dependent on the decreasing value of the rate of crosssection β. No apparent signal reflected from the necking appeares on the velocity response curve when the value of β is less than about 3. 5 %.

Simulation analysis for O-cell test of pile and the interaction of upper pile and lower pile

In this paper,the soil-pile system of O-cell test of pile is simplified as an axi-symmetric problem.By using aggregation of quadrilateral isoparametric elements to simulate pile and soil,setting Goodman's elements between pile and soils,a method of numerical simulation analysis on O-cell test of pile is presented with the consideration of nonlinear mechanical behavior of soils and pile-soil interface.The method is applied to the analysis of a case of O-cell test of pile.The load-displacement curves and axial force curves of upper pile and lower pile obtained from the O-cell test of pile are fitted,and parameters of the mechanical model of soils and interface are determined.Analysis results validate that the numerical simulation analysis method put forward in this paper is applicable.Furthermore,the interaction and influence of upper pile and lower pile in the O-cell test are also studied with the method.The result shows that if load box is located in a soil layer with fine mechanical behavior,the interaction of upper pile and lower pile in O-cell test can be ignored generally.

Regressive approach for predicting bearing capacity of bored piles from cone penetration test data

In this study, th e least sq u are su p p o rt v ecto r m achine （LSSVM） alg o rith m w as applied to predicting th ebearing capacity o f b ored piles e m b ed d ed in sand an d m ixed soils. Pile g eo m etry an d cone p e n e tra tio nte s t （CPT） resu lts w ere used as in p u t variables for pred ictio n o f pile bearin g capacity. The d ata u se d w erecollected from th e existing litera tu re an d consisted o f 50 case records. The application o f LSSVM w ascarried o u t by dividing th e d ata into th re e se ts： a train in g se t for learning th e pro b lem an d obtain in g arelationship b e tw e e n in p u t variables an d pile bearin g capacity, and testin g an d validation sets forevaluation o f th e predictive an d g en eralization ability o f th e o b tain ed relationship. The predictions o f pilebearing capacity by LSSVM w ere evaluated by com paring w ith ex p erim en tal d ata an d w ith th o se bytrad itio n al CPT-based m eth o d s and th e gene ex pression pro g ram m in g （GEP） m odel. It w as found th a t th eLSSVM perform s w ell w ith coefficient o f d eterm in atio n , m ean, an d sta n d ard dev iatio n equivalent to 0.99,1.03, an d 0.08, respectively, for th e testin g set, an d 1, 1.04, an d 0.11, respectively, for th e v alidation set. Thelow values o f th e calculated m ean squared e rro r an d m ean ab so lu te e rro r indicated th a t th e LSSVM w asaccurate in p redicting th e pile bearing capacity. The results o f com parison also show ed th a t th e p roposedalg o rith m p red icted th e pile bearin g capacity m ore accurately th a n th e trad itio n al m eth o d s including th eGEP m odel.

Shake table test of soil-pile groups-bridge structure interaction in liquefiable ground

This paper describes a shake table test study on the seismic response of low-cap pile groups and a bridge structure in liquefiable ground. The soil profile, contained in a large-scale laminar shear box, consisted of a horizontally saturated sand layer overlaid with a silty clay layer, with the simulated low-cap pile groups embedded. The container was excited in three E1 Centro earthquake events of different levels. Test results indicate that excessive pore pressure （EPP） during slight shaking only slightly accumulated, and the accumulation mainly occurred during strong shaking. The EPP was gradually enhanced as the amplitude and duration of the input acceleration increased. The acceleration response of the sand was remarkably influenced by soil liquefaction. As soil liquefaction occurred, the peak sand displacement gradually lagged behind the input acceleration; meanwhile, the sand displacement exhibited an increasing effect on the bending moment of the pile, and acceleration responses of the pile and the sand layer gradually changed from decreasing to increasing in the vertical direction from the bottom to the top. A jump variation of the bending moment on the pile was observed near the soil interface in all three input earthquake events. It is thought that the shake table tests could provide the groundwork for further seismic performance studies of low-cap pile groups used in bridges located on liquefiable groun.

Field load testing of copper extraction aeration pipes under simulated high heap pile

Recently a research team at Ohio University,USA,conducted a unique full-scale feld load test to simulate the aeration pipe installations at a copper extraction mine operated in Chile.The overliner material taken from the mine was used in recreating the in situ conditions.Electric heaters were utilized to raise the temperature inside each pipe to simulate the essential element of the copper extraction process.The maximum vertical deflection reached by the test pipes was close to 20%,when the simulated heap pile height was 80 m.The plastic pipes and the overliner material were also tested in the laboratory.Based on the results,the maximum heap pile fll depth was recommended for the aeration system.The results indicated that the vertical deflection was the primary performance index for the aeration pipes installed in heap piles at mines.Lastly,the pipe made of polypropylene resin was super.

The Shaking Table Test on the Performance of Cement-mixed Piles in Liquefiable Railway Foundations

Cement-mixed piles,as countermeasure against liquefaction of silt and sand ground,can improve the shear strength and bearing capacity of foundation soil,meaning cement-mixed piles are capable of resisting displacement when an earthquake happens. However,investigations of cement-mixed piles by experimental methods such as the shaking table test is few and far between. It is especially true for the seismic performance of cement-mixed piles in liquefiable railway foundations in high seismic intensity regions. To this end,a cross-section of the Yuxi-Mengzi railway was selected as the prototype and studied by the shaking table test in this study. The results showed that composite foundation of cementmixed piles was not liquefied when the seismic acceleration was lower than 0. 30g. In the process of acceleration increasing from 0. 30g at 2Hz to 0. 60g at 3Hz,the upper middle silt outside slope toe was partly liquefied. The foundation soil under the shoulders and center of subgrade was far from the initial liquefaction criterion during the test. Cementmixed piles can effectively reduce the embankment settlement and differential settlement. It can be concluded that, the design of cement-mixed piles can ensure the seismic performance of the subgrade,and satisfy the seismic design requirements of the YuxiMengzi railway in areas of VIII degrees seismic fortification intensity.

In-Situ Test on Fatigue Characteristics of Top-Mounted Dividable Pile-Board Subgrade for High-Speed Railway

To simulate the fatigue characteristics of the pile-board structure under long-term dynamic load, using the in-situ dynamic testing system DTS-1, the forced vibration loading was repeated one million times at different cross-sections of the pile-board structure for high-speed railway. The dynamic deformation, permanent deformation and dynamic stress of main reinforcements were measured. The test results show that the dynamic responses of the pile-board structure almost did not vary with the forced vibration times under the simulated trainload. After one million times of forced vibration, the permanent deformations of the midspan section of intermediate span and midspan section of side span were 0.7 mm and 0. 6 mm, respectively, and there was no accumulative plastic deformation at the bearing section of intermediate span.

Static load test and load transfer mechanism study of squeezed branch and plate pile in collapsible loess foundation

As a special geological phenomenon, the character of collapsible loess foundation is collapsible when penetrated by water. This character leads to the soil losing load bearing capacity largely and may lead to foundation failure. Pile is a popular foundation used in collapsible loess. The squeezed branch and plate pile is a new type of pile developed in recent years and has not be used in a project before. In this paper three squeezed branch and plate piles are tested in collapsible loess after immersion processing. The results may be used for reference in similar construction project, and to provide theoretical references for de- signing of the squeezed branch and plate piles in engineering practice.

粗糙度对单桩竖向承载变形特性影响的试验研究

为探究桩侧粗糙度对单桩承载变形特性的影响规律,自主研发了多功能桩基静动力模型试验系统,构建了光滑、随机型及带肋规则型桩侧界面的模型单桩,通过3D形态扫描计算获得了桩侧表面粗糙度Rn,基于此开展了饱和砂土中单桩静载模型试验。试验结果表明:(1)粗糙度越大,单桩极限承载力和桩的割线刚度越大,桩顶沉降及其卸载回弹量越小,带肋桩能够有效提高桩基承载力并控制桩顶变形。(2)粗糙度越大,桩侧阻力越大,桩端附近侧阻力的强化效应越明显,桩侧阻力的分布模式随桩顶荷载增大由“单驼峰”到“锥顶柱”再至“斜坡”依次演变。(3)β值(β法中参数)随桩侧粗糙度的增大而增加,随深度增加而衰减。带肋桩的极限侧阻力及β值远大于砂纸和光滑桩,揭示了埋深和粗糙度对β值影响规律的机制。(4)桩侧粗糙度会影响砂土地基中桩端荷载传递函数类型,光滑桩、砂纸桩桩端荷载传递函数呈双曲线型,带肋桩呈直线型。上述研究结果对深刻认识桩侧粗糙度对单桩承载变形特性影响规律和机制具有重要参考价值。

砂土中能量桩单桩水平承载特性模型试验研究

为探究能量桩单桩水平承载特性,针对砂土中能量桩在水平荷载下的承载特性进行研究,基于模型试验,分析了水平荷载作用下能量桩在制冷和加热过程中的桩顶位移、桩前土压力以及桩身弯矩等的变化规律。研究结果表明:制冷会引起能量桩桩顶水平位移略微增大,增量为0.48%D(D为桩体直径),而加热会引起较大的桩顶水平位移,达到了2.38%D;制冷和加热在初始阶段会引起桩前土压力增大,初始增长阶段结束后,土压力变化较小,多为缓慢增长或基本不变。相较于初始土压力,制冷和加热结束时的土压力基本呈增长趋势,仅个别埋深处土压力减小。制冷过程中,埋深0%L~40%L(L为有效桩长)范围内的弯矩增大,埋深40%L~100%L位置处的弯矩变化较小;加热过程中,埋深0%L~60%L范围内的弯矩均有所增大,0%L~40%L位置处的弯矩增大最为明显。制冷和加热过程中均在20%L处产生了最大弯矩,最大弯矩的增加量分别为9.93%和10.32%。进一步基于圆孔扩张理论提出了弯矩计算的理论解,并与试验结果进行对比分析,理论计算值与实测值较为吻合。

微型木桩的群桩效应研究

木材广泛存在于我国村镇中,其取材加工方便,价格低廉,用作村镇住宅的基础结构,可有效减少村镇住宅的能源消耗,符合绿色建筑理念。本文以微型木桩为研究对象,通过离心机模型试验和有限元数值分析,研究了微型木桩在砂土和粉质黏土土层条件下的群桩承载力和群桩效应系数。结果表明,微型木桩的群桩效应系数η在砂土中大于1,在黏土中小于1,受桩土刚度比的影响较小;桩径减小改变了群桩最优桩间距,砂土中微型木桩η随着桩的距径比Sa/D的增大逐渐增大,在Sa/D=6时出现峰值,常规桩在Sa/D=3时达到最大,微型木桩最优桩间距大于常规桩;黏土中,微型木桩η峰值对应的Sa/D=4小于常规桩η峰值对应的Sa/D=6,微型木桩最优桩间距小于常规桩;微型木桩群桩效应系数随内摩擦角和不排水抗剪强度的增大而减小,随距径比的增大先增加后减小,随桩数的增加而增大。

黄土地基中能量桩群桩承载变形性状模型试验

基于室内缩尺试验研究了含能量桩群桩在4次冷热循环过程中的桩身热力学特性及桩基承载变形特性变化规律,分析冷热循环对桩土温度、承台沉降、桩顶荷载及桩身摩阻力的影响。试验结果表明:冷热循环过程中能量桩较浅位置处桩身及桩侧土温度始终高于较深处,热循环过程中能量桩的传热效率高于冷循环过程。冷热循环会使承台顶面的工作荷载及群桩中各基桩的桩顶荷载发生往复变化,相应地引起承台发生往复倾斜,热循环引起的承台倾斜稍大于冷循环。热循环引起的能量桩桩身上部摩阻力为负,下部为正,冷循环时则相反。

洞桩法地铁车站边桩结构受力机制的模型试验设计

为了方便学生更形象地理解洞桩法地铁车站边桩结构的受力机制,该文以广州地区某洞桩法地铁车站工程为依托,设计了一种简化的洞桩法车站边桩结构模型试验。基于该试验方法,演示分析了边桩结构在洞桩法车站开挖过程中的施工力学行为规律,并对比研究了不同桩型布置参数下的桩后土压力、边桩结构的力学和变形规律。通过该试验,为学生展示了洞桩法边桩结构模型的设计、制作、试验具体操作及数据监测的全过程,从而让学生更好地掌握洞桩法车站边桩结构力学行为演变规律,以及采用不同边桩布置型式的力学行为差异。

钙质砂地基中群桩基础荷载传递特性研究

为研究钙质砂地基中群桩基础承载过程中的性能特征,开展不同桩距条件下群桩基础静载试验.得到不同桩距条件下群桩的Q-S曲线和S-lgt曲线,测得3d、4.5d、6d(d为桩径)群桩在静载条件下的极限承载力F_(u),研究各个桩段的桩身轴力、桩侧摩阻力以及桩端阻力的变化趋势.研究结果表明:群桩的Q-S曲线为缓变型,S-lgt曲线为渐变型,桩基承载变形大致分为稳定、渐进以及破坏3个阶段,相较于3d群桩,4.5d、6d群桩沉降发展更缓慢,F_(u)更高;同等桩距下,钙质砂地基表现出比陆源砂地基更强的群桩效应,钙质砂地基中群桩最佳桩距应在4.5d~6d之间.该研究为群桩在钙质砂地基中的应用提供数据支撑和理论参考.

扩底桩竖向承载特性及群桩效应研究

为探明扩底群桩竖向承载特性,采用扩底桩筏结构,开展单桩(扩径比分别为1.5、2.0、2.5、3.0)和桩筏(扩径比为2)基础静载模型试验,分析其荷载传递规律,并建立桩间距为3.75、4.00、4.50、5.00倍桩直径时扩底桩筏基础有限元模型,研究桩间距对群桩效应影响。结果表明:扩底单桩和扩底桩筏结构荷载沉降曲线均为缓变型;扩底桩极限承载力随扩径比增大而逐渐增大,扩径比2.5~3.0时极限承载力增幅变缓,建议扩底桩扩径比取2.5~3.0;由于桩土共同沉降,桩间土压缩,桩土作用更充分,扩底桩筏基础中心桩侧摩阻力荷载分担比比扩底单桩增大了17.71%;群桩效应系数随桩间距增大而逐渐增大,桩间距为4.5~5.0倍桩直径时群桩效应系数增幅较小,群桩效应较弱,建议扩底桩筏基础桩间距取值不小于4.5倍桩直径。