Characterization of Sludge Produced by Treatment of Water from the Ribaa and Bittit Karstic Springs (Meknes, Morocco)

Problem Statement: Surface Water Treatment for potable supplies typically involves coagulation, flocculation, and processes. All water treatment plants produce sludge, during the purification of raw water, according to the level of the water turbidity. The aluminum sulfate is the most common coagulant used in water treatment plants of Morocco, as well as in many countries all over the world. It is difficult to manage sludge produced by the treatment plant. However, several studies, based on a set of jar test experiments, have demonstrated that it can be used in the process to improve the quality of the treated water and reduce the aluminum sulfate dose. Approach: In this study, the raw water treated and sludge produced in water treatment plant of Meknes, Morocco are investigated for chemical and bacteriological proprieties. The texture characterization of the dried sludge produced through the process of coagulation/flocculation and that of aluminum sulfate, used as coagulant aid, are obtained by nitrogen adsorption isotherms. Results: The physical properties of the raw water indicate its high turbidity during periods of heavy rainfall in the Bittit and Ribaa springs catchment area. However, these chemical properties indicate the quality of fresh water rich in magnesium, related to the dolomitic nature of the liastic aquifer. The bacteriological analysis of sludge produced in the treatment plant, confirms the elimination of pathogenic germs by the treatment process used. As regards the texture characterization the results demonstrated that the sludge presents some similarities with the sulfate. However, a clear difference is observed between the two solids, according to the pores distribution. Conclusions/Recommendations: Taking aluminum sulfate and sludge in comparison, it is possible to use the sludge for improving the coagulation process in water treatment.

Information Audit Based on Image Content Filtering

At present, network information audit system is almost based on text information filtering, but badness information is embedded into image or image file directly by badness information provider, in order to avoid monitored by. The paper realizes an information audit system based on image content filtering. Taking the pornographic program identification for an example, the system can monitor the video including any abnormal human body information by matching the texture characters with those defined in advance, which consist of contrast, energy, correlation measure and entropy character measure and so on.

Through-Thickness Texture Gradient in Hot-Rolled 25Mn-2.5Si-2Al TWIP Steel

Texture is one of the important factors affecting sheet metal forming performance.The through-thickness texture gradient during the hot-rolling process of twinning induced plasticity（TWIP）steel sheet was investigated using electron backscatter diffraction and X-ray diffraction.With increasing reduction of the TWIP steel,the fraction of∑1 decreased,whereas the fractions of∑3,∑9,and∑27increased.During 53%reduction,a similar trend could be found from its surface to the center.The gradients of intensities of the fibers decreased with increasing hot-rolling reduction.The intensities of face-centered cubic（fcc）shear textures E and Y were higher in the center than that at the surface for both reductions.During 20% reduction,the intensity of fcc plain strain texture S orientation increased from the center to the surface.

Adsorption of benzene and toluene from waste gas using activated carbon activated by ZnCl2

A series of activated carbons with high surface area were prepared from walnut shell using chemical activation with ZnCl2. In this research the carbonization stage was carried out at 500℃. The performance of the synthesized carbons evaluated in adsorption of benzene and toluene from waste gas. The influence of impregnation ratio on the characteristics of synthesized activated carbons as well as their adsorption capacity was investigated. The ratio of activation agent to walnut shell was selected in the range of 0.5-2.0 wt/wt. The synthesized activated carbons were characterized using XRD, SEM, BET and FTIR techniques. The highest activated carbon production yield was obtained at impregnation ratio of 1.5 wt/wt. The XRD analysis illustrated that peaks intensity decreased with increasing impregnation ratio showing that amorphous property of samples was increased. The SEM analysis revealed successful pore development in synthesized activated carbons obtained at high impregnation ratios. The surface area of the activated carbons increased with increasing impregnation ratio and its maximum value reached 2643 m2.g 1 at impregnation ratio of 2/1. FTIR analysis indicated that the relative amount of different acidic surface groups on synthesized carbons was a function of impregnation ratio. Experimental results for benzene and toluene adsorption showed a high potential of employing synthesized impregnated activated carbon for treatment of waste gas. Generally, the amount of VOC adsorbed on the surface was affected by physicochemical properties of synthesized activated carbons.