Theoretical analysis and engineering application of controllable shock wave technology for enhancing coalbed methane in soft and low‑permeability coal seams

Coalbed methane(CBM)is a significant factor in triggering coal and gas outburst disaster,while also serving as a clean fuel.With the increasing depth of mining operations,coal seams that exhibit high levels of gas content and low permeability have become increasingly prevalent.While controllable shockwave(CSW)technology has proven effective in enhancing CBM in laboratory settings,there is a lack of reports on its field applications in soft and low-permeability coal seams.This study establishes the governing equations for stress waves induced by CSW.Laplace numerical inversion was employed to analyse the dynamic response of the coal seam during CSW antireflection.Additionally,quantitative calculations were performed for the crushed zone,fracture zone,and effective CSW influence range,which guided the selection of field test parameters.The results of the field test unveiled a substantial improvement in the gas permeability coefficient,the average rate of pure methane flowrate,and the mean gas flowrate within a 10 m radius of the antireflection borehole.These enhancements were notable,showing increases of 3 times,13.72 times,and 11.48 times,respectively.Furthermore,the field test performed on the CSW antireflection gas extraction hole cluster demonstrated a noticeable improvement in CBM extraction.After antireflection,the maximum peak gas concentration and maximum peak pure methane flow reached 71.2%and 2.59 m^(3)/min,respectively.These findings will offer valuable guidance for the application of CSW antireflection technology in soft and low-permeability coal seams.

Astronomical influence of the development of Paleogene thin coal seam groups in offshore Lacustrine basins:A case study of the ZhuⅠDepression's Enping Formation located in the northern South China Sea

The development of the Paleogene coal seams in China's offshore basin areas generally had the characteristics of coal measures with large thicknesses,large numbers of coal seams,thin single coal seams,poor stability,scattered vertical distribution,and a wide distribution range.This study selected the Enping Formation of the ZhuⅠDepression in the northern section of the South China Sea as an example to determine the macro-control factors of the development of the Paleogene coal seam groups.An analysis was carried out on the influencing effects and patterns of the astronomical cycles related to the development of the thin coal seam groups in the region.A floating astronomical time scale of the Enping Formation was established,and the sedimentary time limit of the Enping Formation was determined to be approximately 6.15 Ma±.In addition,the cyclostratigraphy analysis results of the natural gamma-ray data of Well XJ in the Enping Formation of the Xijiang Sag revealed that the development of the thin coal seams had probably been affected by short eccentricity and precession factors.The formation process of coal seams was determined to have been affected by high seasonal contrast,precipitation,and insolation.During the periods with high values of short eccentricity,the seasonal contrasts tended to be high.During those periods,fluctuations in the precession controls resulted in periodic volume changes in precipitation and insolation of the region,resulting in the development of thin coal seams.It was also found that the periods with low precession were the most conducive to coal seam development.On that basis,combined with such factors as sedimentary environmental conditions conducive to the development of thin coal seam groups,this study established a theoretical model of the comprehensive influences of short eccentricity and precession on the development and distribution of Paleogene thin coal seam groups in offshore lacustrine basins.The patterns of the Paleogene astronomical periods and paleoclimate evolution,along with the control factors which impacted the development of thin coal seam groups in offshore lacustrine basins,were revealed.

Stability analysis of longwall top-coal caving face in extra-thick coal seams based on an innovative numerical hydraulic support model

The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct virtual elements and stress servo control to approximately replace the hydraulic support problem,this paper establishes a new numerical model of hydraulic support with the same working characteristics as the actual hydraulic support by integrating numerical simulation software Rhino,Griddle and FLAC3D,which can realize the simulation of different working conditions.Based on this model,the influence mechanism of the supporting strength of hydraulic support on surrounding rock stress regulation and coal stability in front of the top coal caving face in extra thick coal seam were researched.Firstly,under different support intensity,the abutment pressure of the bearing coal and the coal in front of it presents the “three-stage”evolution characteristics.The influence range of support intensity is 15%–30%.Secondly,1.5 MPa is the upper limit of impact that the support strength can have on the front coal failure area.Thirdly,within a displacement range of 2.76 m from the coal wall,a support strength of1.5 MPa provides optimal control of the horizontal displacement of the coal.

Fracture propagation and evolution law of indirect fracturing in the roof of broken soft coal seams

Indirect fracturing in the roof of broken soft coal seams has been demonstrated to be a feasible technology.In this work,the No.5 coal seam in the Hancheng block was taken as the research object.Based on the findings of true triaxial hydraulic fracturing experiments and field pilot under this technology and the cohesive element method,a 3D numerical model of indirect fracturing in the roof of broken soft coal seams was established,the fracture morphology propagation and evolution law under different conditions was investigated,and analysis of main controlling factors of fracture parameters was conducted with the combination weight method,which was based on grey incidence,analytic hierarchy process and entropy weight method.The results show that“士”-shaped fractures,T-shaped fractures,cross fractures,H-shaped fractures,and“干”-shaped fractures dominated by horizontal fractures were formed.Different parameter combinations can form different fracture morphologies.When the coal seam permeability is lower and the minimum horizontal principal stress difference between layers and fracturing fluid injection rate are both larger,it tends to form“士”-shaped fractures.When the coal seam permeability and minimum horizontal principal stress between layers and perforation position are moderate,cross fractures are easily generated.Different fracture parameters have different main controlling factors.Engineering factors of perforation location,fracturing fluid injection rate and viscosity are the dominant factors of hydraulic fracture shape parameters.This study can provide a reference for the design of indirect fracturing in the roof of broken soft coal seams.

Research on the mechanism of rockburst induced by mined coal-rock linkage of sharply inclined coal seams

In recent years,the mining depth of steeply inclined coal seams in the Urumqi mining area has gradually increased.Local deformation of mining coal-rock results in frequent rockbursts.This has become a critical issue that affects the safe mining of deep,steeply inclined coal seams.In this work,we adopt a perspective centered on localized deformation in coal-rock mining and systematically combine theoretical analyses and extensive data mining of voluminous microseismic data.We describe a mechanical model for the urgently inclined mining of both the sandwiched rock pillar and the roof,explaining the mechanical response behavior of key disaster-prone zones within the deep working face,affected by the dynamics of deep mining.By exploring the spatial correlation inherent in extensive microseismic data,we delineate the“time-space”response relationship that governs the dynamic failure of coal-rock during the progression of the sharply inclined working face.The results disclose that(1)the distinctive coal-rock occurrence structure characterized by a“sandwiched rock pillar-B6 roof”constitutes the origin of rockburst in the southern mining area of the Wudong Coal Mine,with both elements presenting different degrees of deformation localization with increasing mining depth.(2)As mining depth increases,the bending deformation and energy accumulation within the rock pillar and roof show nonlinear acceleration.The localized deformation of deep,steeply inclined coal-rock engenders the spatial superposition of squeezing and prying effects in both the strike and dip directions,increasing the energy distribution disparity and stress asymmetry of the“sandwiched rock pillar-B3+6 coal seam-B6 roof”configuration.This makes worse the propensity for frequent dynamic disasters in the working face.(3)The developed high-energy distortion zone“inner-outer”control technology effectively reduces high stress concentration and energy distortion in the surrounding rock.After implementation,the average apparent resistivity in the rock pillar and B6 roof substantially increased by 430%and 300%,respectively,thus guaranteeing the safe and efficient development of steeply inclined coal seams.

Analysis of the Risk of Water Breakout in the Bottom Plate of High-Intensity Mining of Extra-Thick Coal Seams

In order to clarify the danger of water breakout in the bottom plate of extra-thick coal seam mining, 2202 working face of a mine in the west is taken as the research object, and it is proposed to use the on-site monitoring means combining borehole peeping and microseismic monitoring, combined with the theoretical analysis to analyze the danger of water breakout in the bottom plate. The results show that: 1) the theoretically calculated maximum damage depth of the bottom plate is 27.5 m, and its layer is located above the Austrian ash aquifer, which has the danger of water breakout;2) the drill hole peeping at the bottom plate of the working face shows that the depth of the bottom plate fissure development reaches 26 m, and the integrity of the water barrier layer has been damaged, so there is the risk of water breakout;3) for the microseismic monitoring of the anomalous area, the bottom plate of the return air downstream channel occurs in the field with a one-week lag, which shows that microseismic monitoring events may reflect the water breakout of the underground. This shows that the microseismic monitoring events can reflect the changes of the underground flow field, which can provide a reference basis for the early warning of water breakout. The research results can provide reference for the prediction of sudden water hazard.

Insights into carbon dioxide sequestration into coal seams through coupled gas flow-adsorption-deformation modelling

Injecting carbon dioxide(CO_(2))into coal seams may unlock substantial carbon sequestration potential.Since the coal acts like a carbon filter,it can preferentially absorb significant amounts of CO_(2).To explore this further,desorption of the adsorbed gas due to pressure drop is investigated in this paper,to achieve an improved understanding of the long-term fate of injected CO_(2) during post-injection period.This paper presents a dual porosity model coupling gas flow,adsorption and geomechanics for studying coupled processes and effectiveness of CO_(2) sequestration in coals.A new adsorption?desorption model derived based on thermodynamics is incorporated,particularly,the desorption hysteresis is considered.The reliability of the proposed adsorption-desorption isotherm is examined via validation tests.It is indicated that occurrence of desorption hysteresis is attributed to the adsorption-induced pore deformation.After injection ceases,the injected gas continues to propagate further from the injection well,while the pressure in the vicinity of the injection well experiences a significant drop.Although the adsorbed gas near the well also decreases,this decrease is less compared to that in pressure because of desorption hysteresis.The unceasing spread of CO_(2) and drops of pressure and adsorbed gas depend on the degree of desorption hysteresis and heterogeneity of coals,which should be considered when designing CO_(2) sequestration into coal seams.

Further Information of the Associated Li Deposits in the No.6 Coal Seam at Jungar Coalfield, Inner Mongolia, Northern China

Total 138 coal samples and 14 parting samples were taken from the No. 6 Seam of the Jungar Coalfield, Inner Mongolia. These samples were analysed by optical microscopy, sequential chemical extraction procedure （SCEP）, inductively coupled plasma mass spectrometry （ICP-MS）, X-ray powder diffraction （XRD）, and scanning electron microscope in conjunction with an energy-dispersive X-ray spectrometer （SEM-EDX） analysis. The results indicate that the Li contents have reached the industrial grade of the coal associated Li deposit, and the total Li reserves have reached 2406600 tons, that is, 5157000 tons Li2O in the No. 6 seam in the Jungar Coalfield. The sequential chemical extraction procedure results suggest that the Li concentration is mainly related to inorganic matter. The minerals in the coals consist of kaolinite, boehmite, chlorite-group mineral, quartz, calcite, pyrite, siderite and amorphous clay material. Some Li could be absorbed by clay minerals in the Li-bearing coal seam. The chlorite phase？could be？most likely the host for a part of Li. The Yinshan Oldland should be the most possible source of Li of the coal.

Research into comprehensive gas extraction technology of single coal seams with low permeability in the Jiaozuo coal mining area

For a low permeability single coal seam prone to gas outbursts, pre-drainage of gas is difficult and inefficient, seriously restricting the safety and efficiency of production. Radical measures of increasing gas extraction efficiency are pressure relief and infrared antireflection. We have analyzed the effect of mining conditions and the regularity of mine pressure distribution in front of the working face of a major coal mine of the Jiaozuo Industrial （Group） Co. as our test area, studied the width of the depressurization zone in slice mining and analyzed gas efficiency and fast drainage in the advanced stress relaxation zone. On that basis, we further investigated and practiced the exploitation technology of shallow drilling, fan dril- ling and grid shape drilling at the working face. Practice and our results show that the stress relaxation zone is the ideal region for quick and efficient extraction of gas. By means of an integrated extraction technology, the amount of gas emitted into the zone was greatly reduced, while the risk of dangerous outbursts of coal and gas was lowered markedly. This exploration provides a new way to control for gas in working faces of coal mines with low permeability and risk of gas outbursts of single coal seams in the Jiaozuo mining area.

Study on the non-linear forecast method for water inrush from coal seam floor based on wavelet neural network

Directing at the non-linear dynamic characteristics of water inrush from coal seam floor and by the analysis of the shortages of current forecast methods for water inrush from coal seam floor, a new forecast method was raised based on wavelet neural network （WNN） that was a model combining wavelet function with artificial neural network. Firstly basic principle of WNN was described, then a forecast model for water inrush from coal seam floor based on WNN was established and analyzed, finally an example of forecasting the quantity of water inrush from coal floor was illustrated to verify the feasibility and superiority of this method. Conclusions show that the forecast result based on WNN is more precise and that using WNN model to forecast the quantity of water inrush from coal seam floor is feasible and practical.

Discussion of the indexes of nonoutburst coal seam upgrade and its corresponding critical values

In view of the measurement difficulties of indexes recommended by the 50Items Experience of Coal Mine Gas Prevention in the process of the nonoutburst coalseam upgrade, this paper took the No.8 coal seam of Huainan Mining Group as research object. Discussed the suitability of indexes and corresponding critical values, putforward method in determining the indexes and its critical values by analysis and investigation of the gas geological condition and the-spot tracking near position where anoutburst occurred combined with laboratory experiment, and established the indexesand its critical values of nonoutburst coal seam upgrade in No.8 coal seam of HuainanMining Group. The results show that it is suitable to take gas content and tectonic softcoal thickness easily to gain in routine production as primary upgrade indexes that itscritical values are 7.5 m^3/t and 0.8 m, respectively. In addition, takefvalue and Ap valueas auxiliary indexes.

The adjusting mining technology of combining fully mechanized with individual prop,rotating,hilt,irregular form,and double unit face on thin coal seam of Tianchen Mine

Analyzed the situations and characteristics of thin coal seam mining and its mining technologies,and introduced the mining innovation technology used by Tianchen Coal Mine of Zhaozhuang Coal Company of China.This innovation technology combined the fully mechanized mining with individual props,and the working face of mining is over length,irregular form and double units.The rotational adjusting mining technology on thin coal seam is also practiced in this new mining technology.The detail technologies,such as outlays of working face and ways,mining methods,equipments of cutting,transporting and sporting,have been introduced.So that,using the synthetic and creative mining tech- nologies,Tianchen Coal Mine solves the mining problems of thin coal seam successfully.

Study on the economic mining method for the close quarter coal seams with thin rock sheet

The paper presents the mining method for the close quarter coal seams with thin rock sheet, that is mining the low coal seam, recovering the top coal seam after putting down the roof rock of the low coal seam. Practice has proved that in recovering the top coal outside the face width after the rock between seams falls naturally or is demolished, the technology is simple, easy to operate and does not make a great demand for technical equipment. In the process of recovering the top coal, the low seam support could not be affected seriously, and two seams mining could be coordinated. Compared with the individual mining method, this mining method can produce a better economic benefit.

Back-and-forth mining for hard and thick coal seams—research about the mining technology for fully mechanized caving working face of Datong Mine

The article introduced the key technology, mining process, and back-and-forth mining method for the caving working face of hard-thick coal seams in Datong mine, and researched this innovations process, optimized the systemic design and working face out-play, tried to perfect the caving mining technology of hard-thick coal seams further.

LaMnO_(3)钙钛矿型复合氧化物催化氧化燃煤烟气单质汞的性能研究

为充分利用锰氧化物在低温下的高活性以及钙钛矿结构较强的表面活性氧流动能力,采用合成的LaMnO_(3)来处理燃煤烟气中的汞,并对合成的LaMnO_(3)进行一系列的物理化学特征表征。结果表明:催化剂比表面积较小,但其表面的氧浓度高于理论值,且锰离子呈+3价与+4价的混合价态;催化剂表面可参与汞氧化过程的的活性氧较少,但流动性较强,体积分数3%的O2足够使催化剂维持高氧化率;HCl可以显著增强催化剂对单质汞的催化氧化活性,说明催化剂表面的大部分氧物种均可与HCl反应生成有利于单质汞氧化的活性氯。

Hydraulic fracture initiation theory for a horizontal well in a coal seam

A series of experiments were pertbrmed to determine rock mechanical parameters related to hydraulic fracturing of coal. The effect of confining pressure and pore pressure on the strength of coal was stt, died. Experimental results show that the coal seam in the study areas has a relatively low elastic modulus, high Poisson＇s ratio, high fragility and is easily broken and compressed. The coal seam is considered as a transversely isotropic medium, since the physical properties in the direction of bedding plane and orthogonal to the bedding plane vary markedly. Based on the generalized plane strain model, stress distribution for an arbitrarily orientated wellbore in the coal seam was determined. In a horizontal well, hydraulic fracturing was lbund to initiate in the coal seam mass due to tensile failure, or from cleats due to shear or tensile failure. For those coal seams with abundant natural cleats, hydraulic fracture initiation can be induced by any of these mechanisms. In this study, hydraulic fracture initiation criteria tbr a horizontal well in a coal seam were established.

The impact of cleats on hydraulic fracture initiation and propagation in coal seams

Cleats are systematic, natural fractures in coal seams. They account for most of the permeability and much of the porosity of coalbed methane reservoirs and can have a significant effect on the success of hydraulic fracturing stimulation. Laboratory hydraulic fracturing experiments were conducted on coal blocks under true tri-axial stress to simulate fracturing stimulation of coal seams. Fractures were initiated by injecting a water gel with luminous yellow fluorescent dye into an open hole section of a wellbore. The impact of cleats on initiation and propagation of hydraulic fractures in coal seams is discussed. Three types of hydraulic fracture initiation and propagation pattern were observed in this study： 1） The hydraulic fracture initiated and then grew along the cleat. 2） The hydraulic fracture initiated along a butt cleat or a fracture （natural or induced by drilling） oriented roughly in the minimum horizontal stress direction, then turned to propagate along the first face cleat that it encountered or gradually turned towards the maximum horizontal stress direction. 3） The hydraulic fracture initiated perpendicular to the minimum stress and, when it encountered a face cleat, tended to propagate along the cleats if the extension direction does not deviate greatly （〈20° as determined in this paper） from the maximum horizontal stress direction. When a coal seam is hydraulically fractured, the resulting fracture network is controlled by the combined effect of several factors： cleats determine the initiation and extension path of the fracture, the in-situ stress state dominates the main direction of the fracture zone and bedding planes impede fracture height growth.

氧浓度对氨煤混燃高温还原区NH_(3)/煤焦/NO异相还原的影响

在煤粉炉中掺入无碳燃料氨可有效降低火电CO_(2)排放,近几年引起了越来越多的关注。然而,氨混烧增加了NO_(x)生成途径,研究氨煤混烧过程高温还原区NO的还原机理对实现氨煤混燃低氮排放尤为关键。高温还原区并非无氧环境,探究还原区微氧对未燃氨耦合煤焦还原NO的影响机理十分必要。利用高温水平管式炉研究了O_(2)体积分数(0、0.5%、1.0%、1.5%、2.0%)对NH_(3)/NO均相以及NH_(3)/煤焦/NO异相还原的影响机理,温度在1373~1773 K。研究结果表明,高温无氧环境下,随着温度升高,NH_(3)均相还原NO的效率增加;当温度高于1573 K时,NH_(3)均相还原NO随温度的升高略微降低,未燃氨对NO的最佳还原温度为1573 K。而煤焦的存在显著提高了高温下NH_(3)还原NO的效率,且将NO的最佳还原温度拓宽到1673 K,煤焦与NH_(3)对NO的还原表现为协同促进作用。相对于无氧条件,O_(2)体积分数在2.0%、温度不高于1500 K时,微氧促进了还原性自由基NH_(2)/NH的生成,对NH_(3)/NO的均相还原表现为促进作用;进一步升高温度,有利于体系内NH_(2)/NH的氧化,使得有氧条件下NH_(3)均相还原NO的效率低于无氧条件。NH_(3)/煤焦/NO的异相还原体系中,当温度不高于1473 K以及O_(2)体积分数不高于0.5%时,微氧条件下的NO异相还原效率高于无氧条件;但当O_(2)体积分数和温度的进一步提高,NHi与OH/O等氧化性自由基的氧化反应相较于NHi/煤焦还原NO过程的速率更快时,NH_(3)/煤焦/NO异相体系内NO的还原效率降低,表明存在促进高温还原区NH_(3)/煤焦异相还原NO的最佳O_(2)体积分数。

Evolution of a mining induced fracture network in the overburden strata of an inclined coal seam

The geological conditions of the Pingdingshan coal mining group were used to construct a physical model used to study the distribution and evolution of mining induced cracks in the overburden strata.Digital graphics technology and fractal theory are introduced to characterize the distribution and growth of the mining induced fractures in the overburden strata of an inclined coal seam.A relationship between fractal dimension of the fracture network and the pressure in the overburden strata is suggested.Mining induced fractures spread dynamically to the mining face and up into the roof as the length of advance increases.Moreover,the fractal dimension of the fracture network increases with increased mining length,in general,but decreases during a period from overburden strata separation until the main roof collapses.It is a1so shown that overburden strata pressure plays an important role in the evolution of mining induced fractures and that the fractal dimension of the fractures increases with the pressure of the overburden.

Influential factors and control of water inrush in a coal seam as the main aquifer

In this paper, a combination of field measurement, theoretical analysis and numerical simulation were used to study the main control factors of coal mine water inrush in a main aquifer coal seam and its control scheme. On the basis of revealing and analyzing the coal seam as the main aquifer in western coal mine of Xiao Jihan coal mine, the simulation software of PHASE-2D was applied to analyze the water inflow under different influencing factors. The results showed that water inflow increases logarithmically with the coal seam thickness, increases as a power function with the permeability coefficient of the coal seam, and increases linearly with the coal seam burial depth and the head pressure; The evaluation model for the factors of coal seam water inrush was gained by using nonlinear regression analysis with SPSS. The mine water inrush risk evaluation partition within the scope of the mining field was obtained,through the engineering application in Xiao Jihan coal mine. To ensure the safe and efficient production of the mine, we studied the coal mine water disaster prevention and control measures of a main aquifer coal seam in aspects of roadway driving and coal seam mining.