An active pipe-embedded building envelope, which is an external wall or roof with pipes embedded inside, was presented. This structure may utilize the circulating water in the pipe to transfer heat or coolth inside di...An active pipe-embedded building envelope, which is an external wall or roof with pipes embedded inside, was presented. This structure may utilize the circulating water in the pipe to transfer heat or coolth inside directly. This kind of structure is named ＂active pipe-embedded building envelope＂ due to dealing with the thermal energy actively inside the structure mass by circulating water. This structure not only deals with thermal energy before the external disturbance becomes cooling/heating load by using the circulating water, but also may use low-grade energy sources such as evaporative cooling, solar energy, and geothermal energy. In the meantime, this structure can also improve the indoor thermal comfort by tempering the internal wall surface temperature variation due to the thermal removal in the mass. This work further presents the thermal performance of this structure under a typical hot summer weather condition by comparing it with that of the conventional external wall/roof with numerical simulation. The results show that this pipe-embedded structure may reduce the external heat transfer significantly and reduce the internal wall surface temperature for improving thermal comfort. This work also presents the effects of the water temperature and the pipe spacing on the heat transfer of this structure. The internal surface heat transfer may reduce by about 2.6 W/mE when the water temperature reduces by 1℃ as far as a brick wall with pipes embedded inside is concerned. When the pipe spacing reduces by 50 mm, the internal wall surface heat flux can also reduce by about 2.3 W/m2.展开更多
A variety of liquid thermal solar collectors designs used for water heating have been developed by the previous researchers. But the majority of them do not meet the requirements on small weight, easy assembling and i...A variety of liquid thermal solar collectors designs used for water heating have been developed by the previous researchers. But the majority of them do not meet the requirements on small weight, easy assembling and installing, versatility, scalability and adaptability of the design, which are particularly important when they are facade integrated. In order to avoid the above mentioned drawbacks of the liquid thermal collectors, the authors propose to apply to them extruded aluminum alloy made heat pipes of originally designed cross-sectional profile with wide fins and longitudinal grooves. Such solar collectors could be a good solution for building facade and roof integration, because they are assembled of several standard and independent, hermetically sealed and light-weight modules, easy mounted and ＂dry＂ connected to the main pipeline. At that, their thermal performances are not worse than of the other known ones made of heavier and more expensive copper with higher thermal conductance, or having entire rigid designs. Some variants of the developed solar collectors shaping of the assembled modules for building facade or roof integration are proposed. Variously colored coatings to the absorbers are developed and made of carbon-siliceous nano-composites by means of sol-gel method. Their optical performances were compared with ＂anodized black＂. It is stated that colored coatings have a good prospect in thermal SCs （solar collectors） adaptation to building facades decoration, but the works on study and upgrade of their performances should be continued.展开更多
An intelligent design software system for the power station pipe-prefabrication (PPDS) has been developed in the paper,which is taking pipe material database as core and developed on the platform of AutoCAD and Borlan...An intelligent design software system for the power station pipe-prefabrication (PPDS) has been developed in the paper,which is taking pipe material database as core and developed on the platform of AutoCAD and Borland C++. Whereas design and construction of power plants in China belong to different deportments,the input and recognition problem of pipeline system disposition chart must be solved firstly for the prefabrication design.Based on AI technology,the model fast building subsystem (MFBS) was established for entering the 3-D pipeline graph data,so that the problems of reconstruction of pipeline digital model and computer identification of original 2-D design data can be solved. The optimization design scheme in the pipe-prefabrication process has been studied and also the corresponding algorithm put forward.The technique and system mentioned can effectively raise the pipe-prefabrication design quality and efficiency in the con- struction of large scale power plants,reduce the period of design and the waste of raw material.PPCADS has still offered the functions such as the construction design for pipeline prefabricated process,the detailing drawing for manufacturing pipe section and automatic generating the technical files for the completed project.展开更多
为提高相变屋面的性能,本文提出了一种冷却塔-内嵌管式相变屋面复合降温系统。基于焓法,建立了系统的数值计算传热模型,数值研究了该系统在福州地区的热性能及节能潜力,探讨了相变材料相变温度、相变材料导热系数以及内嵌管间距的影响,...为提高相变屋面的性能,本文提出了一种冷却塔-内嵌管式相变屋面复合降温系统。基于焓法,建立了系统的数值计算传热模型,数值研究了该系统在福州地区的热性能及节能潜力,探讨了相变材料相变温度、相变材料导热系数以及内嵌管间距的影响,并与传统的无内嵌管相变屋面进行了对比分析。研究发现,相变温度越高,复合降温系统的相变材料越容易完成凝固,但潜热利用率随相变温度的升高呈现先增加后降低的趋势。当相变温度由35℃升高到41℃时,屋面的累计冷负荷由383 k J/m^(2)增大到400 k J/m^(2),增加了4.4%。相变材料导热系数越高、内嵌管间距越小,复合降温系统相比于传统无内嵌管相变屋面的潜热利用优势越显著。当导热系数由0.2 W/(m·K)增加到0.8 W/(m·K)时,复合降温系统的潜热利用率和屋面累计冷负荷分别增加了36.3%和5.1%,而无内嵌管相变屋面的潜热利用率和屋面累计冷负荷分别升高了33.1%和6.3%。当内嵌管间距由500 mm减少到100 mm时,复合降温系统比传统无内嵌管相变屋面的潜热利用提高率由2.7%增大到16.3%,累计冷负荷降低率由3.8%升高到10.9%。研究结果可促进建筑节能和双碳目标的实现。展开更多
基金Project(51178201) supported by the National Natural Science Foundation of China Project(2011CDB292) supported by the Natural Science Foundation of Hubei Province,China
文摘An active pipe-embedded building envelope, which is an external wall or roof with pipes embedded inside, was presented. This structure may utilize the circulating water in the pipe to transfer heat or coolth inside directly. This kind of structure is named ＂active pipe-embedded building envelope＂ due to dealing with the thermal energy actively inside the structure mass by circulating water. This structure not only deals with thermal energy before the external disturbance becomes cooling/heating load by using the circulating water, but also may use low-grade energy sources such as evaporative cooling, solar energy, and geothermal energy. In the meantime, this structure can also improve the indoor thermal comfort by tempering the internal wall surface temperature variation due to the thermal removal in the mass. This work further presents the thermal performance of this structure under a typical hot summer weather condition by comparing it with that of the conventional external wall/roof with numerical simulation. The results show that this pipe-embedded structure may reduce the external heat transfer significantly and reduce the internal wall surface temperature for improving thermal comfort. This work also presents the effects of the water temperature and the pipe spacing on the heat transfer of this structure. The internal surface heat transfer may reduce by about 2.6 W/mE when the water temperature reduces by 1℃ as far as a brick wall with pipes embedded inside is concerned. When the pipe spacing reduces by 50 mm, the internal wall surface heat flux can also reduce by about 2.3 W/m2.
文摘A variety of liquid thermal solar collectors designs used for water heating have been developed by the previous researchers. But the majority of them do not meet the requirements on small weight, easy assembling and installing, versatility, scalability and adaptability of the design, which are particularly important when they are facade integrated. In order to avoid the above mentioned drawbacks of the liquid thermal collectors, the authors propose to apply to them extruded aluminum alloy made heat pipes of originally designed cross-sectional profile with wide fins and longitudinal grooves. Such solar collectors could be a good solution for building facade and roof integration, because they are assembled of several standard and independent, hermetically sealed and light-weight modules, easy mounted and ＂dry＂ connected to the main pipeline. At that, their thermal performances are not worse than of the other known ones made of heavier and more expensive copper with higher thermal conductance, or having entire rigid designs. Some variants of the developed solar collectors shaping of the assembled modules for building facade or roof integration are proposed. Variously colored coatings to the absorbers are developed and made of carbon-siliceous nano-composites by means of sol-gel method. Their optical performances were compared with ＂anodized black＂. It is stated that colored coatings have a good prospect in thermal SCs （solar collectors） adaptation to building facades decoration, but the works on study and upgrade of their performances should be continued.
文摘An intelligent design software system for the power station pipe-prefabrication (PPDS) has been developed in the paper,which is taking pipe material database as core and developed on the platform of AutoCAD and Borland C++. Whereas design and construction of power plants in China belong to different deportments,the input and recognition problem of pipeline system disposition chart must be solved firstly for the prefabrication design.Based on AI technology,the model fast building subsystem (MFBS) was established for entering the 3-D pipeline graph data,so that the problems of reconstruction of pipeline digital model and computer identification of original 2-D design data can be solved. The optimization design scheme in the pipe-prefabrication process has been studied and also the corresponding algorithm put forward.The technique and system mentioned can effectively raise the pipe-prefabrication design quality and efficiency in the con- struction of large scale power plants,reduce the period of design and the waste of raw material.PPCADS has still offered the functions such as the construction design for pipeline prefabricated process,the detailing drawing for manufacturing pipe section and automatic generating the technical files for the completed project.
文摘为提高相变屋面的性能,本文提出了一种冷却塔-内嵌管式相变屋面复合降温系统。基于焓法,建立了系统的数值计算传热模型,数值研究了该系统在福州地区的热性能及节能潜力,探讨了相变材料相变温度、相变材料导热系数以及内嵌管间距的影响,并与传统的无内嵌管相变屋面进行了对比分析。研究发现,相变温度越高,复合降温系统的相变材料越容易完成凝固,但潜热利用率随相变温度的升高呈现先增加后降低的趋势。当相变温度由35℃升高到41℃时,屋面的累计冷负荷由383 k J/m^(2)增大到400 k J/m^(2),增加了4.4%。相变材料导热系数越高、内嵌管间距越小,复合降温系统相比于传统无内嵌管相变屋面的潜热利用优势越显著。当导热系数由0.2 W/(m·K)增加到0.8 W/(m·K)时,复合降温系统的潜热利用率和屋面累计冷负荷分别增加了36.3%和5.1%,而无内嵌管相变屋面的潜热利用率和屋面累计冷负荷分别升高了33.1%和6.3%。当内嵌管间距由500 mm减少到100 mm时,复合降温系统比传统无内嵌管相变屋面的潜热利用提高率由2.7%增大到16.3%,累计冷负荷降低率由3.8%升高到10.9%。研究结果可促进建筑节能和双碳目标的实现。
