This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of con...This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.展开更多
Resistive Plate Chambers(RPCs) built from a new type of Bakelite developed at Institute of High Energy Physics(IHEP),Chinese Academy of Sciences have been used in the BESⅢ Muon identification system for several years...Resistive Plate Chambers(RPCs) built from a new type of Bakelite developed at Institute of High Energy Physics(IHEP),Chinese Academy of Sciences have been used in the BESⅢ Muon identification system for several years without linseed oil coating,but characteristic aging performances were observed.To adapt to the RPCs in the aging state,the front-end electronics have been upgraded by enhancing the front-end protection,improving the threshold setting circuit,and separating power supplies of the comparator and the field programmable gate array(FPGA).Improvements in system stability,front-end protection and threshold consistency have been achieved.In this paper,the system upgrade and the test results are described in detail.展开更多
The saving of non-renewable energies, as well as the reduction of emissions into the environment, are two crucial objectives of industrial production. The recovery of post-consumer products associated with the use of ...The saving of non-renewable energies, as well as the reduction of emissions into the environment, are two crucial objectives of industrial production. The recovery of post-consumer products associated with the use of end-of-life products is part of a context of optimization of these objectives. This recovery maximizes the use of resources from end-of-life products in a circular logic while recording the environmental footprint. This study considers a recycling strategy adapted to the need and urgency to reduce greenhouse gas emissions caused by global warming. The proposed model aims to optimize the profits of the circular manufacturing strategies while minimizing operational costs (collection, sorting, recycling), transport, GHG emissions and recycling. In this paper, a compromise between the gains of CM and the costs associated with it was studied. The robustness of the designed model was tested using a case study based on real-world scenarios. A sensitivity analysis was carried out to study the impact of the emission cost on the overall objective, considering the two options currently offered to industries. The obtained results support companies to take the ecological aspect into account and integrate sustainable development into their strategic axes for their logistics supply chains.展开更多
A series of well-designed full-scale destructive load tests were conducted on six bored piles to investigate the influence of loose debris at the pile tip on end resistance. The results show that soft debris below the...A series of well-designed full-scale destructive load tests were conducted on six bored piles to investigate the influence of loose debris at the pile tip on end resistance. The results show that soft debris below the pile tip will weaken the mobilization of end resistance. The ultimate tip resistance of post-grouted pile is 2.05 times that of the pile without post-grouting and the ultimate tip resistance in the second load cycle is 2.31 times that of pile in the first load cycle. The relationship between unit end resistance and displacement follows a linear model and a bilinear mode in the first load cycle and the second load cycle, respectively, whereas the unit end resistance-displacement response of post-grouted bored pile can be simulated using a bilinear mode. The critical end resistance ranges between 2 000 kN and 3 000 kN and the critical displacement ranges between 2.5 mm and 4.5 mm in the bilinear mode. As for piles rested on moderately-weathered peliticsiltstone, the socketed length has no effect on the end resistance because of the existence of loose debris.展开更多
Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well ceme...Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.展开更多
ITO (indium oxide doped with tin) thin films were deposited on glass substrates by using ITO pellet with a composition of w(In2O3)=90% and w(SnO2)=10% by electron beam evaporated with End-Hall ion source assiste...ITO (indium oxide doped with tin) thin films were deposited on glass substrates by using ITO pellet with a composition of w(In2O3)=90% and w(SnO2)=10% by electron beam evaporated with End-Hall ion source assisted without extra heating. The rate of deposition and flow rate of oxygen were measured and changed to obtain the best properties of ITO thin films. Furthermore, the post annealing process was done in vacuum at different annealing temperatures for 2 h and at 400℃ for different keeping time, respectively. The relation between optical, electrical properties and structure was discussed in detail.展开更多
Spontaneous bacterial peritonitis(SBP) is the most common infection in end-stage liver disease patients.SBP is defined as an ascitic fluid infection with a polymorphonuclear leucocyte count ≥ 250/mm^3 without an evid...Spontaneous bacterial peritonitis(SBP) is the most common infection in end-stage liver disease patients.SBP is defined as an ascitic fluid infection with a polymorphonuclear leucocyte count ≥ 250/mm^3 without an evident intra-abdominal surgically treatable source.Several mechanisms contribute to SBP occurrence,including translocation of gut bacteria and their products,reduced intestinal motility provoking bacterial overgrowth,alteration of the gut's barrier function and local immune responses.Historically,Gram-negative enteric bacteria have been the main causative agents of SBP,thereby guiding the empirical therapeutic choice.However,over the last decade,a worryingly increasing prevalence of Gram-positive and multi-drug resistant(MDR) SBP has been seen.Recently,the microbiological spectrum of SBP seems to have changed in Europe due to a high prevalence of Gram-positive bacteria(48%-62%).The overall proportion of MDR bacteria is up to 22%-73% of cases.Consequently,empirical therapy based on thirdgeneration cephalosporins or amoxicillin/clavulanic acid,can no longer be considered the standard of care,as these drugs are associated with poor outcomes.Theaim of this review is to describe,with an epidemiological focus,the evidence behind this rise in Gram-positive and MDR SBP from 2000 to present,and illustrate potential targeted therapeutic strategies.An appropriate treatment protocol should include daptomycin plus ceftaroline and meropenem,with prompt stepdown to a narrower spectrum when cultures and sensitivity data are available in order to reduce both cost and potential antibiotic resistance development.展开更多
Chemotherapy resistance plays a pivotal role in the prognosis and therapeutic failure of patients with colorectal cancer(CRC).Cisplatin(DDP)-resistant cells exhibit an inherent ability to evade the toxic chemotherapeu...Chemotherapy resistance plays a pivotal role in the prognosis and therapeutic failure of patients with colorectal cancer(CRC).Cisplatin(DDP)-resistant cells exhibit an inherent ability to evade the toxic chemotherapeutic drug effects which are characterized by the activation of slow-cycle programs and DNA repair.Among the elements that lead to DDP resistance,O^(6)-methylguanine(O^(6)-MG)-DNA-methyltransferase(MGMT),a DNA-repair enzyme,performs a quintessential role.In this study,we clarify the significant involvement of MGMT in conferring DDP resistance in CRC,elucidating the underlying mechanism of the regulatory actions of MGMT.A notable upregulation of MGMT in DDP-resistant cancer cells was found in our study,and MGMT repression amplifies the sensitivity of these cells to DDP treatment in vitro and in vivo.Conversely,in cancer cells,MGMT overexpression abolishes their sensitivity to DDP treatment.Mechanistically,the interaction between MGMT and cyclin dependent kinase 1(CDK1)inducing slow-cycling cells is attainted via the promotion of ubiquitination degradation of CDK1.Meanwhile,to achieve nonhomologous end joining,MGMT interacts with XRCC6 to resist chemotherapy drugs.Our transcriptome data from samples of 88 patients with CRC suggest that MGMT expression is co-related with the Wnt signaling pathway activation,and several Wnt inhibitors can repress drug-resistant cells.In summary,our results point out that MGMT is a potential therapeutic target and predictive marker of chemoresistance in CRC.展开更多
With rapid development of the semiconductor technology, more efficient cooling systems for electronic devices are needed. In this situation, in the present study, a loop thermosyphon type cooling system, which is comp...With rapid development of the semiconductor technology, more efficient cooling systems for electronic devices are needed. In this situation, in the present study, a loop thermosyphon type cooling system, which is composed mainly of a heating block, an evaporator and an air-cooled condenser, is investigated experimentally in order to evaluate the cooling performance. At first, it is examined that the optimum volume filling rate of this cooling system is approximately 40%. Next, four kinds of working fluids, R1234ze(E), R1234ze(Z), R134a and ethanol, are tested using a blasted heat transfer surface of the evaporator. In cases of R1234ze(E), R1234ze(Z), R134a and ethanol, the effective heat flux, at which the heating block surface temperature reaches 70°C, is 116 W/cm2, 106 W/cm2, 104 W/cm2 and 60 W/cm2, respectively. This result indicates that R1234ze(E) is the most suitable for the present cooling system. The minimum boiling thermal resistance of R1234ze(E) is 0.05 (cm2·K)/W around the effective heat flux of 100 W/cm2. Finally, four kinds of heat transfer surfaces of the evaporator, smooth, blasted, copper-plated and finned surfaces, are tested using R1234ze(E) as working fluid. The boiling thermal resistance of the blasted surface is the smallest among tested heat transfer surfaces up to 116 W/cm2 in effective heat flux. However, it increases drastically due to the appearance of dry-patch if the effective heat flux exceeds 116 W/cm2. On the other hand, in cases of copper-plated and finned surfaces, the dry-patch does not appear up to 150 W/cm2 in effective heat flux, and the boiling thermal resistances of those surfaces keep 0.1 (cm2·K)/W.展开更多
This paper presents an analysis of the effect of parasitic resistances on the performance of DC-DC Single Ended Pri- mary Inductor Converter (SEPIC) in photovoltaic maximum power point tracking (MPPT) applications. Th...This paper presents an analysis of the effect of parasitic resistances on the performance of DC-DC Single Ended Pri- mary Inductor Converter (SEPIC) in photovoltaic maximum power point tracking (MPPT) applications. The energy storage elements incorporated in the SEPIC converter possess parasitic resistances. Although ideal components significantly simplifies model development, but neglecting the parasitic effects in models may sometimes lead to failure in predicting first scale stability and actual performance. Therefore, the effects of parasitics have been taken into consideration for improving the model accuracy, stability, robustness and dynamic performance analysis of the converter. Detail mathematical model of SEPIC converter including inductive parasitic has been developed. The performance of the converter in tracking MPP at different irradiance levels has been analyzed for variation in parasitic resistance. The converter efficiency has been found above 83% for insolation level of 600 W/m2 when the parasitic resistance in the energy storage element has been ignored. However, as the parasitic resistance of both of the inductor has increased to 1 ohm, a fraction of the power managed by the converter has dissipated;as a result the efficiency of the converter has reduced to 78% for the same insolation profile. Although the increasing value of the parasitic has assisted the converter to converge quickly to reach the maximum power point. Furthermore it has also been observed that the peak to peak load current ripple is reduced. The obtained simulation results have validated the competent of the MPPT converter model.展开更多
Adeno-associated virus(AAV) is a single-stranded linear defective parvovirus. Using the model proposed by Cavalier-Smith for replication of ss-DNA virus. the linear fragment of inverted terminal repeats(ITRs) from PAA...Adeno-associated virus(AAV) is a single-stranded linear defective parvovirus. Using the model proposed by Cavalier-Smith for replication of ss-DNA virus. the linear fragment of inverted terminal repeats(ITRs) from PAAV/neo was isolated, denatured and refolded over. The daughter DNA was synthesized by using 3'-OH terminus as a primer with the new strand covalently linked to the parental strand. After the palindromic structure with neomycin resistance gene controlled by SV40 early promoter into eukaryotic cells. Southern blot showed that the molecule of hairpin structure could facilitate the copies into mammalian cells in vitro. The experiment supports the Cavalier-Smith's replication model of ss-DNA virus and provides another new system for DNA transduction.展开更多
One resistance gene analog fragment named RGA-CIN14 was isolated from TcLr19 wheat,which contains kinase-2,kinase-3a,and the GLPL motif of the NBS-spanning region,using degenerated primers according to the nucleotide ...One resistance gene analog fragment named RGA-CIN14 was isolated from TcLr19 wheat,which contains kinase-2,kinase-3a,and the GLPL motif of the NBS-spanning region,using degenerated primers according to the nucleotide binding site (NBS) conserved domain.Based on the RGA-CIN14,a full-length cDNA,CIN14,which was 2 987 bp encoding 880 amino acids,was obtained by using the method of the rapid amplification cDNA ends (RACE).Bioinformatics analysis showed that the deduced amino acids of CIN14 protein consisted of a NB-ARC conserved domain and many leucine-rich repeats (LRR) domains.The phylogenetic tree analysis indicated a considerable identity of the protein encoded by CIN14 with that of wheat leaf rust resistance gene Lr1,but a lower similarity with Lr21.The expression profile of the CIN14 gene detected by semi-quantitative RT-PCR showed that the CIN14 gene was not induced by Puccinia triticina and it was a constitutive gene with low abundance in the wheat leaf tissue.The resistance homology sequence was successfully obtained,which provides the shortcut for cloning of the resistance gene in TcLr19 wheat.展开更多
In large loop transient electromagnetic method(TEM),the late time apparent resistivity formula cannot truly reflect the geoelectric model,thus it needs to define the all-time apparent resistivity with the position inf...In large loop transient electromagnetic method(TEM),the late time apparent resistivity formula cannot truly reflect the geoelectric model,thus it needs to define the all-time apparent resistivity with the position information of measuring point.Utilizing very fast simulated annealing(VFSA) to fit the theoretical electromagnetic force(EMF) and measured EMF could obtain the all-time apparent resistivity of the measuring points in rectangular transmitting loop.The selective cope of initial model of VFSA could be confirmed by taking the late time apparent resistivity of transient electromagnetic method as the prior information.For verifying the correctness,the all-time apparent resistivities of the geoelectric models were calculated by VFSA and dichotomy,respectively.The results indicate that the relative differences of apparent resistivities calculated by these two methods are within 3%.The change of measuring point position has little influence on the tracing pattern of all-time apparent resistivity.The first branch of the curve of all-time apparent resistivity is close to the resistivity of the first layer medium and the last branch is close to the resistivity of the last layer medium,which proves the correctness of the arithmetics proposed.展开更多
New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reacto...New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reactor. The pores blocking models were created based on the standard blocking law and the intermediate blocking law, and then the cake layer models were developed based on the hydrodynamic theory in which the calculation method of porosity of cake layer was newly corrected. The Air-Water-FCC equilibrium catalysts cold model experiment was used to verify the relevant models.Results showed that the calculated values fitted well with experimental data with a relative error of less than 10%.展开更多
Common bean is an important but often a disease-susceptible legume crop of temperate,subtropical and tropical regions worldwide. The crop is affected by bacterial, fungal and viral pathogens. The strategy of resistanc...Common bean is an important but often a disease-susceptible legume crop of temperate,subtropical and tropical regions worldwide. The crop is affected by bacterial, fungal and viral pathogens. The strategy of resistance-gene homologue(RGH) cloning has proven to be an efficient tool for identifying markers and R(resistance) genes associated with resistances to diseases. Microsatellite or SSR markers can be identified by physical association with RGH clones on large-insert DNA clones such as bacterial artificial chromosomes(BACs). Our objectives in this work were to identify RGH-SSR in a BAC library from the Andean genotype G19833 and to test and map any polymorphic markers to identify associations with known positions of disease resistance genes. We developed a set of specific probes designed for clades of common bean RGH genes and then identified positive BAC clones and developed microsatellites from BACs having SSR loci in their end sequences. A total of 629 new RGH-SSRs were identified and named BMr(bean microsatellite RGH-associated markers). A subset of these markers was screened for detecting polymorphism in the genetic mapping population DOR364 × G19833. A genetic map was constructed with a total of 264 markers,among which were 80 RGH loci anchored to single-copy RFLP and SSR markers. Clusters of RGH-SSRs were observed on most of the linkage groups of common bean and in positions associated with R-genes and QTL. The use of these new markers to select for disease resistance is discussed.展开更多
AIM: To review the defnition and performance of the commonly used end points in trials of systemic thera-pies in metastatic castration-resistant prostate cancer patients. METHODS: A literature search was undertaken...AIM: To review the defnition and performance of the commonly used end points in trials of systemic thera-pies in metastatic castration-resistant prostate cancer patients. METHODS: A literature search was undertaken on PubMed database to identify studies meeting estab-lished criteria, with the aim of selecting randomized clinical trials and study definition and performance of their end points. The end points were grouped into three categories: overall survival (OS), time-to-event end points, and response end points. A special analysis was performed for secondary end points of the studies which documented a beneft in OS in the experimental arm. Finally, publishes analyses for surrogacy of the in-cluded end points were also reported. RESULTS: OS, time-to-event and response end points in 31 selected trials were analyzed. OS was the pri-mary end point in 14 trials, and the secondary end point in 17. A time-to-event end point was the primaryend point in 8 studies, and the secondary end point in 22; the most reported time-to-event end points were composite end points, and the events changed among trials. A response end point was the primary end point in 9 studies, in 3 it was prostate-specifc antigen (PSA)-related, in 3 pain-related and in 3 mixed. A response end point was the secondary end point in 19 studies: PSA response and radiologic response were the most frequently used secondary end points in 19 and 11 tri-als, respectively, while pain response was used in 5 studies.CONCLUSION: A homogeneous defnition of progres-sion in future trials is mandatory. Among response end points, pain-response and PSA-response appear to be the most reliable.展开更多
<strong>Introduction:</strong><span><span><span style="font-family:""><span style="font-family:Verdana;"> The decision to stop anti-cancer treatment is frau...<strong>Introduction:</strong><span><span><span style="font-family:""><span style="font-family:Verdana;"> The decision to stop anti-cancer treatment is fraught with many challenges for the oncologist, the patient, and their caregivers. This review examines the special considerations surrounding the decision to cease chemotherapy in terminally ill cancer patient. </span><b><span style="font-family:Verdana;">Methods: </span></b><span style="font-family:Verdana;">A comprehensive literature search was conducted to find relevant publications on chemotherapy cessation. A total of 2700 records were retrieved and 141 were identified as eligible for inclusion in this review. </span><b><span style="font-family:Verdana;">Results: </span></b><span style="font-family:Verdana;">Palliative chemotherapy does not achieve the goal of tumor-related symptom reduction for patients who have experienced progressive disease with more than two prior lines of chemotherapy. ECOG performance status is a crucial predictor of response to therapy and chemotherapy-related complications. Challenges to stopping chemotherapy at the end of life are multifactorial and are both patient and physician-driven. Racial, ethnic, and income-based disparities are seen in the timing and quality of end-of-life conversations offered by physicians to their patients. </span><b><span style="font-family:Verdana;">Conclusions:</span></b><span style="font-family:Verdana;"> The decision to cease chemotherapy is one that should be approached with careful consideration and accurate information. Clear communication, compassion and empathy are important components to the therapeutic relationship. Early involvement of palliative care and clear conversations about prognosis and the expected utility of further chemotherapy is essential to conduct the best possible care for cancer patients at the end of life.</span></span></span></span>展开更多
文摘This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.
文摘Resistive Plate Chambers(RPCs) built from a new type of Bakelite developed at Institute of High Energy Physics(IHEP),Chinese Academy of Sciences have been used in the BESⅢ Muon identification system for several years without linseed oil coating,but characteristic aging performances were observed.To adapt to the RPCs in the aging state,the front-end electronics have been upgraded by enhancing the front-end protection,improving the threshold setting circuit,and separating power supplies of the comparator and the field programmable gate array(FPGA).Improvements in system stability,front-end protection and threshold consistency have been achieved.In this paper,the system upgrade and the test results are described in detail.
文摘The saving of non-renewable energies, as well as the reduction of emissions into the environment, are two crucial objectives of industrial production. The recovery of post-consumer products associated with the use of end-of-life products is part of a context of optimization of these objectives. This recovery maximizes the use of resources from end-of-life products in a circular logic while recording the environmental footprint. This study considers a recycling strategy adapted to the need and urgency to reduce greenhouse gas emissions caused by global warming. The proposed model aims to optimize the profits of the circular manufacturing strategies while minimizing operational costs (collection, sorting, recycling), transport, GHG emissions and recycling. In this paper, a compromise between the gains of CM and the costs associated with it was studied. The robustness of the designed model was tested using a case study based on real-world scenarios. A sensitivity analysis was carried out to study the impact of the emission cost on the overall objective, considering the two options currently offered to industries. The obtained results support companies to take the ecological aspect into account and integrate sustainable development into their strategic axes for their logistics supply chains.
基金Project(51078330) supported by the National Natural Science Foundation of ChinaProject(2012MS21339) supported by China Postdoctoral Science FoundationProject(2012GN012) supported by the Independent Innovation Foundation of Shandong University, China
文摘A series of well-designed full-scale destructive load tests were conducted on six bored piles to investigate the influence of loose debris at the pile tip on end resistance. The results show that soft debris below the pile tip will weaken the mobilization of end resistance. The ultimate tip resistance of post-grouted pile is 2.05 times that of the pile without post-grouting and the ultimate tip resistance in the second load cycle is 2.31 times that of pile in the first load cycle. The relationship between unit end resistance and displacement follows a linear model and a bilinear mode in the first load cycle and the second load cycle, respectively, whereas the unit end resistance-displacement response of post-grouted bored pile can be simulated using a bilinear mode. The critical end resistance ranges between 2 000 kN and 3 000 kN and the critical displacement ranges between 2.5 mm and 4.5 mm in the bilinear mode. As for piles rested on moderately-weathered peliticsiltstone, the socketed length has no effect on the end resistance because of the existence of loose debris.
基金This research was financially supported by the National Science Fund for Distinguished Young Scholars(Grant No.51825904)the National Science and Technology Major Project from the Ministry of Science and Technology(MOST)of China(Grant No.2016ZX05058004-005).
文摘Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.
文摘ITO (indium oxide doped with tin) thin films were deposited on glass substrates by using ITO pellet with a composition of w(In2O3)=90% and w(SnO2)=10% by electron beam evaporated with End-Hall ion source assisted without extra heating. The rate of deposition and flow rate of oxygen were measured and changed to obtain the best properties of ITO thin films. Furthermore, the post annealing process was done in vacuum at different annealing temperatures for 2 h and at 400℃ for different keeping time, respectively. The relation between optical, electrical properties and structure was discussed in detail.
文摘Spontaneous bacterial peritonitis(SBP) is the most common infection in end-stage liver disease patients.SBP is defined as an ascitic fluid infection with a polymorphonuclear leucocyte count ≥ 250/mm^3 without an evident intra-abdominal surgically treatable source.Several mechanisms contribute to SBP occurrence,including translocation of gut bacteria and their products,reduced intestinal motility provoking bacterial overgrowth,alteration of the gut's barrier function and local immune responses.Historically,Gram-negative enteric bacteria have been the main causative agents of SBP,thereby guiding the empirical therapeutic choice.However,over the last decade,a worryingly increasing prevalence of Gram-positive and multi-drug resistant(MDR) SBP has been seen.Recently,the microbiological spectrum of SBP seems to have changed in Europe due to a high prevalence of Gram-positive bacteria(48%-62%).The overall proportion of MDR bacteria is up to 22%-73% of cases.Consequently,empirical therapy based on thirdgeneration cephalosporins or amoxicillin/clavulanic acid,can no longer be considered the standard of care,as these drugs are associated with poor outcomes.Theaim of this review is to describe,with an epidemiological focus,the evidence behind this rise in Gram-positive and MDR SBP from 2000 to present,and illustrate potential targeted therapeutic strategies.An appropriate treatment protocol should include daptomycin plus ceftaroline and meropenem,with prompt stepdown to a narrower spectrum when cultures and sensitivity data are available in order to reduce both cost and potential antibiotic resistance development.
基金supported by grants from the National Natural Science Foundation of China(Grant Nos.:82003807,82173394)the Shaanxi Province Science Foundation,China(Grant No.:2023-GHZD-19)+1 种基金the Medical Foundation-Clinical Integration Program of Xi'an Jiaotong University,China(Grant No.:YXJLRH2022043)the Xi'an Jiaotong University Free Exploration and Innovation-Teacher Project Foundation,China(Grant No.:xzy012023104).
文摘Chemotherapy resistance plays a pivotal role in the prognosis and therapeutic failure of patients with colorectal cancer(CRC).Cisplatin(DDP)-resistant cells exhibit an inherent ability to evade the toxic chemotherapeutic drug effects which are characterized by the activation of slow-cycle programs and DNA repair.Among the elements that lead to DDP resistance,O^(6)-methylguanine(O^(6)-MG)-DNA-methyltransferase(MGMT),a DNA-repair enzyme,performs a quintessential role.In this study,we clarify the significant involvement of MGMT in conferring DDP resistance in CRC,elucidating the underlying mechanism of the regulatory actions of MGMT.A notable upregulation of MGMT in DDP-resistant cancer cells was found in our study,and MGMT repression amplifies the sensitivity of these cells to DDP treatment in vitro and in vivo.Conversely,in cancer cells,MGMT overexpression abolishes their sensitivity to DDP treatment.Mechanistically,the interaction between MGMT and cyclin dependent kinase 1(CDK1)inducing slow-cycling cells is attainted via the promotion of ubiquitination degradation of CDK1.Meanwhile,to achieve nonhomologous end joining,MGMT interacts with XRCC6 to resist chemotherapy drugs.Our transcriptome data from samples of 88 patients with CRC suggest that MGMT expression is co-related with the Wnt signaling pathway activation,and several Wnt inhibitors can repress drug-resistant cells.In summary,our results point out that MGMT is a potential therapeutic target and predictive marker of chemoresistance in CRC.
文摘With rapid development of the semiconductor technology, more efficient cooling systems for electronic devices are needed. In this situation, in the present study, a loop thermosyphon type cooling system, which is composed mainly of a heating block, an evaporator and an air-cooled condenser, is investigated experimentally in order to evaluate the cooling performance. At first, it is examined that the optimum volume filling rate of this cooling system is approximately 40%. Next, four kinds of working fluids, R1234ze(E), R1234ze(Z), R134a and ethanol, are tested using a blasted heat transfer surface of the evaporator. In cases of R1234ze(E), R1234ze(Z), R134a and ethanol, the effective heat flux, at which the heating block surface temperature reaches 70°C, is 116 W/cm2, 106 W/cm2, 104 W/cm2 and 60 W/cm2, respectively. This result indicates that R1234ze(E) is the most suitable for the present cooling system. The minimum boiling thermal resistance of R1234ze(E) is 0.05 (cm2·K)/W around the effective heat flux of 100 W/cm2. Finally, four kinds of heat transfer surfaces of the evaporator, smooth, blasted, copper-plated and finned surfaces, are tested using R1234ze(E) as working fluid. The boiling thermal resistance of the blasted surface is the smallest among tested heat transfer surfaces up to 116 W/cm2 in effective heat flux. However, it increases drastically due to the appearance of dry-patch if the effective heat flux exceeds 116 W/cm2. On the other hand, in cases of copper-plated and finned surfaces, the dry-patch does not appear up to 150 W/cm2 in effective heat flux, and the boiling thermal resistances of those surfaces keep 0.1 (cm2·K)/W.
文摘This paper presents an analysis of the effect of parasitic resistances on the performance of DC-DC Single Ended Pri- mary Inductor Converter (SEPIC) in photovoltaic maximum power point tracking (MPPT) applications. The energy storage elements incorporated in the SEPIC converter possess parasitic resistances. Although ideal components significantly simplifies model development, but neglecting the parasitic effects in models may sometimes lead to failure in predicting first scale stability and actual performance. Therefore, the effects of parasitics have been taken into consideration for improving the model accuracy, stability, robustness and dynamic performance analysis of the converter. Detail mathematical model of SEPIC converter including inductive parasitic has been developed. The performance of the converter in tracking MPP at different irradiance levels has been analyzed for variation in parasitic resistance. The converter efficiency has been found above 83% for insolation level of 600 W/m2 when the parasitic resistance in the energy storage element has been ignored. However, as the parasitic resistance of both of the inductor has increased to 1 ohm, a fraction of the power managed by the converter has dissipated;as a result the efficiency of the converter has reduced to 78% for the same insolation profile. Although the increasing value of the parasitic has assisted the converter to converge quickly to reach the maximum power point. Furthermore it has also been observed that the peak to peak load current ripple is reduced. The obtained simulation results have validated the competent of the MPPT converter model.
文摘Adeno-associated virus(AAV) is a single-stranded linear defective parvovirus. Using the model proposed by Cavalier-Smith for replication of ss-DNA virus. the linear fragment of inverted terminal repeats(ITRs) from PAAV/neo was isolated, denatured and refolded over. The daughter DNA was synthesized by using 3'-OH terminus as a primer with the new strand covalently linked to the parental strand. After the palindromic structure with neomycin resistance gene controlled by SV40 early promoter into eukaryotic cells. Southern blot showed that the molecule of hairpin structure could facilitate the copies into mammalian cells in vitro. The experiment supports the Cavalier-Smith's replication model of ss-DNA virus and provides another new system for DNA transduction.
基金funded by the National Natural Science Foundation of China (30771391,30700505)the Natural Science Foundation of Hebei Province,China (C2008000281)
文摘One resistance gene analog fragment named RGA-CIN14 was isolated from TcLr19 wheat,which contains kinase-2,kinase-3a,and the GLPL motif of the NBS-spanning region,using degenerated primers according to the nucleotide binding site (NBS) conserved domain.Based on the RGA-CIN14,a full-length cDNA,CIN14,which was 2 987 bp encoding 880 amino acids,was obtained by using the method of the rapid amplification cDNA ends (RACE).Bioinformatics analysis showed that the deduced amino acids of CIN14 protein consisted of a NB-ARC conserved domain and many leucine-rich repeats (LRR) domains.The phylogenetic tree analysis indicated a considerable identity of the protein encoded by CIN14 with that of wheat leaf rust resistance gene Lr1,but a lower similarity with Lr21.The expression profile of the CIN14 gene detected by semi-quantitative RT-PCR showed that the CIN14 gene was not induced by Puccinia triticina and it was a constitutive gene with low abundance in the wheat leaf tissue.The resistance homology sequence was successfully obtained,which provides the shortcut for cloning of the resistance gene in TcLr19 wheat.
基金Projects(40804027,41074085) supported by the National Natural Science Foundation of ChinaProject(09JJ3048) supported by the Natural Science Foundation of Hunan Province,ChinaProject(200805331082) supported by the Research Fund for the Doctoral Program of Higher Education,China
文摘In large loop transient electromagnetic method(TEM),the late time apparent resistivity formula cannot truly reflect the geoelectric model,thus it needs to define the all-time apparent resistivity with the position information of measuring point.Utilizing very fast simulated annealing(VFSA) to fit the theoretical electromagnetic force(EMF) and measured EMF could obtain the all-time apparent resistivity of the measuring points in rectangular transmitting loop.The selective cope of initial model of VFSA could be confirmed by taking the late time apparent resistivity of transient electromagnetic method as the prior information.For verifying the correctness,the all-time apparent resistivities of the geoelectric models were calculated by VFSA and dichotomy,respectively.The results indicate that the relative differences of apparent resistivities calculated by these two methods are within 3%.The change of measuring point position has little influence on the tracing pattern of all-time apparent resistivity.The first branch of the curve of all-time apparent resistivity is close to the resistivity of the first layer medium and the last branch is close to the resistivity of the last layer medium,which proves the correctness of the arithmetics proposed.
基金financially supported by the National Key Research & Development Program of China (2016YFB0301600)
文摘New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reactor. The pores blocking models were created based on the standard blocking law and the intermediate blocking law, and then the cake layer models were developed based on the hydrodynamic theory in which the calculation method of porosity of cake layer was newly corrected. The Air-Water-FCC equilibrium catalysts cold model experiment was used to verify the relevant models.Results showed that the calculated values fitted well with experimental data with a relative error of less than 10%.
文摘Common bean is an important but often a disease-susceptible legume crop of temperate,subtropical and tropical regions worldwide. The crop is affected by bacterial, fungal and viral pathogens. The strategy of resistance-gene homologue(RGH) cloning has proven to be an efficient tool for identifying markers and R(resistance) genes associated with resistances to diseases. Microsatellite or SSR markers can be identified by physical association with RGH clones on large-insert DNA clones such as bacterial artificial chromosomes(BACs). Our objectives in this work were to identify RGH-SSR in a BAC library from the Andean genotype G19833 and to test and map any polymorphic markers to identify associations with known positions of disease resistance genes. We developed a set of specific probes designed for clades of common bean RGH genes and then identified positive BAC clones and developed microsatellites from BACs having SSR loci in their end sequences. A total of 629 new RGH-SSRs were identified and named BMr(bean microsatellite RGH-associated markers). A subset of these markers was screened for detecting polymorphism in the genetic mapping population DOR364 × G19833. A genetic map was constructed with a total of 264 markers,among which were 80 RGH loci anchored to single-copy RFLP and SSR markers. Clusters of RGH-SSRs were observed on most of the linkage groups of common bean and in positions associated with R-genes and QTL. The use of these new markers to select for disease resistance is discussed.
文摘AIM: To review the defnition and performance of the commonly used end points in trials of systemic thera-pies in metastatic castration-resistant prostate cancer patients. METHODS: A literature search was undertaken on PubMed database to identify studies meeting estab-lished criteria, with the aim of selecting randomized clinical trials and study definition and performance of their end points. The end points were grouped into three categories: overall survival (OS), time-to-event end points, and response end points. A special analysis was performed for secondary end points of the studies which documented a beneft in OS in the experimental arm. Finally, publishes analyses for surrogacy of the in-cluded end points were also reported. RESULTS: OS, time-to-event and response end points in 31 selected trials were analyzed. OS was the pri-mary end point in 14 trials, and the secondary end point in 17. A time-to-event end point was the primaryend point in 8 studies, and the secondary end point in 22; the most reported time-to-event end points were composite end points, and the events changed among trials. A response end point was the primary end point in 9 studies, in 3 it was prostate-specifc antigen (PSA)-related, in 3 pain-related and in 3 mixed. A response end point was the secondary end point in 19 studies: PSA response and radiologic response were the most frequently used secondary end points in 19 and 11 tri-als, respectively, while pain response was used in 5 studies.CONCLUSION: A homogeneous defnition of progres-sion in future trials is mandatory. Among response end points, pain-response and PSA-response appear to be the most reliable.
文摘<strong>Introduction:</strong><span><span><span style="font-family:""><span style="font-family:Verdana;"> The decision to stop anti-cancer treatment is fraught with many challenges for the oncologist, the patient, and their caregivers. This review examines the special considerations surrounding the decision to cease chemotherapy in terminally ill cancer patient. </span><b><span style="font-family:Verdana;">Methods: </span></b><span style="font-family:Verdana;">A comprehensive literature search was conducted to find relevant publications on chemotherapy cessation. A total of 2700 records were retrieved and 141 were identified as eligible for inclusion in this review. </span><b><span style="font-family:Verdana;">Results: </span></b><span style="font-family:Verdana;">Palliative chemotherapy does not achieve the goal of tumor-related symptom reduction for patients who have experienced progressive disease with more than two prior lines of chemotherapy. ECOG performance status is a crucial predictor of response to therapy and chemotherapy-related complications. Challenges to stopping chemotherapy at the end of life are multifactorial and are both patient and physician-driven. Racial, ethnic, and income-based disparities are seen in the timing and quality of end-of-life conversations offered by physicians to their patients. </span><b><span style="font-family:Verdana;">Conclusions:</span></b><span style="font-family:Verdana;"> The decision to cease chemotherapy is one that should be approached with careful consideration and accurate information. Clear communication, compassion and empathy are important components to the therapeutic relationship. Early involvement of palliative care and clear conversations about prognosis and the expected utility of further chemotherapy is essential to conduct the best possible care for cancer patients at the end of life.</span></span></span></span>