Thermo-hydro-poro-mechanical responses of a reservoir-induced landslide tracked by high-resolution fiber optic sensing nerves

Thermo-poro-mechanical responses along sliding zone/surface have been extensively studied.However,it has not been recognized that the potential contribution of other crucial engineering geological interfaces beyond the slip surface to progressive failure.Here,we aim to investigate the subsurface multiphysics of reservoir landslides under two extreme hydrologic conditions(i.e.wet and dry),particularly within sliding masses.Based on ultra-weak fiber Bragg grating(UWFBG)technology,we employ specialpurpose fiber optic sensing cables that can be implanted into boreholes as“nerves of the Earth”to collect data on soil temperature,water content,pore water pressure,and strain.The Xinpu landslide in the middle reach of the Three Gorges Reservoir Area in China was selected as a case study to establish a paradigm for in situ thermo-hydro-poro-mechanical monitoring.These UWFBG-based sensing cables were vertically buried in a 31 m-deep borehole at the foot of the landslide,with a resolution of 1 m except for the pressure sensor.We reported field measurements covering the period 2021 and 2022 and produced the spatiotemporal profiles throughout the borehole.Results show that wet years are more likely to motivate landslide motions than dry years.The annual thermally active layer of the landslide has a critical depth of roughly 9 m and might move downward in warmer years.The dynamic groundwater table is located at depths of 9e15 m,where the peaked strain undergoes a periodical response of leap and withdrawal to annual hydrometeorological cycles.These interface behaviors may support the interpretation of the contribution of reservoir regulation to slope stability,allowing us to correlate them to local damage events and potential global destabilization.This paper also offers a natural framework for interpreting thermo-hydro-poro-mechanical signatures from creeping reservoir bank slopes,which may form the basis for a landslide monitoring and early warning system.

Influence of Sugarcane Bagasse Fibers on the Mechanical Strength and Porosity of Concrete Made with Forspak 42.5 N Cement in the Republic of Congo

The concrete mixed to sugarcane bagasse fibers and polypropylene fibers prepared with varied conditions were presented. The aim of our study is to formulate a concrete mixed with sugarcane bagasse fibers, which will gradually replace the conventional polypropylene fibers often used. We formulated all our concretes using the dreux gorisse method. We used an oven calibrated at 105˚C to dry the washed fibers. We also carried out tensile splitting and compression tests, at 28 and 112 days of age. The reinforcement mechanisms of sugarcane bagasse fibers and polypropylene fibers concretes were subjected to tensile splitting and compression tests after total immersion of the specimens in tap water at 28 and 112 days. Porosity at 28 days, mass loss and drying shrinkage at 80 days were also studied. The curing processes of concretes containing 0.10, 0.15, 0.17, 0.23 and 0.25% bagasse fibers were compared with those of ordinary concretes containing no fiber. The results showed that the addition of bagasse fibers reduces mechanical strength and porosity. In summary, specimens SBC-0.15 and SBC-0.17 showed the best results for all fibers. We plan to do the same work, but this time with raffia or palm nut fibers.

Polyetherketoneketone/carbon fiber composites with an amorphous interface prepared by solution impregnation

Interfacial adhesion between carbon fibers(CF)and polyetherketoneketone(PEKK)is a key factor that affects the mechanical performances of their composites.It is therefore of great importance to impregnate the CF bundles with PEKK as effi-ciently as possible.We report that PEKK with a good dispersion in a mixed solution of 4-chlorophenol and 1,2-dichloroethane can be introduced onto CF surfaces by solution impregnation and curing at 280,320,340 and 360℃.The excellent wettability or infiltra-tion of the PEKK solution guarantees a full covering and its tight binding to CFs,making it possible to evaluate the interfacial shear strength(IFSS)with the microdroplet method.The interior of the CF bundles is completely and uniformly filled with PEKK by solu-tion impregnation,leading to a high interlaminar shear strength(ILSS).The maximum IFSS and ILSS reached 107.8 and 99.3 MPa,respectively.Such superior shear properties are ascribed to the formation of amorphous PEKK in the small spaces between CFs.

The DUF579 proteins GhIRX15s regulate cotton fiber development by interacting with proteins involved in xylan synthesis

Cotton provides the most abundant natural fiber for the textile industry.The mature cotton fiber largely consists of secondary cell walls with the highest proportion of cellulose and a small amount of hemicellulose and lignin.To dissect the roles of hemicellulosic polysaccharides during fiber development,four IRREGULAR XYLEM 15(IRX15)genes,GhIRX15-1/-2/-3/-4,were functionally characterized in cotton.These genes encode DUF579 domain-containing proteins,which are homologs of AtIRX15 involved in xylan biosynthesis.The four GhIRX15 genes were predominantly expressed during fiber secondary wall thickening,and the encoded proteins were localized to the Golgi apparatus.Each GhIRX15 gene could restore the xylan deficient phenotype in the Arabidopsis irx15irx15l double mutant.Silencing of GhIRX15s in cotton resulted in shorter mature fibers with a thinner cell wall and reduced cellulose content as compared to the wild type.Intriguingly,GhIRX15-2 and GhIRX15-4 formed homodimers and heterodimers.In addition,the GhIRX15s showed physical interaction with glycosyltransferases GhGT43C,GhGT47A and GhGT47B,which are responsible for synthesis of the xylan backbone and reducing end sequence.Moreover,the GhIRX15s can form heterocomplexes with enzymes involved in xylan modification and side chain synthesis,such as GhGUX1/2,GhGXM1/2 and GhTBL1.These findings suggest that GhIRX15s participate in fiber xylan biosynthesis and modulate fiber development via forming large multiprotein complexes.

Carrageenan Fiber Prepared by a New Process Route of Ba^(2+)Ion Pre-Crosslinking in the Spinning Solution

Ba^(2+)pre-crosslinked carrageenan fiber(Ba/CAF)was prepared by adding a small amount of Ba^(2+) to the carrageenan(CA)solution as the spinning solution.Ba/CAF-n/A,Ba/CAF-n/B and Ba/CAF-n/C were prepared with ethanol solution(combine A),high concentration BaCl_(2)solution(combine B)and low concentration BaCl_(2)solution(combine C),as coagulation bath and stretch bath,respectively.The combination of coagulation bath and stretch bath suitable for Ba^(2+) pre-crosslinking wet spinning was screened.The results showed that Ba^(2+) can induce the birefringence of the CA molecular chain,and the Ba^(2+) pre-crosslinking effect is the best when the CA mass fraction is 8.0 wt%.From the perspective of production safety,fiber performance and spinning cost,the coagulation bath of 3.5 wt%BaCl_(2)solution and stretch bath of 1.7 wt%BaCl_(2)solution,that is,combination C with low concentration BaCl_(2)solution,is the best choice.Ba/CAF-8.0/C was obtained under the best conditions.The linear intensity,water absorption and flame retardancy study showed that the breaking strength of Ba/CAF-8.0/C is as high as 1.61 cN/dtex,the water absorption was 649.2%and 574.3%,in deionized water and normal saline,respectively,and the LOI value reached 32.

Research on the Development of Fibroin and Nano-Fiber from Silk Cocoons for Regenerated Tissue Engineering Applications by Electro-Spinning

In this paper, the main goal is to prepare silk fibroin nano-fiber, which is used for regenerated tissue applications. Silk scaffold nano-fibers made by electro-spinning technology can be used in regenerated tissue applications. The purpose of the research is to prepare a silk-fibroin nano-fiber solution for potential applications in tissue engineering. Using a degumming process, pure silk fibroin protein is extracted from silk cocoons. The protein solution for fibroin is purified, and the protein content is determined. The precise chemical composition, exact temperature, time, voltage, distance, ratio, and humidity all have a huge impact on degumming, solubility, and electro-spinning nano-fibers. The SEM investigates the morphology of silk fibroin nano-fibres at different magnifications. It also reveals the surface condition, fiber orientation, and fiber thickness of the silk fibroin nano-fiber. The results show that regenerated silk fibroin and nano-fiber can be used in silk fibroin scaffolds for various tissue engineering applications.

Theoretical Modeling for Predicting the Optimum Twist Angle of Cotton Fiber Movement on OE Yarn Made by Rotor Spinning Machine

This paper presents theoretical modeling for predicting the optimum twist angle on yarn made by open end rotor spinning machine in textile industry. Fiber movement on yarn can be used for predicting the optimum twist angle which can be used to reduce yarn breaking in spinning process. In this research the twist angle has been found and the result of this research shows the twist angle around 45°;and the theoretical result of the ratio of rotor diameter to fiber length is .

Genome-wide identification of the pectate lyase(PEL)gene family members in Malvaceae,and their contribution to cotton fiber quality

Pectin is a major constituent of the plant cell wall.Pectate lyase(PEL,EC 4.2.2.2)uses anti-β-elimination chemistry to cleave theα-1,4 glycosidic linkage in the homogalacturonan region of pectin.However,limited information is available on the comprehensive and evolutionary analysis of PELs in the Malvaceae.In this study,we identified 597PEL genes from 10 Malvaceae species.Phylogenetic and motif analyses revealed that these PELs are classified into six subfamilies:Clades I,II,III,IV,Va,and Vb.The two largest subfamilies,Clades I and II,contained 237 and222 PEL members,respectively.The members of Clades Va and Vb only contained four or five motifs,far fewer than the other subfamilies.Gene duplication analysis showed that segmental duplication played a crucial role in the expansion of the PEL gene family in Gossypium species.The PELs from Clades I,IV,Va,and Vb were expressed during the fiber elongation stage,but nearly all PEL genes from Clades II and III showed no expression in any of the investigated fiber developmental stages.We further performed single-gene haplotype association analysis in 2,001G.hirsutum accessions and 229 G.barbadense accessions.Interestingly,14 PELs were significantly associated with fiber length and strength traits in G.barbadense with superior fiber quality,while only eight GhPEL genes were found to be significantly associated with fiber quality traits in G.hirsutum.Our findings provide important information for further evolutionary and functional research on the PEL gene family members and their potential use for fiber quality improvement in cotton.

Microwave thermal remediation of crude oil contaminated soil enhanced by carbon fiber

Thermal remediation of the soil contaminated with crude oil using microwave heating enhanced by carbon fiber （CF） was explored. The contaminated soil was treated with 2.45 GHz microwave, and CF was added to improve the conversion of microwave energy into thermal energy to heat the soil. During microwave heating, the oil contaminant was removed from the soil matrix and recovered by a condensation system of ice-salt bath. The experimental results indicated that CF could efficiently enhance the microwave heating of soil even with relatively low-dose. With 0.1 wt.% CF, the soil could be heated to approximately 700℃ within 4 min using 800 W of microwave irradiation. Correspondingly, the contaminated soil could be highly cleaned up in a short time. Investigation of oil recovery showed that, during the remediation process, oil contaminant in the soil could be efficiently recovered without causing significant secondary pollution.

Thermal Properties of Crosslinking Modified Ultrahigh Molecular Weight Polyethylene Fibers by Ultra-Violet Irradiation

By means of ultra-violet(UV)irradiation with photoini-tiator and multifunctional crosslinking agent,thecrosslinking modification of ultrahigh molecular weightpolyethylene(UHMWPE)fibers prepared by gel-spin-ning was carried out.Thermal properties of fiber sampleswere examined using differential scanning calorimetry(DSC),thermomechanical analysis(TMA)apparatusand a manual device.The results indicated that the opti-mal irradiation energy is 250-400 mJ/cm^2,heat-andcreep-resistant behaviors of modified fibers have beenimproved.

Modification of Activated Carbon Fiber by Loading Metals and Their Performance on SO2 Removal

Metal-loaded activated carbon fibers （ACFs） were prepared by impregnation and characterized by N2 adsorption at 77K, XRD, XPS and SEM. Their properties on SO2 removal were examined in a tubular fixed bed reactor with a model flue gas. Cobalt-loaded ACF showed the best activity among the prepared metal-loaded ACFs and a constant removal ratio of SO2 above 87% during continuous exposure to the flow of SO2/O2/H2O/N2 at 45℃ for more than 216h. The characteristic of the prepared loaded-ACFs showed that the exceptional activity of Co-ACF was attributed to the high amount of active sites due to modification by loading cobalt.

Effect of Co-polyester antistatic agent modified by carbon nanotubes on the properties of polypropylene fibers

Antistatic polymer fibers were investigated by using carbon nanotubes （CNTs） to enhance the antistatic ability of inner antistatic agents based on the mechanism of attracting moisture by polar radical groups. It is indicated that the antistatic ability of the fibers filled with composite antistatic agents that contain CNTs and organic antistatic agents was superior to that of the fibers filled either with pure organic antistatic agents or pure CNTs. The antistatic ability of the composite antistatic agent fabricated by an in situ process was superior to that of the composite antistatic agent fabricated by direct dispersing CNTs in the antistatic agent carrier. Moreover, the heat-treated CNTs could further enhance the antistatic effect compared with the initial CNTs. The antistatic effect is significantly influenced by the content of CNTs in the composite antistatic agent.

Characterization of Cellulosic Fibers by FTIR Spectroscopy for Their Further Implementation to Building Materials

Nowadays, the material recycling is a growing trend in development of building materials and therefore using of secondary raw materials for production new building materials is in accordance with sustainable development in civil engineering. Therefore, it is increasingly becoming crucial to accelerate the transition from application of non-renewable sources of raw materials to renewable raw materials. One fast renewable resource is natural plant fibers. The use of the cellulosic fibers as environmentally friendly material in building products contributes to the environmental protection and saves non-renewable resources of raw materials. Wood fibers and recycled cellulose fibers of waste paper appear as suited reinforcing elements for cement-based materials. In this paper, there is used application of Fourier transform infrared spectroscopy (FTIR) on cellulose fibers coming from different sources. FTIR spectra of cellulose fiber samples are investigated and compared with reference sample of cellulose.

A Study on the Surface Structures of Viscose-based Activated Carbon Fiber by FT-IR Spectroscopy and XPS

Using viscose fiber (VF) as starting material and common steam as activating agent, formation of oxygen structures in activated carbon fiber is investigated. In the preparation of samples, VF was first heated at temperatures between 450℃ and 900℃ in N_2 artmosphere. Then, in a successive activation stage, the product carbonized at 600℃ was activated in steam at 450-900℃ for 30 min, and at 600℃ for 5-30 min. The other carbonization products were activated at 600 and 900℃ for 30 min respectively. The products activated at 900℃ were then activated at 450℃ for 30 min again. The starting materiah carbonized products and all activation products were examined by FT-IR spectroscopy and some products were examined by X-ray photoelectron spectroscope (XPS). And the yields of the carbonized and activated products were calculated. By analysing these spectra, the amount of oxygen-containing functional groups of the activated products attained under various activation time, various activation temperature and various previous carbonization temperature was determined.

Gas-initiation under UV and liquid-grafting polymerization on the surface of polysulfone hollow fiber ultrafiltration membrane by dynamic method

Using the inner-surface of polysulfone hollow fiber ultrafiltration membranes as grafted layer, the method of gas-initiation and liquid-polymerization has been studied, which aimed to adjust the diameter of the pores in the membranes. The degree of polymerization varied with the changes of the parameters, such as irradiation time, monomer concentration, temperature and time of polymerization and so on. The results indicated that using benzophenone(BP) which is in a gaseous condition as photo-initiator, acrylamide as graft monomer, the polyacrylamide chain was grafted on the surface of membranes. After the surface membrane being modified, the water flux and retention altered,and thus it can be seen that the diameter of the pores in the membrane was altered. These experiments contribute to finding a new way to produce the hollow fiber membrane with the small pore size and are extraordinarily worth developing and studying.

Controllable large-scale processing of temperature regulating sheath-core fibers with high-enthalpy for thermal management

Temperature regulating fibers(TRF_(s)) with high enthalpy and high form stability are the key factors for thermal management. However, the enthalpies of most TRFsare not high, and the preparation methods are still at the laboratory scale. It remains a great challenge to use industrial spinning equipment to achieve continuous processing of TRF_(s) with excellent thermal and mechanical properties. Here, polyamide 6(PA6) based TRF_(s) with a sheath-core structure were prepared by bicomponent melt-spinning. The sheath-core TRF(TRF_(sc)) are composed of PA6 as sheath and functional PA6 as core, which are filled with the shape stable phase change materials(ssPCM),dendritic silica@polyethylene glycol(SiO_(2)@PEG). With the aid of the sheath structure, the filling content of SiO_(2)@PEG can reach 30 %, so that the enthalpy of the TRF_(s) can be as high as 21.3 J/g. The ultra-high enthalpy guarantees the temperature regulation ability during the alternating process of cooling and heating. In hot environment, the temperature regulation time is 6.59 min, and the temperature difference is 12.93℃. In addition, the mechanical strength of the prepared TRF_(sc) reaches 2.26 cN/dtex, which can fully meet its application in the field of thermal management textiles and devices to manage the temperature regulation of the human body or precision equipment, etc.

THE PHYSICAL SIMULATION ON EXTRUSION PROCESS OF GLASS FIBER COMPOSITE WIRE COATED BY LEAD

The method of manufacturing the composite wire by extruding lead to coated glass fiber is described. The different composite wire that diameter is from 0.5 to 1.0mm has been produced by two kinds of different extruding technology (getting wire along horizontal direction and getting wire along perpendicular direction). The optimal extruding techno- logical parameter has been given in different extruding technology by the physical simulation (H: 300℃, 550kN, 0.16mm. P: 300℃, 215kN, 0.16mm). The effect on the coating speed by other extruding technological parameters in the different extruding technology has been discussed. The extruding temperature and extruding force is higher, the coating speed is faster. It has been pointed, that the affection on the extruding technology by the extruding temperature has also behaved as the extruding temperature rising up spontaneously. The reason for exiting the minimum extruding force and maximum extruding force also has been discussion in this paper. It is also important to the extruding process and coating speed that is the coating clearance.

Genetic improvement of fiber quality in tetraploid cotton:an overview of major QTLs and genes involved in and edited for the quality of cotton fibers

Cotton,an important industrial crop cultivated in more than 70 countries,plays a major role in the livelihood of millions of farmers and industrialists.Cotton is mainly grown for its fiber,an economic component that can be differentiated from its epidermal cells in the outer integument of a developing seed.Fiber length,fiber strength,and fiber fineness are three main attributes that contribute to the quality of cotton fibers.Recent advancements in genomics have identified key genes,which are the most important factors that govern these three traits,can be introduced into cultivars of interest via gene editing,marker-assisted selection,and transgenics,thus the narrow genetic background of cotton can be addressed and its fiber quality traits can be enhanced.Over the past two decades,quantitative trait loci(QTLs)have been mapped for different fiber traits,approximately 1850 QTLs have been mapped for fiber length,fiber strength,and fineness among which a few genes have been edited for quality improvement in cotton.In this background,the current review covers the development and the factors that influence these traits,along with the reported genes,QTLs,and the edited genomes for trait improvement.

Solitons and Their Biperiodic Pulsation in Ultrafast Fiber Lasers Based on CB/GO

The carbon black(CB)is introduced to manufacture CB/graphene oxide(GO)composite material to mitigate limitations of GO as a saturable absorber with the excellent performance in ultrafast fiber lasers.At a central wavelength of 1555.5 nm,the stable mode-locked pulse with width of 656 fs,repetition rate of 20.16 MHz,and high signal-to-noise ratio of 82.07 dB is experimentally obtained.Additionally,experimental observations for pulsation phenomena of vector biperiodic solitons combining period-1 and period-17,period-2 and period-32,period-3 and period-36 are verified via simulations.

Morphological, mechanical and thermal properties of cyanate ester/benzoxazine resin composites reinforced by silane treated natural hemp fibers

This present study deals with the reinforcement of thermosetting resin blends composed of cyanate ester(CE) and benzoxazine(BOZ) resins with natural hemp fibers(NHFs). These NHFs were initially treated by using a silane coupling agent(SCA) in order to chiefly enhance their distributions as well as adhesions within the CE/BOZ resin matrix,then incorporated with various weight amounts ranging from 5 wt% to 20 wt% with a regular interval of 5 wt%. The obtained results showed that at the maximum treated fiber loading(20 wt%), distinctive enhancements in the mechanical properties in terms of flexural strength and microhardness were obtained. Besides, the thermal stability and glass transition temperature(Tg) were appreciably enhanced and were higher than those of the pure CE/BOZ resin properties. With respect to the astonishing properties of the NHFs, these enhancements could be possibly due to the good dispersion and adhesion of the treated NHFs inside the CE/BOZ resin achieved upon using the SCA. Therefore,we believe herein that these renewable and cheap NHFs have considerable potential to be used as reinfocer materials for CE/BOZ resin composites to be used in various industrial sectors.