To clarify the formation and distribution of feldspar dissolution pores and predict the distribution of high-quality reservoir in gravity flow sandstone of the 7^(th) member of Triassic Yanchang Formation(Chang 7 Memb...To clarify the formation and distribution of feldspar dissolution pores and predict the distribution of high-quality reservoir in gravity flow sandstone of the 7^(th) member of Triassic Yanchang Formation(Chang 7 Member)in the Ordos Basin,thin sections,scanning electron microscopy,energy spectrum analysis,X-ray diffraction whole rock analysis,and dissolution experiments are employed in this study to investigate the characteristics and control factors of feldspar dissolution pores.The results show that:(1)Three types of diagenetic processes are observed in the feldspar of Chang 7 sandstone in the study area:secondary overgrowth of feldspar,replacement by clay and calcite,and dissolution of detrital feldspar.(2)The feldspar dissolution of Chang 7 tight sandstone is caused by organic acid,and is further affected by the type of feldspar,the degree of early feldspar alteration,and the buffering effect of mica debris on organic acid.(3)Feldspars have varying degrees of dissolution.Potassium feldspar is more susceptible to dissolution than plagioclase.Among potassium feldspar,orthoclase is more soluble than microcline,and unaltered feldspar is more soluble than early kaolinized or sericitized feldspar.(4)The dissolution experiment demonstrated that the presence of mica can hinder the dissolution of feldspar.Mica of the same mass has a significantly stronger capacity to consume organic acids than feldspar.(5)Dissolution pores in feldspar of Chang 7 Member are more abundant in areas with low mica content,and they improve the reservoir physical properties,while in areas with high mica content,the number of feldspar dissolution pores decreases significantly.展开更多
The mineralogical development and diagenetic sequence of lacustrine shales in the Chang 7 Member of the Yanchang Formation in the Ordos Basin are detailed studied.A model of their depositional system and a diagenetic ...The mineralogical development and diagenetic sequence of lacustrine shales in the Chang 7 Member of the Yanchang Formation in the Ordos Basin are detailed studied.A model of their depositional system and a diagenetic diagram are proposed in this study.Through detailed petrographic,mineralogical,and elemental analyses,four distinct shale types are identified:argillaceous shale,siliceous shale,calcareous shale,and carbonate,clay,and silt-bearing shale.The main diagenetic process in argillaceous shale is the transformation of illite to smectite,negatively impacting shale porosity.Siliceous shale undergoes carbonate cementation and quartz dissolution,contributing to increased porosity,particularly in mesopores.Calcareous shale experiences diagenesis characterised by carbonate formation and dissolution,with a prevalence of siderite.In carbonate,clay,and silt-bearing shale,the dissolution of K-feldspar contributes to illitization of kaolinite.Argillaceous shale,characterised by more clay minerals and lower mesopore volume,is identified as a potential hydrocarbon seal.Siliceous shale,with the highest pore volume and abundant inter-mineral pores,emerges as a promising shale oil reservoir.These findings contribute to a comprehensive understanding of shale properties,aiding in the prediction of shale oil exploration potential in the studied area.展开更多
Pure shales in the first member of Qingshankou Formation(simplified as Qing 1 Member)in the southern Songliao Basin,i.e.,the semi-deep and deep lacustrine shales,are characterized by a high content of clay minerals an...Pure shales in the first member of Qingshankou Formation(simplified as Qing 1 Member)in the southern Songliao Basin,i.e.,the semi-deep and deep lacustrine shales,are characterized by a high content of clay minerals and poor hydrocarbon mobility,making the development of shale oil difficult.According to the drilling and testing results,the shale of Qing 1 Member can be classified into 3 lithofacies,i.e.,bedded argillaceous shale,laminated diamictite shale,and interbedded felsic shale.The TOC and brittle minerals control the enrichment of shale oil,of them,TOC controls the total oil content,in other words,the total oil content increases with the increase of TOC;while the laminae made up of brittle minerals contain a large number of bigger intergranular pores which are favorable enrichment space for movable shale oil.In consideration of the origins of the 3 lithofacies,two shale oil enrichment models are classified,i.e.,the deep lacustrine high-TOC bedded argillaceous shale(Model-I)and the semi-deep lacustrine moderate-high-TOC laminated diamictite shale(Model-II).In the Model-I,the shale is characterized by high hydrocarbon generation ability,high total oil content,abundant horizontal bedding fractures,and vertical and high angle fractures locally;the complex fracture network formed by horizontal bedding fractures and vertical fractures improve the storage capacity and permeability of the shale reservoir,increase the enrichment space for movable oil.In the Model-II,the shale is characterized by good hydrocarbon generation ability and fairly high total oil content,and as the brittle laminae contain large intergranular pores,the shale has a higher movable oil content.Based on the two models,shale oil sweet-spot areas of 2880 km2 in the southern Songliao Basin are favorable for further exploration.Aimed at the difficulties in reservoir fracturing of the lacustrine shale with a high content of clay minerals,the composite fracturing technology with supercritical carbon dioxide was used in the shale oil reservoir for the first time,realizing large-scale volume fracturing in shale with a high content of clay minerals and strong heterogeneity,marking a breakthrough of oil exploration in continental shale with a high content of clay minerals in China.展开更多
There are abundant coal and coalbed methane(CBM)resources in the Xishanyao Formation in the western region of the southern Junggar Basin,and the prospects for CBM exploration and development are promising.To promote t...There are abundant coal and coalbed methane(CBM)resources in the Xishanyao Formation in the western region of the southern Junggar Basin,and the prospects for CBM exploration and development are promising.To promote the exploration and development of the CBM resources of the Xishanyao Formation in this area,we studied previous coalfield survey data and CBM geological exploration data.Then,we analyzed the relationships between the gas content and methane concentration vs.coal seam thickness,burial depth,coal reservoir physical characteristics,hydrogeological conditions,and roof and floor lithology.In addition,we briefly discuss the main factors influencing CBM accumulation.First,we found that the coal strata of the Xishanyao Formation in the study area are relatively simple in structure,and the coal seam has a large thickness and burial depth,as well as moderately good roof and floor conditions.The hydrogeological conditions and coal reservoir physical characteristics are also conducive to the enrichment and a high yield of CBM.We believe that the preservation of CBM resources in the study area is mainly controlled by the structure,burial depth,and hydrogeological conditions.Furthermore,on the basis of the above results,the coal seam of the Xishanyao Formation in the synclinal shaft and buried at depths of 700-1000 m should be the first considered for development.展开更多
The second member of the Triassic Xujiahe Formation in the Sanhuiba area in Huaying Mountain is an important section of sedimentary delta facies in the Chongqing Tianfu Geological Survey and Training Base. In spite of...The second member of the Triassic Xujiahe Formation in the Sanhuiba area in Huaying Mountain is an important section of sedimentary delta facies in the Chongqing Tianfu Geological Survey and Training Base. In spite of some initial efforts on its lithology and lithofacies, the existing research is yet to be completed and suffers from contradictory conclusions and inadequate evidence. Starting from the sedimentary microfaeies types and cyclic features, we analyzed the vertical sequence of a sedimentary delta model and discovered that this section is a constructional delta deposit. Eight incomplete and asymmetric regressive cycles are marked off, given that frequent erosion surfaces appeared in the section. Based on the analysis of structural characteristics of every monocycle, we summarized the system of cycles, tracts and sequence characteristics of the overall section. In view of this systematic series of cycles, we discussed the features of the syndepositional tectonic movements in the area and conclude that, due to frequent erosion, migration and diversion of a sub-channel branch was brought about by oscillating movements of the crust. In a comparison with neighboring sections, we explored the cause of erosion and the relations between erosion and cycles. This study greatly strengthens existing research and theories, makes an important and comprehensive contribution to geological surveys and training in the area and provides essential suggestions for coal exploration, oil and gas evaluation and in general to exploration and development in the target stratum.展开更多
1 Introduction Shale formations bear abundant mineral resource and*unconventional petroleum resource,and the unconventional petroleum resource that contain in the shale formation should be integrated and researched.
Drilling,seismic and logging data were used to evaluate the hydrocarbon accumulation conditions of the mound-shoal complexes in the platform margin of the fourth member of Sinian Dengying Formation in the east side of...Drilling,seismic and logging data were used to evaluate the hydrocarbon accumulation conditions of the mound-shoal complexes in the platform margin of the fourth member of Sinian Dengying Formation in the east side of the Mianzhu-Changning intracratonic rift in the Sichuan Basin.The four understandings are:(1)The platform margin belt of the Deng 4 Member can be divided into three sections,northern,middle and southern;the middle section is at the core of the Gaoshiti-Moxi paleouplift and the structural high now,while the southern and northern sections are at the slope of the paleouplift and the structural lows now;the three sections have similar development characteristics and reservoir features of platform margin mound-shoal complex.(2)In the margin of the east side of the rift,there are several faults nearly perpendicular to the platform margin belt,the faults divide the platform margin belt into rugged paleo-landform,and the high part developed platform margin mound-shoal complexes and the reservoirs are good in physical properties,while the low part developed inter-beach depression and no mound-shoal complexes,where the reservoirs are poor in physical properties.(3)The six groups of faults nearly perpendicular to the platform margin belt divide the platform margin belt into seven large mound-shoal complexes which have similar hydrocarbon accumulation conditions and accumulation evolution process and are rich in petroleum.(4)The inter shoal depressions between the mound-shoal complexes are characterized by tighter lithology,which can block the updip direction of the mounds and shoals at the lower part of the slope of the paleouplift and are favorable for the later preservation of mound-shoal gas reservoirs.This has been proved by Well Jiaotan 1 and Heshen 2 drilled successfully.The mound-shoal complexes on the platform margin of the structural slope area have a good exploration prospect.展开更多
Lacustrine turbidite of Chang-7 Member in the studied area consists of sihstone and fine sandstone with respect to grain size, which is feldspathic lithie sandstone, syrosem arkose and arkose with respect to mineral c...Lacustrine turbidite of Chang-7 Member in the studied area consists of sihstone and fine sandstone with respect to grain size, which is feldspathic lithie sandstone, syrosem arkose and arkose with respect to mineral constitution affected by provenance. There are such apparent signatures as lithology, sedimentary structure, sedimentary sequence and well logs, to recognize turbidite. During the paleogeographic evolution of Chang-7 Member, lake basin and deep lake are both at their maximum extent during Chang-73 stage, resulting in the deposition of Zhangjiatan shale with widespread extent and of turbidite with fragmental-like. Deep lake line is gradually moving toward lake center and turbidite sand bodies are gradually turning better with better lateral continuity, connectivity and more thickness, from stages of Chang-73, Chang-72 and Chang-7t, which can be favorable reservoir in deep-water.展开更多
The glutenite in the fourth member of Shahejie Formation(Es^4) in northern Dongying depression straightforwardly penetrated into the muddy bathyal -abyss facies.The conditions of reservoir is very superior:(1) the hig...The glutenite in the fourth member of Shahejie Formation(Es^4) in northern Dongying depression straightforwardly penetrated into the muddy bathyal -abyss facies.The conditions of reservoir is very superior:(1) the high quality thick bedded oil source rock is developed very well in the Lijin sag and Minfeng sag of the study area,and it has the higher capability of generating hydrocarbon;(2) the展开更多
To reveal the effect of shale reservoir characteristics on the movability of shale oil and its action mechanism in the lower third member of the Shahejie Formation(Es3l), samples with different features were selected ...To reveal the effect of shale reservoir characteristics on the movability of shale oil and its action mechanism in the lower third member of the Shahejie Formation(Es3l), samples with different features were selected and analyzed using N2 adsorption, high-pressure mercury injection capillary pressure(MICP), nuclear magnetic resonance(NMR), high-speed centrifugation, and displacement image techniques. The results show that shale pore structure characteristics control shale oil movability directly. Movable oil saturation has a positive relationship with pore volume for radius > 2 μm, as larger pores often have higher movable oil saturation, indicating that movable oil is present in relatively larger pores. The main reasons for this are as follows. The relatively smaller pores often have oil-wetting properties because of organic matter, which has an unfavorable effect on the flow of oil, while the relatively larger pores are often wetted by water, which is helpful to shale oil movability. The rich surface provided by the relatively smaller pores is beneficial to the adsorption of immovable oil. Meanwhile, the relatively larger pores create significant pore volume for movable oil. Moreover, the larger pores often have good pore connectivity. Pores and fractures are interconnected to form a complex fracture network, which provides a good permeability channel for shale oil flow. The smaller pores are mostly distributed separately;thus, they are not conducive to the flow of shale oil. The mineral composition and fabric macroscopically affect the movability of shale oil. Calcite plays an active role in shale oil movability by increasing the brittleness of shale and is more likely to form micro-cracks under the same stress background. Clay does not utilize shale oil flow because of its large specific surface area and its block effect. The bedding structure increases the large-scale storage space and improves the connectivity of pores at different scales, which is conducive to the movability of shale oil.展开更多
The Dongfang1-1 gas field(DF1-1)in the Yinggehai Basin is currently the largest offshore self-developed gas field in China and is rich in oil and gas resources.The second member of the Pliocene Yinggehai Formation(YGH...The Dongfang1-1 gas field(DF1-1)in the Yinggehai Basin is currently the largest offshore self-developed gas field in China and is rich in oil and gas resources.The second member of the Pliocene Yinggehai Formation(YGHF)is the main gas-producing formation and is composed of various sedimentary types;however,a clear understanding of the sedimentary types and development patterns is lacking.Here,typical lithofacies,logging facies and seismic facies types and characteristics of the YGHF are identified based on high-precision 3D seismic data combined with drilling,logging,analysis and testing data.Based on 3D seismic interpretation and attribute analysis,the origin of high-amplitude reflections is clarified,and the main types and evolution characteristics of sedimentary facies are identified.Taking gas formation upper II(IIU)as an example,the plane distribution of the delta front and bottom current channel is determined;finally,a comprehensive sedimentary model of the YGHF second member is established.This second member is a shallowly buried“bright spot”gas reservoir with weak compaction.The velocity of sandstone is slightly lower than that of mudstone,and the reflection has medium amplitude when there is no gas.The velocity of sandstone decreases considerably after gas accumulation,resulting in an increase in the wave impedance difference and high-amplitude(bright spot)reflection between sandstone and mudstone;the range of high amplitudes is consistent with that of gas-bearing traps.The distribution of gas reservoirs is obviously controlled by dome-shaped diapir structural traps,and diapir faults are channels through which natural gas from underlying Miocene source rocks can enter traps.The study area is a delta front deposit developed on a shallow sea shelf.The lithologies of the reservoir are mainly composed of very fine sand and coarse silt,and a variety of sedimentary structural types reflect a shallow sea delta environment;upward thickening funnel type,strong toothed bell type and toothed funnel type logging facies are developed.In total,4 stages of delta front sand bodies(corresponding to progradational reflection seismic facies)derived from the Red River and Blue River in Vietnam have developed in the second member of the YGHF;these sand bodies are dated to 1.5 Ma and correspond to four gas formations.During sedimentation,many bottom current channels(corresponding to channel fill seismic facies)formed,which interacted with the superposed progradational reflections.When the provenance supply was strong in the northwest,the area was dominated by a large set of delta front deposits.In the period of relative sea level rise,surface bottom currents parallel to the coastline were dominant,and undercutting erosion was obvious,forming multistage superimposed erosion troughs.Three large bottom current channels that developed in the late sedimentary period of gas formation IIU are the most typical.展开更多
This study determines the geochemical and depositional environment analysis of the sediments of the Sohnari Member of the Laki Formation, Northern Kirthar Fold Belt of Pakistan. The Energy-Dispersive-X-Ray Spectroscop...This study determines the geochemical and depositional environment analysis of the sediments of the Sohnari Member of the Laki Formation, Northern Kirthar Fold Belt of Pakistan. The Energy-Dispersive-X-Ray Spectroscopy (EDS) technique is used for the detection of major elements and the effects of shifting depositional climatic conditions of six representative samples which were acquired from the Sohnari Member of the Laki Formation at Lakhra area, Sindh, Pakistan. The sedimentological studies clarify that the sediments the Sonahri Member are relatively immature and most migrated in clastic mode. The availability of Silica shows that the Member was formed due to biochemical precipitation and detrital mode and was deposited at a fast rate of sediment deposition under the fluvio-deltaic depositional system. This is also deduced that the rapid rate of sediment deposition might be created a reducing atmosphere and allowing for the mineralization of sulphur.展开更多
Based on the abundant outcrops and 3 D seismic data in Yuanba and its surrounding areas in northeastern Sichuan Basin,the characteristics,main controlling factors and development regularities of reservoirs in the four...Based on the abundant outcrops and 3 D seismic data in Yuanba and its surrounding areas in northeastern Sichuan Basin,the characteristics,main controlling factors and development regularities of reservoirs in the fourth member of Sinian Dengying Formation(shortened as Deng 4 Member)were analyzed comprehensively.The results show that the reservoirs were mainly developed in microbial dolomite associated with the microbial mound and dolarenite associated with grain beach,and had intergranular dissolution pores,inter-frame dissolution pores and karst caves as main storage space.The reservoirs were large in scale and strong in heterogeneity.The analysis of the reservoir genetic mechanisms shows that the reservoirs in the fourth member of Dengying Formation were the products of karstification on mound-beach facies deposited in the second episode of Tongwan movement.The karstification had the marks of eogenetic karstification such as granophyric karst system and half-dissociation zone.The reservoirs were controlled by the sedimentary facies belt,the mound beach facies was the decisive factor in reservoir development.Further analysis indicates that the Yuanba area had a geological background of well-developed platform margin mound beach facies,so mound beach bodies can be taken as a favorable exploration target.展开更多
The 2nd Member of Kongdian Formation has been made up of a large number of oil shale and mudstone in the Kongnan aera of Huanghua depression around the Bohai Bay.In the Kongnan area,the lake basins were very large and...The 2nd Member of Kongdian Formation has been made up of a large number of oil shale and mudstone in the Kongnan aera of Huanghua depression around the Bohai Bay.In the Kongnan area,the lake basins were very large and deep during the deposition of the 2nd Member of Kongdian Formation.During that period,the lakes were sealed,uncommunicated with the sea water and the paleoclimate was very warm and wet in Kongnan area.Analyzing the content of the trace element and the rare earth element,carbon and oxygen isotope in the disquisition,The authors prove the two views correct.展开更多
The Asmari Formation deposited in the Zagros foreland basin during the OligoceneMiocene.Lithologically,the Asmari Formation consists of limestone,dolomitic limestone,dolomite,argillaceous limestone,some anhydrite (Ka...The Asmari Formation deposited in the Zagros foreland basin during the OligoceneMiocene.Lithologically,the Asmari Formation consists of limestone,dolomitic limestone,dolomite,argillaceous limestone,some anhydrite (Kalhur Member) and sandstones (Ahwaz Member).This study is based on the analysis of core samples from four subsurface sections (wells Mn-68,Mn-281,Mn-292 and Mn-312) in the Marun Oilfieid in the Dezful embayment subzone in order to infer their provenance and tectonic setting of the Ahwaz Sandstone Member.Petrographical data reveal that the Ahwaz Sandstone comprises 97.5% quartz,1.6% feldspar,and 0.9% rock fragments and all samples are classified as quartz arenites.The provenance and tectonic setting of the Ahwaz Sandstone have been assessed using integrated petrographic and geochemical studies.Petrographic analysis reveals that mono-and poly-crystalline quartz grains from metamorphic and igneous rocks of a craton interior setting were the dominant sources.Chemically,major and trace element concentrations in the rocks of the Ahwaz Sandstone indicate deposition in a passive continental margin setting.As indicated by the CIW index (chemical index of weathering) of the Ahwaz Sandstone (average value of 82) their source area underwent "intense" recycling but "moderate to high" degree of chemical weathering.The petrography and geochemistry results are consistent with a tropical,humid climate and low-relief highlands.展开更多
A set of shale-dominated source rocks series were deposited during the heyday of lake basin development in the Member 7 of Triassic Yanchang Formation,Ordos Basin,and the thickness is about 110 m.Aimed at whether this...A set of shale-dominated source rocks series were deposited during the heyday of lake basin development in the Member 7 of Triassic Yanchang Formation,Ordos Basin,and the thickness is about 110 m.Aimed at whether this layer can form large-scale oil enrichment of industrial value,comprehensive geological research and exploration practice have been carried out for years and obtained the following important geologic findings.Firstly,widely distributed black shale and dark mudstone with an average organic matter abundance of 13.81%and 3.74%,respectively,lay solid material foundation for the formation of shale oil.Secondly,sandy rocks sandwiched in thick organic-rich shale formations constitute an oil-rich"sweet spot",the average thickness of thin sandstone is 3.5 m.Thirdly,fine-grained sandstone and siltstone reservoirs have mainly small pores of 2–8μm and throats of 20–150 nm in radius,but with a large number of micro-pores and nano-throats,through fracturing,the reservoirs can provide good conductivity for the fluid in it.Fourthly,continued high-intensity hydrocarbon generation led to a pressure difference between the source rock and thin-layer reservoir of up to 8–16 MPa during geological history,driven by the high pressure,the oil charged into the reservoirs in large area,with oil saturation reaching more than 70%.Under the guidance of the above theory,in 2019,the Qingcheng Oilfield with geologic oil reserves of billion ton order was proved in the classⅠmulti-stage superimposed sandstone shale reservoir of Chang 7 Member by the Changqing Oilfield Branch through implementation of overall exploration and horizontal well volume fracturing.Two risk exploration horizontal wells were deployed for the classⅡthick layer mud shale interbedded with thin layers of silt-and fine-sandstones reservoir in the Chang 73 submember,and they were tested high yield oil flows of more than 100 tons per day,marking major breakthroughs in petroleum exploration in classⅠshale reservoirs.The new discoveries have expanded the domain of unconventional petroleum exploration.展开更多
In the Triassic Yanchang Formation, Jiyuan-Wuqi area, Ordos Basin, the Chang 6 reservoir is contacted to the Chang 7 high-quality source rock, but the oil pools are unevenly distributed, and complex in oil and water d...In the Triassic Yanchang Formation, Jiyuan-Wuqi area, Ordos Basin, the Chang 6 reservoir is contacted to the Chang 7 high-quality source rock, but the oil pools are unevenly distributed, and complex in oil and water distribution. Through cores observation and fracture statistics, combined with comprehensive analyses of physical property, mercury injection, logging and geochemical data, and comparisons of the sandbodies scales, reservoir physical properties, argillaceous laminae and fractures between source and reservoir in the eastern and western oil-bearing areas and in the central water producing area, it is found that the hydrocarbon accumulation patterns are different in the eastern, central and western areas, and the characteristics of hydrocarbon migration under the background of double-provenance were sorted out. The study results show that the crude oil in the eastern area has different Pr/Ph and sterane distribution from that in the western area. The oil and gas primarily migrated vertically. The high-quality source rocks and favorable source-reservoir-cap combinations lay the foundation for large-scale oil and gas accumulations. Vertically, the oil and gas enrichment is controlled by the scale of sandbody and the difference of physical properties, while on the plane, it is controlled by the connectivity of sandbodies, the argillaceous laminae between source rock and reservoir, the reservoir physical property and the fractures. The sandbodies of oil-rich zones in the eastern and western areas have large thickness, low shale content, good physical properties, weak heterogeneity, few argillaceous laminae and abundant fractures, all of which are favorable for the vertical migration and accumulation of oil and gas. In contrast, in the middle area with converging provenances, the reservoirs, composed of thin sandbodies, features rapid variation in lithology and physical properties, strong heterogeneity, poor continuity of sandbodies, abundant argillaceous laminae between source rock and reservoir, and few fractures, makes it difficult for the oil and gas to migrate vertically, and results in low oil enrichment degree ultimately. For the exploration of continental multiple-provenance tight reservoirs, not only the good-property source rocks and reservoirs, but more importantly the source-reservoir contact relationship and the effect of fractures on the hydrocarbon migration and accumulation should be considered.展开更多
Santanghu Coalfield is the largest integrated coalfield exploration area in China. The major coal seams developing in Xishanyao Formation (Middle Jurassic) are the high-quality steam coals characterized by large thick...Santanghu Coalfield is the largest integrated coalfield exploration area in China. The major coal seams developing in Xishanyao Formation (Middle Jurassic) are the high-quality steam coals characterized by large thickness, favorable horizontal continuity and high coal quality. In this paper, twenty-two samples were collected from the three typical boreholes in Hanshuiquan disirict, representing the 11 coal seam sequences (7#,8#,9#,13#, 14#,15#,17#,18#,19#,20#,22#), respectively. The petrographic characteristics of the coal-bearing sequence in Xishanyao Formation were firstly summarized systematicly, and then the coal-forming swamp characteristics and succession mechanism of the coal seam in Xishanyao Formation were defined by analyzing the samples. The maceral composition, structure, geochemical and geophysical characteristics of coal are in eluded in original genetic criteria of coal-forming swamp an alysis. And the composition of coal petrography, maceral and microlithotype are the most frequently used parameters. Coal is composed of microscopic constituents and inorganic substances. The Xishanyao Formation maceral mainly consists of vitrinite (65.74%-97.01 %), inert i nite (1.93%-34%), and the exinite shows the mode of regular change. The coal-forming swamp in Xishanyao Formation possesses the characteristics of mainly marsh, wet forest swamp facies, and shallow water covered forest swamp facies, and a few of coal seams distribute in the deep water covered forest swamp facies. In addition, the sporopollens in Xishanyao Formation are mainly Pinaceae evergreen broad leaf and needle-leaved plants. Osmundaceae, Cyatheaceae and Lygodiaceae, indicating that the warm and humid tropic-subtropical climate conductive to the persistent growth of coal-forming plants in the Middle Jurassic. The coal-forming swamp shows the characteristics of vertically upward fluctuation through the periodic transition. It indicates a shallow-deep-shallow change process of the water covered depth in the swamp. This is the prin ci pal factor for the formation of the high-quality and continuous coal seam in Hanshuiquan district, Santanghu Coalfield.展开更多
Based on 991 groups of analysis data of shale samples from the Lower Member of the Cretaceous Eagle Ford Formation of 1317 production wells and 72 systematic coring wells in the U.S. Gulf Basin, the estimated ultimate...Based on 991 groups of analysis data of shale samples from the Lower Member of the Cretaceous Eagle Ford Formation of 1317 production wells and 72 systematic coring wells in the U.S. Gulf Basin, the estimated ultimate recovery(EUR) of shale oil and gas of the wells are predicted by using two classical EUR estimation models, and the average values predicted excluding the effect of engineering factors are taken as the final EUR. Key geological factors controlling EUR of shale oil and gas are fully investigated. The reservoir capacity, resources, flow capacity and fracability are the four key geological parameters controlling EUR. The storage capacity of shale oil and gas is directly controlled by total porosity and hydrocarbon-bearing porosity, and indirectly controlled by total organic carbon(TOC) and vitrinite reflectance(Ro). The resources of shale oil and gas are controlled by hydrocarbon-bearing porosity and effective shale thickness etc. The flow capacity of shale oil and gas is controlled by effective permeability, crude oil density, gas-oil ratio, condensate oil-gas ratio, formation pressure gradient, and Ro. The fracability of shale is directly controlled by brittleness index, and indirectly controlled by clay content in volume. EUR of shale oil and gas is controlled by six geological parameters: it is positively correlated with effective shale thickness, TOC and fracture porosity, negatively correlated with clay content in volume, and increases firstly and then decreases with the rise of Ro and formation pressure gradient. Under the present upper limit of horizontal well fracturing effective thickness of 65 m and the lower limit of EUR of 3×10^(4) m^(3), when TOC<2.3%, or Ro<0.85%, or clay content in volume larger than 25%, and fractures and micro-fractures aren’t developed, favorable areas of shale oil and gas hardly occur.展开更多
Based on analysis of main controlling factors of Chang 9, the source rock, driving force of migration, migration and accumulation modes, reservoir forming stages and model and enrichment law of Chang 9 reservoir were ...Based on analysis of main controlling factors of Chang 9, the source rock, driving force of migration, migration and accumulation modes, reservoir forming stages and model and enrichment law of Chang 9 reservoir were examined. The study showed that the oil of Chang 9 reservoir in the Jiyuan and Longdong(Eastern Gansu) areas came primarily from the source rock of Chang 7 Member, but the oil of Chang 9 reservoir in the Zhidan area came primarily from the source rock of Chang 9 Member. There developed lithologic-structural oil reservoirs in Gufengzhuang-Mahuangshan area in northwest Jiyuan, structural-lithologic oil reservoirs in east Jiyuan, and lithologic reservoirs in Huachi–Qingcheng area and Zhidan area. The overpressure of Chang 7 Member was the driving force of oil migration. The burial history showed that Chang 9 Member experienced two stages of reservoir forming, the reservoir formed in the Late Jurassic was smaller in charging scope and scale, and the Early Cretaceous was the period when the source rock generated oil and gas massively and the Chang 9 reservoir came into being. Along with the tectonic movements, Chang 7 bottom structure turned from high in the west and lower in the East in the sedimentary stage to high in the east and lower in the west in the hydrocarbon accumulation stage and at last to gentle western-leaning monoclinal structure at present. In Early Cretaceous, the Chang 7 bottom structure was the lowest in the west of Huanxian-Huachi-Wuqi-Dingbian areas, so the oil migrated laterally towards the higher positions around after entering the reservoir. In the main reservoir forming period, Chang 7 bottom had an ancient anticline in Mahuangshan-Hongjingzi area of west Jiyuan, controlling the oil reservoir distribution in west Jiyuan.展开更多
基金Supported by the National Natural Science Foundation of China(42202176)CNPC-Southwest University of Petroleum Innovation Consortium Cooperation Project(2020CX050103).
文摘To clarify the formation and distribution of feldspar dissolution pores and predict the distribution of high-quality reservoir in gravity flow sandstone of the 7^(th) member of Triassic Yanchang Formation(Chang 7 Member)in the Ordos Basin,thin sections,scanning electron microscopy,energy spectrum analysis,X-ray diffraction whole rock analysis,and dissolution experiments are employed in this study to investigate the characteristics and control factors of feldspar dissolution pores.The results show that:(1)Three types of diagenetic processes are observed in the feldspar of Chang 7 sandstone in the study area:secondary overgrowth of feldspar,replacement by clay and calcite,and dissolution of detrital feldspar.(2)The feldspar dissolution of Chang 7 tight sandstone is caused by organic acid,and is further affected by the type of feldspar,the degree of early feldspar alteration,and the buffering effect of mica debris on organic acid.(3)Feldspars have varying degrees of dissolution.Potassium feldspar is more susceptible to dissolution than plagioclase.Among potassium feldspar,orthoclase is more soluble than microcline,and unaltered feldspar is more soluble than early kaolinized or sericitized feldspar.(4)The dissolution experiment demonstrated that the presence of mica can hinder the dissolution of feldspar.Mica of the same mass has a significantly stronger capacity to consume organic acids than feldspar.(5)Dissolution pores in feldspar of Chang 7 Member are more abundant in areas with low mica content,and they improve the reservoir physical properties,while in areas with high mica content,the number of feldspar dissolution pores decreases significantly.
基金founded by National Natural Science Foundation of China(grant Nos.:42072186 and 42090025)National Science and Technology Major Project,China(grant No.:2016ZX05046001)+3 种基金Science and Technology Research Project of Petro China Company Limited,China(grant No.:2021DJ1806)the fund support from China Scholarship Council(No.201806440002)the International Postdoctoral Exchange Fellowship Program,China(Talent-Introduction Program,No.270152)Lin Ma wishes to acknowledge the fund support from Natural Environment Research Council,United Kingdom(NE/R013527/1)。
文摘The mineralogical development and diagenetic sequence of lacustrine shales in the Chang 7 Member of the Yanchang Formation in the Ordos Basin are detailed studied.A model of their depositional system and a diagenetic diagram are proposed in this study.Through detailed petrographic,mineralogical,and elemental analyses,four distinct shale types are identified:argillaceous shale,siliceous shale,calcareous shale,and carbonate,clay,and silt-bearing shale.The main diagenetic process in argillaceous shale is the transformation of illite to smectite,negatively impacting shale porosity.Siliceous shale undergoes carbonate cementation and quartz dissolution,contributing to increased porosity,particularly in mesopores.Calcareous shale experiences diagenesis characterised by carbonate formation and dissolution,with a prevalence of siderite.In carbonate,clay,and silt-bearing shale,the dissolution of K-feldspar contributes to illitization of kaolinite.Argillaceous shale,characterised by more clay minerals and lower mesopore volume,is identified as a potential hydrocarbon seal.Siliceous shale,with the highest pore volume and abundant inter-mineral pores,emerges as a promising shale oil reservoir.These findings contribute to a comprehensive understanding of shale properties,aiding in the prediction of shale oil exploration potential in the studied area.
基金Supported by the China Geological Survey Project(DD20190115)
文摘Pure shales in the first member of Qingshankou Formation(simplified as Qing 1 Member)in the southern Songliao Basin,i.e.,the semi-deep and deep lacustrine shales,are characterized by a high content of clay minerals and poor hydrocarbon mobility,making the development of shale oil difficult.According to the drilling and testing results,the shale of Qing 1 Member can be classified into 3 lithofacies,i.e.,bedded argillaceous shale,laminated diamictite shale,and interbedded felsic shale.The TOC and brittle minerals control the enrichment of shale oil,of them,TOC controls the total oil content,in other words,the total oil content increases with the increase of TOC;while the laminae made up of brittle minerals contain a large number of bigger intergranular pores which are favorable enrichment space for movable shale oil.In consideration of the origins of the 3 lithofacies,two shale oil enrichment models are classified,i.e.,the deep lacustrine high-TOC bedded argillaceous shale(Model-I)and the semi-deep lacustrine moderate-high-TOC laminated diamictite shale(Model-II).In the Model-I,the shale is characterized by high hydrocarbon generation ability,high total oil content,abundant horizontal bedding fractures,and vertical and high angle fractures locally;the complex fracture network formed by horizontal bedding fractures and vertical fractures improve the storage capacity and permeability of the shale reservoir,increase the enrichment space for movable oil.In the Model-II,the shale is characterized by good hydrocarbon generation ability and fairly high total oil content,and as the brittle laminae contain large intergranular pores,the shale has a higher movable oil content.Based on the two models,shale oil sweet-spot areas of 2880 km2 in the southern Songliao Basin are favorable for further exploration.Aimed at the difficulties in reservoir fracturing of the lacustrine shale with a high content of clay minerals,the composite fracturing technology with supercritical carbon dioxide was used in the shale oil reservoir for the first time,realizing large-scale volume fracturing in shale with a high content of clay minerals and strong heterogeneity,marking a breakthrough of oil exploration in continental shale with a high content of clay minerals in China.
基金the China Geological Survey Project of Chinese Oil and Gas Strategic Petroleum Prospects Investigation and Evaluation(Grant No.1211302108025—2 and No.DD20160204).
文摘There are abundant coal and coalbed methane(CBM)resources in the Xishanyao Formation in the western region of the southern Junggar Basin,and the prospects for CBM exploration and development are promising.To promote the exploration and development of the CBM resources of the Xishanyao Formation in this area,we studied previous coalfield survey data and CBM geological exploration data.Then,we analyzed the relationships between the gas content and methane concentration vs.coal seam thickness,burial depth,coal reservoir physical characteristics,hydrogeological conditions,and roof and floor lithology.In addition,we briefly discuss the main factors influencing CBM accumulation.First,we found that the coal strata of the Xishanyao Formation in the study area are relatively simple in structure,and the coal seam has a large thickness and burial depth,as well as moderately good roof and floor conditions.The hydrogeological conditions and coal reservoir physical characteristics are also conducive to the enrichment and a high yield of CBM.We believe that the preservation of CBM resources in the study area is mainly controlled by the structure,burial depth,and hydrogeological conditions.Furthermore,on the basis of the above results,the coal seam of the Xishanyao Formation in the synclinal shaft and buried at depths of 700-1000 m should be the first considered for development.
基金provided by the National Natural Science Foundation of China (Nos. 50678182 and 40802001)the Natural Science Foundation of Chongqing City (No.2008 BA0015)the Research Fund for Teaching Reform in Institutes of Higher Learning, Chongqing, China (No.09-3-094)
文摘The second member of the Triassic Xujiahe Formation in the Sanhuiba area in Huaying Mountain is an important section of sedimentary delta facies in the Chongqing Tianfu Geological Survey and Training Base. In spite of some initial efforts on its lithology and lithofacies, the existing research is yet to be completed and suffers from contradictory conclusions and inadequate evidence. Starting from the sedimentary microfaeies types and cyclic features, we analyzed the vertical sequence of a sedimentary delta model and discovered that this section is a constructional delta deposit. Eight incomplete and asymmetric regressive cycles are marked off, given that frequent erosion surfaces appeared in the section. Based on the analysis of structural characteristics of every monocycle, we summarized the system of cycles, tracts and sequence characteristics of the overall section. In view of this systematic series of cycles, we discussed the features of the syndepositional tectonic movements in the area and conclude that, due to frequent erosion, migration and diversion of a sub-channel branch was brought about by oscillating movements of the crust. In a comparison with neighboring sections, we explored the cause of erosion and the relations between erosion and cycles. This study greatly strengthens existing research and theories, makes an important and comprehensive contribution to geological surveys and training in the area and provides essential suggestions for coal exploration, oil and gas evaluation and in general to exploration and development in the target stratum.
基金supported by funding the National Basic Research Program of China (973 Program) and the grant number is 2014CB239000
文摘1 Introduction Shale formations bear abundant mineral resource and*unconventional petroleum resource,and the unconventional petroleum resource that contain in the shale formation should be integrated and researched.
基金Supported by the China National Science and Technology Major Project(2016ZX05007-002)
文摘Drilling,seismic and logging data were used to evaluate the hydrocarbon accumulation conditions of the mound-shoal complexes in the platform margin of the fourth member of Sinian Dengying Formation in the east side of the Mianzhu-Changning intracratonic rift in the Sichuan Basin.The four understandings are:(1)The platform margin belt of the Deng 4 Member can be divided into three sections,northern,middle and southern;the middle section is at the core of the Gaoshiti-Moxi paleouplift and the structural high now,while the southern and northern sections are at the slope of the paleouplift and the structural lows now;the three sections have similar development characteristics and reservoir features of platform margin mound-shoal complex.(2)In the margin of the east side of the rift,there are several faults nearly perpendicular to the platform margin belt,the faults divide the platform margin belt into rugged paleo-landform,and the high part developed platform margin mound-shoal complexes and the reservoirs are good in physical properties,while the low part developed inter-beach depression and no mound-shoal complexes,where the reservoirs are poor in physical properties.(3)The six groups of faults nearly perpendicular to the platform margin belt divide the platform margin belt into seven large mound-shoal complexes which have similar hydrocarbon accumulation conditions and accumulation evolution process and are rich in petroleum.(4)The inter shoal depressions between the mound-shoal complexes are characterized by tighter lithology,which can block the updip direction of the mounds and shoals at the lower part of the slope of the paleouplift and are favorable for the later preservation of mound-shoal gas reservoirs.This has been proved by Well Jiaotan 1 and Heshen 2 drilled successfully.The mound-shoal complexes on the platform margin of the structural slope area have a good exploration prospect.
文摘Lacustrine turbidite of Chang-7 Member in the studied area consists of sihstone and fine sandstone with respect to grain size, which is feldspathic lithie sandstone, syrosem arkose and arkose with respect to mineral constitution affected by provenance. There are such apparent signatures as lithology, sedimentary structure, sedimentary sequence and well logs, to recognize turbidite. During the paleogeographic evolution of Chang-7 Member, lake basin and deep lake are both at their maximum extent during Chang-73 stage, resulting in the deposition of Zhangjiatan shale with widespread extent and of turbidite with fragmental-like. Deep lake line is gradually moving toward lake center and turbidite sand bodies are gradually turning better with better lateral continuity, connectivity and more thickness, from stages of Chang-73, Chang-72 and Chang-7t, which can be favorable reservoir in deep-water.
文摘The glutenite in the fourth member of Shahejie Formation(Es^4) in northern Dongying depression straightforwardly penetrated into the muddy bathyal -abyss facies.The conditions of reservoir is very superior:(1) the high quality thick bedded oil source rock is developed very well in the Lijin sag and Minfeng sag of the study area,and it has the higher capability of generating hydrocarbon;(2) the
基金the National Science and Technology Major Project of China(Grant Nos.2017ZX05036-002-004.2017ZX05005-001-003)National Basic Research Program of China(Grant No.2014CB239105)for financial support.
文摘To reveal the effect of shale reservoir characteristics on the movability of shale oil and its action mechanism in the lower third member of the Shahejie Formation(Es3l), samples with different features were selected and analyzed using N2 adsorption, high-pressure mercury injection capillary pressure(MICP), nuclear magnetic resonance(NMR), high-speed centrifugation, and displacement image techniques. The results show that shale pore structure characteristics control shale oil movability directly. Movable oil saturation has a positive relationship with pore volume for radius > 2 μm, as larger pores often have higher movable oil saturation, indicating that movable oil is present in relatively larger pores. The main reasons for this are as follows. The relatively smaller pores often have oil-wetting properties because of organic matter, which has an unfavorable effect on the flow of oil, while the relatively larger pores are often wetted by water, which is helpful to shale oil movability. The rich surface provided by the relatively smaller pores is beneficial to the adsorption of immovable oil. Meanwhile, the relatively larger pores create significant pore volume for movable oil. Moreover, the larger pores often have good pore connectivity. Pores and fractures are interconnected to form a complex fracture network, which provides a good permeability channel for shale oil flow. The smaller pores are mostly distributed separately;thus, they are not conducive to the flow of shale oil. The mineral composition and fabric macroscopically affect the movability of shale oil. Calcite plays an active role in shale oil movability by increasing the brittleness of shale and is more likely to form micro-cracks under the same stress background. Clay does not utilize shale oil flow because of its large specific surface area and its block effect. The bedding structure increases the large-scale storage space and improves the connectivity of pores at different scales, which is conducive to the movability of shale oil.
基金The National Natural Science Foundation of China’s Major Project“Research on Geophysical Theories and Methods of Unconventional Oil and Gas Exploration and Development”,Task I:“China’s Tight Oil and Gas Reservoir Geological Characteristics,Classification and Typical Geological Model Establishment”under contract No.41390451。
文摘The Dongfang1-1 gas field(DF1-1)in the Yinggehai Basin is currently the largest offshore self-developed gas field in China and is rich in oil and gas resources.The second member of the Pliocene Yinggehai Formation(YGHF)is the main gas-producing formation and is composed of various sedimentary types;however,a clear understanding of the sedimentary types and development patterns is lacking.Here,typical lithofacies,logging facies and seismic facies types and characteristics of the YGHF are identified based on high-precision 3D seismic data combined with drilling,logging,analysis and testing data.Based on 3D seismic interpretation and attribute analysis,the origin of high-amplitude reflections is clarified,and the main types and evolution characteristics of sedimentary facies are identified.Taking gas formation upper II(IIU)as an example,the plane distribution of the delta front and bottom current channel is determined;finally,a comprehensive sedimentary model of the YGHF second member is established.This second member is a shallowly buried“bright spot”gas reservoir with weak compaction.The velocity of sandstone is slightly lower than that of mudstone,and the reflection has medium amplitude when there is no gas.The velocity of sandstone decreases considerably after gas accumulation,resulting in an increase in the wave impedance difference and high-amplitude(bright spot)reflection between sandstone and mudstone;the range of high amplitudes is consistent with that of gas-bearing traps.The distribution of gas reservoirs is obviously controlled by dome-shaped diapir structural traps,and diapir faults are channels through which natural gas from underlying Miocene source rocks can enter traps.The study area is a delta front deposit developed on a shallow sea shelf.The lithologies of the reservoir are mainly composed of very fine sand and coarse silt,and a variety of sedimentary structural types reflect a shallow sea delta environment;upward thickening funnel type,strong toothed bell type and toothed funnel type logging facies are developed.In total,4 stages of delta front sand bodies(corresponding to progradational reflection seismic facies)derived from the Red River and Blue River in Vietnam have developed in the second member of the YGHF;these sand bodies are dated to 1.5 Ma and correspond to four gas formations.During sedimentation,many bottom current channels(corresponding to channel fill seismic facies)formed,which interacted with the superposed progradational reflections.When the provenance supply was strong in the northwest,the area was dominated by a large set of delta front deposits.In the period of relative sea level rise,surface bottom currents parallel to the coastline were dominant,and undercutting erosion was obvious,forming multistage superimposed erosion troughs.Three large bottom current channels that developed in the late sedimentary period of gas formation IIU are the most typical.
文摘This study determines the geochemical and depositional environment analysis of the sediments of the Sohnari Member of the Laki Formation, Northern Kirthar Fold Belt of Pakistan. The Energy-Dispersive-X-Ray Spectroscopy (EDS) technique is used for the detection of major elements and the effects of shifting depositional climatic conditions of six representative samples which were acquired from the Sohnari Member of the Laki Formation at Lakhra area, Sindh, Pakistan. The sedimentological studies clarify that the sediments the Sonahri Member are relatively immature and most migrated in clastic mode. The availability of Silica shows that the Member was formed due to biochemical precipitation and detrital mode and was deposited at a fast rate of sediment deposition under the fluvio-deltaic depositional system. This is also deduced that the rapid rate of sediment deposition might be created a reducing atmosphere and allowing for the mineralization of sulphur.
基金Supported by the China National Science and Technology Major Project(2017ZX05005-003-006)
文摘Based on the abundant outcrops and 3 D seismic data in Yuanba and its surrounding areas in northeastern Sichuan Basin,the characteristics,main controlling factors and development regularities of reservoirs in the fourth member of Sinian Dengying Formation(shortened as Deng 4 Member)were analyzed comprehensively.The results show that the reservoirs were mainly developed in microbial dolomite associated with the microbial mound and dolarenite associated with grain beach,and had intergranular dissolution pores,inter-frame dissolution pores and karst caves as main storage space.The reservoirs were large in scale and strong in heterogeneity.The analysis of the reservoir genetic mechanisms shows that the reservoirs in the fourth member of Dengying Formation were the products of karstification on mound-beach facies deposited in the second episode of Tongwan movement.The karstification had the marks of eogenetic karstification such as granophyric karst system and half-dissociation zone.The reservoirs were controlled by the sedimentary facies belt,the mound beach facies was the decisive factor in reservoir development.Further analysis indicates that the Yuanba area had a geological background of well-developed platform margin mound beach facies,so mound beach bodies can be taken as a favorable exploration target.
基金Supported by Project of Dagang Branch of Petroleum Group Company Ltd,CNPC No TJDG-JZHT-2005-JSFW-0000-00339
文摘The 2nd Member of Kongdian Formation has been made up of a large number of oil shale and mudstone in the Kongnan aera of Huanghua depression around the Bohai Bay.In the Kongnan area,the lake basins were very large and deep during the deposition of the 2nd Member of Kongdian Formation.During that period,the lakes were sealed,uncommunicated with the sea water and the paleoclimate was very warm and wet in Kongnan area.Analyzing the content of the trace element and the rare earth element,carbon and oxygen isotope in the disquisition,The authors prove the two views correct.
基金the Ferdowsi University of Mashhad for their logistic support during this study
文摘The Asmari Formation deposited in the Zagros foreland basin during the OligoceneMiocene.Lithologically,the Asmari Formation consists of limestone,dolomitic limestone,dolomite,argillaceous limestone,some anhydrite (Kalhur Member) and sandstones (Ahwaz Member).This study is based on the analysis of core samples from four subsurface sections (wells Mn-68,Mn-281,Mn-292 and Mn-312) in the Marun Oilfieid in the Dezful embayment subzone in order to infer their provenance and tectonic setting of the Ahwaz Sandstone Member.Petrographical data reveal that the Ahwaz Sandstone comprises 97.5% quartz,1.6% feldspar,and 0.9% rock fragments and all samples are classified as quartz arenites.The provenance and tectonic setting of the Ahwaz Sandstone have been assessed using integrated petrographic and geochemical studies.Petrographic analysis reveals that mono-and poly-crystalline quartz grains from metamorphic and igneous rocks of a craton interior setting were the dominant sources.Chemically,major and trace element concentrations in the rocks of the Ahwaz Sandstone indicate deposition in a passive continental margin setting.As indicated by the CIW index (chemical index of weathering) of the Ahwaz Sandstone (average value of 82) their source area underwent "intense" recycling but "moderate to high" degree of chemical weathering.The petrography and geochemistry results are consistent with a tropical,humid climate and low-relief highlands.
基金Supported by the China National Science and Technology Major Project(2016ZX05050)the National Key Basic Research and Development Program(973 Program),China(2014CB239003)
文摘A set of shale-dominated source rocks series were deposited during the heyday of lake basin development in the Member 7 of Triassic Yanchang Formation,Ordos Basin,and the thickness is about 110 m.Aimed at whether this layer can form large-scale oil enrichment of industrial value,comprehensive geological research and exploration practice have been carried out for years and obtained the following important geologic findings.Firstly,widely distributed black shale and dark mudstone with an average organic matter abundance of 13.81%and 3.74%,respectively,lay solid material foundation for the formation of shale oil.Secondly,sandy rocks sandwiched in thick organic-rich shale formations constitute an oil-rich"sweet spot",the average thickness of thin sandstone is 3.5 m.Thirdly,fine-grained sandstone and siltstone reservoirs have mainly small pores of 2–8μm and throats of 20–150 nm in radius,but with a large number of micro-pores and nano-throats,through fracturing,the reservoirs can provide good conductivity for the fluid in it.Fourthly,continued high-intensity hydrocarbon generation led to a pressure difference between the source rock and thin-layer reservoir of up to 8–16 MPa during geological history,driven by the high pressure,the oil charged into the reservoirs in large area,with oil saturation reaching more than 70%.Under the guidance of the above theory,in 2019,the Qingcheng Oilfield with geologic oil reserves of billion ton order was proved in the classⅠmulti-stage superimposed sandstone shale reservoir of Chang 7 Member by the Changqing Oilfield Branch through implementation of overall exploration and horizontal well volume fracturing.Two risk exploration horizontal wells were deployed for the classⅡthick layer mud shale interbedded with thin layers of silt-and fine-sandstones reservoir in the Chang 73 submember,and they were tested high yield oil flows of more than 100 tons per day,marking major breakthroughs in petroleum exploration in classⅠshale reservoirs.The new discoveries have expanded the domain of unconventional petroleum exploration.
基金Supported by the National Natural Science Foundation of China(41872165,41572137)
文摘In the Triassic Yanchang Formation, Jiyuan-Wuqi area, Ordos Basin, the Chang 6 reservoir is contacted to the Chang 7 high-quality source rock, but the oil pools are unevenly distributed, and complex in oil and water distribution. Through cores observation and fracture statistics, combined with comprehensive analyses of physical property, mercury injection, logging and geochemical data, and comparisons of the sandbodies scales, reservoir physical properties, argillaceous laminae and fractures between source and reservoir in the eastern and western oil-bearing areas and in the central water producing area, it is found that the hydrocarbon accumulation patterns are different in the eastern, central and western areas, and the characteristics of hydrocarbon migration under the background of double-provenance were sorted out. The study results show that the crude oil in the eastern area has different Pr/Ph and sterane distribution from that in the western area. The oil and gas primarily migrated vertically. The high-quality source rocks and favorable source-reservoir-cap combinations lay the foundation for large-scale oil and gas accumulations. Vertically, the oil and gas enrichment is controlled by the scale of sandbody and the difference of physical properties, while on the plane, it is controlled by the connectivity of sandbodies, the argillaceous laminae between source rock and reservoir, the reservoir physical property and the fractures. The sandbodies of oil-rich zones in the eastern and western areas have large thickness, low shale content, good physical properties, weak heterogeneity, few argillaceous laminae and abundant fractures, all of which are favorable for the vertical migration and accumulation of oil and gas. In contrast, in the middle area with converging provenances, the reservoirs, composed of thin sandbodies, features rapid variation in lithology and physical properties, strong heterogeneity, poor continuity of sandbodies, abundant argillaceous laminae between source rock and reservoir, and few fractures, makes it difficult for the oil and gas to migrate vertically, and results in low oil enrichment degree ultimately. For the exploration of continental multiple-provenance tight reservoirs, not only the good-property source rocks and reservoirs, but more importantly the source-reservoir contact relationship and the effect of fractures on the hydrocarbon migration and accumulation should be considered.
基金National Natural Science Foundation Project (Grant No. 41662010)Xinjiang Uygur Autonomous Region University Scientific Research Program For Young Teachers Research And Cultivation Fund Project (Grant No. XJEDU20I6S038).
文摘Santanghu Coalfield is the largest integrated coalfield exploration area in China. The major coal seams developing in Xishanyao Formation (Middle Jurassic) are the high-quality steam coals characterized by large thickness, favorable horizontal continuity and high coal quality. In this paper, twenty-two samples were collected from the three typical boreholes in Hanshuiquan disirict, representing the 11 coal seam sequences (7#,8#,9#,13#, 14#,15#,17#,18#,19#,20#,22#), respectively. The petrographic characteristics of the coal-bearing sequence in Xishanyao Formation were firstly summarized systematicly, and then the coal-forming swamp characteristics and succession mechanism of the coal seam in Xishanyao Formation were defined by analyzing the samples. The maceral composition, structure, geochemical and geophysical characteristics of coal are in eluded in original genetic criteria of coal-forming swamp an alysis. And the composition of coal petrography, maceral and microlithotype are the most frequently used parameters. Coal is composed of microscopic constituents and inorganic substances. The Xishanyao Formation maceral mainly consists of vitrinite (65.74%-97.01 %), inert i nite (1.93%-34%), and the exinite shows the mode of regular change. The coal-forming swamp in Xishanyao Formation possesses the characteristics of mainly marsh, wet forest swamp facies, and shallow water covered forest swamp facies, and a few of coal seams distribute in the deep water covered forest swamp facies. In addition, the sporopollens in Xishanyao Formation are mainly Pinaceae evergreen broad leaf and needle-leaved plants. Osmundaceae, Cyatheaceae and Lygodiaceae, indicating that the warm and humid tropic-subtropical climate conductive to the persistent growth of coal-forming plants in the Middle Jurassic. The coal-forming swamp shows the characteristics of vertically upward fluctuation through the periodic transition. It indicates a shallow-deep-shallow change process of the water covered depth in the swamp. This is the prin ci pal factor for the formation of the high-quality and continuous coal seam in Hanshuiquan district, Santanghu Coalfield.
基金Supported by the PetroChina Science and Technology Department Project(2012A-4802-02)National Key Basic Research and Development Program(2014CB239000)。
文摘Based on 991 groups of analysis data of shale samples from the Lower Member of the Cretaceous Eagle Ford Formation of 1317 production wells and 72 systematic coring wells in the U.S. Gulf Basin, the estimated ultimate recovery(EUR) of shale oil and gas of the wells are predicted by using two classical EUR estimation models, and the average values predicted excluding the effect of engineering factors are taken as the final EUR. Key geological factors controlling EUR of shale oil and gas are fully investigated. The reservoir capacity, resources, flow capacity and fracability are the four key geological parameters controlling EUR. The storage capacity of shale oil and gas is directly controlled by total porosity and hydrocarbon-bearing porosity, and indirectly controlled by total organic carbon(TOC) and vitrinite reflectance(Ro). The resources of shale oil and gas are controlled by hydrocarbon-bearing porosity and effective shale thickness etc. The flow capacity of shale oil and gas is controlled by effective permeability, crude oil density, gas-oil ratio, condensate oil-gas ratio, formation pressure gradient, and Ro. The fracability of shale is directly controlled by brittleness index, and indirectly controlled by clay content in volume. EUR of shale oil and gas is controlled by six geological parameters: it is positively correlated with effective shale thickness, TOC and fracture porosity, negatively correlated with clay content in volume, and increases firstly and then decreases with the rise of Ro and formation pressure gradient. Under the present upper limit of horizontal well fracturing effective thickness of 65 m and the lower limit of EUR of 3×10^(4) m^(3), when TOC<2.3%, or Ro<0.85%, or clay content in volume larger than 25%, and fractures and micro-fractures aren’t developed, favorable areas of shale oil and gas hardly occur.
基金Supported by China National Science and Technology Major Project(2016ZX05050,2017ZX05001002-008)the PetroChina Science and Technology Major Project(2016E-0501)
文摘Based on analysis of main controlling factors of Chang 9, the source rock, driving force of migration, migration and accumulation modes, reservoir forming stages and model and enrichment law of Chang 9 reservoir were examined. The study showed that the oil of Chang 9 reservoir in the Jiyuan and Longdong(Eastern Gansu) areas came primarily from the source rock of Chang 7 Member, but the oil of Chang 9 reservoir in the Zhidan area came primarily from the source rock of Chang 9 Member. There developed lithologic-structural oil reservoirs in Gufengzhuang-Mahuangshan area in northwest Jiyuan, structural-lithologic oil reservoirs in east Jiyuan, and lithologic reservoirs in Huachi–Qingcheng area and Zhidan area. The overpressure of Chang 7 Member was the driving force of oil migration. The burial history showed that Chang 9 Member experienced two stages of reservoir forming, the reservoir formed in the Late Jurassic was smaller in charging scope and scale, and the Early Cretaceous was the period when the source rock generated oil and gas massively and the Chang 9 reservoir came into being. Along with the tectonic movements, Chang 7 bottom structure turned from high in the west and lower in the East in the sedimentary stage to high in the east and lower in the west in the hydrocarbon accumulation stage and at last to gentle western-leaning monoclinal structure at present. In Early Cretaceous, the Chang 7 bottom structure was the lowest in the west of Huanxian-Huachi-Wuqi-Dingbian areas, so the oil migrated laterally towards the higher positions around after entering the reservoir. In the main reservoir forming period, Chang 7 bottom had an ancient anticline in Mahuangshan-Hongjingzi area of west Jiyuan, controlling the oil reservoir distribution in west Jiyuan.