Longitudinal vibration characteristics of a tapered pipe pile considering the vertical support of surrounding soil and construction disturbance

This research is concentrated on the longitudinal vibration of a tapered pipe pile considering the vertical support of the surrounding soil and construction disturbance.First,the pile-soil system is partitioned into finite segments in the vertical direction and the Voigt model is applied to simulate the vertical support of the surrounding soil acting on the pile segment.The surrounding soil is divided into finite ring-shaped zones in the radial direction to consider the construction disturbance.Then,the shear complex stiffness at the pile-soil interface is derived by solving the dynamic equilibrium equation for the soil from the outermost to innermost zone.The displacement impedance at the top of an arbitrary pile segment is obtained by solving the dynamic equilibrium equation for the pile and is combined with the vertical support of the surrounding soil to derive the displacement impedance at the bottom of the upper adjacent segment.Further,the displacement impedance at the pile head is obtained based on the impedance function transfer technique.Finally,the reliability of the proposed solution is verified,followed by a sensitivity analysis concerning the coupling effect of the pile parameters,construction disturbance and the vertical support of the surrounding soil on the displacement impedance of the pile.

Analytical solutions for the restraint effect of isolation piles against tunneling-induced vertical ground displacements

This paper presents a simplified elastic continuum method for calculating the restraint effect of isolation piles on tunneling-induced vertical ground displacement,which can consider not only the relative sliding of the pile‒soil interface but also the pile rowesoil interaction.The proposed method is verified by comparisons with existing theoretical methods,including the boundary element method and the elastic foundation method.The results reveal the restraining mechanism of the isolation piles on vertical ground displacements due to tunneling,i.e.the positive and negative restraint effects exerted by the isolation piles jointly drive the ground vertical displacement along the depth direction from the original tunneling-induced nonlinear variation situation to a relatively uniform situation.The results also indicate that the stiffness of the pile‒soil interface,including the pile shaft‒surrounding soil interface and pile tip-supporting soil interface,describes the strength of the pile‒soil interaction.The pile rows can confine the vertical ground displacement caused by the tunnel excavation to the inner side of the isolation piles and effectively prevent the vertical ground displacement from expanding further toward the outer side of the isolation piles.

Horizontal dynamic response of a large-diameter pipe pile considering the second-order effect of axial force

The second-order effect of axial force on horizontal vibrating characteristics of a large-diameter pipe pile is theoretically investigated.Governing equations of the pile-soil system are established based on elastodynamics.Threedimensional wave equations of soil are decoupled through differential transformation and variable separation.Consequently,expressions of soil displacements and horizontal resistances can be obtained.An analytical solution of the pile is derived based on continuity conditions between the pile and soil,subsequently from which expressions of the complex impedances are deduced.Analyses are carried out to examine the second-order effect of axial force on the horizontal vibrating behavior of the pipe pile.Some conclusions can be summarized as follows： stiffness and damping factors are decreased with the application of axial force on the pile head; distributions of the pile horizontal displacement and rotation angle are regenerated due to the second-order effect of the applied axial force; and redistributions of the bending moment and shearing force occur due to the second-order effect of the applied axial force.

Study on the Horizontal Movement State of Suction Anchor Piles for Offshore Wind Power during Horizontal Pulling

The subsea anchor piles of offshore wind power floating platform structures are mainly subjected to uplift and horizontal loads, and this paper focuses on the case of horizontal loads. A three-dimensional numerical simulation study of the horizontal pullout characteristics of wind power suction anchor piles in clay layers was carried out to reveal the horizontal movement state of the anchor piles during horizontal pile pullout, the range of pile depth at the pullout point where the horizontal movement is achieved (referred to as the horizontal movement range), the relationship between the pullout load and the ultimate load during the horizontal movement, and the optimal location of the pullout point for the horizontal movement. The results show that at certain pull-out points, the anchor pile produces an overall horizontal movement state under suitable horizontal pull-out loads. The depth of the pile pull-out point for horizontal movement is in the middle and lower part of the pile, i.e. 14.2 m to 14.5 m. The horizontal pull-out load of 24,000 kN at a depth of 14.5 m within the pile horizontal movement range of 14.2m to 14.5 m is the maximum ultimate horizontal pull-out load;the optimum pull-out point depth is 14.5 m at 0.275 L (L is the pile length). For each pull-out point of the anchor pile in horizontal movement, the horizontal pull-out load in horizontal movement and the horizontal ultimate pull-out load existed and it was found that the two values were not exactly the same, the values were compared and it was found that at the optimum pull-out point the value of the ultimate horizontal pull-out load/horizontal pull-out load in horizontal movement tended to 1.

The Vertical Deformation and Horizontal Displacement Fields,Movement, and Seismicity of the Island Arc Tectonics

In this work,the vertical deformation,horizontal displacement,and stress fields of arcuate tectonics are theoretically derived from the horizontal tectonic stress; then the characteristics of tectonic movement,seismicity,and focal mechanism of arcuate tectonics of the entire world are explained.It is pointed out that the island arc and other arcuate tectonics are gradually developed under the displacement and stress fields of the arcuate tectonics and that the under-thrusting action of the ocean plate is secondary.The distance formulas between the volcanic arc and the trench are suggested and also that theoretical results are consistent with actual data.

Dynamic evolution of crustal horizontal deformation before the Ms6.4 Menyuan earthquake

An Ms6.4 earthquake occurred in the Menyuan county of Qinghai Province on Jan 21, 2016. In order to recognize the development of horizontal deformation and distinguish precursory deformation anomalies, we obtained coordinates time series, velocity and strain model around the seismic zones from processing of continuous observations from 2010 and 6 times of surveying Global Positioning System （GPS） data since 2009. The results show that, before the earthquake, the eastern segmentation of the Qilian tectonic zone where the Lenglongling Fault located is in strong crustal shortening and compressional strain state with dilatational rates of -15 to -25 ppb. The Lenglongling Fault has a strike-slip rate of 3.1 mm/a and a far-field differential orthogonal rate of 7 mm/a, while differential rate is only 1.2 mm/a near the fault, which reflects its locking feature with strain energy accumulation and high seismic risks. Dynamic evolution of deformation model shows that preevent dilatational rates around the seismic zones increases from 15 ppb/a to -20 ppb/a with its center moving to the source areas. Time series of N components of G337 station, which is 13.7 km away from the Lenglongling Fault, exhibit a 5 mm/a acceleration anomaly. Time series of base-station QHME （in Menyuan） displays a reverse acceleration from the end of Sep. to Dec., 2016 when it comes to a largest deviation, and the accumulative displacement is more than 4 mm and the value reverse till the earthquake. In our results, coseismic displacement of N, E, U components in QHME site are 3.0 mm, 3.0 mm, -5.4 mm, respectively. If we profile these values onto the Lenglongling Fault, we can achieve a 1.1 mm of strike slip and 4.1 mm updip slip relative to the hanging wall.

Effects of topography on dynamic responses of single piles under vertical cyclic loading

This paper describes model tests of single piles subjected to vertical cyclic compressive loading for three kinds of topography: sloping ground, level ground, and inclined bedrock. Comprehensive dynamic responses involving cyclic effects and vibration behaviours are studied under various load combinations of dynamic amplitude, mean load,frequency and number of cycles. Test results show that permanent settlement can generally be predicted with a quadratic function or power function of cycles.Sloping ground topography produces more pronounced settlement than level ground under the same load condition. For vibration behaviour,displacement amplitude is weakly affected by the number of cycles, while load amplitude significantly influences dynamic responses. Test results also reveal that increasing load amplitude intensifies nonlinearity and topography effects. The strain distribution in a pile and soil stress at the pile tip are displayed to investigate the vibration mechanism accounting for sloping ground effects. Furthermore, the dynamic characteristics among three kinds of topography in the elastic stage are studied using a three-dimensional finite method. Numerical results are validated by comparing with experimental results for base inclination topography. An inclined soil profile boundary causes non-axisymmetric resultant deformation, though a small difference in vertical displacement is observed.

Model tests and numerical analyses on horizontal impedance functions of inclined single piles embedded in cohesionless soil

Horizontal impedance functions of inclined single piles are measured experimentally for model soil-pile systems with both the effects of local soil nonlinearity and resonant characteristics.Two practical pile inclinations of 5掳 and 10掳 in addition to a vertical pile embedded in cohesionless soil and subjected to lateral harmonic pile head loadings for a wide range of frequencies are considered.Results obtained with low-to-high amplitude of lateral loadings on model soil-pile systems encased in a laminar shear box show that the local nonlinearities have a profound impact on the horizontal impedance functions of piles.Horizontal impedance functions of inclined piles are found to be smaller than the vertical pile and the values decrease as the angle of pile inclination increases.Distinct values of horizontal impedance functions are obtained for the ＇positive＇ and ＇negative＇ cycles of harmonic loadings,leading to asymmetric force-displacement relationships for the inclined piles.Validation of these experimental results is carried out through three-dimensional nonlinear finite element analyses,and the results from the numerical models are in good agreement with the experimental data.Sensitivity analyses conducted on the numerical models suggest that the consideration of local nonlinearity at the vicinity of the soil-pile interface influence the response of the soil-pile systems.

Transient response of piles-bridge under horizontal excitation

Moving ships and other objects drifting on water often impact a bridge' s pile foundations. The mechanical model of the piles-bridge structure under horizontal forcing was established, and a time-domain approach based on Finite-difference Method was developed for analyzing the dynamic response of the piles-bridge structure. For a single pile, good agreement between two computed results validated the present approach.The slenderness ratio of the pile, the pile-soil stiffness ratio and the type of the structure influence the dynamic response of the piles-bridge structure. The computed results showed that the stiffness of the structure determines the dynamic response of the piles-bridge structure under horizontal forcing.

Observed deformation characteristics of a deep excavation for the spring area in Jinan,China

The observed deflections and internal forces of pile-anchor retaining excavation were studied in spring area in Jinan city of China. Based on field measured data, the ground surface settlement, deflection of retaining piles and wall, internal force analysis of concrete piles, axial anchoring forces, groundwater table, and the deformation of surround building and pipelines were investigated. The results indicates that the combining application of concrete piles, jet grouting columns and anchors support system can effectively control excavation-induced surface ground settlements. The field maximum lateral wall deflections are between 0.o2% and o.19% of the excavation depth due to the competitive site conditions. The bending moment-depth relationship curve is S-type. Groundwater leakage results in the sharp drop in groundwater level, which is part of the reasons for the adjacent building settlement. The axial anchoring forces of the upper layer of anchors increase gradually during the excavation, but those of the lower layer of anchors slightly reduced firstly and then tend to be stable during the excavation procedure. In comparison with the histories of excavation cases, the small lateral wall deflection in this study results from the favorable site condition and the relative rigidity of the retaining structure system.

Vertical and horizontal displacements of a reservoir slope due to slope aging effect,rainfall,and reservoir water

Landslides are common hazards in reservoir areas and significantly affect dam operation and human lives.For the prevention and management of landslides,accurate assessment of the factors influencing their generation is essential.This study evaluated the key external factors influencing horizontal and vertical displacements of Luobogang Reservoir Slope in Hanyuan County,China.Displacements had been monitored by a surface-displacement-monitoring system consisting of 118 GPS stations during 2012-2015.To identify the external driving factors,their influence zones,and slope responses,we analyzed 32 months of displacement measurements and other multi-source datasets using the empirical orthogonal function.Overall,the results show that slope aging effect,rainfall,and reservoir water levels are three main driving factors.For horizontal displacement,aging effect is the most critical factor and predominantly affects the edges of landslides,the gob cave,and the public building zones.The secondary factor is the reservoir water level,which mainly acts on the boundary between the slope and reservoir water surface.The closer the slope zone is to the reservoir water,the more significant the impact is.Regarding vertical displacement,the most important factor is rainfall.The vertical displacement caused by rainfall accounts for 56.76% of the total vertical displacements.However,rainfall induces elastic displacements that generally cause less damage to the slope.The secondary factor is aging effect,and the vertical displacement caused by aging effect accounts for 9.42%.However,seven individual zones are highly affected by slope aging effect,which is consistent with the distribution of public buildings.

3D Finite Elements Technique for Collapse Causes of the Pylons in Egyptian Temples: A Study of the Great Pylon of Ramesseum Temple, Luxor, Egypt

This research presents damage causes of the pylons in the ancient Egyptian temples based on 3D finite elements analysis. The main purpose of the research determines the failure causes of the first pylon of the Ramessium temple, which is situated in Upper Egypt, at Luxor “Thebes” on the west bank of the Nile River. The first pylon of Ramessium temple subjected to seismic activity effects on long term, combined with several structural damage factors such as the defects resulting from the construction technique, where the builder used the poor quality of stones in foundations of the pylon, the building materials residue was used as filler for the core of the pylon walls, and it lacked vertical joints between the courses. In addition to it founded on alluvial soil that is vulnerable to contaminated water, it is still suffering damage factors and urban trespasses at the moment. All of the former factors helped the pylon to be affected by the earthquakes loads that occurred on it. The structural behavior of the pylon under self-weight and earthquakes loads were carried out by Numerical analysis to find out the loads and stresses which caused collapsing of the pylon. Results of the study indicated that the pylon subjected to a horizontal displacement due to old earthquakes force, led to collapse of the pylon. Finally, the study represents use of modern technique to study the structural behavior of the most important architectural units in ancient Egyptian temples to identify the causes of its collapse.

Analysis of horizontal displacement distribution caused by single advancing longwall panel excavation

The paper presents an analysis of the horizontal displacement of surfaces induced by exploitation in a longwall panel. The panel under discussion is No. 698 of Prosper Haniel coal mine, Germany. The author discusses both the distribution of displacement vectors, according to the theory assuming surface point displacement towards the center of gravitation （COG） zone of a selected deposit element, and the analysis of horizontal displacement measurements, based on the assumption that the value of horizontal displacement is proportional to the slope of the subsidence trough. Finally, the value of horizontal displacement coefficient B is estimated for particular longitudinal and transverse measurement section of the analyzed longwall No. 698.

A Theoretical Study the Effect of Openings in Infill Wall Panels on the Behavior of Structures

Two dimensional,reinforced concrete building frames built on raft foundation and having infill wall panels with openings in them are analysed using the direct stiffness method.Beams and columns are modelled by beam column elements.Wall panels are modelled by plane stress finite elements.The raft foundation is modelled by uniaxial finite elements.The soil is modelled as half space model.Openings in wall panels are introduced by using fictitious beams between real floor beams. A computer program is written to carry out the static analysis and do the necessary comparison to show the effect of openings on the structural behavior.

Analysis of dynamical response to large deformation of piles with initial displacements

In this paper, a nonlinear mathematical model for analyzing dynamical response to the large deformation of piles with initial displacements is firstly established with the arc-coordinate, and it is a set of nonlinear integral-differential equa- tions, in which, the Winkeler model is used to simulate the resistance of the soil to the pile. Secondly, a set of new auxiliary functions are introduced. The differential-integral equations are transformed into a set of nonlinear differential equations, and the differential quadrature method （DQM） and the finite difference method （FDM） are applied to discretize the set of nonlinear equations in the spatial and time domains, respectively. Then, the Newton-Raphson method is used to solve the set of discretization algebraic equations at each time step. Finally, numerical examples are presented, and the dynamical re- sponses to the deformation of piles, including configuration, bending moment and shear force, are graphically illuminated. In calculation, two types of initial displacements and dynamical loads are applied, and the effects of parameters on the dynamical responses of piles are analyzed in detail.

Analytical expressions for determining the stability of cohesionless soil slope under generalized seismic conditions

In recent major earthquakes, the researchers have found the need for consideration of vertical seismic acceleration for the stability analysis of the man-made and natural slopes. However, in most past studies, the performance of slopes has been assessed by accounting only the horizontal seismic component of the ground motion, without giving due weightage to the effect of vertical component. In the present study, analytical expressions are derived to determine the factor of safety, yield seismic coefficient and consequently the seismic displacement of cohesionless soil slope under combined horizontal and vertical components of the ground motion. The derivation uses the Newmark's sliding block approach, in which the soil slope with a planar failure surface within the framework of conventional pseudo-static analysis is assumed to follow the Mohr-Coulomb failure criterion. The effects of vertical seismic coefficient on the stability of cohesionless slope have been studied through a set of graphical presentations for a specific range of soil parameters. It is observed that overlooking the effect of the vertical component of the ground motion on factor of safety and the displacement while designing the slope may be detrimental, resulting in the slope failure. The general expressions presented in this paper may be highly useful in the field of earthquake geotechnical engineering practice for designing the cohesionless soil slopes under combined horizontal and vertical seismic loads.

Analysis on the Observation Data of Three Profiles across the Qilian Mountain-Haiyuan Fault Zone

By analyzing GPS, leveling and gravity observation data from the Minle, Huazangsi and Shagouhe profiles across the Qilian Mountain-Haiyuan fault during 2005 - 2009, the changes of these data and activity characteristics of the main faults in different time are obtained. The results show that the Changma-Erbo, Maomaoshan, Zhunglanghe and Haiyuan faults have been active in recent years. The relationship between the vertical displacement and mobile gravity data is analyzed, and the results reveal the gravity changes are mainly due to mass transfer. The results of GPS observation show that the direction of the horizontal movement velocity was almost along the fault strike in 2006 - 2007, while the horizontal velocity deviated from the fault direction in 2007 - 2008, characterized by increased eastward displacement. Further analysis upon removal of the linear trend on the time series of the N and E coordinate values of the continuous observation stations of the Crustal Movement Observation Network of China near the three profiles reveals that the Wenchuan earthquake had an effect on the observations in 2007 - 2008. Comparing the gravitational changes in 2008 - 2009 with the Bouguer gravity anomaly background, we find that the area near Minle profile is in the stage of adjustment and recovery, while the anomaly is not completely recovered around Huazangsi and Shagouhe profiles.

Scaling of residual displacements in terms of elastic and inelastic spectral displacements for existing SDOF systems

Structures undergoing inelastic displacements during earthquake ground motions are known to sustain some amount of residual displacements, which may make them unusable or unsafe. In this study an attempt is made to estimate residual displacements for elastic-perfectly-plastic single-degree-of-freedom oscillators with a given lateral strength ratio. It is observed in the case of a class of ground motions that there are no trends in the dependence of residual displacement on the temporal features of the ground motion, and thus any estimation of residual displacements should be carried out only in the statistical sense. Statistical estimation of residual displacement spectrum via normalization with respect to inelastic or elastic spectral displacements is considered, and it is found that normalization with respect to inelastic spectral displacements is preferable. Expressions for residual displacement spectra are proposed for both types of normalizations and for the givenlateral-strength-ratio type oscillators.

Three-dimensional finite element analysis on effects of tunnel construction on nearby pile foundation

A three-dimensional finite element simulation was carried out to investigate the effects of tunnel construction on nearby pile foundation.The displacement controlled model (DCM) was used to simulate the tunneling-induced volume loss effects.The numerical model was verified based on the results of a centrifuge test and a set of parametric studies was implemented based on this model.There is good agreement between the trend of the results of the centrifuge test and the present model.The results of parametric studies show that the tunnelling-induced pile internal force and deformation depend mainly on the pile?tunnel distance,the pile length to tunnel depth ratio and the volume loss.Two different zones are separated by a 45° line projected from the tunnel springline.Within the zone of influence,the pile is subjected to tensile force and large settlement;whereas outside the zone of influence,dragload and small settlement are induced.It is also established that the impact of tunnelling on a pile group is substantially smaller as compared with a single pile in the same location with the rear pile in a group,demonstrating a positive pile group effect.

Displacement and deformation analysis for uplift piles

On the assumptions that the shear resistance increases linearly with increasing shear displacement between the uplift pile and surrounding soil, that the axis force is distributed as parabola along the pile length, that elastic distortion occurs when the pile is loaded, that the displacement of pile is in accord with that of the soil, and that the uplift pile failure is regarded as the soil failure, a rational calculation method was proposed for calculating the deformation, ultimate displacement and shear resistance of piles. The distributions of frictional resistance and the shear displacement along the pile length were obtained with the method. The comparisons were made between the measurement results and the present results. The present theoretical results agree well with the measurement results, with the average difference being less than 12% before failure. The comparisons show that the proposed method is reasonable for uplift design and engineering construction of piles.