Bio-cementation for tidal erosion resistance improvement of foreshore slopes based on microbially induced magnesium and calcium precipitation

In most coastal and estuarine areas,tides easily cause surface erosion and even slope failure,resulting in severe land losses,deterioration of coastal infrastructure,and increased floods.The bio-cementation technique has been previously demonstrated to effectively improve the erosion resistance of slopes.Seawater contains magnesium ions(Mg^(2+))with a higher concentration than calcium ions(Ca^(2+));therefore,Mg^(2+)and Ca^(2+)were used together for bio-cementation in this study at various Mg^(2+)/Ca^(2+)ratios as the microbially induced magnesium and calcium precipitation(MIMCP)treatment.Slope angles,surface strengths,precipitation contents,major phases,and microscopic characteristics of precipitation were used to evaluate the treatment effects.Results showed that the MIMCP treatment markedly enhanced the erosion resistance of slopes.Decreased Mg^(2+)/Ca^(2+)ratios resulted in a smaller change in angles and fewer soil losses,especially the Mg^(2+)concentration below 0.2 M.The decreased Mg^(2+)/Ca^(2+)ratio achieved increased precipitation contents,which contributed to better erosion resistance and higher surface strengths.Additionally,the production of aragonite would benefit from elevated Mg^(2+)concentrations and a higher Ca^(2+)concentration led to more nesquehonite in magnesium precipitation crystals.The slopes with an initial angle of 53°had worse erosion resistance than the slopes with an initial angle of 35°,but the Mg^(2+)/Ca^(2+)ratios of 0.2:0.8,0.1:0.9,and 0:1.0 were effective for both slope stabilization and erosion mitigation to a great extent.The results are of great significance for the application of MIMCP to improve erosion resistance of foreshore slopes and the MIMCP technique has promising application potential in marine engineering.

Recovery of cobalt and nickel in the presence of magnesium and calcium from sulfate solutions by Versatic 10 and mixtures of Versatic 10 and Cyanex 301

The extraction and stripping characteristics of Versatic 10 and its mixtures with Cyanex 301 were investigated for the recovery of cobalt and nickel from sulfate solutions containing magnesium and calcium. The optimum extraction factors of Versatic 10 were initial pH of 2.5, O/A ratio of 1/3, and saponification rate of 60%. The loaded Versatic 10 was stripped by using 2 mol/L H2SO4 at O/A ratio of 1/1. The optimum volume ratio of Versatic 10 to Cyanex301 was 7/3 in the mixtures, which could effectively reduce the equilibrium pH to 3.50. And the loaded mixtures were stripped by using 2 mol/L H2SO4at O/A ratio of 1/2. The reaction principle of Versatic10 and metal ions is an ion exchange reaction. However, in the extraction reaction of and metal ions, besides the ion exchange reaction, the strong coordination effect between Cyanex 301 and metal ions also exists, which is much weakened in the extraction reaction of the mixtures and metal ions.

Novel mechanism for the modification of Al_2O_3-based inclusions in ultra-low carbon Al-killed steel considering the effects of magnesium and calcium

Many researchers have explored the inclusion modification mechanism to improve non-metallic inclusion modifications in steelmaking. In this study, two types of industrial trials on inclusion modifications in liquid steel were conducted using ultra-low-carbon Al-killed steel with different Mg and Ca contents to verify the effects of Ca and Mg contents on the modification mechanism of Al_2O_3-based inclusions during secondary refining. The results showed that Al_2O_3-based inclusions can be modified into liquid calcium aluminate or a multi-component inclusion with the addition of a suitable amount of Ca. In addition, [Mg] in liquid steel can further reduce CaO in liquid calcium aluminate to drive its evolution into CaO–MgO–Al_2O_3 multi-component inclusions. Thermodynamic analysis confirmed that the reaction between [Mg] and CaO in liquid calcium aluminate occurs when the MgO content of liquid calcium aluminate is less than 3 wt% and the temperature is higher than 1843 K.

Separation of manganese from calcium and magnesium in sulfate solutions via carbonate precipitation

The separation of manganese from sulfate solutions containing 14.59 g/L Mn2+, 1.89 g/L Mg2+ and 1.54 g/L Ca2+ was preformed successfully by carbonate precipitation. The results of thermodynamic analysis and tests indicate that carbonate precipitation holds better selectivity for manganese over magnesium than hydroxide precipitation and the feeding method is the most critical factor for minimizing the co-precipitation of calcium and magnesium. Furthermore, with adding MnSO4 solution to NH4HCO3 solution, the effects of the initial NH4HCO3 concentration, NH4HCO3 amount, solution pH value, reaction temperature and time on carbonate precipitation were evaluated and the optimum precipitation conditions were obtained. Under the optimum conditions, the precipitation rates of Mn2+, Ca2+ and Mg2+ are 99.75%, 5.62% and 1.43%, respectively. Moreover, the prepared manganese carbonate was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDX). The results demonstrate that the product can be indexed to the rhombohedral structure of MnCO3.

THE STUDY ON THE CHANGES OF ZINC, COPPER, CALCIUM AND MAGNESIUM IN PLASMA AND ERYTHROCYTES DURING CARDIOPULMONARY BYPASS

Objective To study the changes and their influence factors involved of zinc, copper, calcium and magnesium in plasma and erythrocytes during cardiopulmonary bypass(CPB). Methods Zinc, copper, calcium and magnesium values in plasma and erythrocytes were measured by atomic absorption spectrophotometer during CPB. Results Zinc and copper levels in plasma were significantly elevated above preinduction level before perfusion, but calcium and magnesium levels did not change significantly; zinc, copper and calcium levels in plasma were significantly below preoperation level during CPB, but magnesium level in plasma was significantly increased above preoperation; zinc level in plasma was increased to preoperation level after CPB and began to decrease again at 8 hours after CPB, copper level in plasma was increased to preoperation level at 20 hours after CPB, calcium in plasma was increased significantly from beginning to 8 hours after CPB, magnesium level in plasma was decreased to preoperation level at 8 hours afterCPB. Concentration of zinc , copper, calcium and magnesium in erythrocytes did not change significantly. Conclusion During CPB, the changes of zinc, copper, calcium and magnesium had relation to hemodilution, operative wound, carrier protein, stress and component of priming solution and cardioplegic solution, but no relation to transfer from plasma erythrocytes. The results indicate that it is beneficial to patient's recovery to supplement zinc, copper, calcium and magnesium properly by different ways during cardiac perioperation.

Removal of magnesium and calcium from electric furnace titanium slag by H_3PO_4 oxidation roasting-leaching process

H3PO4 oxidation roasting followed by HCl acid leaching was proposed to remove magnesium and calcium from electric furnace titanium slag containing 3.12% MgO and 0.86% CaO. XRF, XRD and SEM techniques were used to characterize the composition, mineral phase component and microstructure of the titanium slag. The H3PO4 oxidation thermodynamic, mineral phase transformation, microstructure, element distribution in titanium slag during H3PO4 oxidation process and leaching process were investigated. The thermodynamic analysis indicated that H3PO4 could promote the decomposition of MgTi2O5 and CaSiO3. The results indicated that H3PO4 could effectively promote the transformation of titanium-bearing mineral to rutile and enrich the impurities in MxTi（3-x）O5 into phosphate which could be removed by acid leaching process. Under the studied conditions, the leaching rates of magnesium and calcium reached 94.68% and 87.19%, respectively. The acid leached slag containing 0.19% MgO and 0.13% CaO（mass fraction） was obtained.

Effects of Foliar Spraying of Magnesiumpotassium Sulfate Fertilizer on Absorption of Magnesium, Potassium and Calcium in Differentposition Tobacco Leaves

[Objective] ln the Mg-deficient （exchangeable Ca/Mg ratio ＆gt; 20） tobacco-growing areas in Qujing City of Yunnan Province, the ratio of Ca/Mg was adjusted by applying Mg fertilizer in soil and spraying Mg fertilizer on tobacco leaves. ln ad-dition, the effects of Mg fertilization on the absorption of K, Ca and Mg in flue-cured tobacco leaves were investigated, providing theoretical basis and production guidance for the balanced fertilization technology in the Mg-deficient flue-cured to-bacco-growing areas in Qujing City of Yunnan Province. [Method] The field plot test and randomized complete block design were adopted in this research. The group without Mg fertilization was treated as control. There were 3 treatment groups for foliar spraying of magnesium-potassium sulfate fertilizer and 2 treatment groups for soil application ＋ foliar spraying of magnesium-potassium sulfate fertilizer. The tobac-co roots, stems, lower leaves, middle leaves and upper leaves were dried and weighed. They were grinded for the determination of K, Ca and Mg content. The total K, Ca and Mg content in upper （B2F）, middle （C3F） and lower （X2F） flue-cured tobacco leaves in each plot was measured. [Result] The foliar spraying and soil application ＋ foliar spraying al increased the absorption of Mg and K in middle and lower tobacco leaves and the absorption of Ca in lower tobacco leaves, but de-creased the absorption of Mg, K and Ca in upper leaves and the absorption of Ca in middle leaves. Among the positions, the accumulated distribution of Mg, K and Ca ranked as middle leaves ＆gt; lower leaves ＆gt; upper leaves. With the application of Mg fertilizer, the Ca/Mg ratio and K/Mg ratio al decreased in middle and upper to-bacco leaves; while the Ca/Mg ratio increased in the lower tobacco leaves, and the K/Mg ratio showed no significant difference among treatment groups. [Conclusion] The foliar spraying and soil application ＋ foliar spraying of magnesium-potassium sulfate fertilizer affected the Ca/Mg ratio and K/Mg ratio in tobacco leaves mainly through affecting the absorption of Mg.

The unimodal latitudinal pattern of K,Ca and Mg concentration and its potential drivers in forest foliage in eastern China

Potassium(K),calcium(Ca),and magnesium(Mg)are essential elements with important physiological functions in plants.Previous studies showed that leaf K,Ca,and Mg concentrations generally increase with increasing latitudes.However,recent meta-analyses suggested the possibility of a unimodal pattern in the concentrations of these elements along latitudinal gradients.The authenticity of this unimodal latitudinal pattern,however,requires validation through large-scale field experimental data,and exploration of the underlying mechanisms if the pattern is confirmed.Here,we collected leaves of common species of woody plants from 19 montane forests in the north-south transect of eastern China,including 322 species from 160 genera,67 families;and then determined leaf K,Ca,and Mg concentrations to explore their latitudinal patterns and driving mechanisms.Our results support unimodal latitudinal patterns for all three elements in woody plants across eastern China,with peak values at latitude 36.5±1.0°N.The shift of plant-functional-type compositions from evergreen broadleaves to deciduous broadleaves and to conifers along this latitudinal span was the key factor contributing to these patterns.Climatic factors,mainly temperature,and to a lesser extent solar radiation and precipitation,were the main environmental drivers.These factors,by altering the composition of plant communities and regulating plant physiological activities,influence the latitudinal patterns of plant nutrient concentrations.Our findings also suggest that high leaf K,Ca,and Mg concentrations may represent an adaptive strategy for plants to withstand water stress,which might be used to predict plant nutrient responses to climate changes at large scales,and broaden the understanding of biogeochemical cycling of K,Ca,and Mg.

Effects of Paper Mill Sludge on Potassium, Sodium, Calcium, and Magnesium Concentrations in Different Soybean Cultivars

A field experiment was conducted on a sandy loam soil at an Experimental Farm in Taejon, South Korea, to determine the effects of paper mill sludge compost application rates on K, Na, Ca and Mg concentrations of soybean (Glycine max (L.) Merr.) aboveground tissues and the genotypic effects on the concentrations of these elements. Sludge compost treatments of 0, 75, and 150 t ha-1 were applied to 30 diverse soybean cultivars. Concentrations of K, Na, Ca, and Mg in aboveground tissues harvested 69 days after …

Refinement Role of Electromagnetic Stirring and Calcium in AZ91 Magnesium Alloy

Effects of calcium addition and electromagnetic stirring on the microstructure of AZ91 magnesium alloy and refinement mechanism were investigated. The results show that calcium addition ranging from 0.1wt% to 0.3 wt% does not lead to formation of any new phases but cause the refinement of ascast microstructure.However, combined calcium alloying and electromagnetic stirring significantly decrease the grain size, change the morphologies of the β-Mg17Al12 phases,and reduce their volume percentage. The minimum grain size of AZ91 alloy is obtained in the case of the addition of 0.2 wt%Ca with exciting voltage of 100 V. The microstructural refinement is attributed to the increase of the degree of undercooling and nucleation temperature of primary α-Mg phases on the basis of DTA analysis results.

Recent advances in hydrothermal modification of calcium phosphorus coating on magnesium alloy

Magnesium(Mg) and its alloys have emerged as a favored candidate for bio-regenerative medical implants due to their superior biocompatibility, biodegradability and the elastic modulus close to that of human bone. Unfortunately, the rapid and uncontrollable degradation rate of Mg alloys in chloride-rich body microenvironments limits their clinical orthopedic applications. Recently, Calcium Phosphate(Ca-P)biomaterials, especially Hydroxyapatite(HA), have been broadly applied in the surface functional modification of metal-based biomaterials attributed to their excellent bioactivity and biocompatibility. Hydrothermal modification of Ca-P coatings on Mg alloys has been extensively exploited by researchers for its significant superiorities in controlling coating structure and improving interfacial bonding strength for better osseointegration and corrosion resistance. This work focuses on the up-to-the-minute advances in Ca-P coatings on the surface of Mg and its alloys via hydrothermal methods, including the strategies and mechanisms of hydrothermal modification. Herein, we are inclined to share some feasible and attractive hydrothermal surface modification strategies. From the perspectives of hydrothermal manufacturing technique innovation and coating structure optimization, we evaluate how to foster the corrosion resistance, coating bonding strength, osseointegration and antibacterial properties of Mg alloys with Ca-P coatings synthesized by hydrothermal method. The challenges and future perspectives on the follow-up exploration of Mg alloys for orthopedic applications are also elaborately proposed.

Review on the phosphate-based conversion coatings of magnesium and its alloys

Magnesium(Mg)and its alloys are lightweight as well as biocompatible and possess a high strength-to-weight ratio,making them suitable for many industries,including aerospace,automobile,and medical.The major challenge is their high susceptibility to corrosion,thereby limiting their usability.The considerably lower reduction potential of Mg compared to other metals makes it vulnerable to galvanic coupling.The oxide layer on Mg offers little corrosion resistance because of its high porosity,inhomogeneity,and fragility.Chemical conversion coatings(CCs)belong to a distinct class because of underlying chemical reactions,which are fundamentally different from other types of coating.Typically,a CC acts as an intermediate sandwich layer between the base metal and an aesthetic paint.Although chromate CCs offer superior performance compared to phosphate CCs,yet still they release carcinogenic hexavalent chromium ions(Cr^(6+));therefore,their use is prohibited in most European nations under the Registration,Evaluation,Authorization and Restriction of Chemicals legislation framework.Phosphate-based CCs are a cost-effective and environment-friendly alternative.Accordingly,this review primarily focuses on different types of phosphate-based CCs,such as zinc,calcium,Mg,vanadium,manganese,and permanganate.It discusses their mechanisms,current status,pretreatment practices,and the influence of various parameters-such as pH,temperature,immersion time,and bath composition-on the coating performance.Some challenges associated with phosphate CCs and future research directions are also elaborated.

The Role of Calcium in Microstructural Refinement of AZ91 Magnesium Alloy

The effect of calcium addition on the microstructures of AZ91 magnesium alloy was investigated. It was found that a small amount of calcium in AZ91 allay produced a large decrease in the α- Mg grain size and the dispersed fine β-Mgt7 Alt2 phases. In addition, some Al4Ca particles were found to exist in the AZ91 alloy containing 0.5wt% Ca. EDS analysis and water-quenched technique revealed that the grain-refining mechanism of calcium for the AZ91 alloys was mainly attributed to the role of restricting growth of calcium in the primary α-Mg crystals.

Synthesis of Environmentally Friendly Multifunctional Metal (Calcium,Magnesium) Oleate Detergent with Antioxidation Property

This article covers a method for synthesizing environmentally friendly multifunctional metal (calcium,magnesium) oleate detergents with antioxidation property.These multifunctional metal (calcium,magnesium) oleate detergents with antioxidation property were synthesized using oil-soluble liquid antioxidants (PPIBP,PPIBTSTBP,and PPIBPDA) as reactive functional materials.These oil-soluble liquid antioxidants have the potential to be used as functional materials for application in synthesizing other kinds of substrate detergents.

Recent advances of electromagnetic interference shielding Mg matrix materials and their processings:A review

In terms of lightweight electromagnetic interference(EMI)shielding structural materials,Mg matrix materials have proven to be the best,due to their exciting properties(e.g.low density,high specific strength,good electrical conductivity and excellent EMI shielding properties)and their wide range of applications in lightweighting in electronics,automotive and aerospace industries.Through processing,such as alloying,heat treatment,plastic deformation and composite processing,Mg matrix materials can be obtained with tailorable properties which can play a key role in designing materials for EMI shielding.This work introduces an overview of the research on the EMI shielding properties of Mg matrix materials as well as their EMI shielding mechanisms over the past few decades,focused on the influence of alloying,heat treatment,plastic deformation and composite processing for the EMI shielding properties of Mg matrix materials.At the end,conclusions and future perspectives are provided.

Simultaneous Determination of Calcium and Magnesium in Water Using Artificial Neural Network Spectro-Photometric Method

A new analytical method using Back-Propagation （BP） artificial neural networks and spectrophotometry for simultaneous determination of calcium and magnesium in tap water, the Yellow River water and seawater is established. By condition experiment, the optimum analytical conditions for calcium, magnesium and Arsenazo （Ⅲ） color reactions are obtained. Levenberg- Marquart （L-M） algorithm is used for calculation in BP neural network. The topological structure of three-layer BP ANN network architecture is chosen as 11-10-2 （nodes）. The initial value of gradient coefficient μ is fixed at 0.001 and the increase factor and reduction factor of kt take the default values of the system. The data are processed by computers with our own programs written in MATLAB 7.0. The relative standard deviations of the calculated results for calcium and magnesium are 2.31% and 2.14%, respectively. The results of standard addition method show that the recoveries of calcium and magnesium are 103.6% and 100.8% in the tap water, 103.2% and 96.6% in the Yellow River water （Lijin district of Shandong Province）, and 98.8%-103.3% and 98.43%-103.4% in seawater from Jiaozhou Bay of Qingdao. It is found that 14 common cations and anions do not interfere with the determination of calcium and magnesium under the optimum experimental conditions. The comparative experiments do not show any obvious differ- ence between the results obtained by this new method and those obtained by the classical complexometric titration method in seawater medium. This method exhibits good reproducibility and high accuracy in the determination of calcium and magnesium and can be used for the simultaneous determination of Ca^2＋ and Mg^2＋ in tap water and natural water.

The role of Ca,Al and Zn on room temperature ductility and grain boundary cohesion of magnesium

It is know from literature that small additions(<1 wt%)of Ca,Al and Zn significantly improve the intrinsic ductility of Mg.The exact role of each element,both qualitatively and quantitatively,and their combined effects,however,are poorly understood.Here we achieved a much clearer view on the quantitative role of each element with respect to ductility improvement and on the collaborative effect,particularly of Ca and Zn in Mg.Some of our findings and conclusions are in disagreement with data and interpretation found in literature.Four different alloys,namely,Mg-0.1 Ca,Mg-0.1 Ca-1 Al,Mg-0.05 Ca-1 Al,Mg-0.1 Ca-2 Al-1 Zn(all are in wt%)were selected for this investigation.All alloys were treated such that approx.similar grain sizes and textures were obtained.This largely excludes the effect of extrinsic factors on ductility.EBSD-guided slip trace analyses reveal that the addition of Ca eases activation of prismatic and pyramidal II slip systems.Using in-situ deformation experiments in SEM and atom probe tomography observations of grain boundaries direct evidence is given for the individual and synergetic effects of Ca and Zn on grain boundary cohesion as an important contribution to improve the ductility of these alloys.We conclude that Ca reduces the slip anisotropy and ameliorates ductility,however,the weak grain boundary cohesion in the Mg-0.1 wt%Ca alloy limits the material’s tensile ductility.The addition of Zn alters the Ca segregation at the grain boundaries and helps to retain their cohesive strength,an effect which thus enables higher ductility and strength.The further addition of Al primarily improves the strength.The results show that the balanced influence of reduced slip anisotropy on the one hand and increased grain boundary cohesion on the other hand allow to design a high strength high ductility rare-earth free Mg alloy.

Structure, Formation, Properties, and Application of Calcium and Magnesium Silicate Hydrates System—A Review

In order to expand the advantages of strong durability and high compressive strength of calcium silicate hydrates(C-S-H),at the same time to make up for the poor early mechanical strength of magnesium silicate hydrates (M-S-H),we present the features and advantages of C-S-H and M-S-H and a comprehensive review of the progress on CaO-MgO-SiO_(2)-H_(2)O.Moreover,we systematically describe natural calcium and magnesium silicate minerals and thermodynamic properties of CaO-MgO-SiO_(2)-H_(2)O.The effect of magnesium on C-S-H and calcium on M-S-H is summarized deeply;the formation and structural feature of CaO-MgO-SiO_(2)-H_(2)O is also explained in detail.Finally,the development of calcium and magnesium silicate hydrates in the future is pointed out,and the further research is discussed and estimated.

Microstructure and mechanical properties of ZA62 based magnesium alloys with calcium addition

As-cast microstructure and mechanical properties of Mg-6Zn-2Al-0.3Mn (ZA62) alloys with calcium addition were investigated.The as-cast microstructure of the base alloy ZA62 consists of the α-Mg matrix and eutectic phase Mg51Zn20.The Mg51Zn20 eutectic was gradually replaced by MgZn phase and Mg32(Al,Zn)49 phase when calcium is added into the base alloy.Further addition of calcium leads to the increase of grain boundary phases and formation of a new quaternary Mg-Zn-Al-Ca eutectic compound.In comparison with the base alloy,the increase of calcium addition to the base alloy results in the reduction of both strength and ductility at ambient temperature,but increase at elevated temperatures due to the thermal stability of Ca-containing phases.At elevated temperatures,the creep resistance of ZA62 based alloys containing calcium is significantly higher than that of AZ91 which is the most commonly used magnesium alloy.

Role of calcium and magnesium infusion in prevention of oxaliplatin neurotoxicity. A phase III trial

Objective： This study is a prospective randomized, double-blind, placebo-controlled study to evaluate the effect of calcium and magnesium （Ca/Mg） infusion on amelioration of oxaliplatin neuropathy, the dose-limiting toxicity. Methods： Sixty patients with resected colorectal carcinoma （CRC） planned to receive adjuvant oxaliplatin-containing regimen were randomly assigned to two arms; Arm A： patients received Ca/Mg were given as 1 gm Ca gluconate and 1 gm MgSO4 in 250 mL of intravenous （IV） solution over 30 rain pre and post oxaliplatin infusion, and Arm B： patients received 250 mL of IV solution without Ca/Mg over 30 min pre and post oxaliplatin infusion. Primary outcome was to assess percentage of patients with oxaliplatin-induced neurotoxicity. Neurotoxicity was assessed according to the National Cancer Institute Common Terminology Criteria forAdverse Events （NCI-CTCAE） version 3.0. Results： Sixty patients in both arms were assessed, 30 with Ca/Mg infusion and 30 without. Patients developed neurotoxicity in arm A were significantly lower than that in arm B after the end of treatment; 7 （23.3%） and 14 （46.6%） respectively （P 〈 0.05）, and significantly lower duration of neuropathy in months （8 ± 2.5 vs 18 ±3） respectively （P 〈 0.001）. Conclusion： Use of IV Ca/Mg showed a statistically significant reduction of peripheral neuropathy （PN） in patients with CRC receiving oxaliplatin in the adjuvant settings.