Assessing the Impact of Industrial Zones on the Environmental Pollution in Hai Phong’s Coastal Areas, Vietnam

Pollution in the coastal areas negatively affects biochemical indicators of seawater, human health and marine organisms. Hai Phong is a coastal city of Vietnam with the development of socio-economic activities, representing through an increasing number of industrial zones. This study is to evaluate the pollution of large industrial zones in Hai Phong city using numerical models. The numerical simulation (MIKE 21 SW, FM, ECO Lab) models were applied to simulate the wave propagation, hydraulic regime, water quality in coastal Hai Phong area. The MIKE 21 ECO Lab model was used to evaluate sources of waste from the large coastal industrial zones to some aquaculture zones. The calibration and validation results of wave propagation and the hydrodynamic models were resonably good, with Nash coefficient ranging from 0.65 to 0.90 and a percent bias (PBIAS) from 5.6% to 9.4%. The simulation results of water quality and concentration of pollutants (DO, BOD5, COD, TSS, Fe, and Coliform) in 2023 at the aquaculture locations show that the BOD5, COD, and TSS concentrations were higher than the allowable limits stated in the national technical regulation on surface water quality (QCVN 08:2023/BTNMT) and lower than the allowable limits stated in the national technical regulation on marine water quality (QCVN 10:2023/BTNMT). The outcomes of this study will provide more information to support managers to come up with a better socio-economic development plan for Hai Phong city to achieve sustainable development.

Quantitative Analysis and Affecting Factors of the Overlapping Degree of Interfacial Transition Zone between Neighboring Aggregates in Concrete

Based on the nearest surface function formula, a quantitative formula to measure the overlapping degree between the interfacial transition zone （ITZ） of neighboring aggregate particles was put forward. The formula was further deduced to quantitatively analyze the influence of the volume fraction of aggregate, ITZ thickness and the maximum aggregate diameter on the overlapping degree between neighboring ITZ. The volume of ITZ was quantitatively calculated in actual concrete by comparing the nearest surface function formula with an approximate method, that is the surface area of the aggregates multiplied by the uniform thickness of the ITZ layers. The results showed that the influencing order of these three factors on the overlapping degree between neighboring ITZ in turn was the interface thickness, aggregate volume fraction and the maximum aggregate diameter; As long as the interface thickness 50 μm and the aggregate volume fraction 50%, the calculated error between two methods mentioned above is about 10 %.

Dispersion attenuation structure of the crust around the Weifang-Jiashan segment of the Tanlu fault zone in North China

On the condition that the velocity ratio of compressive wave to shear wave is stable during the propagating process of seismic wave, this paper develops an estimation method for medium quality factor based on single station＇s travel time difference between direct S and P waves and the first period signal of direct P wave. 8 774 high SNR wave data altogether recorded by 75 stations are analyzed. The results show that： （1） under the normal regional stress field, the quality factors QmsP in the stable tectonic area are higher than that in the active tectonic area around the Weifang-Jiashan section and its surrounding area in the Tanlu fault zone; （2） in the Juxian-Tancheng section the seismic wave attenuation is relatively quick, and the media is relatively broken, suggesting no tectonic stress accumulation; （3） the Xinyi-Sihong section is currently locking and in accumulating elastic strain energy stage, which has the deep environment and conditions of strong earthquake generation similar to those of the 1668 M8.5 Tancheng strong earthquake.

Spatial Pattern and Development of Protected Areas in the North-south Transitional Zone of China

The north-south transitional zone in China mainly consists of the Qinling-Daba Mountains. It is the most important West-East geo-ecological space in China, containing protected areas vital for biodiversity conservation and ecological security of China. The protection and rational development of its natural habitat is of great significance to China’s ecological security and integration of protected areas based on mountain forest ecosystems on a global scale. In this study, five important types of protected areas in the transitional zone were selected, and their spatial patterns were analysed. Spatial analysis methods, such as kernel density estimation and accessibility analysis, were employed for both point and areal data, and focused on four aspects: land use scale, shift in the centre of gravity, spatial agglomeration, and accessibility. In addition, policy background and evolution of spatial and temporal characteristics of the protected area system in the transitional zone from 1963 to 2017 were also examined. We analysed the characteristics and geographical significance of the West-east corridor using the spatial pattern of the protected area system from the perspective of ecological and economic spaces. We focused on spatial shape, type intersection, and key areas to analyse the spatial overlap of the protected areas. Protected area establishment was divided into three stages: initial(1956–1980), rapid development(1981–2013), and national park transformation(2014–present). These stages reflected the change in the concept of ‘simple protection—sustainable use—integration and upgrade’ for protected areas of China. The spatial centre of gravity of the protection zone system was located in the west Qinling-Daba Mountains, and its high-density core exhibited a relatively stable N-shaped structure composed of four gathering areas. Affected by factors such as geographic environment and socio-economic development density, the average access time for protected areas was high(1.56 h);wetland parks and scenic areas are located closer to the city centre. As the West-east corridor in the transitional zone extends from west to east, there is a clear spatial dislocation between the development of protected areas and the intensity of human activities. During development, differentiated goal orientation should be adopted based on the idea of zoning and classified governance. With the advancement of the construction of protected areas, the spatial overlap of protected areas in the transition zone has become more prominent. At present, the spatially overlapped protected areas in the transitional zone remain prominent, with inclusion overlap being the most common, and forest parks exhibiting the highest probability of overlap with other protected areas, we should focus on in the integration process of the corridor-type ecological space based on the mountain forest ecosystem.

Study of the engineering geologic feature of weathering zone of bedrock in 810 producing area of Luling Mine

For a safe extracting of the mine resource of the razor thin capping rock, a study of waterproof, sand prevention, roof fall prevention must be made. As a result, it’s necessary to master the engineering feature of weathering zone of bedrock. According to the lithology appraisal and X diffract analyses, the mineral feature of weathering zone of bedrock in 810 producing area has been studied in this article. By testing the physical mechanics index of weathering zone, we have found out some features of physical mechanic quality. Utilizing the determined result of viscosity index and slaking test, we reach a conclusion of the water stability of weathering zone, that is the weathering zone rock belongs to the type that is easily slaked when encountered water and the water stability is weak.

Strata Architectural Variability and Facies Distribution in a Structural Transfer Zone: A Case Study of Fushan Sag, Northern South China Sea

Structural transfer zones in a half-graben rift basin play a significant role in controlling sandy sediments and providing a target for hydrocarbon exploration. Previous studies have classified the transfer zone in lacustrine environments into two different patterns: synthetic approaching transfer zones and synthetic overlapping transfer zones. However, the evolution of the depositional pattern and the controlling factors of the above transfer zones are still unclear. In the Fushan Sag, the northern South China Sea, an overlapping transfer zone developed in the early Eocene Epoch, while a synthetic approaching transfer zone developed in the late Eocene, due to tectonic uplift. This evolutionary process provided an opportunity to study the stacking pattern of strata architectural variability and facies distribution in the structural transfer zone of the Eocene lacustrine basin. In this study, following the indications of the oriented sedimentary structures in core samples and heavy mineral assemblages of 18 wells, the evolution of the paleo-hydrodynamic distribution during the early and late Eocene has been reconstructed. The sequence-stratigraphy was then divided and the sand body parameters calculated, according to the seismic data and well log interpretations. During the early Eocene, the lake level was at a low stand, the faults broken displacement in the East block being over 50 m. The prograding delta and turbidites are oriented perpendicular to the structural transfer zone. According to the quantitative analysis of the flow rate and the depositional parameters, we speculate that gravity transportation of the sediment and the sediment-supply are the dominating factors during this period. Up to the late Eocene, the rising lake level and the decreased fault displacement leads the flow to divert to a NE-direction, resulting in it being parallel to the axis of the transfer zone. Thus, we speculate that the accommodation space is predominant in this period. In comparison with the above two periods, a braided river delta with an isolated sand body and turbidites developing in the deep area is prominent in the overlapping transfer zone, while a meandering river delta is characteristic of the synthetic approaching transfer zone.

Surface quality, microstructure and mechanical properties of Cu-Sn alloy plate prepared by two-phase zone continuous casting

Cu-4.7%Sn （mass fraction） alloy plate was prepared by the self-developed two-phase zone continuous casting （TZCC） process. The relationship between process parameters of TZCC and surface quality of the alloy plate was investigated. The microstructure and mechanical properties of the TZCC alloy plate were analyzed. The results show that Cu-4.7%Sn alloy plate with smooth surface can be obtained by means of reasonable matching the entrance temperature of two-phase zone mold and the continuous casting speed. The microstructure of the TZCC alloy is composed of grains-covered grains, small grains with self-closed grain boundaries, columnar grains and equiaxed grains. Compared with cold mold continuous casting Cu-4.7%Sn alloy plate, the room temperature tensile strength and ductility of the TZCC alloy plate are greatly improved.

Assessment and Application of Beach Quality Based on Analytic Hierarchy Process in Yangkou Beach, Qingdao

The whole-beach quality assessment is the basis of building and preserving beautiful beaches.The beach quality assessment index system and assessment standard have been established based on the attributes of beaches(including the width,slope,landform,and types),sorting coefficient,and softness degree of surface sediment.The assessment weight of each index for quality evaluation was analyzed using the analytic hierarchy process,and comprehensive scores of selected beach profiles were calculated in accordance with the light assessment standard.A beach quality evaluation model based on index weight and scores was established in this paper.The factors of 12 profiles of Yangkou Beach in Qingdao City were surveyed to carry out a quality assessment,and the comprehensive scores of each profile were calculated in accordance with the evaluation model.The results showed that the quality of Yangkou Beach can be divided into four ratings:excellent,good,medium,and poor.The excellent-quality area includes a wide and flat dry beach zone and soft,flat,and clean intertidal and subtidal zones covered with well-sorted fine sand,and leisure sports,such as volleyball,running,and swimming,are suitable for tourists.The good-quality area features a slightly narrow and dry beach zone,moderately soft and uneven intertidal and subtidal zones covered with fine sand and a small tidal gully,and a small amount of foreign matter;leisure sports,such as walking and running,are suitable for tourists.This study recommends the building of fixed drainage ditches or underground culverts to reduce the tidal gully.The medium-quality area consisted of a narrow and dry beach zone,moderately soft and uneven intertidal and subtidal zones covered by poorly sorted medium sand,a tide ditch,and a small amount of foreign matter.In this area,walking is suitable for tourists.Sand should be supplemented in the intertidal zone.The poor-quality area contained a very narrow and dry beach zone covered with poor-sorted gravel,a very chaotic intertidal zone with a considerable amount of foreign matters,such as bricks and rocks,wide tidal ditches,and an uneven subtidal zone with some reefs;leisure sports are unsuitable here.Thus,foreign matter and reefs should be removed,and the dry beach zone should be supplemented with sand.Therefore,the beach quality assessment is a very useful tool for building beautiful beaches.

Fault-Growth Pattern of the South Margin Normal Fault of the Yuguang Basin in Northwest Beijing and its Influencing Factors

Based on high-resolution remote sensing image interpretation, digital elevation model 3-D analysis, field geologic field investigation, trenching engineering, and ground-penetrating radar, synthetic research on the evolution of the Yuguang Basin South Margin Fault （YBSMF） in northwest Beijing was carried out. We found that the propagation and growth of faults most often occurred often at two locations： the fault overlapping zone and the uneven or rough fault segment. Through detailed observation and analysis of all cropouts of faults along the YBSMF from zone a to zone i, we identified three major factors that dominate or affect fault propagation and growth. First, the irregularity of fault geometry determine the propagation and growth of the fault, and therefore, the faults always propagate and grow at such irregular fault segments. The fault finally cuts off and eliminates its irregularity, making the fault geometry and fault plane smoother than before, which contributes to the slipping movement of the half-graben block in the basin. Second, the scale of the irregularity of the fault geometry affects the result of fault propagation and growth, that is, the degree of the cutting off of fault irregularity. The degree of cutting off decreases as irregularity scale increases. Third, the maximum possible slip displacement of the fault segment influences the duration of fault propagation and growth. The duration at the central segments with a large slip displacement is longer than that at the end segments with a smaller slippage value.

A New Growth Model of Fault Attributes in a Strike-Slip Fault System in the Tarim Basin

Fault attributes generally display a consistent power–law-scaling relationship.Based on new 3 D seismic data,however,we found some exceptional fault attribute relationships of lengths(L)–throw(T)(vertical component of displacement),overlap zone length(Lo)–width(Wo)from a strike-slip fault system of the Ordovician carbonates in the Tarim Basin.The L–T relationship shows two linear segments with breakup at^40 km in fault length.This presents an exceptional throw increase in the second stage,which is attributed to a localization of vertical displacement and deformation in overlapping zones other than the different fault scales in a mature fault zone.The Lo–Wo relationship in the overlapping zones shows multiply stepped-shape patterns,suggesting multiple fault differential growth and periodic increase in fault size.Therefore,we propose a new alternative growth model of fault attributes in strike-slip fault zones,in which the overlapping zones accumulated localized displacement and deformation in the intracratonic strike-slip fault zone.

Entire Catchment and Buffer Zone Approaches to Modeling Linkage Between River Water Quality and Land Cover——A Case Study of Yamaguchi Prefecture,Japan

This study investigated the linkages between river water quality and land use in river catchments in Yama- guchi Prefecture, the western Japan, in order to examine the effect of land use changes of both entire catchment and buffer zone on river water quality. Dissolved Oxygen (DO), pH, Biological Oxygen Demand (BOD), Suspended Solids (SS), Escherichia coli, Total Nitrogen (TN) and Total Phosphorus (TP) were considered as river water quality indica- tors. Satellite images were applied to generating the land use map. Multiple regression model was applied to linking the changes in the river water quality with the land uses in both entire catchment area and buffer zone. The results in- dicate that the integrative application of land use data from the entire catchment and the buffer zone could give rise to more robust model to predict the concentrations of Suspended Solids (r2=0.88) and Total Nitrogen (r2=0.90), rather than models which separately considered land use data in catchment and buffer zone.

Preservation Potentials of Essential Oils of Ocimum basilicum and Ocimum gratissimum from Two Agro-Ecological Zones on Freshwater Smoke-Dried Oreochromis niloticus Fish Sold in Some Local Markets in Cameroon

Dried fish are susceptible to bacteria and fungi attack and are liable to chemical changes which cause losses in quality and reduction of shelf-life. It is important therefore to maintain the quality of fish because continuous consumption of contaminated fish and their products may predispose consumers to health hazards. Maintenance of high quality fish therefore calls for adequate and effective preservation techniques. The study examined the effectiveness of essential oils of Ocimum basilicum and Ocimum gratissimum from two Agro-ecological zones of Cameroon in limiting the microbial proliferation and preserving the quality of smoke-dried Oreochromis niloticus fish stored at 25˚C for two months. The plant materials were harvested from the Western Highlands and Monomodal Humid Forest agroecological zones of Cameroon. Extraction of the essential oil from the plants was done by hydro-distillation. The fish species (Oreochromis niloticus) used in this study was chosen based on a survey study on the most consumed species of freshwater smoke-dried fish in the Western Highlands and Monomodal Humid Forest Agro-ecological zones of Cameroon. Heterotrophic bacteria counts, fungi counts and Enterobacteriaceae counts were used to assess the level heterotrophic bacteria, fungi and Enterobacteriaceae respectively in the fish samples during storage and were done by culture techniques using total plate count agar, potato dextrose agar and violet red bile glucose agar respectively. Total volatile basic nitrogen, peroxide value, and thiobarbituric acid reactive substance assays were used as spoilage indices to assess the nutritional quality of the fish during storage. From the survey study, Oreochromis niloticus was the most consumed smoke-dried fish in the Western Highlands (35.45%) and Monomodal Humid Forest (34.55%) agroecological zones. All the EOs caused a significant reduction in the microbial loads, total volatile basic nitrogen, peroxide value, and thiobarbituric acid reactive substance of smoke-dried Oreochromis niloticus as storage progressed. However, the reduction in these values was more pronounced in samples treated with essential oils of O. gratissimum from the Western Highlands, with heterotrophic bacteria, fungi and Enterobacteriaceae counts being 5.89, 6.97 and 4.59 log10 cfu/g respectively at the end of the storage period. This was followed by essential oils of O. gratissimum from the Monomodal Humid Forest with heterotrophic bacteria, fungi and Enterobacteriaceae counts being 6.11, 7.79 and 4.86 log10 cfu/g respectively at the end of the storage period. Also, essential oils of O. gratissimum from the Western Highlands was more effective in preserving the fish quality as lowest total volatile basic nitrogen (12.29 mg/100g), peroxide value (2.79 mEq O2·Kg−1) and thiobabituric reactive substance (1.695 mg MDA/Kg) values were observed for fish samples treated with this extract at the end of the storage period. This was followed by essential oils of O. gratissimum from the Monomodal Humid Forest with total volatile basic nitrogen (14.95 mgN/100g), Peroxide value (3.23 mEq O2·Kg−1) and thiobabituric reactive substance (2.354 mg MDA/Kg) at the end of the storage period. From the results obtained, essential oils from O. gratissimum were more effective than that from O. basilicum in the two agroecological zones and should be considered as natural alternative to chemical preservatives for further application in food preservation.

Chemical characteristics and water stability evaluation of groundwater in the CKDu Zone of Sri Lanka

Groundwater is the main source of drinking water for the rural population in the chronic kidney disease of unknown etiology(CKDu)zone of the North Central Province(NCP)in Sri Lanka.In this study,a total of 334 groundwater samples(311 dug wells,21 tube wells and 2 springs)during the wet season from two aquifers in the NCP were collected,and inves-tigated their chemical characteristics and evaluate their water quality,including ground-water chemistry,main ion sources,the corrosion and scaling potential of groundwater.The results showed that the two hydrochemical types of groundwater in the NCP were mainly of the Ca-HCO_(3),Na·Ca-HCO_(3)types,with the main HCO_(3)−,Na^(+)and Ca^(2+)ions in both types of groundwater originating from silicate and evaporite salt dissolution and influenced by alternating cation adsorption,while the presence of NO_(3)−was mainly anthropogenic.Eval-uation ofwater stability using namely Langelier saturation index(LSI),Ryznar stability index(RSI),Puckorius scaling index(PSI)and Larson-Skold index(LS),indicated that most ground-water presents corrosion potential and has corrosion behavior tendency of metals to some degrees.The water quality of Polonnaruwa was better than that of Anuradhapura in the NCP,and when the groundwater was worse than the“good”grade,which must be properly treated before it is used as drinking water.

Assessment of CO_(2)storage prospect based on physical properties of Rio Bonito Formation rock units

The physical properties of the rock units associated with the Rio Bonito Formation are presented in this study with the focus on modelling reservoir quality based on petrophysics-derived parameters to evaluate CO_(2)storage potentials.It involves the modelling of the reservoir depths,thicknesses,flow zone indicators(FZI),and effective permeability(Keff)and presenting the CO_(2)storage efficiency factors peculiar to the rock units of the study location.Research results presented by this study for the stated objectives are not quite common in the region.Keff values range from 200 mD to higher than 2000 mD,and FZI values are generally above 1.0 mm and up to 13.0 mm within the portions covered by the drilled wells.The sandstone units recorded are up to 20 m thick in some cases.The Keff and FZI models indicate the sandstone reservoirs as permeable units to support the injection and circulation of CO_(2)within the potential reservoir units of the Rio Bonio Formation across São Paulo State.Apart from some points in the southeastern part of the study location,where the Rio Bonito are delineated at depths less than 800 m(minimum CO_(2)storage depth based on best practices),other portions are deeper,ranging from 950 m to 3500 m.Thin-bedded layers will affect the integrity of the rocks as CO_(2)storage tanks or reservoir seals/traps/overburden within the region.Sandstone bed thicknesses are up to 20 m in some cases.However,hybrid CO_(2)reservoir units are feasible,especially in portions where thin siltstone layers are sandwiched between sandstone units to provide considerable thicknesses based on CO_(2)storage standards.The current study shows that useable areas considering reservoir thickness,depth,and other physical qualities will significantly control the CO_(2)storage efficiency of the study location.Further studies featuring a detailed geophysical exploration of the site to confirm the availability and saturations of preexisting fluid(hydrocarbon and water)are encouraged to boost CO_(2)storage in the region.The related research-based results,as mentioned above,may be combined with the results of this research to determine the area's potentials for CO_(2)storage or hydrocarbon production with CO_(2)storage options.

Mixing Zone Guidelines Application in a Smelter in Northern Sweden with Discharge to the Baltic Sea

This pilot study intended to investigate the application of Mixing Zone Guidelines in northern Sweden. The EC （European Commission）-Mixing Zone Guidelines were applied to seven effluent discharges. The effluents were from industrial processes used in the Ronnskar smelter, in northern Sweden. Each outlet in the smelter area discharges water into the Bothnian bay of the Baltic Sea. Cadmium （Cd）, mercury （Hg）, nickel （Ni） and lead （Pb） were the primary substances present in the effluents. A ＂Tiered Approach＂ was followed for mixing zone assessments in each of the discharge points. Discharge Test was used at Tier 2 and CORMIX （Cornell Mixing Zone Expert System model）, version 7, at Tier 3. At each discharge point, the AA-EQS （annual average-environmental quality standard） for each metal was met within a distance of 500 m from the outfalls. This distance was exceeded to meet the MAC-EQS （maximum allowable concentration-environmental quality standard） criteria at points 1 and 3 for total Hg concentrations. However, for the proper application of Mixing Zone Guidelines, a version of the Discharge Test for coastal waters should be developed and used. The decision at which tier the dissolved metal concentration should be compared with EQS values could depend on the effluent characteristics. For Swedish coastal waters, some consideration should be given to the background concentration of metals.

Agriculture and Water Sources Protection Zones in the Czech Republic

The area of interest is located in the South Moravia Region at the confluence of the Jihlava, Oslava and Rokytn^i rivers. Ivan^ice spring area comprises a series of hydrologic boreholes, it is the main water source for water supply of Ivan^ice and Rosice towns and provides water for 30,000 inhabitants. The risk analysis was created on the basis of water quality monitoring, hydrogeological assessment and terrain exploration and a revision of protection zones was proposed. The spring area is situated in nitrate vulnerable zones and recently nitrate concentrations have been decreasing. Water quality evaluation results： high concentration of manganese and iron, sometimes higher concentration of ammonium and COD. This area is intensively used for agriculture and it is necessary to make a compromise solution during protection zones proposal, The regime in protection zones can not affect manganese and iron concentration （their origin is in the natural geological environment）. Therefore, water treatment plant is in operation and its modernization is proposed. Furthermore, the paper deals with spring area intensification construction of a new hydrologic borehole, and managed and unmanaged infiltration of surface water. The proposal of protection zones revision consists of reduction to a 2nd level protection zone.

Digestive tract reconstruction using isoperistaltic jejunumlater-cut overlap method after totally laparoscopic total gastrectomy for gastric cancer: Short-term outcomes and impact on quality of life

AIM To evaluate the short-term outcomes and quality of life(Qo L) in gastric cancer patients undergoing digestive tract construction using the isoperistaltic jejunum-latercut overlap method(IJOM) after totally laparoscopic total gastrectomy(TLTG).METHODS A total of 507 patients who underwent laparoscopic gastrectomy(D2) from January 2014 to March 2016 were originally included in the study. The patients were divided into two groups to undergo digestive tract construction using either IJOM after TLTG(group T, n = 51) or Roux-en-Y anastomosis after laparoscopic-assisted total gastrectomy(LATG)(group A, n = 456). The short-term outcomes and Qo L were compared between the two groups after 1:2 propensity-score matching(PSM). We used a questionnaire to assess Qo L.RESULTS Before matching, age, sex, tumor size, tumor location, preoperative albumin and blood loss were significantly different between the two groups(P < 0.05). After PSM, the patients were well balanced in terms of their clinicopathological characteristics, although both blood loss and in-hospital postoperative days in group T were significantly lower than those in group A(P < 0.05). After matching, group T reported better Qo L in the domains of pain and dysphagia. Among the items evaluating pain and dysphagia, group T tended to report better Qo L("Have you felt pain" and "Have you had difficulty eating solid food")(P < 0.05).CONCLUSION The IJOM for digestive tract reconstruction after TLTG is associated with reduced blood loss and less pain and dysphagia, thus improving Qo L after laparoscopic gastrectomy.

Design of environmental decision support system and its application to water quality management

EDSS is a comprehensive software system for water quality management in tidal river networks in general and for the Pearl River Delta in particular. Its purpose is to provide a practical tool that could assist government agencies in decision making for the efficient management of water resources in terms of both quantity and quality. By combining the capabilities of geographical information system (GIS), database management system (DBMS), model base management system (MBMS) and expert system, the aim is to improve the quality of decision making in what is becoming an increasingly complex area. This paper first outlines the basic concepts and philosophy adopted in developing EDSS, the system architecture, design features, implementation techniques and facilities provided. Thereafter, the core part of the system—the hydrodynamic and water quality models are described briefly. The final contribution in this paper describes the application of EDSS to the Pearl River Delta, which has the most complicated tidal river network patterns as well as the fastest economic development in the world. Examples are given of the real-world problems that can be addressed using the system, including cross-boundary water pollution analysis, regional drinking water take-up site selection, screening of important polluters, environmental impact assessment, and water quality zoning and planning. It is illustrated that EDSS can provide efficient and scientific analytical tools for planning and decision-making purposes in the information era.

Intellectual Property Protection and High-quality Development of Cotton Industry in Xinjiang

This paper firstly introduces the general situation of cotton planting areas in China and cotton industry in Xinjiang,and the current situation of intellectual property protection of Xinjiang's cotton industry.Then,it analyzes the main problems in its intellectual property protection and high-quality development.On this basis,it comes up with the recommendations for high-quality development of cotton industry in Xinjiang under the strategy of strengthening the country with intellectual property.The recommendations include improving the level of creation of creative intellectual property rights,building an intellectual property rule system in the entire cotton industry chain in Xinjiang,building protected zones for production of major high quality agricultural product cotton,establishing a demonstration zone to undertake the transfer of the domestic cotton textile and garment industry,undertaking education on the sense of community for the Chinese nation in response to the Xinjiang cotton incident,and developing the"Belt and Road"blue market for Xinjiang cotton and its products.

Quick Single Run Capillary Zone Electrophoresis Determination of Active Ingredients and Preservatives in Pharmaceutical Products

The paper deals with the development of a rapid and efficient Capillary Zone Electrophoresis (CZE) method for Quality Control analysis of pharmaceutical preparations containing antihistamines, decongestants, anticholinergic remedies and preservatives. Active ingredients of interest are: ChlorPheniramine Maleate (CPM), DiPhenhydramine Hydrochloride (DPH), Ephedrine hydrochloride (E), Isopropamide Iodide (II), Pheniramine Maleate (PM), Lidocaine hydrochloride (L), Tetracaine hydrochloride (T), Clopamide Hydrochloride (CH), DiHydroErgochristine (DHE), PhenylEphrine hydrochloride (PE) and Acetaminophen (A). Preservatives studied are: MethylParaben (MeP), EthylParaben (EtP), PropylParaben (PrP), ButylParaben (BuP), p-HydroxyBenzoic Acid (p-HBA). All these analytes were separated in a single run using 60 mM tetraborate buffer solution (TBS) pH = 9.2 as a BackGround Electrolyte (BGE) by using an uncoated fused silica capillary of I.D. = 50 mm and applying a voltage of 25 kV in the first part of the electropheretic run (up to 5.8 min) and 30 kV for the remaining time. The hydrodynamic pressurization of the inlet vial was 20 psi at 7.2 min. up to the end of analysis. Total separation time was of 7.5 min. The method was then successfully validated and applied to the simultaneous determination of active ingredients and preservatives. Good repeatability, linearity, and sensitivity were demonstrated. Precision of migration time (tm) was RSD% < 0.53% and of corrected peak area (Ac) was RSD% < 6.15%. The linearity evaluation gave 0.9928 2 1.000. LOD and LOQ, accuracy (recovery) and ruggedness were evaluated for each analyte demonstrating the good reliability of the method. Analyses of some pharmaceutical real samples were performed.