Adaptive H_∞ Synchronization of Master-slave Systems with Mixed Time-varying Delays and Nonlinear Perturbations: An LMI Approach

This paper proposes an adaptive synchronization problem for the master and slave structure of linear systems with nonlinear perturbations and mixed time-varying delays comprising different discrete and distributed time delays. Using an appropriate Lyapunov-Krasovskii functional, some delay-dependent sufficient conditions and an adaptation law including the master-slave parame- ters are established for designing a delayed synchronization law in terms of linear matrix inequalities（LMIs）. The time-varying controller guarantees the H ∞ synchronization of the two coupled master and slave systems regardless of their initial states. Particularly, it is shown that the synchronization speed can be controlled by adjusting the updated gain of the synchronization signal. Two numerical examples are given to demonstrate the effectiveness of the method.

Distributed Generation Islanding Effect on Distribution Networks and End User Loads Using the Master-Slave Islanding Method

This study aims to address the feasibility of planned islanding operation and to investigate the effect of unplanned islanding using the master-slave islanding method for controlling the distributed generation units during grid-connected and islanding operation. Neplan desktop power simulation tool was used for the modelling and simulation of a realistic MV network with four different distributed generation technologies (diesel, gas, hydro and wind) along with their excitation and governor control systems, while an exponential model was used to represent the loads in the network. The dynamic and steady state behavior of the four distributed generation technologies were investigated during grid-connected operation and two transition modes to the islanding situation, planned and unplanned. The obtained results that validated through various case studies have shown that a suitable planned islanding transition could provide support to critical loads at the event of electricity utility outages.

Achievement of chaotic synchronization trajectories of master-slave manipulators with feedback control strategy

This paper addresses a master-slave synchro- nization strategy for complex dynamic systems based on feedback control. This strategy is applied to 3-DOF pla- nar manipulators in order to obtain synchronization in such complicated as chaotic motions of end-effectors. A chaotic curve is selected from Duffing equation as the trajectory of master end-effector and a piecewise approximation method is proposed to accurately represent this chaotic trajectory of end-effectors. The dynamical equations of master-slave manipulators with synchronization controller are derived, and the Lyapunov stability theory is used to determine the stability of this controlled synchronization system. In numer- ical experiments, the synchronous motions of end-effectors as well as three joint angles and torques of master-slave manipulators are studied under the control of the proposed synchronization strategy. It is found that the positive gain matrix affects the implementation of synchronization con- trol strategy. This synchronization control strategy proves the synchronization＇s feasibility and controllability for com- plicated motions generated by master-slave manipulators.

Exponential networked synchronization of master-slave chaotic systems with timevarying communication topologies

The networked synchronization problem of a class of master-slave chaotic systems with time-varying communication topologies is investigated in this paper. Based on algebraic graph theory and matrix theory, a simple linear state feedback controller is designed to synchronize the master chaotic system and the slave chaotic systems with a time- varying communication topology connection. The exponential stability of the closed-loop networked synchronization error system is guaranteed by applying Lyapunov stability theory. The derived novel criteria are in the form of linear matrix inequalities （LMIs）, which are easy to examine and tremendously reduce the computation burden from the feedback matrices. This paper provides an alternative networked secure communication scheme which can be extended conveniently. An illustrative example is given to demonstrate the effectiveness of the proposed networked synchronization method.

一种EtherCAT主站存取网络结构设计

针对EtherCAT主站存储和读取网络结构信息较为复杂的问题,设计一种先将网络结构信息与源代码分离,之后再将这些信息集成到可执行程序文件内部的方法。该方法在网络设计阶段通过配置软件将从站型号信息、型号索引、设备选型信息保存为文本文件;在软件构建阶段将上述文件与源代码一并处理生成程序;程序运行后通过型号索引直接寻址查询到设计方案中从站的ID,通过ID、从站数量对比实际部署的网络结构与所设计的方案是否一致。经测试验证,程序中存储的从站型号信息、型号索引及从站选型信息完整正确;在线检查网络结构功能可高效查询到方案中每个节点的型号信息并对比型号是否匹配。该方法实现简单且运行高效,有效降低主站和配套的网络结构设计工具的开发难度,同时改善了EtherCAT主站产品的用户体验和经济效益。

Hierarchical hybrid control network design based on LON and master-slave RS-422/485 protocol

Aiming at the weaknesses of LON bus, combining the coexistence of fieldbus and DCS (Distribu ted Control Systems) in control networks, the authors introduce a hierarchical hybrid control network design based on LON and master slave RS 422/485 protocol. This design adopts LON as the trunk, master slave RS 422/485 control networks are connected to LON as special subnets by dedicated gateways. It is an implementation method for isomerous control network integration. Data management is ranked according to real time requirements for different network data. The core components, such as control network nodes, router and gateway, are detailed in the paper. The design utilizes both communication advantage of LonWorks technology and the more powerful control ability of universal MCUs or PLCs, thus it greatly increases system response speed and performance cost ratio.

Content Addressable Memory Using Automatic Charge Balancing with Self-Control Mechanism and Master-Slave Match Line Design

Content Addressable Memory (CAM) is a type of memory used for high-speed search applications. Due to parallel comparison feature, the CAM memory leads to large power consumption which is caused by frequent pre-charge or discharge of match line. In this paper, CAM for automatic charge balancing with self-control mechanism is proposed to control the voltage swing of ML for reducing the power consumption of CAM. Another technique to reduce the power dissipation is to use MSML, it combines the master-slave architecture with charge minimization technique. Unlike the conventional design, only one match line (ML) is used, whereas in Master-Slave Match Line (MSML) one master ML and several slave MLs are used to reduce the power dissipation in CAM caused by match lines (MLs). Theoretically, the match line (ML) reduces the power consumption up to 50% which is independent of search and match case. The simulation results using Cadence tool of MSML show the reduced power consumption in CAM and modified CAM cell.

Master/Slave结构下可保证边竞争QoS限制的资源分配策略

任务调度作为分布式系统中提高系统并发处理的关键一直受到很多关注,随着分布式系统规模的扩大以及分布式系统中所处理任务数的增多,这个NP问题很多只能依靠启发式搜索技术获得近似最优解,然而这些算法中大都忽略了分布式系统中的一些实际问题,如通信竞争问题。已有的关注通信竞争的理论要么不适用于多任务的实时分布式系统,要么最终的任务分配无法实现整体makespan值最小(min-max)。本文提出了一个以master/slave为支撑结构,以最小化系统整体响应时间为代价函数的算术模型MMP。MMP既考虑了通信竞争问题,也考虑了多任务事实分布式系统的特征:任务数量多,任务间相互独立,任务以一定频率到达,任务执行受QoS限制。

基于Master/Slave模式的CT同时代数重建的并行进程

Mastel/Slave模式,又称主从模式,是一种并行程序设计思想。本文介绍了同时代数重建法(SimultaneousAlgebraicReconstructionTechnique,SART),并简化、改进了该算法:讨论了SART算法的并行性和基于Master/Slave模式的并行进程:通过算法复杂度分析和在以客户/服务器((Cient/Serve)模式组建的局域网上的网络并行重建试验,证明了该并行进程能较大地提高SART算法的时间效率。

Master-slave robot force telepresence technology

In order to make the manipulators useful, some force feedback is required to enable the operator to sense the robot’s feelings. Without force feedback, many tasks will not be able to be carried out. For these reasons, a master slave system with different kinematics has been developed. The system permits us to vary the ratio of the position/attitude, to design a master manipulator without considering the kinematics of the slave manipulator, and so on. To overcome the difficulties, a master slave manipulator system with different kinematics is proposed. The master manipulator is force controlled via a force torque sensor in the handle. As to master slave manipulator system with two way force feedback is concerned, the force goes to the actuator from the operator, and come back to the operator from the actuator. The working situation is viewed by the stereo TV supervisory system. The force and vision telepresence are thus achieved. In order to ensure the maneuverability, direct drive DC motors and PWM servo units are adopted to improve the response speed. It can provide force response in a wide range. A lot of experiments were performed with the master slave manipulator system force telepresence to study the force response under restricted environment. By two force sensors, the force position bilateral force response system effectively decreases the affection of friction and inertia force, and increases the authenticity of bilateral force response. When the slave manipulator arm is encountered with soft object(sponge), in the experiments, the operator can clearly have the fine feeling as if he himself is contacted with the object.

Research on A Master - slave Multi - microcomputers Control System for Hollow Spindle Fancy Yarn Spinning Machine

In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.

PHASE AND FREQUENCY LOCKING OF MICROWAVE AND MILLIMETER WAVE POWER COMBINING

The phase and frequency locking of microwave, millimeter wave power combining were analysed and summarized in an all-round way. The master/slave phase locking of cavity oscillators, the peer phase locking of mutually coupled oscillators, and the peer phase locking of ring-connected multiple oscillators were investigated. The results of numerical calculations, and the relations of phase to phase locking model and oscillator parameters were given. And the cavity and space power combining aspects for microwave and millimeter wave were presented.

THE DESIGN OF VMEBUS BRIDGE CONTROLLER WITH SHARC BUS

Targeting at the high expense and inflexibility to realize VMEbus bridge controller by professional Integrated Circuit (IC), this paper presents a scheme of adopting CPLD/FPGA (Complicated Programmable Logic Device/Field Programmable Gate Array) to design bridge controller between VMEbus and local bus. SHARC DSP (Digital Signal Processor) bus is an example. It has functions of nearly entire master/slave interface of VMEbus, and can act as DMA (Direct Memory Access) controller and perform block transfer in DMA or master processor initiative way without length limit. External circuit of the design is very simple. In comparison with special ICs, it has high performance to price ratio and can be easily applied to local buses of other processors with quite a little modification.

Power-combining based on master-slave injection-locking magnetron

A microwave power-combining system composed of two Panasonic 2M244-M1 magnetrons based on master–slave injection-locking is demonstrated in this paper. The principle of master–slave injection-locking and the locking condition are theoretical analyzed. Experimental results are consistent with the theoretical analysis and the experimental combined efficiency is higher than 96%. Compared with the external-injection-locked system, the power-combining based on the master–slave injection-locking magnetron is superior by taking out the external solid-state driver and the real-time phase control system. Thus, this power-combining system has great potential for obtaining a high efficiency, high stability, low cost, and high power microwave source.

Research on Master-slave Telerobot Force Telepresence Technology

A 3 DOF master-slave telerobot system is established for study on force telepresence technology. A force feedback and position control scheme is adopted in the bilateral force response control system,and force fidelity and controllability experiments demonstrate feasibility of the con-trol system.

Tremor suppression in master-slave robot remote welding system

Welding seam tracking precision was decreased due to human hand tremor during the master-slave welding teleoperation. To solve this problem, a master-slave robot remote welding system was built, the system consisted of a master manipulator with six degree of freedom （ DOF ） , an industrial computer control system and a slave Motoman HP3 J robot, and human hand tremor and digital filtering were discussed. An optimal digital filter was designed to clean human tremor signal for improving the welding seam tracking precision. The experimental results show that the digital filter suppresses the operator＇ s tremor signal.

Design of the Measuring Instrument to the liquid level Based on MSP430 SCM

This paper introduced the components, principle and the hardware and software design of the multiplexing measuring and control instrument to the liquid level that is based on MSP430 SCM. This system is made of pressure sensor, signal processing circuit, electromagnetic valve, output driving circuit, Chinese character LCD, keyboard, optic alarm circuit and MSP430MCU, and realized Liquid level automatic monitor, out range alarm and online function.

智能算法的亚群优化策略综述

群智能算法的优化是提升群智能算法性能的一个主要途径,随着群智能算法越来越广泛地运用到各类模型优化、生产调度、路径规划等问题中,对智能算法性能的要求也越来越高。亚群策略作为一种优化群智能算法的重要手段,能够灵活地平衡算法的全局勘探能力和局部开发能力,已经成为群智能算法的研究热点之一。为了促进亚群优化策略的发展和应用,对动态亚群策略、基于主从范式的亚群策略和基于网络结构的亚群策略进行了详细调查,阐述了各类亚群策略的结构特点、改进方式和应用场景。最后,总结了亚群策略目前存在的问题以及未来的研究趋势和发展方向。

基于纳什谈判和主从博弈的多园区综合能源系统优化调度

为充分考虑多园区综合能源系统(MCIES)中多利益主体间交易合作与多种能量间的耦合关系,提出了1种基于纳什谈判-主从博弈的点对点分布式交易策略。首先,建立考虑综合需求响应的MCIES主从博弈动态定价模型,以园区综合能源系统(CIES)运营商作为领导者,给下层用户制定动态电价与热价,用户响应电价与热价进行综合需求响应,CIES运营商根据用户的需求响应计划调整机组出力;其次,基于纳什谈判理论,建立包含主从博弈动态定价机制与CIES间合作博弈的MCIES双层优化模型;然后,将原问题等效为MCIES收益最大化子问题和合作收益分配最大化子问题,采用交替方向乘子法(ADMM)对模型进行求解。最后,仿真结果表明所提策略可实现CIES联盟利润的最大化,并合理分配收益,同时最小化用户用能成本。

基于切换系统的独立微电网稳定控制设计

独立微电网是一个复杂的非线性系统,为解决典型光储柴独立微电网在能源约束下存在控制单元切换的问题,提出将非线性切换系统理论应用到主从控制下的主控单元切换问题上。首先,当主从控制下的储能系统和柴油发电机分别作为主控单元时,将它们视为两个子系统,建立非线性切换系统模型。然后,应用多Lyapunov函数法分析切换系统的稳定性,同时利用backstepping方法分别设计子系统的非线性控制器,保留系统的非线性特征。最后,采用美国国家能源实验室开发的仿真软件中的硬充电策略作为切换策略,保证切换过程中系统的稳定性。通过MATLAB仿真证明了所设计方法的有效性。