Review of research on high-speed railway subgrade settlement in soft soil area

Construction issues of high-speed rail infrastructures have been increasingly concerned worldwide,of which the subgrade settlement in soft soil area becomes a particularly critical problem.Due to the high compressibility and low permeability of soft soil,the post-construction settlement of the subgrade is extremely difficult to control in these regions,which seriously threatens the operation safety of high-speed trains.In this work,the significant issues of high-speed railway subgrades in soft soil regions are discussed.The theoretical and experimental studies on foundation treatment methods for ballasted and ballastless tracks are reviewed.The settlement evolution and the settlement control effect of different treatment methods are highlighted.Control technologies of subgrade differential settlement are subsequently briefly presented.Settlement calculation algorithms of foundations reinforced by different treatment methods are discussed in detail.The defects of existing prediction methods and the challenges faced in their practical applications are analyzed.Furthermore,the guidance on future improvement in control theories and technologies of subgrade settlement for high-speed railway lines and the corresponding challenges are provided.

Pile-soil stress ratio in bidirectionally reinforced composite ground by considering soil arching effect

To discuss the soil arching effect on the load transferring model and sharing ratios by the piles and inter-pile subsoil in the bidirectionally reinforced composite ground, the forming mechanism, mechanical behavior and its effect factors were discussed in detail. Then, the unified strength theory was introduced to set up the elastoplastic equilibrium differential equation of the subsoil under the limit equilibrium state. And from the equation, the solutions were derived with the corresponding formulas presented to calculate the earth pressure over and beneath the horizontal reinforced cushion or pillow, the stress of inter-pile subsoil and the pile-soil stress ratio. Based on the obtained solutions and measured data from an engineering project, the influence rules by the soil property parameters (i.e., the cohesion c and internal friction angle φ) and pile spacing on the pile-soil stress ratio n were discussed respectively. The results show that to improve the load sharing ratio by the piles, the more effective means for filling materials with a larger value of φ is to increase the ratio of pile cap size to spacing, while to reduce the pile spacing properly and increase the value of cohesion c is advisable for those filling materials with a smaller value of φ.

Concrete-Filled Steel Tube Arch Bridges in China

In the past 20 years, great progress has been achieved in China in the construction of concrete-filled steel tube （CFST） arch bridges and concrete arch bridges with a CFST skeleton. The span of these bridges has been increasing rapidly, which is rare in the history of bridge development. The large-scale construction of expressways and high-speed railways demands the development of long-span arch bridges, and advances in design and construction techniques have made it possible to construct such bridges. In the present study, the current status, development, and major innovative technologies of CFST arch bridges and concrete arch bridges with a CFST skeleton in China are elaborated. This paper covers the key con- struction technologies of CFST arch bridges, such as the design, manufacture, and installation of steel tube arch trusses, the preparation and pouring of in-tube concrete, and the construction of the world＇s longest CFST arch bridge-the First Hejiang Yangtze River Bridge. The main construction technologies of rein- forced concrete arch bridges are also presented, which include cable-stayed fastening-hanging cantilever assembly, adjusting the load by means of stay cables, surrounding the concrete for arch rib pouring, and so forth. In addition, the construction of two CFST skeleton concrete arch bridges-the Guangxi Yongning Yong River Bridge and the Yunnan-Guangxi Railway Nanpan River Bridge--is discussed. CFST arch bridges in China have already gained a world-leading position; with the continuous innovation of key technologies, China will become the new leader in promoting the development of arch bridges.

Earth Pressure of the Trapdoor Problem Using Three-Dimensional Discrete Element Method

Load transformation from the yielding part of the soil to the adjacent part is known as the soil arching effect,which plays an important role in the design of various geotechnical infrastructures.Terzaghi’s trapdoor test was an importantmilestone in the development of theories on soil arching.The research on earth pressure of the trapdoor problem is presented in this paper using the three-dimensional(3D)discrete element method(DEM).Five 3D trapdoor models with different heights are established by 3DDEMsoftware PFC 3D.The variation of earth pressure on the trapdoor with the downward movement of the trapdoor,the distribution of vertical earth pressure along the horizontal direction,the distribution of vertical earth pressure along the vertical direction,the distribution of lateral earth pressure coefficient along the depth direction,the magnitude and direction of contact force chain are studied,respectively.Related research results show that the earth pressure on the trapdoor decreases rapidly after the downward movement of the trapdoor,and then reaches the minimum earth pressure.After that,the earth’s pressure will rise slightly,and whether this phenomenon occurs depends on the depth ratio.For the bottom soil,due to the stress transfer caused by the soil arching effect,the ratio of earth pressure in the loose area decreases,while the ratio of earth pressure in the stable area increases.With the trapdoor moving down,the vertical earth pressure along the depth in the stable zone is basically consistent with the initial state,which shows an approximate linear distribution.After the trapdoor moves down,the distribution of earth pressure along with the depth in the loose area changes,which is far less than the theoretical value of vertical earth pressure of its self-weight.Because of the compression of the soil on both sides,the lateral earth pressure coefficient of most areas on the central axis of the loose zone is close to the passive earth pressure coefficient Kp.The existence of a‘soil arch’can be observed intuitively from the distribution diagram of the contact force chain in the loose zone.

Numerical and theoretical analysis on soil arching effect of prefabricated piles as deep foundation pit supports

This study presents a detailed investigation into the soil arching effects within deep foundation pits(DFPs),focusing on their mechanical behavior and implications for structural design.Through rigorous 3D finite element modeling and parameter sensitivity analyses,the research explores the formation,geometric characteristics,and spatial distribution of soil arching phenomena.The investigation encompasses the influence of key parameters such as elastic modulus,cohesion,and internal friction angle on the soil arching effect.The findings reveal that soil arching within DFPs exhibits distinct spatial characteristics,with the prominent arch axis shifting as excavation depth progresses.Optimal soil arching is observed when the pile spacing approximates three times the pile diameter,enhancing soil retention and minimizing deformation risks.Sensitivity analyses highlight the significant impact of soil parameters on soil arching behavior,underscoring the critical role of cohesive forces and internal friction angles in shaping arching characteristics.By elucidating the interplay between soil parameters and soil arching effects,the research provides insights for optimizing pile spacing and structural stability.

Double aortic arch and nasogastric tubes: A fatal combination

Double aortic arch is a common form of complete vascular ring that encircles both the trachea and the esophagus, and presents with various respiratory and esophageal symptoms, usually in the pediatric population. We present a case of double aortic arch in an adult patient that manifested as massive upper gastrointestinal bleeding after prolonged nasogastric intubation.

Dynamic soil arching in piled embankment under train load of high-speed railways

Piled embankments have many advantages that have been applied in high-speed railway construction engineering.However,the load transfer mechanism of piled embankments,such as soil arching and tension membranes,is still unclear,especially under dynamic loads.To investigate the soil arching and tension membrane under dynamic train loads on high-speed railways,a large-scale piled embankment model test with X-shaped piles as vertical reinforcement was performed,in which twenty-eight earth pressure cells were installed in the piled embankment and an M-shaped wave was adopted to simulate the high-speed railway train load.The results show that dynamic soil arching only occurs when two bogies of a carriage pass by and disappears at other times.The dynamic soil arching and membrane effect are the most significant under the concrete base.The arching height,stress concentration ratio and pile-soil load sharing ratio have a minimal value at 25 Hz.The dynamic soil arching degrades severely at 25 Hz,whose height at 25 Hz is only 0.35 times that at 5 Hz.The arching height fluctuates over a narrow range with increasing loading amplitude.The stress concentration ratio and the pile-soil load sharing ratio increase monotonically as the loading amplitude increases.

A History of the Urban Underground Tunnel (4000 B.C.E. - 1900 C.E.)

Generally hidden from public view, out of our daily thoughts, and literally under our feet, are myriad urban underground tunnels that make our modern megacities possible. From their ancient beginnings in antiquity, as a means of supplying fresh water and draining waste water from cities, underground tunnels evolved into a means of providing high capacity rail mass transit in our most densely populated urban centers. This paper provides a broad overview of the evolution of urban tunnels across a 6000 year time span and includes the specific engineering formulas/computations for the earliest 19th century subways/infrastructure projects based on the Roman vaulted arch tunnel.

Analysis of Soil arching effect for Blind sheet-pile wharf based on ABAQUS

Combined with practical engineering, based on the introduction of soil arching theory, we explore the impact of barrier piles in blind sheet-pile bank connecting structure. Besides, we build a plane strain model by ABAQUS sot＇cware to study the impact of cross section type, the pile spacing and soil properties on soil arching effect. We find that cross section type of the pile has a certain influence on soil stress distribution in front of the barrier piles by comparing circular cross section and rectangular cross section. We also find that clear distance between the barrier piles and cohesive force of the soil have a great influence on that impact. We can increase clear distance between the barrier piles appropriately to improve the efficiency of construction and reduce the proiect cost.

Soil-structure interaction of unsymmetrical trench installation culvert

The computation of the design load on culverts in the current Chinese General Code for Design of Highway Bridges and Culverts （CGCDHBC）is primarily based on the linear earth pressure theory, which cannot accurately reflect the changes in vertical loads on trench installation culverts. So the changes in vertical earth pressure and soil arching effect in the backfill for an unsymmetrical trench installation culvert are studied based on a full scale experiment and finite element （FE） simulation. The variation laws of foundation pressure and settlement are also analyzed. Meanwhile, the influence of eccentric load induced by an unsymmetrical trench installation on the interaction of a soil- structure system is discussed. Results show that soil arch is formed when the backfill on the culvert reaches a certain height. It can relieve the earth pressure concentration on the crest of the culvert, but it is instable. The earth pressures obtained by full scale experiment and numerical simulation are greater than those calculated by the current CGCDHBC method. The eccentric load effect on the culvert has a significant influence on the stress states and deformation of the soil-structure system.

Visualization of the formation and features of soil arching within a piled embankment by discrete element method simulation

Piled embankments are widely used in highway and railway engineering due to their economy and efficiency inovercoming several issues encountered in constructing embankments over weak soils. Soil arching, caused by the pile-subsoilrelative displacement （△s）, plays an important role in reducing the embankment load falling on weak soil, however, the funda-mental characteristics （e.g., formation and features） of soil arching remain poorly understood. In this study, a series of discreteelement method （DEM） modellings are performed to study the formation and features of soil arching with the variation of As inpiled embankments with or without geosynthetic reinforcement. Firstly, calibration for the modelling parameters is carried out bycomparing the DEM results with the experimental data obtained from the existing literature. Secondly, the analysis of the macro-and micro-behaviours is performed in detail. Finally, a parametric study is conducted in an effort to identify the influences of threekey factors on soil arching： the friction coefficient of the embankment fill （f）, the embankment height （h）, and the pile clear spacing（s-a）. Numerical results indicate that △s is a key factor governing the formation and features of soil arching in embankments. Tobe specific, soil arching gradually evolves from two inclined shear planes at a small △s to a hemispherical arch at a relatively largeAs. Then, with a continuous increase in △s, the soil arching height gradually increases and finally approaches a constant value of0.8（s-a） （i.e., the maximum soil arching height）. For a given case, the higher the soil arching height, the greater the degree of soilarching effect. The parametric study shows that the friction coefficient of the embankment fill has a negligible influence on theformation and features of soil arching. However, embankment height is a key factor governing the formation and features of soilarching. In addition, pile clear spacing has a significant effect on the formation of soil arching, but not on its features.

Soil-cement mixture properties and design considerations for reinforced excavation

soil-cement is a mixture produced by grouting or mixing cement with soils. This paper reviews and discusses the general classifications of grouting techniques and the suitability of their applications.The mechanical properties of soil-cement mixture and the influence of sodium silicate added are discussed. Design considerations for deep soil mixed wall(DSMW) for excavation support and vault arch for tunnelling stabilisation are presented. Parameters for the numerical analysis of soil-cement mixture are evaluated and recommended.

Seismic behavior of concrete filled steel tubular arch structures

Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and Shanghai artificial wave were adopted as the input excitation. The entire test process can be divided into three stages depending on the lateral brace configurations, i.e., fully (five) braced, two braces removed, and all braces removed. A total of 46 tests, starting from the elastic state to failure condition, have been conducted. The natural vibration frequencies, responses of acceleration, displacement and strain were measured. From the test results, it is demonstrated that the CFT arch structures are capable of resisting severe ground motions and that CFT arches offer a credible alternative to reinforced concrete arches, especially in regions of high seismic intensity.

Settlement Mode Analysis for An Immersed Tube Tunnel Considering A Nonuniform Foundation Under Tidal Load

Immersed tube tunnels are usually placed on soft soil layers in cross-sea tunnelling engineering.Owing to the influence of stratum conditions and slope design,the longitudinal distribution of substratum layers is generally uneven.Thus,the inhomogeneous deformation of the element-joint becomes the key factor in the failure of the immersed tube tun-nel.Therefore,a corresponding calculation method for joint deformation is needed to explore the deformation law of immersed tube tunnels.By constructing a three-section immersed tube tunnel analysis model(TTM),the relationship between the two types of deformation of the immersed tube tunnel structure in a longitudinal nonuniform soft soil foundation is described,and the deformation characteristics of the immersed structure under different boundaries are discussed.Based on the mechanical behaviour of the joint and foundation,according to the Timoshenko beam on the Vlasov two-parameter foundation(VTM),considering the tidal cyclic load during the operation and maintenance period,an example analysis is given.Moreover,the deformation characteristics and development trend of the immersed tube tunnel under the influence of different soil layers are discussed.The obtained results have a certain guiding significance for the deformation calculation of immersed tube tunnels.

Model tests on interaction between soil and geosynthetics subjected to localized subsidence in landfills

In a landfill, excessive tensile strains or failure of the liner system due to localized subsidence underneath the geosynthetic liner, is a concern in design and operation of the landfill. The localized subsidence can be commonly withstood by reinforcements such as geogrids. A total of nine model tests were carried out to study the influence of soil arching in overburden sandy soil on the geosynthetics and the interaction between the soil and the geosynthetics. The localized subsidence was modeled by a strip trapdoor under the geosynthetic reinforcements. The reinforcement includes several layers of polyvinylchlorid （PVC） membrane or both PVC membrane and a compacted clay layer. Test results show that the vertical soil pressure acting on the geosynthetics within the subsidence zone is strongly related to the deflection of the geosynthefics. The soil pressure acting on the deflected geosynthetics will decrease to a minimum value with respect to its deflection if the final deflection is large enough, and this minimum value is almost independent of the overburden height. Otherwise, the deflection of geosynthetics cannot result in a full degree of soil arching, and the soil pressure within the subsidence zone increases with the increase of overburden height. Deflections and strains of the geosynthetics obviously decrease with the increase of their tensile stiffness. The presence of a compacted clay layer buffer can therefore reduce both deflections and strains of the geosynthetics. Finally, a composite liner structure is recommended for landfills to withstand the localized subsidences.

Improved method for determining active earth pressure considering arching effect and actual slip surface

To determine the distribution of active earth pressure on retaining walls, a series of model tests with the horizontally translating rigid walls are designed. Particle image velocimetry is used to study the movement and shear strain during the active failure of soil with height H and friction angle φ. The test results show that there are 3 stages of soil deformation under retaining wall translation: the initial stage, the expansion stage and the stability stage. The stable sliding surface in the model tests can be considered to be composed of two parts. Within the height range of 0.82 H-1.0 H, it is a plane at an angle of π/4+φ/2 to the horizontal plane. In the height range of 0-0.82 H, it is a curve between a logarithmic spiral and a plane at an angle of π/4+φ/2 to the horizontal. A new method applicable to any sliding surface is proposed for active earth pressure with the consideration of arching effect. The active earth pressure is computed with the actual shape of the slip surface and compared with model test data and with predictions obtained by existing methods. The comparison shows that predictions from the newly proposed method are more consistent with the measured data than the predictions from the other methods.

Centrifuge and numerical modeling of h-type anti-slide pile reinforced soil-rock mixture slope

Due to the loose structure,high porosity and high permeability of soil-rock mixture slope,the slope is unstable and may cause huge economic losses and casualties.The h-type anti-slide pile is regarded as an effective means to prevent the instability of soilrock mixture slope.In this paper,a centrifuge model test was conducted to investigate the stress distribution of the h-type anti-slide pile and the evolution process of soil arching during the loading.A numerical simulation model was built based on the similar relationship between the centrifuge model and the prototype to investigate the influence factors of the pile spacing,anchored depth,and crossbeam stiffness,and some recommendations were proposed for its application.The results show that the bending moment distribution of the rear pile exhibits Wshaped,while for the front pile,its distribution resembles V-shaped.The soil arching evolution process during loading is gradually dissipated from bottom to top and from far to near.During the loading,the change of bending moment can be divided into three stages,namely,the stabilization stage,the slow growth stage,and the rapid growth stage.In engineering projects,the recommended values of the pile spacing,anchored depth,and crossbeam stiffness are 4.0d,2.0d,and 2.0EI,where d and EI are the diameter and bending stiffness of the h-type anti-slide pile respectively.

Effects of Litter Removal and Addition on Soil Nitrogen Mineralization of Eucalyptus Plantation

[Objectives]This study was conducted to understand the process of soil nitrogen mineralization in Eucalyptus plantations,and to identify the characteristics of soil nitrogen mineralization with different litter inputs.[Methods]With the soil of the Eucalyptus plantation in Fusui County,Guangxi as the research object,the soil nitrogen mineralization of the Eucalyptus plantation under different litter treatments(removing litter,adding litter and retaining litter)was studied by PVC tube closed-top in-situ incubation.[Results]①After 1 year of litter treatment,the inorganic nitrogen(NH_(4)^(+)-N+NO_(3)^(-)-N)in the soil of different treatments ranked as adding litter(20.15 mg/kg)>retaining litter(16.02 mg/kg)>removing litter(11.60) mg/kg),and the differences reached a significant level(P<0.05).②After 30 d of in-situ incubation,there were significant differences in soil nitrate nitrogen content before and after incubation in the three treatments(removing litter,adding litter,and retaining litter)before and after incubation(P<0.05),but no significant differences were observed in soil ammonium nitrogen content(P>0.05).Soil nitrate nitrogen contents increased from 1.47,2.01 and 1.72 mg/kg before incubation to 3.66,6.73 and 5.02 mg/kg,respectively,and soil ammonium nitrogen content increased from 11.60,20.15 and 16.02 mg/kg before incubation to 13.65,21.54 and 17.18 mg/kg,respectively.The net nitrogen mineralization quantities of the three treatments were 4.24,6.11 and 4.46 mg/kg,respectively,and the net nitrogen mineralization rates from large to small were adding litter[0.180 mg/(kg·d)]>retaining litter[0.141 mg/(kg·d)]>removing litter[0.125 mg/(kg·d)].Therefore,both removal and addition of litter affected the soil nitrogen input and nitrogen mineralization rate of the Eucalyptus plantation,thereby affecting soil nitrogen availability and the ability of soil to maintain plant-available nitrogen.[Conclusions]This study provides a theoretical basis for nutrient management in Eucalyptus plantations,especially nitrogen nutrient management.

GC/MS: A Valid Tool for Soil Gas Hydrocarbons Speciation

This work describes an alternative method based on GC/MS technique with SCAN-ion approach for speciation of hydrocarbons contained in soil gas matrices and sampled on solid sorbent tubes (coconut shell charcoal).

Heavy Metals Accumulation in Soil Irrigated with Industrial Effluents of Gadoon Industrial Estate, Pakistan and Its Comparison with Fresh Water Irrigated Soil

Wastewater mixed with industrial effluents is used for irrigation in Gadoon Industrial estate and thus contaminating soil. This soil was tested for heavy metal content by using atomic absorption spectrophotometer (perkin elmer 700) and compared with control soil irrigated with tube well water at seven selected spots. Accumulation of the toxic metal was significantly greater in the soil irrigated with industrial effluent than control soil (p < 0.05). Manganese (Mn) was the most significant pollutant, accumulated up to 9.95 ppm in the soil irrigated with industrial waste water. It was found that the samples were containing Zn in the range of 1.596 - 6.288, Cu 0.202 - 1.236, Co 0.074 - 0.115, Ni 0.0002 - 0.544, Cr 0.243 - 0.936, Mn 3.667 - 9.955 and Pb 0.488 - 1.259 ppm. No sample was containing the heavy metal above the critical level mentioned in typical and unsafe heavy metal levels in soil.