DANIELI concepts and experiences in thin slab casting and rolling technology for HRC production—the evolution of a winning process route to face increasing market requirements

The direct rolling process for hot strip production,where the thin slab caster is connected directly to the mill,has gained market share rapidly because of its remarkable advantages in terms of energy savings and investment cost over the conventional hot strip mills. However,the unquestionable advantages of the first-generation applications of this plant concept also entail significant limitations both in productivity and steel grades that can be produced. Since his first pioneering applications,Danieli considered strategic the development of new technical solutions specifically conceived to overcome these limitations with the goal of increasing plant production volumes and enlarging steel grade product mix,in order to cover the gap between "Conventional mill" and "Thin slab casting and rolling" process routes. In order to reach this goal,Danieli has developed a complete portfolio of plant lay outs adopting Thin Slab Casting and Rolling technologies,each of them conceived to guarantee the optimal CAPEX and OPEX parameters in fitting with market requirements our Customer intend to target.in terms of productivity,steel grades and coil dimension product mix. Danieli TSR(Thin Slab Rolling) fTSR(flexible Thins Slab Rolling) QSP(Quality Strip Production) and ETR(Extra Thin Rolling) plant configurations are analyzed in this paper. With this diversified approach,Danieli solutions are most appropriate answers to thin slab casting and rolling to produce hot rolled coils with superior quality and an extremely diversified range of steel grades. Already,this approach has allowed Danieli plants to:①exceed the threshold production of 3.0 Mt/a with 2 casting strands in operation as done in Tangshan Iron and Steel plant in P.R.China since 2005;②expand the product mix to include virtually all the steel grades used for flat product applications,including the most demanding ones,such as peritectic(in Essar Algoma Canada and Benxi Iron and Steel,China),micro-alloyed,and silicon steels,for the most sophisticated applications,such as automotive and pipe manufacturing,including Arctic applications,(as done in OMK plant in Russia);③extend the range of final strip thicknesses to include ultra thin gauges,down to 0.8 mm(as in Ezz Flat Steel,in Egypt).

Solidification of horizontally continuous casting of super-thin slab in stable magnetic field and alternating current

The solidified structures of horizontally continuous casting（HCC） of super-thin slab and its relations with the current were studied under the electromagnetic vibration（EMV）.The results show that,under the action of the periodical forces from EMV,the solidified structures of the super-thin slab of pure tin is greatly refined,and the extent of grain refinement is increased with the magnitude of alternating current.For the Sn-10%Pb alloy,it is shown that the EMV promotes the growth of equiaxed grains in the center of super-thin slab,and the grains are refined with the alternating current increasing.This is useful to prevent some solidification defects in the horizontally continuous casting of super-thin slab,such as columnar grains butting,porosity,inclusions and gases gathering,and composition segregation in the centre of slab.

Morphology and Precipitation Kinetics of MnS in Low-Carbon Steel During Thin Slab Continuous Casting Process

The morphology of manganese sulfide formed during thin slab continuous casting process in low-carbon steel produced by compact strip production （CSP） technique was investigated. Using transmission electron microscopy analysis, it was seen that a majority of manganese sulfides precipitated at austenite grain boundaries, the morphologies of which were spherical or close to the spherical shape and the size of MnS precipitates ranged from 30 nm to 100 nm. A mathematical model of the manganese sulfide precipitation in this process was developed based on classical nucleation theory. Under the given conditions, the starting and finishing precipitation temperatures of MnS in the continuous casting thin slab of the studied low-carbon steel are 1 189 ℃ and 1 171 ℃, respectively, and the average diameter of MnS precipitates is about 48 nm within this precipitation temperature range. The influences of chemical components and thermo-mechanical processing conditions on the precipitation behavior of MnS in the same process were also discussed.

Effects of the width and thickness of slabs on broadening in continuous casting

A 3D viscoelastic-plastic thermal-mechanical coupled finite element model was built on the basis of the secondary development of the commercial software MSC.Marc. Numerical simulations were performed to study slab broadening in the secondary cooling zone. The effects of slab width and thickness on slab broadening were considered. The obtained results reveal that the width broadening is noticeable, and the ratio of ultimate broadening slightly increases with the increase of slab width. This agrees well with the measured data in practice. There is no obvious increase in ultimate broadening when the thickness of slabs increases.

INFLUENCES OF CASTING SPEED AND SEN DEPTH ON FLUID FLOW IN THE FUNNEL TYPE MOLD OF A THIN SLAB CASTER

In recent years, thin slab continuous casting technology has been widely used to improve the quality of the product and to reduce the cost. One of the challenges faced by this technology is to design reasonable flow patterns, which strongly affect the surface and inner properties of the final slab in the mold. With the fixed scales and complex geometrical structures of nozzle and funnel type mold, a series of numerical simulations are made to analyze the flow patterns in melt steel using finite volume method based on structured body fitted coordinate grids. The CFD （computational fluid dynamics） package is validated first using one typical case described in previously published studies, and then it is developed to study the effect of operational parameters on fluid flow in thin slab caster. Two operational parameters, casting speed and SEN （submerged entry nozzle） depth, are mainly considered for numerical analysis. On the basis of present simulations, the reasonable SEN submergence depths corresponding to different casting speeds are suggested according to fluid flow characteristics like, flow jet impingement on the narrow side of the mold, flow speed of the melt steel beneath the meniscus and the recirculation region. This is the first stage of study on the numerical analysis of the whole thin slab casting process with electromagnetic brake.

Modeling of unsteadiness of fluid flows and level fluctuations in thin slab continuous casting moulds

Unsteady fluid flows and level fluctuations in a thin slab continuous casting mould have significant influence on product quality. In this study, the phenomena concerning transient flow features and free surface motions were analyzed by means of the large eddy simulation （LES） software with the smagorinsky SGS model--VisualCast （VCast） II, where the Simpler algorithm on a body-fitted mesh was used to resolve governing equations. A series of water analog experiments on the fluid flow and the surface wave in the moulds of thin slab continuous casting were also performed. The results of fluid regions, middle of vortex and level fluctuation from digital simulations were identical with the results of the water analog experiments.

Technological Investigation on the Continuous Casting of Mid-Width Thin Slabs

Continuous casting of thin slabs is a key state project for 7th and sth five -year plans. On thebasis of foundamental works , CISRI condueted the tests of 102 heats in Lanzhou Steel Works in the periodof January 1991- June 1992. Three slab assortments of 50× 900 mm . 70 × 900 mm , 70 × 500 mm were ex-amined. In June of 1992, 412 t steel of 46 heats were cast with the efficiency of 91. 3 %. This. result meetsthe requiremeni of the state in this period. The mould, hedt transfer . casting technology and factors influ-encing slab’s qualities are investigated as well.

Temperature distribution and dynamic control of secondary cooling in slab continuous casting

To predict and optimize the temperature distribution of slab continuous casting in steady operational state, a three-dimensional model （named ＂offline model＂） based on the heat transfer and solidification theories was developed. Both heat transfer and flux distribution characteristics of the nozzle sprays on the slab were considered, and the complicated boundary conditions, such as spray cooling, natural convection, thermal radiation as well as contact cooling of individual rolls were involved in the model. By using the calibrated caster dependent model factors, the calculated temperature and shell thickness accorded well with the measured. Furthermore, a dynamic secondary water cooling control system was also developed on the basis of a two-dimensional transient heat transfer model （named ＂online model＂） and incremental PID control algorithm to reduce slab surface temperature fluctuation in unsteady state. Compared with the traditional spray table control method, the present online model and dynamic PID control demonstrate a higher capability and flexibility to adjust cooling water flowrate and reduce slab surface temperature fluctuation when the casting speed is changed.

Influence of roll speed difference on microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling process

The influences of the dissimilarity in the roll speeds on the microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling(CCCR) process were investigated. Several experiments were conducted with three different upper/lower roll rotational speed ratios(ω/ω0, ω is the upper roll rotational speed and ω0 is the lower roll rotational speed), namely 1:1, 1:1.2 and 1:1.4. It was found that the greatest dissimilarity in the roll speed(ω/ω0=1:1.4) improved the yield strength and ultimate tensile strength of 7075 Al plate in the rolling direction by 41.5% and 21.9%, respectively. Moreover, at a roll speed ratio of ω/ω0=1:1.4, the average grain size was decreased by 36% whereas the mean hardness of the transverse cross-section of the finally rolled plate was increased by about 9.2%. Texture studies also revealed that the more the difference in the roll speeds was, the greater the isotropy and the hardness of the final product were. Nevertheless, conducting CCCR operation with different roll speeds resulted in about 6% reduction in the elongation of the deformed plate.

STUDY OF DYNAMIC RECRYSTALLIZATION OF LOW CARBON STEEL IN THIN SLAB CONTINUOUS ROLLING PROCESS

Combined with the technological characteristics of thin slab continuous rolling process （TSCR）, dynamic recrystallization of an extremely coarse austenite of low carbon steel is studied by Thermecmaster-Z hot simulator. By the analysis of true stress-strain curves and the observation of microstructures at different deformation stages, the critical stress and critical strain are determined under different deformation conditions. The effect of Z parameter on dynamic recrystallization of coarse austenite is studied. The microstructure evolution in real production is also discussed.

INVESTIGATION ON HOT DUCTILITY AND STRENGTH OF CONTINUOUS CASTING SLAB FOR AH32 STEEL

By means of Gleeble-1500 testing machine, the simulation of continuous casting process forAH32 steel was carried out and hot ductility and strength were determined. The cracking sensitivity was studied under the different temperatures and strain rates. The Precipitations of AIN at different temperatures and the fractures of high-temperature tensile samples were observed by using TEM （transmission electron microscope） and SEM （scanning electron microscope）. The factors affecting the brittle temperature zone were discussed.

Microstructure evolution and mechanical properties of Cu-0.36Be-0.46Co alloy fabricated by heating-cooling combined mold horizontal continuous casting during cold rolling

Cu-0.36 wt.%Be-0.46 wt.%Co alloy plate with 300 mm in width and 10 mm in thickness prepared by heating-cooling combined mold(HCCM) horizontal continuous casting was cold rolled. Microstructure evolution and mechanical properties of the alloy as well as its deformation mechanism were investigated. The results showed that the as-cast alloy plate had columnar grains along the length direction, good surface quality and elongation of 35%, which was directly large-reduction cold rolled without surface treatment, and the accumulative cold rolling reduction reached 98%. When the reduction was small(20%), numerous dislocations and dislocation cells formed, and the deformation mechanism was dislocation slip. When the reduction was 40%, deformation twins appeared, and interactions between twins and dislocation cells induced strip-like dislocation cells. When the reduction exceeded 60%, shear bands formed and apparent crystal rotation in the micro-region happened. Further increasing the reduction, the amount of the shear bands rose and they interacted with each other, which refined the grains apparently. The tensile strength and hardness increased from 353 MPa and HV 119 of the as-cast alloy to 625 MPa and HV 208 with 95% reduction, respectively, and the elongation reduced from 35% to 7.6%. A process of HCCM horizontal continuous casting-cold rolling can work as a novel compact method to fabricate Cu-Be alloy sheet.

Numerical Simulation of Fluid Flow and Heat Transfer in Funnel Shaped Mold of Thin Slab Continuous Caster

Thin slab casting is used widely in the world. The control of molten steel flow and solidification in the mold is difficult due to the high casting speed and complicated configuration of the mold. Numerical simulation was carried out to study the fluid flow and heat transfer in the funnel shaped mold. The influence of nozzle design, casting speed and nozzle submersion depth on the flow and temperature fields in the mold was investigated, and guidance for selecting configurations of submerged nozzle was obtained.

Effect of cooling structure on thermal behavior of copper plates of slab continuous casting mold

A three-dimensional finite-element model of slab continuous casting mold was conducted to clarify the effect of cooling structure on thermal behavior of copper plates. The results show that temperature distribution of hot surface is mainly governed by cooling structure and heat-transfer conditions. For hot surface centricity, maximum surface temperature promotions are 30 ℃and 15 ℃ with thickness increments of copper plates of 5 mm and nickel layers of 1 ram, respectively. The surface temperature without nickel layers is depressed by 10 ℃ when the depth increment of water slots is 2 mm and that with nickel layers adjacent to and away from mold outlet is depressed by 7℃ and 5 ℃, respectively. The specific trend of temperature distribution of transverse sections of copper plates is nearly free of cooling structure, but temperature is changed and its law is similar to the corresponding surface temperature.

Flow and Temperature Fields in Slab Continuous Casting Molds

In order to develop super-board and super-thick slabs, the flow and temperatur fields were studied in slab continuous casting molds under different practical conditions, such as slab dimensions, with-drawing slab speed, design of nozzles, and superheat tempera-ture. The results showed that it is preferred to incline nozzle bores downwards and the submerged depth of the nozzles is best kept be-tween 250-300 mm. In addition, the solidified shell is thicker at the wide face than that at the narrow face, while the thin points alongthe wide face ekist both in the center and in the some area toward each respective end.

Heat-transfer model on the improvement of continuous casting slab temperature

A heat transfer model on the solidification process has been established onthe basis of the technical conditions of the slab caster in No.3 steel works of Wuhan Iron & SteelCorporation, and the temperature field in the solidifying slab was calculated which was verified bythe measured slab surface temperature. The influences of the main operating factors includingcasting speed, spray cooling patterns, superheat of melt and slab size on the solidification processwere analyzed and the means of enhancing the slab temperature was brought forward. Raising thecasting speed to 1.3 m/min, controlling the flowrate of secondary cooling water and improving thecooling pattern at the lower segments of secondary cooling zone could improve the slab temperatureeffectively. And the increasing the superheat is adverse to the production of high temperature slab.

Slab Storage Calculation Method for Continuous Casting-Hot Rolling

Based on load-oriented manufacturing control theory,different combining modes and slab storage calculation method for continuous casting and hot rolling were discussed.The buffer capacity index of continuous casting-rolling was introduced,and the reasonable slab storage under different combining modes was calculated with buffer capacity index of 120.00 hfor CCR,79.20 hfor HCR,19.68 hfor DHCR and 3.84 hfor DR.Thin slab is 1.20 h,and the strip is zero.Theory gist was provided for steel enterprise to decrease storage.

The startup and production of the No.4 slab continuous caster at Baosteel

In order to meet the developing requirements for the output and quality of the products of Baosteel, the No. 4 slab continuous caster designed by the Danieli Company of Italy was built. Since starting up in December, 2006, the casting machine has run smoothly in the aspects of production and quality control. It is equipped with advanced apparatus and technology, such as electric magnetic braking （EMBR） and soft reduction. Some operation indices have been continually improved, in order to ensure that slab quality meets the requirements of downstream products. Its total output reached 2.17 Mt in 2007. This study analyzes the operational indices and the slab quality.

Research on the trajectory of non-metal inclusions with the flow in the mold during the solidification of continuous casting slabs

By means of the numerical simulation method,the mathematical model of inclusions movement in the mold is established under the condition of austenitic and fen-itic stainless steel slab production. According to the simulation results, the main zones for inclusion particles accumulation were found and many factors that affected floating-up probability of inclusion particles were identified. These factors include the inclusion particle size, the casting speed and the slab width, etc. It is believed that the inclusion particle size is the key one among these factors.

Evaluation of the performance of mold powder for continuous casting of plate slabs

The No. 3 slab caster,which mainly provides slabs to the 5000 mm plate mill at Baosteel, was put into production in December,2004. The size of the biggest slab produced by this caster is 2300 mm in width and 300 mm in thickness. The designed output of the caster is 2.3 Mt/a. Slab surface longitudinal crack defects,which were related to the heat flux of the mold, frequently occurred in the early stage of the startup of the caster. As mild cooling powder is beneficial to the uniformity of the shell of initial slabs ,the concentration of stress is reduced, and the longitudinal cracking on the surface is avoided. This study evaluates the performance of several kinds of powder, and the results show that mold powder of high basicity, high crystallization proportion and low heat flux is to the benefit of the reduction of the longitudinal cracks on the surface and the defects of slabs.