Mobility and dynamic erosion process of granular flow:insights from numerical investigation using material point method

In order to understand the dynamics of granular flow on an erodible base soil,in this paper,a series of material point method-based granular column collapse tests were conducted to investigate numerically the mobility and dynamic erosion process of granular flow subjected to the complex settings,i.e.,the aspect ratio,granular mass,friction and dilatancy resistance,gravity and presence of water.A set of power scaling laws were proposed to describe the final deposit characteristics of granular flow by the relations of the normalized run-out distance and the normalized final height of granular flow against the aspect ratio,being greatly affected by the complex geological settings,e.g.,granular mass,the friction and dilatancy resistance of granular soil,and presence of water in granular flow.An index of the coefficient of friction of granular soil was defined as a ratio of the target coefficient of friction over the initial coefficient of friction to quantify the scaling extent of friction change(i.e.,friction strengthening or weakening).There is a characteristic aspect ratio of granular column corresponding to the maximum mobility of granular flow with the minimum index of the apparent coefficient of friction.The index of the repose coefficient of friction of granular flow decreased gradually with the increase in aspect ratio because higher potential energy of granular column at a larger aspect ratio causes a larger kinetic energy of granular soil to weaken the friction of granular soil as a kind of velocity-related friction weakening.An increase in granular mass reduces gradually the indexes of the apparent and repose coefficients of friction of granular soil to enhance the mobility of granular flow.The mobility of granular flow increases gradually with the decrease in friction angle or increase in dilatancy angle of granular soil.However,the increase of gravity accelerates granular flow but showing the same final deposit profile without any dependence on gravity.The mobility of granular flow increases gradually by lowering the indexes of the apparent and repose coefficients of friction of granular flow while changing the surroundings,in turn,the dry soil,submerged soil and saturated soil,implying a gradually increased excessive mobility of granular flow with the friction weakening of granular soil.Presence of water in granular flow may be a potential catalyzer to yield a long run-out granular flow,as revealed in comparison of water-absent and water-present granular flows.In addition,the dynamic erosion and entrainment of based soil induced by granular flow subjected to the complex geological settings,i.e.,the aspect ratio,granular mass,gravity,friction and dilatancy resistance,and presence of water,were comprehensively investigated as well.

3D modeling for effect of tool eccentricity on coupled thermal and material flow characteristics during friction stir welding

A novel three-dimensional numerical model is proposed to investigate the effect of tool eccentricity on the coupled thermal and material flow characteristics in friction stir welding(FSW) process.An asymmetrical boundary condition at the tool-workpiece interface,and the dynamic mesh technique are both employed for the consideration of the tool eccentricity during tool rotating.It is found that tool eccentricity induces the periodical variation of the heat densities both at the tool-workpiece interface and inside the shear layer,but the fluctuation amplitudes of the heat density variations are limited.However,it is demonstrated that tool eccentricity results in significant variation of the material flow behavior in one tool rotating period.Moreover,the material velocity variation at the retreating side is particularly important for the formation of the periodic characteristics in FSW.The modeling result is found to be in good agreement with the experimental one.

Visualization and simulation of plastic material flow in friction stir welding of 2024 aluminium alloy plates

Thin copper sheets as marker material were embedded into weld path of 2024 aluminium alloy plates and their final position after friction stir welding was examined by metallographic techniques. Referring to the visualized material flow patterns, a three-dimensional model was developed to conduct the numerical simulation of the temperature profile and plastic material flow in friction stir welding. The calculated velocity contour of plastic flow in close proximity of the tool is generally consistent with the visualized results. As the tool rotation speed increases at a constant tool travel speed, the material flow near the pin gets stronger. The predicted shape and size of the weld nugget zone match with the experimentally measured ones.

A Study on Alien Invasive Plants from the Interactive Mechanism between Species Niche and Material/Energy Flow

[Objective]This study was to reveal the essence of mechanism about how the alien invasive plants spread.[Method]Species niche and material/energy flow were used as basic research indicators to analyze the intrinsic mechanism of alien plants invasion.[Result]Most of the invasive plants have not been explicitly defined and their effective control methods not brought forward.[Conclusion]Overrun of alien invasive plants depends on whether the niche of a species could be continuously met at spatial level.Based on this we put forward corresponding control measures,proposed an assumption to establish a cylinder-network model and discussed the definition of alien invasive plants.

Impact of material and energy flow variation-based iron /steel ratio on production cost

This paper establishes a model for the production cost of iron and steel enterprise.The variation rule of the production cost versus the iron/steel ratio for two cases, namely,fixed steel production and a fixed amount of molten iron,is analyzed,and the concept of a steel scrap threshold price is proposed.According to the analysis results,when the steel scrap unit price exceeds the steel scrap threshold price, an increase in the iron/steel ratio can reduce the production cost,and vice versa.When the gap between the steel scrap unit price and the steel scrap threshold price is relatively large, the impact of the iron/steel ratio on the production cost is more prominent.According to the calculation example,when steel production is fixed （284 358 t/month）and the steel scrap unit price is 263.2 yuan/t more than the steel scrap threshold price,an increase of 0.01 in the iron/steel ratio causes a monthly production cost reduction of approximately 750 000 yuan （2.63 yuan/t）.When the amount of molten iron is fixed （270 425 t/month）and the steel scrap unit price is 140.7 yuan/t more than the threshold price,an increase of 0.01 in the iron/steel ratio causes a monthly production cost reduction of approximately 430 000 yuan （1.5 yuan/t）.The results indicate that iron and steel enterprise should adjust the production strategy in time when the scrap price fluctuates, and then the production cost will be reduced.

Calculating Method for Influence of Material Flow on Energy Consumption in Steel Manufacturing Process

From the viewpoint of systems energy conservation, the influences of material flow on its energy consumption in a steel manufacturing process is an important subject. The quantitative analysis of the relationship between material flow and the energy intensity is useful to save energy in steel industry. Based on the concept of standard material flow diagram, all possible situations of ferric material flow in steel manufacturing process are analyzed. The expressions of the influence of material flow deviated from standard material flow diagram on energy consumption are put forward.

Materials flow and phase transformation in friction stir welding of Al 6013/Mg

Material flow and phase transformation were studied at the interface of dissimilar joint between Al 6013 and Mg, produced by stir friction welding （FSW） experiments. Defect-free weld was obtained when aluminum and magnesium were placed in the advancing side and retreating side respectively and the tool was placed 1 mm off the weld centerline into the aluminum side. In order to understand the material flow during FSW, steel shots were implanted as indexes into the welding path. After welding, using X-ray images, secondary positions of the steel shots were evaluated. It was revealed that steel shots implanted in advancing side were penetrated from the advancing side into the retreating side, whereas the shots implanted in the retreating side remained in the retreating side, without penetrating into the advancing side. The welded specimens were also heat treated. The effects of heat treatment on the mechanical properties of the welds and the formation of new intermetallic layers were investigated. Two intermetallic compounds, Al3Mg2 and Al12Mg17, were formed sequentially at Al6013/Mg interface.

Influence of Material Flow in Steel Manufacturing Process on Atmosphere Environmental Load

The standard material flow diagram in steel manufacturing process was proposed to analyze the influences of various material flows on environmental load of 1tof final product.Two influence factors and reducing measures of environmental load were pointed out.The environmental load was appraised for a typical technological process in a Chinese steel plant.

Simulation of 3D material flow in friction stir welding of AA6061-T6

This paper reports the numerical simulation of the 3D material flow in friction stir welding process by using finite element methods based on solid mechanics. It is found that the material flow behind the pin is much faster than that in front of the pin. The material in front of the pin moves upwards and then rotates with the pin due to the effect of the rotating tool. Behind of the pin, the material moves downwards. This process of material movement is the real cause to make the friction stir welding process continuing successfully. With the increase of the translational velocity or the rotational velocity of the pin, the material flow becomes faster.

Effects of pin geometry on the material flow behavior of friction stir spot welded 2A12 aluminum alloy

A three-dimensional finite volume model was established by the ANSYS FLUENT software to simulate the material flow behavior during the friction stir spot welding （FSSW） process. Effects of the full-threaded pin and the reverse-threaded pin on the material flow behavior were mainly discussed. Results showed that the biggest material flow velocity appeared at the outer edge of the tool shoulder. The velocity value became smaller with the increase of the distance away from the tool surface. In general, material flows downwards along the pin thread when the full-threaded pin is used. Meanwhile, both the materials of the upper and the lower plates flow towards the lap interface along the pin thread when the reverse-threaded pin is used. The numerical simulation results were investigated by experiment, in which 2A12 aluminum alloy was used as the research object. The effective sheet thickness （EST） and stir zone （SZ） width of the joint by the reverse-threaded pin were much bigger than those by the full-threaded pin. Accordingly, cross tension failure load of the joint by the reverse-threaded pin is 23% bigger than the joint by the full-threaded pin.

3D visualization of the material flow in friction stir welding process

The material flow in friction stir welded 2014 Al alloy has been investigated using a marker insert technique （MIT）. Results of the flow visualization show that the material flow is asymmetrical during the friction stir welding （FSW） process and there are also significant differences in the flow patterns observed on advancing side and retreating side. On advancing side, some material transport forward and some move backward, but on retreating side, material only transport backward. At the top surface of the weld, significant material transport forward due to the action of the rotating tool shoulder. Combining the data from all the markers, a three-dituensional flow visualization, similar to the 3D image reconstruction technique, was obtained. The three-dimensional plot gives the tendency chart of material flow in friction stir welding process and from the plot it can be seen that there is a vertical, circular motion around the longitudinal axis of the weld. On the advancing side of the weld, the material is pushed downward but on the retreating side, the material is pushed toward the crown of the weld. The net result of the two relative motions in both side of the advancing and the retreating is that a circular motion comes into being. Comparatively, the material flow around the longitudinal axis is a secondary motion.

Numerical simulations on material flow behaviors in whole process of friction stir welding

A finite element model based on solid mechanics was developed with ABAQUS to study the material flow in wholeprocess of friction stir welding （FSW）, with the technique of tracer particles. Simulation results indicate that the flow pattern of thetracer particles around the pin is spiral movement. There are very different flow patterns at the upper and lower parts of the weld. Thematerial on the upper surface has the spiral downward movement that is affected by the shoulder and the lower material has the spiralupward movement that is affected by the pin. The velocity of the material flow on the periphery of the stirring pin is higher than thatat the bottom of the stirring pin. The material can be rotated with a stirring pin a few times, agreeing well with the previousexperimental observation by tungsten tracer particles.

Influence of welding parameters on material flow,mechanical property and intermetallic characterization of friction stir welded AA6063 to HCP copper dissimilar butt joint without offset

Joining of dissimilar aluminium-copper is an emerging area of interest for both research and industry due to its complex nature.Friction stir welding was attempted to evaluate the joint strength without offset at the butt line between AA6063 to HCP copper sheet under different combination of rotational speed of 800 and 1000 r/min and travel speed of 20 and 40 mm/min.Material flow was studied in detail for different combinations of parameters with optical microscopy and elemental mapping by energy dispersive X-ray spectroscopy（EDS）.The results were correlated with the microstructural characteristics and formation of intermetallics at the bond interface using microhardness test and X-ray diffraction（XRD） technique.Material flow clearly suggests that energy input at 800 r/min and 20 mm/min is sufficient to plasticize both the materials with formation of higher amount of thermodynamically stable and hard intermetallic phases Al4Cu9 and Al Cu4（slower cooling rate of 88 K/s） than that at 800 r/min and 40 mm/min（faster cooling rate of 154 K/s）,attributed maximum joint strength（~78.6% of aluminium base metal）.

Laboratory-scale investigation of the material distribution characteristics of landslide dams in U-shaped valleys

Material distribution characteristics during sliding and depositing is particularly significative to investigate the internal structure and spatial variation of landslide dams,which are fundamentally determining the mechanical and hydraulic behavior and the susceptibility to cause dam failure.However,limited by longevity shortages and special geographic environments,the material distribution characteristics and their formation mechanisms are difficult to observe in the field.Therefore,an experimental apparatus modeling a landslide dam was developed in this paper,designing three sampling methods with two valley states.The internal deposit characteristics,void ratio variation and relative content of the particle size range(PSR)were analyzed,and the mechanics of deposit structure were also delicately ascertained.The results indicate that granular material deposited in valley shows a structure of inverse grain size accumulation in both vertical and horizontal directions,exhibiting spatial variability of particle gradation and void ratio.The characteristic PSR decreases from 22-30 mm in the two-dimensional state to 10-14 mm in the threedimensional state.Vibration excitation and vibration sieve are the intrinsic mechanisms of granular flow segregation,intrinsically inducing the formation of inverse grading deposit structures.Consequently,spatial variability in size is mainly trig gered by segregation,whereas coarse particle content and deposition boundaries merely exacerbate the difference degree.

Material flow control technology of ironmaking and steelmaking interface

In order to achieve higher efficient cohesion match of procedure and equipment between ironmaking and steelmaking interface, the theory of multi-dimensional material flow control was applied to analyze torpedo ladle-iron ladle transportation process between blast furnace and basic oxygen furnace. Moreover, basic parameters of material flow were analyzed and optimized, such as time, temperature and material quantity. Based on operating principles of material flow, control methods were optimized, such as product organization mode, scheduling discipline and scheduling plan of hot metal ladle. Finally, the material flow control technology of ironmaking and steelmaking interface was integrated. Satisfactory effects are obtained after applying the technology in practice. The total turnover number of torpedo ladle decreases from 20 to 18, the hot metal temperature of 1# BF torpedo ladle decreases from 36 °C to 19.5 °C, the hot metal temperature of 2# BF torpedo ladle decreases from 36.6 °C to 19.8 °C, the temperature drop of desulfurization hot metal decreases by 4 °C, and the temperature drop of non-desulfurization hot metal decreases by 2.8 °C. Furthermore, the ironmaking and steelmaking interface system will realize high-efficiency control by using this control technology.

Effect of welding speed on the material flow patterns in friction stir welding of AZ31 magnesium alloy

The clear zigzag-line pattern on transverse cross sections can be used to explain the formation mechanism of the weld nugget when friction stir welded AZ31 magnesium alloy without any other insert material is used as mark. It provides a simple and useful method to research the joining mechanism of friction stir welding. The rotation speed is kept at 1000 r/min and the welding speed changes from 120 mm/min to 600 mm/min. The macrostructure on the transverse cross section was divided into several parts by faying surface. The results show that the shape and formation procedure of the weld nugget change with the welding speed. There are two main material flows in the weld nugget： one is from the advancing side and the other is from the retreating side. A simple model on the weld nugget formation of FSW is presented in this article.

Effect of knurling shoulder design with polygonal pins on material flow and mechanical properties during friction stir welding of Al-Mg-Si alloy

Understanding the material flow facilitated by tool geometry in friction stir welds is challenging for quality weld production in industrial applications.The optimal tool shoulder and pin design combination,which plays a vital role in material flow was addressed.The flow of plasticized material was analyzed using a marker insert technique.The results show that the knurling shoulder design with square and hexagonal pin design facilitated constant stability force with reference to weld length/time.The uniform mixing and distribution of plasticized material were facilitated by the knurling shoulder design with square tool pin shape(TK)S(sticking length minimum)below which fragmented copper was observed.(TK)S tool facilitated higher mechanical properties for the welds,i.e.strength(182 MPa)and hardness(HV 78)in stir zone.

Rheological Behaviour for Polymer Melts and Concentrated SolutionsPart Ⅱ: Material Function with Nagai Chain Constraints and Determination of Their Parameters from Flow Curves

An integral constitutive equation and a set of material functions for describing the strain history of polymer melts were formulated in terms of the Cauchy-Green and Finger tensors. A simple memory function and the dependence of ηo and τt on M3.4 were derived from the theory of non-linear viscoelasticity with constraints of entanglements for polymer melts and substituted into the Oldroye-Walters-Fredickson constitutive equation. An integral constitutive equation for polymer melts was consequently obtained. Some material functions of the constitutive equation related to certain 'test flow' are examined as follows : (1) simple steady shear flow; (2) steady elongation flow; (3) small-amplitude oscillatory shear flow; (4) stress growth upon the inception of steady shear elongation flow; (5) stress relaxation (modulus and compllance). These theoretical relations for simple steady shear flow were compared with experimental data from our laboratory and references for various polymer melts and concentrated solutions. A good agreement between the theory and experiment was achieved.

Analysis of material flow and heat transfer in friction stir welding of aluminium alloys

A three-dimensional viscous-plastic.finite element model is established based on computational fluid mechanics. The material during the welding process is considered as non-Newtonian fluid abided by Norton-Hoff constitutive law, and viscous dissipation is assumed as the unique heat source. The model is used to numerically simulate the material flow and heat transfer in friction stir welding, and capture some useful process characteristics, .such as heat generation, temperature distribution and fluid.flow; besides, the velocity field is used to calculate streamlines of material flow, and the dimension of the deformation zone is measured.

Super energy flows in a waveguide filled with air and left-handed materials

The phenomena of super energy flows are studied theoretically and numerically in a parallel-plate waveguide which is filled with two layered equally-thick different media, i.e. air and specific left-handed materials （LHM） with εr1 = -1/（1 ＋δ） ＋iγ and μr1 = -（1 ＋ δ） ＋ iγ. In this special waveguide, two-directional super-energy flows are excited by a three-dimensional horizontal electric dipole at the same time, which has transmission patterns different from those of two-dimensional source and three-dimensional vertical electric dipole. We also show that the retardation and loss in LHM are sensitive to the amplitude of super power densities, and the dimensions of waveguide determine the propagating modes, which makes super energy flows more practical.