Powder injection molding of pure titanium

An improved wax-based binder was developed for powder injection molding of pure titanium. A critical powder loading of 69 vol.% and a pseudo-plastic flow behavior were obtained by the feedstock based on the binder. The injection molding, debinding, and sintering process were studied. An ideal control of carbon and oxygen contents was achieved by thermal debinding in vacuum atmosphere （10^-3 Pa）. The mechanical properties of as-sintered specimens were less than those of titanium made by the conventional press-sintering process. Good shape retention and ±0.04 mm dimension deviation were achieved.

NUMERICAL SIMULATION OF FEEDSTOCK MELT FILLING IN A CYLINDRICAL CAVITY WITH SOLIDIFICATION IN POWDER INJECTION MOLDING

ＩＮＴＲＯＤＵＣＴＩＯＮＰｏｗｄｅｒｉｎｊｅｃｔｉｏｎｍｏｌｄｉｎｇ（ＰＩＭ）ｉｓａｐｒｏｃｅｓｉｎｇｒｏｕｔｅｆｏｒｆａｂｒｉｃａｔｉｎｇｍｅｔａｌｏｒｃｅｒａｍｉｃｃｏｍｐｏｎｅｎｔｓｗｉｔｈｃｏｍｐｌｅｘｓｈａｐｅａｎｄｈｉｇｈｐｅｒｆｏｒ?..

Powder injection molding of Fe-Ni soft magnetic alloys

With miniaturization and complication of the shape of electronic devices in recent years, powder injection molding (PIM) seems to be a suitable process for fabricating the higher performance soft magnetic components. In this paper, high quality Fe-50Ni soft magnetic alloy was fabricated by PIM with carbonyl iron and nickel, and the effect of sintering process on its microstructure and magnetic properties were investigated. The mechanical and magnetic properties can be obviously improved by increasing the sintering temperature or using the hydrogen atmosphere instead of high vacuum, which causes by the increase of grain size and the densification. At the optimum sintering conditions, the PIM Fe-50Ni soft magnetic alloy with high properties are obtained, whose relative density, tensile strength, Bm, Hc, μm are 97%, 465 MPa, 1.52 T, 16.62 A·m-1, 42.5 mH·m-1, respectively.

Rheological properties of feedstocks for powder extrusion molding

The rheological behaviors of feedstocks for powder extrusion molding, in the temperature range of 40～80 ℃ and the Newton shear rate of 3～800 s -1 , were studied. The effects of feedstock constitution, shear rate and temperature on apparent viscosity, shear stress and active energy were investigated. The viscose flow active energy of PEM feedstocks is 15.89～90.77 kJ/mol. Based on this research, the PEM technical parameters have optimized. [

Injection molding of nano structured 90W-7Ni-3Fe alloy powder prepared by high energy ball milling

Blended elemental 90W 7Ni 3Fe (mass fraction, %) powder was mechanically alloyed in a planetary ball mill. Nano crystalline grains were obtained after 10 h milling. The nano structured powder was processed to full density by metal injection molding approach. Compacts from the optimal powder binder mixture were studied for molding and sintering behaviors. Milling significantly increases the maximum powder loading and homogeneity of the feedstock, and enhances the sintering densification process. When solid state sintered at 1 350～1 450 ℃, the alloy shows very fine grains (～3 μm), high tensile strength (>1 130 MPa) and almost no distortion. [

Powder Extrusion Molding of Nanocrystalline WC-10Co Composite Cemented Carbide

The rods that were shaped from nanocrystalline WC- 10.21 Co-0.42 VC/ Cr3 C2 （ wt% ） composite powders by using powder extrusion molding （PEM） were investigated. The nanocrystalline WC- 10.21 Co- 0. 42 VC/ Cr3 C2 （ wt% ） composite powders were prepared by the spray thermal decomposition-continuous reduction and carburization technology. In order to improve the properties of rods shaped by using powder extrusion molding, the cold isostatic pressing （CIP） technology was used before or after debinding. Specimens were siutered by vacuum siutering and hot isostatic pressing （HIP）. The density, Rockwell A hardness, magnetic coercivity , and magnetic saturation induction of siutered specimen were measured. The microstructure of the green bodies and the siutered specimens was studied by scanning electron microscopy （SEM）. Results show that the rod formed by using powder extrusion molding after debinding and followed by cold isostatic pressing can be siutered to 99.5% density of composite cemented carbide rods with an average grain size of about 200- 300 nm, magnetic coercivity of 30.4 KA / m, Rockwell A hardness of 92.6 and magnetic saturation induction of 85% . Superfine WC- 10 Co cemented carbide rods with excellent properties were obtained.

Preparation of high nitrogen and nickel-free austenitic stainless steel by powder injection molding

High nitrogen and nickel-free austenitic stainless steel has received much recognition worldwide because it can solve the problem of ＂nickel-allergy＂ and has outstanding mechanical and physical properties. In this article, 0Cr17Mn11Mo3N was prepared by powder injection molding （PIM） technique accompanied with solid-nitriding. The results show that the critical solid loading can achieve up to 64vol% by use of gas-atomized powders with the average size of 17.4 μm. The optimized sintefing conditions are determined to be 1300℃,2 h in flowing nitrogen atmosphere, at which the relative density reaches to 99% and the N content is as high as 0.78wt%. After solution annealing at 1150℃for 90 rain and water quench, the 0.2% yield strength, ultimate tensile strength （UTS）, elongation, reduction in area, and hardness can reach as high as 580 MPa, 885 MPa, 26.0%, 29.1%, and Hv 222, respectively.

Phase Behaviors in Bi-phase Simulation of Powder Segregation in Metal Injection Molding

Powder segregation induced by mold filling is an important phenomenon that affects the final quality of metal injection molding （MIM）. The prediction of segregation in MIM requires a bi-phase flow model to describe distinctly the flows of metallic powder and polymer binder. Viscous behaviors for the flows of each phase should hence be determined. The coefficient of interaction between the flows of two phases should also be evaluated. However, only viscosity of the mixed feedstock is measurable by capillary tests. Wall sticking is supposed in the traditional model for capillary tests, while the wall slip is important to be taken into account in MIM injection. Objective of the present paper is to introduce the slip effect in bi-phase simulation, and search the suitable way to determine the viscous behaviors for each phase with the consideration of wall slip in capillary tests. Analytical and numerical methods were proposed to realize such a specific purpose. The proposed method is based on the mass conservation between the capillary flows in mono-phase model for the mixed feedstock and in bi-phase model for the flows of two phases. Examples of the bi-phase simulation in MIM were realized with the software developed by research team. The results show evident segregation, which is valuable for improving the mould designs.

A novel binder and binder extraction method for powder injection molding of tungsten cemented carbide

An improved wax based multi component binder and a new debinding method termed high pressure condensed solvent extraction were developed for powder injection molding of tungsten cemented carbide. The results indicate that a critical powder loading of 65% (volume fraction) and an ideal rheological properties were obtained by the feedstock based on the binder. High debinding rate and specimens with high strength were obtained by the debinding method. Moreover, by making high temperature holding time adjustable, it makes the subsequent thermal degradation process more flexible to debinding atmosphere and carbon content of the as debinded specimens controllable. The transverse rupture strength, hardness and density of the as sintered specimens made by an optimized PIM process are 2.48 GPa, HRA90 and 14.72 g/cm 3, respectively. Good shape retention and about 0.02% dimension deviation were achieved.

Fabrication and properties of binder for powder extrusion molding

By optimizing formulation and fabrication methods, a new binder forplasticizing powder extrusion molding of hard metal, with excellent integrated properties anduniform distribution characters, has been developed. Thermal debonding mechanism and the extrudingtheological behaviours have been studied. The technology of fabrication of binder and thermaldebonding process have also been investigated. Using the novel binder, the hard-metalextrusion-molding rods with diameter up to 25mm, have been manufactured.

Comparison of rheological analytic model with numerical simulation in powder injection molding filling process

Mathematical model of filling disk-shaped mold cavity in steady state was studied.And the mathematical model under vibration field was developed from the model in steady state.According to the model of filling disk-shaped mold cavity in steady state,the filling time,the distribution of velocity field and the pressure field were obtained.The analysis results from rheological analytic model were compared with the numerical simulation results using Moldflow software in the powder injection molding filling process.Through the comparison,it is found that it is unreasonable to neglect the influence of temperature when calculated the pressure changing with the time at the cavity gate,while it can be neglected in other situations such as calculating the distribution of the velocity fields.This provides a theoretical reference for the establishment of correct model both in steady state and under vibration force field in the future.

Microstructure and properties of nano-TiN modified Ti(C,N)-based cermets fabricated by powder injection molding and die pressing

Powder injection molding （PIM） and die pressing were employed to fabricate nano-TiN modified Ti（C,N）- based cermets. The shrinkage behavior, microstructure, porosity, and mechanical properties of the samples with and without nano-TiN addition fabricated by PIM and die pressing were analyzed. It is demonstrated that for either PIM or die pressing, the porosities are obviously reduced, the mechanical properties are significantly improved after adding nano-TiN, and the hard particles are refined; the rim phase thickness obviously becomes thinner, and the number of dimples in fracture also increases. Compared the samples fabricated by die pressing, it is difficult for PIM to obtain dense Ti（C,N）-based cermets. Due to the too much existence of pores and isolated carbon, the mechanical properties of the sintered samples by PIM are inferior to those of the sintered ones by die pressing.

Numerical Simulation of Powder Injection Molding Filling Process Based on ANSYS

A mathematical model of two-dimensional flows of PIM derived from the momentum, continuity equations and theheat transfer equation is obtained. The formula of calculating the flow conductance and the pressure equation arededuced when the no slip boundary condition is employed at the wall, and the pressure equation is a non-linearelliptic partial differential equation. The flow front locations, distribution of velocities, temperature and pressure aresimulated by the finite element analysis software ANSYS. Simulation results indicate that it is in the final filled partthat defects appear easily. The region in which the defects may occur during the PIM process can be predicted.

Sintering Mechanism of Stainless Steel in Powder Injection Molding

Stainless steel samples were made by Powder injection Molding (PIM) process with-400 mesh powder in order to investigate the sintering mechanism in this system and develop the PIM of stainless steels. The process included mixing, injection molding, debin- ding and sintering. Neck growth model was used to analyze the sintering mechanism. The results show that lattice (volume) diffusion is the main mechanism in the sintering process, the products with higher density (>95%) and properties are obtained. At lower temperatures, grain boundary diffusion may play a role in the sintering densification.

Chemistry principles for thermoplastic polymer binder formula selection for powder injection molding

The polymer binder selection is one of the very important aspects for the powder injection molding. However,even nowadays the binder selection is still mainly performed by try and error method. Six commercial or intensive studied binder fo rmulas were analyzed according to state diagram and chemical characteristics of ingredients in each binder formula. In addition,the interactions between the bi nder components and additives were also taken into account. Based on the analysi s,the optimum binder formula was selected and some selection criterions were pu t forward for the binder and additives.

Fractal phenomena in powder injection molding process

The complicated characteristics of the powder were studied by fractal theory. It is illustrated that powder shape, binder structure, feedstock and mold filling flow in powder injection molding process possess obvious fractal characteristics. Based on the result of SEM, the fractal dimensions of the projected boundary of carbonylic iron and carbonylic nickel particles were determined to be 1.074±0.006 and 1.230±0.005 respectively by box counting measurement. The results show that the fractal dimension of the projected boundary of carbonylic iron particles is close to smooth curve of one dimension, while the fractal dimension of the projected boundary of carbonylic nickel particle is close to that of trisection Koch curve, indicating that the shape characteristics of carbonylic nickel particles can be described and analyzed by the characteristics of trisection Koch curve. It is also proposed that the fractal theory can be applied in the research of powder injection molding in four aspects.

Numerical simulation of tungsten alloy in powder injection molding process

The flow behavior of feedstock for the tungsten alloy powder in the mold cavity was approximately described using Hele-Shaw flow model. The math model consisting of momentum equation, consecutive equation and thermo-conduction equation for describing the injection process was established. The equations are solved by the finite element/finite difference hybrid method that means dispersing the feedstock model with finite element method, resolving the model along the depth with finite difference method, and tracking the movable boundary with control volume method, then the pressure equation and energy equation can be resolved in turn. The numerical simulation of the injection process and the identification of the process parameters were realized by the Moldflow software. The results indicate that there is low temperature gradient in the cavity while the pressure and shear rate gradient are high at high flow rate. The selection of the flow rate is affected by the structure of the gate. The shear rate and the pressure near the gate can be decreased by properly widening the dimension of the gate. There is a good agreement between the process parameters obtained by the numerical simulation and the actual ones.

Water modeling of mold powder entrapment in slab continuous casting mold

The optimal parameters were determined by the water modeling of slab casting. It was found that there are mainly three types of mold powder entrapment in slab continuous casting, i.e., the entrapment caused by the shearing flow near the narrow face of mold, the entrapment caused by vortexes around the submerged entry nozzle （SEN）, and the entrapment caused by the Ar bubbling. Both the velocity of the surface flow and the level fluctuation of the liquids are enlarged with increasing the casting speed, reducing the submersion depth of SEN, decreasing the downward angles of the nozzle outlets, and increasing the Ar flowrate, all of which increase the tendency of mold powder entrapment. Among the four above-mentioned factors, casting speed has the largest effect.

Injection molding of micro-porous titanium alloy with space holder technique

The powder space holder （PSH） and powder injection molding （PIM） methods have an industrial competitive advantage because they are capable of the net-shape production of micro-sized porous parts. In this study, micro-porous Ti6Al4V alloy （Ti64） parts were produced by the PSH-PIM process. Ti64 alloy powder and spherical polymethylrnethacrylate （PMMA） particles were used as a space holder material. After molding, binder debinding was performed by thermal method under inert gas. Debinded samples were sintered at 1250℃ for 60min in a vacuum （10-4 Pa）. Metallographic studies were conducted to determine densification and the corresponding microstructural changes. The surface of sintered samples was examined by SEM. The compressive stress and elastic modulus of the rificro-porous Ti64 samples were determined. The effects of fraction of PMMA on the properties of sintered micro-porous Ti64 alloy samples were investigated. It was shown that the fraction of PMMA could be controlled to affect the properties of the Ti alloy.

Effects of heat treatment on the properties of powder injection molded AlN ceramics

The effects of two different heat-treatment atmospheres,nitrogen atmosphere and reducing nitrogen atmosphere with carbon,on the properties of Y2O3-doped aluminum nitride（AlN） ceramics were investigated.The AlN powder as a raw material was synthesized by self-propagating high-temperature synthesis（SHS） and compacts were fabricated by employing powder injection molding technique.The polymer-wax binder consisted of 60 wt.% paraffin wax（PW）,35 wt.% polypropylene（PP）,and 5 wt.% stearic acid（SA）.After the removal of binder,specimens were sintered at 1850°С in nitrogen atmosphere under atmospheric pressure.To improve the thermal conductivity,sintered samples were reheated.The result reveals that the heat-treatment atmosphere has significant effect on the properties and secondary phase of AlN ceramics.The thermal conductivity and density of AlN ceramics reheated in nitrogen gas are 180 W·m^-1·K^-1 and 3.28 g·cm^-3 and the secondary phase is yttrium aluminate.For the sample reheated in reducing nitrogen atmosphere with carbon,the thermal conductivity and density are 173 W·m^-1·K^-1 and 3.23 g·cm^-3,respectively,and the secondary phase is YN.