Preparation of Thermal Insulation Ceramics Using Felsic Tailings as Main Raw Material and Soda-ash Dregs as Flux

Low-cost thermal insulation porous ceramics with uniform pore diameter and low bulk density were prepared with soda-ash dregs and felsic tailings.We investigated the effect of temperature,foaming agent,fluxing agent,Al_(2)O_(3)and CaO content on the pore structure and crystal phase of porous ceramics.The effect of Ca^(2+)in soda-ash dregs on the preparation of quartz-feldspar based porous ceramics was studied.The results showed that the contribution of Ca^(2+)to the preparation of porous ceramics in this system was mainly to accelerate the Si-O bond fracture and reduce the sintering temperature at the initial stage of sintering,which destroyed the needle-like feldspar in the high temperature melt and reduced the melt viscosity,thus reduced the foaming resistance and promoted the porous products with uniform pore size distribution.The Ca^(2+)content on the high side can participate in the formation of crystals in sintering.The generated needle-like diopside and augite,which have small length-diameter ratio,will negligibly change in the viscosity of melt at high temperatures,and their inhibition effect on pores is not as good as that of feldspar with large length-diameter ratio,resulting in the merger and collapse of pores.But the increase of diopside and augite can improve the compressive strength of porous products to some extent.Porous ceramic products containing needle-like feldspar phase can be prepared by using two kinds of solid waste,which can improve the compressive strength of the products and reduce the raw material cost and energy consumption while comprehensively utilizing the double solid waste.The optimal product has a bulk density of 0.45 g/cm^(3),a compressive strength of 3.17 MPa,and a thermal conductivity of 0.11 W/(m·K).

Thermal Insulation Materials of Alumina Based Porous Ceramics

Significant energy saving effects can be made through the improvement of furnace refractories,especially the thermal insulation refractories. In this study,the preparation and the application of different alumina based porous ceramics were briefly introduced. Alumina based porous ceramics were prepared combined foaming method with gelcasting,sol- gel process or cement curing process. The influences of different preparation methods on the sintering shrinkage, porosity, phase composition, microstructure, compressive strength and thermal conductivity were discussed. Alumina based porous ceramics with relatively high strength and low thermal conductivity could be obtained through the above mentioned methods. Compared with the traditional lining materials,about 40% energy could be saved when they were used as the furnace wall.

Crack patterns corresponding to the residual strength plateau of ceramics subjected to thermal shock

The formation strength plateau of ceramics is addressed. A set of of 99A1203 are conducted, mechanism of the residual subjected to thermal shock thermal shock experiments where the thin specimens of 1 mm× 10 mm×50 mm exhibit parallel through edge cracks, and thus permit quantitative measurements of the crack patterns. The cracks evolve with the severity of ther- mal shock. It is found that there is a correlation between the length and density of the thermal shock cracks. The increase of crack length weakens the residual strength, whereas the increase of crack density improves it. In a considerably wide temperature range, the two contrary effects just counteract each other; consequently a plateau appears in the variation curve of the residual strength. A comparison between the numerical and experimental results of the residual strength is made, and they are found in good agreement. This work is helpful to a deep understanding of the thermal shock failure of ceramics.

Preparation and Characterization of Andalusite Ceramic Used for Solar Thermal Power Generation

High-temperature thermal storage material is one of the critical materials of solar thermal power generation system. Andalusite, kaolin, talc, γ-Al2O3 and partially stabilized zireonia were used as the raw materials, and in-situ synthesis of cordierite was adopted to fabricate thermal storage material for solar thermal power generation via pressureless sintering. The phase compositions, microstructures and thermal shock resistances of the sintered samples were analyzed by XRD, SEM and EDS, and the corresponding mechanical properties were measured. The results show that the major phases of the samples are mullite and zirconium silicate, and the pores distribute uniformly. After being sintered at 1 460℃C, A4 sample exhibits a better mechanical performance and thermal shock resistance, its loss rate of bending strength after 30 cycles thermal shock is 3.04%, the bulk density and bending strength are 2.86 g.cm^-3 and 139.66 MPa, respectively. The better thermal shock resistance of the sample is closely related to the effect of zirconium silicate, such as its uniform distribution, nested growth with mullite, low thermal expansion coefficient, high thermal conductivity, etc. This ceramic can be widely used as one of potential thermal storage materials of solar thermal power generation system.

Fabrication and Thermal Structural Characteristics of Ultra-high Temperature Ceramic Struts in Scramjets

ZrB_2-SiC based ultra-high temperature ceramic（UHTC） struts were firstly proposed and fabricated with the potential application in the combustor of scramjets for fuel injection and flame-holding for their machinability and excellent oxidation/ablation resistance in the extreme harsh environment. The struts were machined with electrospark wire-electrode cutting techniques to form UHTC into the desired shape, and with laser drilling to drill tiny holes providing the channels for fuel injection. The integrated thermal-structural characteristic of the struts was evaluated in high-temperature combustion environment by the propane-oxygen free jet facility, subject to the heat flux of 1.5 MW/m^2 lasting for 300 seconds, and the struts maintained integrity during and after the first experiment. The experiments were repeated for verifying the reusability of the struts. Fracture occurred during the second repeated experiment with the crack propagating through the hole. Finite element analysis（FEA） was carried out to study the thermal stress distribution in the UHTC strut. The simulation results show a high thermal stress concentration occurs at the hole which is the crack initiation position. The phenomenon is in good agreement with the experimental results. The study shows that the thermal stress concentration is a practical key issue in the applications of the reusable UHTC strut for fuel injection structure in scramjets.

Effect of microstructure on the mechanical, thermal, and electronic property measurement of ceramic coatings

Ceramic materials were investigated as thermal barrier coatings and electrolytes. Electrophoretic deposition（EPD） and physical vapor deposition（PVD） were employed to fabricate samples, and the mechanical properties and microstructure were examined by nanoindentation and microscopy, respectively. Yttria-stabilized zirconia/alumina（YSZ/Al2O3） composite coatings, a candidate for thermal barrier coatings, yield a kinky, rather than smooth, load–displacement curve. Scanning electron microscope（SEM） examination reveals that the kinky curve is because of the porous microstructure and cracks are caused by the compression of the indenter. Li0.34La0.51 Ti O2.94（LLTO） on Si/Sr Ru O3（Si/SRO） substrates, an ionic conductor in nature, demonstrates electronic performance. Although SEM images show a continuous and smooth microstructure, a close examination of the microstructure by transmission electron microscopy（TEM） reveals that the observed spikes indicate electronic performance. Therefore, we can conclude that ceramic coatings could serve multiple purposes but their properties are microstructure-dependent.

Influence of dopant concentration on the transparent and thermal properties of Nd_2O_3-doped alumina translucent ceramics

The transparent and thermal developments of high-purity Al_2O_3 doped with different levels of Nd_2O_3 were investigated. Dopant levels ranged from 500–1500 ppm（Nd/Al atomic ratio）. The samples were characterized with X-ray diffraction（XRD）, scanning electron microscopy（SEM）, Raman spectroscopy, transmittance spectroscopy and specific heat measurement. Results revealed that with proper Nd doped, Nd^（3＋） ions solid dissolved in Al_2O_3 lattice, resulting in small and uniform grain and high bonding vibration, which was beneficial to transparent and thermal properties. With 1000 ppm Nd doped, Al_2O_3 translucent ceramics showed a total transmittance of 89% and thermal conductivity of 41.7 W/m/K, indicating a potential application as substrate for effective heat dissipation and multi emitting surface in LEDs module.