Efficient activation of the Co/SBA-15catalyst by high-frequency AC-DBD plasma thermal effects for toluene removal

Dielectric barrier discharge(DBD)plasma excited by a high-frequency alternating-current(AC)power supply is widely employed for the degradation of volatile organic compounds(VOCs).However,the thermal effect generated during the discharge process leads to energy waste and low energy utilization efficiency.In this work,an innovative DBD thermally-conducted catalysis(DBD-TCC)system,integrating high-frequency AC-DBD plasma and its generated thermal effects to activate the Co/SBA-15 catalyst,was employed for toluene removal.Specifically,Co/SBA-15 catalysts are closely positioned to the ground electrode of the plasma zone and can be heated and activated by the thermal effect when the voltage exceeds 10 k V.At12.4 k V,the temperature in the catalyst zone reached 261℃ in the DBD-TCC system,resulting in an increase in toluene degradation efficiency of 17%,CO_(2)selectivity of 21.2%,and energy efficiency of 27%,respectively,compared to the DBD system alone.In contrast,the DBD thermally-unconducted catalysis(DBD-TUC)system fails to enhance toluene degradation due to insufficient heat absorption and catalytic activation,highlighting the crucial role of AC-DBD generated heat in the activation of the catalyst.Furthermore,the degradation pathway and mechanism of toluene in the DBD-TCC system were hypothesized.This work is expected to provide an energy-efficient approach for high-frequency AC-DBD plasma removal of VOCs.

An Experimental Observation of the Thermal Effects and NO Emissions during Dissociation and Oxidation of Ammonia in the Presence of a Bundle of Thermocouples in a Vertical Flow Reactor

Ammonia (NH3) dissociation and oxidation in a cylindrical quartz reactor has been experimentally studied for various inlet NH3 concentrations (5%, 10%, and 15%) and reactor temperatures between 700 K and 1000 K. The thermal effects during both NH3 dissociation (endothermic) and oxidation (exothermic) were observed using a bundle of thermocouples positioned along the central axis of the quartz reactor, while the corresponding NH3 conversions and nitrogen oxides emissions were determined by analysing the gas composition of the reactor exit stream. A stronger endothermic effect, as indicated by a greater temperature drop during NH3 dissociation, was observed as the NH3 feed concentration and reactor temperature increased. During NH3 oxidation, a predominantly greater exothermic effect with increasing NH3 feed concentration and reactor temperature was also evident;however, it was apparent that NH3 dissociation occurred near the reactor inlet, preceding the downstream NH3 and H2 oxidation. For both NH3 dissociation and oxidation, NH3 conversion increased with increasing temperature and decreasing initial NH3 concentration. Significant levels of NOX emissions were observed during NH3 oxidation, which increased with increasing temperature. From the experimental results, it is speculated that the stainless-steel in the thermocouple bundle may have catalysed NH3 dissociation and thus changed the reaction chemistry during NH3 oxidation.

Atomistic simulation of thermal effects and defect structures during nanomachining of copper

Molecular dynamics （MD） simulations of monocrystalline copper （100） surface during nanomachining process were performed based on a new 3D simulation model. The material removal mechanism and system temperature distribution were discussed. The simulation results indicate that the system temperature distribution presents a roughly concentric shape, a steep temperature gradient is observed in diamond cutting tool, and the highest temperature is located in chip. Centrosymmetry parameter method was used to monitor defect structures. Dislocations and vacancies are the two principal types of defect structures. Residual defect structures impose a major change on the workpiece physical properties and machined surface quality. The defect structures in workpiece are temperature dependent. As the temperature increases, the dislocations are mainly mediated from the workpiece surface, while the others are dissociated into point defects. The relatively high cutting speed used in nanomachining results in less defect structures, beneficial to obtain highly machined surface quality.

Thermal Effects and RF Power Handling of DC～5GHz MEMS Switch

A DC to 5GHz series MEMS switch is designed and fabricated for wireless communication applications,and thermal effect and power handling of the series switch are discussed.The switch is made on glass substrate,and gold platinum contact is used to get a stable and little insert loss.From DC to 5GHz,0 6dB insertion loss,30dB isolation,and 30μs delay are demonstrated.Thermal effect of the switch is tested in 85℃ and -55℃ atmosphere separately.From DC to 4GHz,the insert loss of the switch increases 0 2dB in 85℃ and 0 4dB in -55℃,while the isolation holds the same value as that in room temperature.To measure the power handling capability of the switch,we applied a continuous RF power increasing from 10dBm to 35 1dBm with the step of 1 0dBm across the switch at 4GHz.The switch keeps working and shows a decrease of the insert loss for 0 1～0 6dB.The maximum continuous power handling (35 1dBm,about 3 24W) is higer than the reported value of shunt switch (about 420mW),which implies series switches have much better power handling capability.

Thermal effects on clay rocks for deep disposal of high-level radioactive waste

Thermal effects on the Callovo-Oxfordian and Opalinus clay rocks for hosting high-level radioactive waste were comprehensively investigated with laboratory and in situ experiments under repository relevant conditions:(1) stresses covering the range from the initial lithostatic state to redistributed levels after excavation,(2) hydraulic drained and undrained boundaries, and(3) heating from ambient temperature up to 90℃-120℃ and a subsequent cooling phase. The laboratory experiments were performed on normal-sized and large hollow cylindrical samples in various respects of thermal expansion and contraction, thermally-induced pore water pressure, temperature influences on deformation and strength, thermal impacts on swelling, fracture sealing and permeability. The laboratory results obtained from the samples are consistent with the in situ observations during heating experiments in the underground research laboratories at Bure and Mont-Terri. Even though the claystones showed significant responses to thermal loading, no negative effects on their favorable barrier properties were observed.

Analysis of Thermal Effects in Laser Rod Pumped by Repetitively Pulsed Laser Diode Array

Based on some assumptions, the numerical model of thermal distribution in solid state laser crystal pumped by pulsed laser diode is set up due to the pumped intensity distribution. Taking into account the property of YAG materials that varies with temperature, the transient temperature distribution of the laser crystal is calculated using finite element method on condition that K is a constant and a function of temperature. Then, the influence of the pumping parameters on the thermal effect in laser crystal is also discussed. This study is helpful to optimize the design of the diode side pumped solid state lasers.

Thermal Effects on Composition of Rearranged Hopanes in Hydrocarbon Source Rocks

Objective The distribution characteristics and formation mechanism of rearranged hopanes in hydrocarbon source rocks are affected by various geological conditions.Among these geological conditions,thermal action has an important influence on the formation of rearranged hopanes,which has been however little documented previously.

Comparison of the Thermomagnetic and Thermal Effects duringNanocrystallization of Amorphous Fe_(76.5-x)Cu_1Nb_xSi_(13.5)B_9 Alloys

The results of thermomagnetic (TM) and calorimetric (DSC) measurements have been compared in order to clarify some details of the mechanism of nanophase-formation from Finemet-type precursors with different Nb contents. It was found that the main features of the DSC thermograms (shape, relative separation and amplitude of the exothermic peaks characteristic for the precipitation of the Fe-(Si) solid solution and the transition metal borides) depend mainly on the composition of the precursor glass, and are only slightly affected by the heating rate between 20 and 80 K/min. The amplitude of the uprise of the magnetization in the TM curves (attributed to the precipitation of bcc-Fe(Si) and borides) decreases with increasing Nb-content. The Curietemperature of the precursor glasses. Tc(am1), the remainder amorphous phases, Tc(am2) and the bcc nanophase, Tc(n-Fe) are determined from the thermomagnetic curves. The shape of the TM curves is interpreted on the basis of the reactions describing the crystalIization of the hypo-eutectic Fe-B glasses.

Identification of thermal effects involved in DSC experiment on Al-Cu-Mg-Ag alloys with high Cu:Mg ratio

Precipitation reactions in the differential scanning calorimetry （DSC） of an Al-Cu-Mg-Ag alloy were identified by analyzing the results from hardness test,electrical conductivity test,and transmission electron microscope （TEM） examination.It is discovered that thermal effects can be identified through selected area electron diffraction and bright-field images.The reaction peaks around 171,231,and 276℃ can be attributed to a structural rearrangement of coherent zones,to the precipitation of Ω phases,and to the precipitation of Ω and θ＇ and possible combination with the transition of θ＇→θ,respectively.In addition,the hardness and electrical conductivity of the alloy change proportionately with the progression of reactions during the heating process.This phenomenon can be attributed to the evolution of the micro-structure.

Maternal Thermal Effects on Female Reproduction and Hatchling Phenotype in the Chinese Skink(Plestiodon chinensis)

We maintained gravid Chinese skinks(Plestiodon chinensis) at three constant temperatures(25, 28 and 31 °C) during gestation, and randomly assigned eggs from each female to one of the same three temperatures for incubation to determine maternal thermal effects on female reproduction and hatchling phenotype. Maternal temperature affected egg-laying date, hatching success and hatchling linear size(snout-vent length, SVL) but not clutch size, egg size, egg component, and embryonic stage at laying. More specifically, females at higher temperatures laid eggs earlier than did those at low temperatures, eggs laid at 31 °C were less likely to hatch than those laid at 25 °C or 28 °C, and hatchlings from eggs laid at 31 °C were smaller in SVL. Our finding that maternal temperature(pre-ovipositional thermal condition) rather than incubation temperature(post-ovipositional thermal condition) affected hatching success indicated that embryos at early stages were more vulnerable to temperature than those at late stages. Our data provide an inference that moderate maternal temperatures enhance reproductive fitness in P. chinensis.

THERMAL EFFECTS OF BUILDING′S EXTERNAL SURFACES IN CITY——Characteristics of Heat Flux into and out of External Wall Surfaces

This study examined the thermal effects of building′s external wall surfaces, using observational data of spatial-temporal distribution of surface temperature, air temperature, and heat flux into and out of external surface. Results indicate that external wall surface temperature and nearby air temperature vary with the change of orientation, height and season. In general, the external wall surface temperature is lower near the ground, and is higher near the roof, than nearby air temperature. But north wall surface temperature is mostly lower than nearby air temperature at the same height; south wall surface temperature during the daytime in December, and west wall surface temperature all day in August, is respectively higher than nearby air temperature. The heat fluxes into and out of external wall surfaces show the differences that exist in the various orientations, heights and seasons. In December, south wall surface at the lower sites emits heat and north wall surface at the higher sites absorbs heat. In April, all external wall surfaces, emit heat near the ground and absorb heat near the roof. In August, west wall surface all day emits heat, and other wall surfaces just show the commensurate behavior with that in April.

Surface,Size and Thermal Effects in Alkali Metal with Core-Electron Binding-Energy Shifts

Consistency between density functional theory calculations and X-ray photoelectron spectroscopy measurements confirms our predications on the undercoordination-induced local bond relaxation and core level shift of alkali metal,which determine the surface,size and thermal properties of materials.Zone-resolved photoelectron spectroscopyanalysis method and bond order-length-strength theory can be utilized to quantify the physical parameters regarding bonding identities and electronic property of metal surfaces,which allows for the study of the core-electron binding-energy shifts in alkali metals.By employing these methods and first principle calculation in this work,we can obtain the information of bond and atomic cohesive energy of under-coordinated atoms at the alkali metal surface.In addition,the effect of size and temperature towards the binding-energy in the surface region can be seen from the view point of Hamiltonian perturbation by atomic relaxation with atomic bonding.

Simulation of continuous terahertz wave transient state thermal effects on static water

We report a numerical simulation of continuous terahertz beam induced transient thermal effects on static water. The terahertz wave used in this paper has a Gaussian beam profile. Based on the transient heat conduction equation, the finite element method （FEM） is utilized to calculate the temperature distribution. The simulation results show the dynamic process of temperature change in water during terahertz irradiation. After about 300 s, the temperature reaches a steady state with a water layer thickness of 5 mm and a beam radius of 0.25 mm. The highest temperature increase is 7 K/mW approximately. This work motivates further study on the interaction between terahertz wave and bio-tissue, which has a high water content.

Theoretical study on the effective thermal conductivity of silica aerogels based on a cross-aligned and cubic pore model

Aerogel nanoporous materials possess high porosity, high specific surface area, and extremely low density due to their unique nanoscale network structure. Moreover, their effective thermal conductivity is very low, making them a new type of lightweight and highly efficient nanoscale super-insulating material. However, prediction of their effective thermal conductivity is challenging due to their uneven pore size distribution. To investigate the internal heat transfer mechanism of aerogel nanoporous materials, this study constructed a cross-aligned and cubic pore model(CACPM) based on the actual pore arrangement of SiO_(2) aerogel. Based on the established CACPM, the effective thermal conductivity expression for the aerogel was derived by simultaneously considering gas-phase heat conduction, solid-phase heat conduction, and radiative heat transfer. The derived expression was then compared with available experimental data and the Wei structure model. The results indicate that, according to the model established in this study for the derived thermal conductivity formula of silica aerogel, for powdery silica aerogel under the conditions of T = 298 K, a_(2)= 0.85, D_(1)= 90 μm, ρ = 128 kg/m^(3), within the pressure range of 0–10^(5)Pa, the average deviation between the calculated values and experimental values is 10.51%. In the pressure range of 10^(3)–10^(4)Pa, the deviation between calculated values and experimental values is within 4%. Under these conditions, the model has certain reference value in engineering verification. This study also makes a certain contribution to the research of aerogel thermal conductivity heat transfer models and calculation formulae.

Theoretical analysis of thermal effects in fiber laser from the moment when pump is turned on to steady-state

A theoretical analysis of the pump-induced temperature change and associated thermal phase shift occurring in a fiber laser is presented. The temperature rise and thermal phase shift from the moment when pump is turned on to steady-state in fiber lasers, such as Yb-doped fiber laser, are numerical calculated. With the same parameters, the numerical solution is in good agreement with the finite-element （ANSYS software） simulation.

Modeling on mechanical behavior and damage evolution of single-lap bolted composite interference-fit joints under thermal effects

This paper reports the modeling method and outcomes of mechanical performance and damage evolution of single-lap bolted composite interference-fit joints under extreme temperatures.The anisotropic continuum damage model involving thermal effects is established on continuum damage mechanics which integrates the shear nonlinearity constitutive relations characterized by Romberg-Osgood equation.The temperature-induced modification of thermal strains and material properties is incorporated in stress-strain analysis,extended 3 D failure criteria and exponential damage evolution rules.The proposed model is calibrated and employed to simulate behavior of composite joints in interference fitting,bolt preloading,thermal and bearing loading processes,during which the influence of interference-fit sizes,preload levels,laminate layups and service temperatures is thoroughly investigated.The predicated interfacial behavior,bearing response and failure modes are in good agreement with experimental tests.The numerical model is even capable of reflecting some non-intuitive experimental findings such as residual stress relaxation and matrix softening at elevated temperatures.

Control measures for thermal effects during placement of span-scale girder segments on continuous steel box girder bridges

In this study, we examined the thermal effects throughout the process of the placement of span-scale girder segments on a 6×110-m continuous steel box girder in the Hong Kong-Zhuhai-Macao Bridge. Firstly, when a span-scale girder segment is temporarily stored in the open air, temperature gradients will significantly increase the maximum reaction force on temporary supports and cause local buckling at the bottom of the girder segment. Secondly, due to the temperature difference of the girder segments before and after girth-welding, some residual thermal deflections will appear on the girder segments because the boundary conditions of the structure are changed by the girth-welding. Thirdly, the thermal expansion and thermal bending of girder segments will cause movement and rotation of bearings, which must be considered in setting bearings. We propose control measures for these problems based on finite element method simulation with field-measured temperatures. The local buckling during open-air storage can be avoided by reasonably determining the appropriate positions of temporary supports using analysis of overall and local stresses. The residual thermal deflections can be overcome by performing girth-welding during a period when the vertical temperature difference of the girder is within 1 °C, such as after 22:00. Some formulas are proposed to determine the pre-set distances for bearings, in which the movement and rotation of the bearings due to dead loads and thermal loads are considered. Finally, the feasibility of these control measures in the placement of span-scale girder segments on a real continuous girder was verified: no local buckling was observed during open-air storage;the residual thermal deflections after girth-welding were controlled within 5 mm and the residual pre-set distances of bearings when the whole continuous girder reached its design state were controlled within 20 mm.

Influence of thermal effects on elastohydrodynamic(EHD) lubrication behavior at high speeds

This paper describes a study of point contact elastohydrodynamic(EHD)lubrication behavior at high speeds(up to 20 m s1).Central film thicknesses were measured by optical interferometry device.The influence of slide-roll ratio and operating temperature on the central film thickness was determined.The influence of thermal effects on the reduction of film thickness was discussed via the analysis of numerical simulation method considering thermal effects.Subsequently,the experimental data was used to amend a set of unified parameters for the thermal corrections for different types of oil at high speeds.

Output characteristics of high-power stimulated Brillouin scattering pulse compression enhanced by thermal effects based on HT270

Thermal effects are typically considered as obstacles to high-repetition-rate stimulated Brillouin scattering(SBS)pulse compression.In this paper,a novel method is proposed for improving the SBS output characteristics by exploiting thermal effects on the liquid medium.Using HT270,the SBS output parameters with the medium purification and rotating off-centered lens methods are studied at different repetition rates.The results indicate that these two methods can alleviate thermal effects and improve the energy efficiency,but the rotating method reduces the energy stability because of the aggravated optical breakdown at the kilohertz-level repetition rate.For a 35-mJ pump energy,the energy efficiency at 2 kHz without the rotating method is 30%higher than that at 100 Hz and 70%higher than that at 500 Hz.The enhancement of the SBS output characteristics by thermal effects is demonstrated theoretically and experimentally,and 2-kHz high-power SBS pulsecompression is achieved with HT270.

Laser-enhanced thermal effects during focused ultrasound radiation on biological tissues

The thermal effects induced by a moderate intensity focused ultrasound and enhanced by combined laser pulses for bio-tissues and tissue-phantom are studied experimentally and theoretically. At first, the heating effects of bio-tissues and tissue-phantom induced by ultrasound and enhanced by laser are measured experimentally. The heating processes induced by attenuations of focused ultrasonic waves and cavitation effects of the focused ultrasound and combined laser are analyzed theoretically. By analyzing the mechanisms of these effects, it is found that the laser nucleation makes the cavitation bubble generation more easily, which can effectively enhance the ultrasonic cavitation effects, and then enhance the thermal effects of the samples. On the other hand, to evaluate quantitatively the heating processes induced by the focused ultrasound and enhanced by the pulsed laser, by fitting the theoretical calculations to the experimental results, the corresponding cavitation bubbles and rising temperatures induced by the focused ultrasound with and without laser can be estimated approximately.