Properties of Ultra-low Thermal Expansion LAS Transparent Glass-ceramics Prepared by Spodumene

The glass-ceramics were prepared with the spodumene mineral as the main raw material,and the effects of ZrO_(2)replacing TiO_(2)on the samples were systematically investigated.The results show that the substitution of ZrO_(2)for TiO_(2)is not conductive to precipitate𝛽β-quartz solid solution phase,but can improve the transparency and flexural strength of glass-ceramics.And the glass-ceramic with the highest visible light transmittance(87%)and flexural strength(231.80 MPa)exhibits an ultra-low thermal expansion of-0.028×10^(-7)K^(-1)in the region of 30-700℃.

Improvement strategy on thermophysical properties of A_(2)B_(2)O_(7)-type rare earth zirconates for thermal barrier coatings applications:A review

The A_(2)B_(2)O_(7)-type rare earth zirconate compounds have been considered as promising candidates for thermal barrier coating(TBC) materials because of their low sintering rate,improved phase stability,and reduced thermal conductivity in contrast with the currently used yttria-partially stabilized zirconia (YSZ) in high operating temperature environments.This review summarizes the recent progress on rare earth zirconates for TBCs that insulate high-temperature gas from hot-section components in gas turbines.Based on the first principles,molecular dynamics,and new data-driven calculation approaches,doping and high-entropy strategies have now been adopted in advanced TBC materials design.In this paper,the solid-state heat transfer mechanism of TBCs is explained from two aspects,including heat conduction over the full operating temperature range and thermal radiation at medium and high temperature.This paper also provides new insights into design considerations of adaptive TBC materials,and the challenges and potential breakthroughs are further highlighted for extreme environmental applications.Strategies for improving thermophysical performance are proposed in two approaches:defect engineering and material compositing.

The Negative Thermal Expansion Property of NdMnO_(3) Based on Pores Effect and Phase Transition

A novel negative thermal expansion(NTE) material NdMnO_(3) was synthesized by solid-state method at 1 523 K. The crystal structure, phase transition, pores effect and negative expansion properties of NdMnO_(3) were investigated by variable temperature X-ray diffraction(XRD), scanning electron microscope(SEM) and variable temperature Raman spectra. The compound exhibits NTE properties in the orderly O' phase crystal structure. When the temperature is from 293 to 759 K, the ceramic NdMnO_(3) shows negative thermal expansion of-4.7×10^(-6)/K. As temperature increases, the ceramic NdMnO_(3) presents NTE property range from 759 to 1 007 K. The average linear expansion coefficient is-18.88×10^(-6)/K. The physical mechanism of NTE is discussed and clarified through experiments.

Modification of streamer-to-leader transition model based on radial thermal expansion in the sphere-plane gap discharge at high altitude

Historically,streamer-to-leader transition studies mainly focused on the rod-plane gap and low altitude analysis,with limited attention paid to the sphere-plane gap at high altitude analysis.In this work,sphere-plane gap discharge tests were carried out under the gap distance of 5 m at the Qinghai Ultra High Voltage(UHV)test base at an altitude of 2200 m.The experiments measured the physical parameters such as the discharge current,electric field intensity and instantaneous optical power.The duration of the dark period and the critical charge of streamer-toleader transition were obtained at high altitude.Based on radial thermal expansion of the streamer stem,we established a modified streamer-to-leader transition model of the sphere-plane gap discharge at high altitude,and calculated the stem temperature,stem radii and the duration of streamer-to-leader transition.Compared with the measured duration of sphere-plane electrode discharge at an altitude of 2200 m,the error rate of the modified model was 0.94%,while the classical model was 6.97%,demonstrating the effectiveness of the modified model.From the comparisons and analysis,several suggestions are proposed to improve the numerical model for further quantitative investigations of the leader inception.

Tailoring of thermal expansion and phase transition temperature of ZrW_(2)O_8 with phosphorus and enhancement of negative thermal expansion of ZrW_(1.5)P_(0.5)O_(7.75)

ZrW_(2)O_(8)is a typical isotropic negative thermal expansion material with cubic structure.However,quenching preparation,pressure phase transition and metastable structure influence its practical applications.Adopting P to part-substitute W for ZrW_(2-x)P_(x)O_(8-0.5x)has decreased the sintering temperature and avoided the quenching process.When x=0.1,ZrW_(1.9)P_(0.1)O_(7.95)with a stable cubic structure can be obtained at 1150℃.The thermal expansion coefficient is tailored with the P content,and phase transition temperature is lowered.When x=0.5,thermal expansion coefficient attains-13.6×10^(-6)℃^(-1),ZrW_(1.5)P_(0.5)O_(7.75)exhibits enhance negative thermal expansion property.The difference of electronegativity leads to the decrease of phase transition temperature with the increase of P content.The different radii of ions lead to new structure of materials when P substitutes more.The results suggest that the P atom plays the stabilization role in the crystal structure of ZrW_(2-x)P_(x)O_(8-0.5x).

Thermal expansivity of geikielite and ilmenite utilizing in-situ synchrotron X-ray diffraction at high temperature

The unit-cell parameters and volumes of geikielite(MgTiO_(3))and ilmenite(FeTiO_(3))were investigated at high temperatures up to 700 K and ambient pressure,using in-situ angle-dispersive synchrotron X-ray diffraction.No phase transition was detected over the experimental temperature range.Using(Berman in J Petrol29:445-522,1988.10.1093/petrology/29.2.445)equations to fit the temperature-volume data,the volumetric thermal expansion coefficients at ambient conditions(α_(V0))of MgTiO_(3) and FeTiO_(3) were obtained as follows:2.55(6)×10^(-5)K^(-1)and 2.82(10)×10^(-5)K^(-1),respectively.We infer that the larger effective ionic radius of Fe^(2+)(Ⅵ)(0.78 A)than that of Mg^(2+)(Ⅵ)(0.72?)renders FeTiO_(3)has a larger volumetric thermal expansivity than MgTiO_(3).Simultaneously,the refined axial thermal expansion coefficients under ambient conditions areα_(a0)=0.74(3)×10^(-5)K^(-1)andα_(c0)=1.08(5)×10^(-5)K^(-1)for the aaxis and c-axis of MgTiO_(3),respectively,andα_(a0)=0.95(5)×10^(-5)K^(-1)andα_(c0)=0.92(12)×10^(-5)K^(-1)for the aaxis and c-axis of FeTiO_(3),respectively.The axial thermal expansivity of MgTiO_(3) is anisotropic,but that of FeTiO_(3) is nearly isotropic.We infer that the main reason for the different axial thermal expansivity between MgTiO_(3) and FeTiO_(3) is that the thermal expansion mode of the Mg-O bond in MgTiO_(3) is different from that of the Fe-O bonds in FeTiO_(3).

Statics, vibration, and buckling of sandwich plates with metamaterial cores characterized by negative thermal expansion and negative Poisson's ratio

This paper proposes a three-dimensional(3D)Maltese cross metamaterial with negative Poisson’s ratio(NPR)and negative thermal expansion(NTE)adopted as the core layers in sandwich plates,and aims to explore the relations between the mechanical responses of sandwich composites and the NPR or NTE of the metamaterial.First,the NPR and NTE of the metamaterial are derived analytically based on energy conservation.The effective elastic modulus and mass density of the 3D metamaterial are obtained and validated by the finite element method(FEM).Subsequently,the general governing equation of the 3D sandwich plate under thermal environments is established based on Hamilton’s principle with the consideration of the von Kármán nonlinearity.The differential quadrature(DQ)FEM(DQFEM)is utilized to obtain the numerical solutions.It is shown that NPR and NTE can enhance the global stiffness of sandwich structures.The geometric parameters of the Maltese cross metamaterial significantly affect the responses of the thermal stress,natural frequency,and critical buckling load.

Anisotropic thermal expansion in high-entropy multicomponent AlB_(2)-type diboride solid solutions

High-entropy(HE)ultra-high temperature ceramics have the chance to pave the way for future applications propelling technology advantages in the fields of energy conversion and extreme environmental shielding.Among others,HE diborides stand out owing to their intrinsic anisotropic layered structure and ability to withstand ultra-high temperatures.Herein,we employed in-situ high-resolution synchrotron diffraction over a plethora of multicomponent compositions,with four to seven transition metals,with the intent of understanding the thermal lattice expansion following different composition or synthesis process.As a result,we were able to control the average thermal expansion(TE)from 1.3×10^(−6)to 6.9×10^(−6)K^(−1)depending on the combination of metals,with a variation of in-plane to out-of-plane TE ratio ranging from 1.5 to 2.8.

Evaluating thermal expansion in fluorides and oxides:Machine learning predictions with connectivity descriptors

Open framework structures(e.g.,ScF_(3),Sc_(2)W_(3O)_(12),etc.)exhibit significant potential for thermal expansion tailoring owing to their high atomic vibrational degrees of freedom and diverse connectivity between polyhedral units,displaying positive/negative thermal expansion(PTE/NTE)coefficients at a certain temperature.Despite the proposal of several physical mechanisms to explain the origin of NTE,an accurate mapping relationship between the structural–compositional properties and thermal expansion behavior is still lacking.This deficiency impedes the rapid evaluation of thermal expansion properties and hinders the design and development of such materials.We developed an algorithm for identifying and characterizing the connection patterns of structural units in open-framework structures and constructed a descriptor set for the thermal expansion properties of this system,which is composed of connectivity and elemental information.Our developed descriptor,aided by machine learning(ML)algorithms,can effectively learn the thermal expansion behavior in small sample datasets collected from literature-reported experimental data(246 samples).The trained model can accurately distinguish the thermal expansion behavior(PTE/NTE),achieving an accuracy of 92%.Additionally,our model predicted six new thermodynamically stable NTE materials,which were validated through first-principles calculations.Our results demonstrate that developing effective descriptors closely related to thermal expansion properties enables ML models to make accurate predictions even on small sample datasets,providing a new perspective for understanding the relationship between connectivity and thermal expansion properties in the open framework structure.The datasets that were used to support these results are available on Science Data Bank,accessible via the link https://doi.org/10.57760/sciencedb.j00113.00100.

Thermal expansion behavior of sintered Nd–Fe–B magnets with different Co contents and orientations

The thermal expansion behavior of sintered Nd–Fe–B magnets is a crucial parameter for production and application.However, this aspect has not been thoroughly investigated. In this study, three different sintered Nd–Fe–B magnets with varying Co content(Co = 0, 6, 12 wt%) were prepared using the conventional powder metallurgy method, and four magnets oriented under different magnetic fields were prepared to compare. The thermal expansion behavior for the magnets was investigated using a linear thermal dilatometry in the temperature range of 20℃–500℃. It was found that, the coefficient of thermal expansion(CTE) increases with the increase of Co contents, while the anisotropy of thermal expansion decreases.The introduction of Co leads to continuous changes from negative to positive thermal expansion in the vertically oriented direction, which is important for the development of zero thermal expansion magnets. The thermal expansion of nonoriented magnets was found to be isotropic. Additionally, the anisotropy of thermal expansion increases with the increase of orientation degree. These results have important implications for the development of sintered Nd–Fe–B with controllable CTE.

Negative thermal expansion and phase transition of low-temperature Mg_(2)NiH_(4)

The negative thermal expansion(NTE) phenomenon is of great significance in fabricating zero thermal expansion(ZTE) materials to avoid thermal shock during heating and cooling. NTE is observed in limited groups of materials, e.g., metal cyanides, oxometallates, and metalorganic frameworks, but has not been reported in the family of metal hydrides. Herein, a colossal and continuous negative thermal expansion is firstly developed in the low-temperature phases of LT1-and LT2-Mg_(2)NiH_(4) between 488 K and 733 K from in-situ transmission electron microscope(TEM) video, with the volume contraction reaching 18.7% and 11.3%, respectively. The mechanisms for volume contraction of LT1 and LT2 phases are elucidated from the viewpoints of phase transformation, magnetic transition, and dehydrogenation, which is different from common NTE materials containing flexible polyhedra units in the structure. The linear volume shrinkage of LT2 in the temperature of 488-553 K corresponds to the phase transition of LT2→HT with a thermal expansion coefficient of -799.7 × 10^(-6) K^(-1) revealed by in-situ synchrotron powder X-ray diffraction. The sudden volume contraction in LT1 between 488 and 493 K may be caused by the rapid dehydrogenation of LT1 to Mg_(2)Ni. The revealed phenomenon in single composite material with different structures would be significant for preparing zero thermal expansion materials by tuning the fraction of LT1 and LT2 phases.

Magneto-volume effect in Fe_(n)Ti_(13-n)clusters during thermal expansion

Ab initio molecular dynamics calculations have been carried out to search for the ground state structure of Fe_(n)Ti_(13-n)clusters and measure the thermal expansion of Fe_(n)Ti_(13-n).The volume of Fe_(n)Ti_(13-n)clusters during thermal expansion is jointly determined by anharmonic interaction and magneto-volume effect.It has been found that Fe_(6)Ti_(7),Fe_9Ti_(4),Fe_(11)Ti_(2),and Fe_(13)clusters can exhibit the remarkable magneto-volume effect with abnormal volume behaviors and magnetic moment behaviors during thermal expansion.A prerequisite for the magneto-volume effect of Fe_(n)Ti_(13-n)clusters during thermal expansion has been revealed and the magnitude of the magneto-volume is also approximately determined.Furthermore,the magneto-volume behaviors of Fe_(n)Ti_(13-n)clusters are qualitatively characterized by the energy contour map.Our results shed light on the mechanism of the magneto-volume effect in Fe_(n)Ti_(13-n)clusters during thermal expansion,which can guide the design of nanomaterials with zero expansion or even controllable expansion properties.

Linear magnetoresistance and structural distortion in layered SrCu_(4-x)P_(2) single crystals

We report a systematic study on layered metal SrCu_(4-x)P_(2) single crystals via transport, magnetization, thermodynamic measurements and structural characterization. We find that the crystals show large linear magnetoresistance without any sign of saturation with a magnetic field up to 30T. We also observe a phase transition with significant anomalies in resistivity and heat capacity at T_(p)~140 K. Thermal expansion measurement reveals a subtle lattice parameter variation near Tp, i.e.,?L_(c)/L_(c)~0.062%. The structural characterization confines that there is no structure transition below and above T_(p). All these results suggest that the nonmagnetic transition of SrCu_(4-x)P_(2) could be associated with structural distortion.

DEVELOPMENT OF INCONEL~ ALLOY 783，A LOW THERMAL EXPANSION，CRACK GROWTH RESISTANT SUPERALLOY

Low thermal expansion superalloys have been used for a number of years in a variety of applications, including gas turbine engines. The low thermal expansion characteristics of the most widely used class of materials are derived from the ferromagnetic characteristics of Ni, Fe, and Co-based austenitic matrices containing little or no Cr.Alloy developments have been aimed at improving the oxidation resistance and stress accelerated grain boundary oxygen (SAGBO) attack.INCONEL alloy 783 is an oxidation resistant, low coefficient of thermal expansion superalloy developed for gas turbine applications. Alloy 783 represents a culmination in the development, of an alloy system with very high alumtnum content that, in addition to forming γ′,causes βaluminide phase precipitation in the austenitic matrix.This type of structure can be processed to resist both SAGBO and general oxidation,while providing low thermal expansion and useful mechanical properties up to 700℃.Key aspects of the alloy's development are presented.

Thermal expansion of kyanite at ambient pressure:An X-ray powder diffraction study up to 1000℃

The thermal expansion coefficients of kyanite at ambient pressure have been investigated by an X-ray powder diffraction technique with temperatures up to 1000 ℃. No phase transition was observed in the experimental temperature range. Data for the unit-cell parameters and temperatures were fitted empirically resulting in the following thermal expansion coefficients： αa = 5.8（3） × 10^-5, αb = 5.8 （1）× 10^-5, αc = 5.2（1）× 10^-5, and αv = 7.4（1） × 10^-3 ℃ 1 in good agreement with a recent neutron powder diffraction study. On the other hand, the variation of the unit-cell angles α, β and γ of kyanite with increase in temperature is very complicated, and the agreement among all studies is poor. The thermal expansion data at ambient pressure reported here and the compression data at ambient temperature from the literature suggest that, for the kyanite lattice, the most and least thermally expandable directions correspond to the most and least compressible directions, respectively.

Effects of cryogenic treatment on the thermal physical properties of Cu_(76.12) Al_(23.88) alloy

The thermal diffusion coefficient, heat capacity, thermal conductivity, and thermal expansion coefficient of Cu76.12Al23.88 alloy before and after cryogenic treatment in the heating temperature range of 25℃ to 600℃ were measured by thermal constant tester and thermal expansion instrument. The effects of cryogenic treatment on the thermal physical properties of CU76,12A123,88 alloy were investigated by comparing the variation of the thermal parameters before and after cryogenic treatment. The results show that the variation trend of the thermal diffusion coefficient, heat capacity, thermal conductivity, and thermal expansion coefficient of CU76.12Al23.88 alloy after cryogenic treatment was the same as before. The cryogenic treatment can increase the thermal diffusion coefficient, thermal conductivity, and thermal expansion coeffi- cient of Cu76.12Al23.88 alloy and decrease its heat capacity. The maximum difference in the thermal diffusion coefficient between the before and after cryogenic treatment appeared at 400℃. Similarly, thermal conductivity was observed at 200℃.

Microstructure and thermal properties of copper matrix composites reinforced with titanium-coated graphite fibers

Milled form of mesophase pitch-based graphite fibers were coated with a titanium layer using chemical vapor deposition technique and Ti-coated graphite fiber/Cu composites were fabricated by hot-pressing sintering. The composites were characterized with X-ray diffraction, scanning/transmission electron microscopies, and by mea- suring thermal properties, including thermal conductivity and coefficient of thermal expansion （CTE）. The results show that the milled fibers are preferentially oriented in a plane perpendicular to the pressing direction, leading to anisotropic thermal properties of the composites. The Ti coating reacted with graphite fiber and formed a continuous and uniform TiC layer. This carbide layer establishes a good metallurgical interracial bonding in the composites, which can improve the thermal properties effectively. When the fiber content ranges from 35 vol% to 50 vol%, the in-plane thermal conductivities of the composites increase from 383 to 407 W.（m.K）-~, and the in-plane CTEs decrease from 9.5 x 10-6 to 6.3 10-6 K-1.

Effects of boron on the microstructure and thermal properties of Cu/diamond composites prepared by pressure infiltration

Diamond reinforced copper（Cu/diamond） composites were prepared by pressure infiltration for their application in thermal management where both high thermal conductivity and low coefficient of thermal expansion（CTE） are important.They were characterized by the microstructure and thermal properties as a function of boron content,which is used for matrix-alloying to increase the interfacial bonding between the diamond and copper.The obtained composites show high thermal conductivity（660 W/（m·K）） and low CET（7.4×10-6 K-1） due to the formation of the B13C2 layer at the diamond-copper interface,which greatly strengthens the interfacial bonding.Thermal property measurements indicate that in the Cu-B/diamond composites,the thermal conductivity and the CTE show a different variation trend as a function of boron content,which is attributed to the thickness and distribution of the interfacial carbide layer.The CTE behavior of the present composites can be well described by Kerner＇s model,especially for the composites with 0.5wt% B.

Evaluation of the microstructure,thermal and mechanical properties of Cu/SiC nanocomposites fabricated by mechanical alloying

Nano-sized silicon carbide(SiC:0wt%,1wt%,2wt%,4wt%,and 8wt%)reinforced copper(Cu)matrix nanocomposites were manufactured,pressed,and sintered at 775 and 875℃in an argon atmosphere.X-ray diffraction(XRD)and scanning electron microscopy were performed to characterize the microstructural evolution.The density,thermal expansion,mechanical,and electrical properties were studied.XRD analyses showed that with increasing SiC content,the microstrain and dislocation density increased,while the crystal size decreased.The coefficient of thermal expansion(CTE)of the nanocomposites was less than that of the Cu matrix.The improvement in the CTE with increasing sintering temperature may be because of densification of the microstructure.Moreover,the mechanical properties of these nanocomposites showed noticeable enhancements with the addition of SiC and sintering temperatures,where the microhardness and apparent strengthening efficiency of nanocomposites containing 8wt%SiC and sintered at 875℃were 958.7 MPa and 1.07 vol%^(−1),respectively.The electrical conductivity of the sample slightly decreased with additional SiC and increased with sintering temperature.The prepared Cu/SiC nanocomposites possessed good electrical conductivity,high thermal stability,and excellent mechanical properties.

A novel implementation algorithm of asymptotic homogenization for predicting the effective coefficient of thermal expansion of periodic composite materials

Asymptotic homogenization (AH) is a general method for predicting the effective coefficient of thermal expansion (CTE) of periodic composites. It has a rigorous mathematical foundation and can give an accurate solution if the macrostructure is large enough to comprise an infinite number of unit cells. In this paper, a novel implementation algorithm of asymptotic homogenization (NIAH) is developed to calculate the effective CTE of periodic composite materials. Compared with the previous implementation of AH, there are two obvious advantages. One is its implementation as simple as representative volume element (RVE). The new algorithm can be executed easily using commercial finite element analysis (FEA) software as a black box. The detailed process of the new implementation of AH has been provided. The other is that NIAH can simultaneously use more than one element type to discretize a unit cell, which can save much computational cost in predicting the CTE of a complex structure. Several examples are carried out to demonstrate the effectiveness of the new implementation. This work is expected to greatly promote the widespread use of AH in predicting the CTE of periodic composite materials.