Thermal behavior of integrated passive components has become an important issue when designing these components. This paper presents the thermal modeling of a multilayer integrated LC filter used in DC-DC step-down co...Thermal behavior of integrated passive components has become an important issue when designing these components. This paper presents the thermal modeling of a multilayer integrated LC filter used in DC-DC step-down converter for temperature distribution calculation. The approach used for this analysis is based on thermal equivalent circuit. Temperature distribution is obtained from algebraic equation, which is in vector and matrix form. The results of analytical calculation are compared with simulation results from finite element method. These results showed a good correlation.展开更多
A combined conduction and radiation heat transfer model was used to simulate the heat transfer within wafer and investigate the effect of thermal transport properties on temperature non-uniformity within wafer surface...A combined conduction and radiation heat transfer model was used to simulate the heat transfer within wafer and investigate the effect of thermal transport properties on temperature non-uniformity within wafer surface. It is found that the increased conductivities in both doped and undoped regions help reduce the temperature difference across the wafer surface. However, the doped layer conductivity has little effect on the overall temperature distribution and difference. The temperature level and difference on the top surface drop suddenly when absorption coefficient changes from 104 to 103 m-1. When the absorption coefficient is less or equal to 103 m-1, the temperature level and difference do not change much. The emissivity has the dominant effect on the top surface temperature level and difference. Higher surface emissivity can easily increase the temperature level of the wafer surface. After using the improved property data, the overall temperature level reduces by about 200 K from the basis case. The results will help improve the current understanding of the energy transport in the rapid thermal processing and the wafer temperature monitor and control level.展开更多
Heating the whole space,which is currently used in northern China,leads to high energy consumption and substantial pollution.A transition to local heating has the potential to help address this problem.In this paper,t...Heating the whole space,which is currently used in northern China,leads to high energy consumption and substantial pollution.A transition to local heating has the potential to help address this problem.In this paper,the effects of radiator-related parameters(position,power,and size)and room-related parameters(aspect ratio and height)on local heating were studied.Two evaluation indices,the effective coefficient of operative temperature(OTEC)and the effective coefficient of local heating(LHEC),were proposed.In addition,the heat source-control core-area(HSCCA)was proposed,and the effect range of heat sources in the space was evaluated by the attenuation of operative temperature.The findings demonstrated that the radiator position has a greater influence on local heating than size.When the position of the radiator was changed from"close to the inner wall"to"close to the outer wall",the LHEC(the interior one-quarter of room is a local heating zone)was found to decrease by 73%.The size of the radiator,which is close to the inner wall,doubled or quadrupled,and the LHEC increased by 9%and 18%.Moreover,rooms with a larger aspect ratio or small room height were found to be the most optimal for local heating applications.The area of the HSCCA decreased as the position of the radiator approached the outer wall.The findings of this study can be used as a design reference for the radiator when the heating mode changes from"full-space heating"to"local heating".展开更多
Defects in cast-in-situ piles have an adverse impact on load transfer at the pile‒soil interface and pile bearing capacity. In recent years, thermal integrity profiling (TIP) has been developed to measure temperature ...Defects in cast-in-situ piles have an adverse impact on load transfer at the pile‒soil interface and pile bearing capacity. In recent years, thermal integrity profiling (TIP) has been developed to measure temperature profiles of cast-in-situ piles, enabling the detection of structural defects or anomalies at the early stage of construction. However, using this integrity testing method to evaluate potential defects in cast-in-situ piles requires a comprehensive understanding of the mechanism of hydration heat transfer from piles to surrounding soils. In this study, small-scale model tests were conducted in laboratory to investigate the performance of TIP in detecting pile integrity. Fiber-optic distributed temperature sensing (DTS) technology was used to monitor detailed temperature variations along model piles in sand. Additionally, sensors were installed in sand to measure water content and matric suction. An interpretation method against available DTS-based thermal profiles was proposed to reveal the potential defective regions. It shows that the temperature difference between normal and defective piles is more obvious in wet sand. In addition, there is a critical zone of water migration in sand due to the water absorption behavior of cement and temperature transfer-induced water migration in the early-age concrete setting. These findings could provide important insight into the improvement of the TIP testing method for field applications.展开更多
A time-resolved numerical computational approach, involving the combustion of double-base propellant is performed on thermal protection material for SRM nozzle. An implicit Navier-Stokes Solver is selected to simulate...A time-resolved numerical computational approach, involving the combustion of double-base propellant is performed on thermal protection material for SRM nozzle. An implicit Navier-Stokes Solver is selected to simulate two-dimensional axial-symmetric unsteady turbulent flow of compressible fluid. The governing equations are discredited by using the finite Volume method. S-A turbulence model is employed. CFD scheme is implemented to investigate the temperature distribution causes at nozzle throat inserts composite material. Different parameters have been selected for the analysis to validate the temperature variation in the throat inserts and baking material of SRM nozzle. The advanced SRM nozzle composite material is also characterized for the high thermo stability and high thermo mechanical capabilities to make it more reliable, simpler and lighter.展开更多
A two-dimensional model is suggested for calculation of thermal radiation and temperature profile on integrated four-nozzle surfaces of a spacecraft. Correlation between temperature increase with geometry and emissivi...A two-dimensional model is suggested for calculation of thermal radiation and temperature profile on integrated four-nozzle surfaces of a spacecraft. Correlation between temperature increase with geometry and emissivity is obtained through comprehensive computation.Results of the correlation agree with data from three-dimensional calculation. Correlationsfor twin cylinders and plates with infinitive length are also proposed.展开更多
文摘Thermal behavior of integrated passive components has become an important issue when designing these components. This paper presents the thermal modeling of a multilayer integrated LC filter used in DC-DC step-down converter for temperature distribution calculation. The approach used for this analysis is based on thermal equivalent circuit. Temperature distribution is obtained from algebraic equation, which is in vector and matrix form. The results of analytical calculation are compared with simulation results from finite element method. These results showed a good correlation.
基金Project(N110204015)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2012M510075)supported by the China Postdoctoral Science Foundation
文摘A combined conduction and radiation heat transfer model was used to simulate the heat transfer within wafer and investigate the effect of thermal transport properties on temperature non-uniformity within wafer surface. It is found that the increased conductivities in both doped and undoped regions help reduce the temperature difference across the wafer surface. However, the doped layer conductivity has little effect on the overall temperature distribution and difference. The temperature level and difference on the top surface drop suddenly when absorption coefficient changes from 104 to 103 m-1. When the absorption coefficient is less or equal to 103 m-1, the temperature level and difference do not change much. The emissivity has the dominant effect on the top surface temperature level and difference. Higher surface emissivity can easily increase the temperature level of the wafer surface. After using the improved property data, the overall temperature level reduces by about 200 K from the basis case. The results will help improve the current understanding of the energy transport in the rapid thermal processing and the wafer temperature monitor and control level.
基金The research was supported by the National Natural Science Foundation of China(No.52078408)the Science Foundation for Outstanding Youth of Shaanxi Province(2020JC-43).
文摘Heating the whole space,which is currently used in northern China,leads to high energy consumption and substantial pollution.A transition to local heating has the potential to help address this problem.In this paper,the effects of radiator-related parameters(position,power,and size)and room-related parameters(aspect ratio and height)on local heating were studied.Two evaluation indices,the effective coefficient of operative temperature(OTEC)and the effective coefficient of local heating(LHEC),were proposed.In addition,the heat source-control core-area(HSCCA)was proposed,and the effect range of heat sources in the space was evaluated by the attenuation of operative temperature.The findings demonstrated that the radiator position has a greater influence on local heating than size.When the position of the radiator was changed from"close to the inner wall"to"close to the outer wall",the LHEC(the interior one-quarter of room is a local heating zone)was found to decrease by 73%.The size of the radiator,which is close to the inner wall,doubled or quadrupled,and the LHEC increased by 9%and 18%.Moreover,rooms with a larger aspect ratio or small room height were found to be the most optimal for local heating applications.The area of the HSCCA decreased as the position of the radiator approached the outer wall.The findings of this study can be used as a design reference for the radiator when the heating mode changes from"full-space heating"to"local heating".
基金The authors grate fully acknowledge the financial support provided by the National Natural Science Foundation of China(Grant Nos.42225702 and 42077235)the Open Research Project Program of the State Key Laboratory of Internet of Things for Smart City(University of Macao),China(Grant No.SKUoTSC(UM)-2021-2023/0RP/GA10/2022).
文摘Defects in cast-in-situ piles have an adverse impact on load transfer at the pile‒soil interface and pile bearing capacity. In recent years, thermal integrity profiling (TIP) has been developed to measure temperature profiles of cast-in-situ piles, enabling the detection of structural defects or anomalies at the early stage of construction. However, using this integrity testing method to evaluate potential defects in cast-in-situ piles requires a comprehensive understanding of the mechanism of hydration heat transfer from piles to surrounding soils. In this study, small-scale model tests were conducted in laboratory to investigate the performance of TIP in detecting pile integrity. Fiber-optic distributed temperature sensing (DTS) technology was used to monitor detailed temperature variations along model piles in sand. Additionally, sensors were installed in sand to measure water content and matric suction. An interpretation method against available DTS-based thermal profiles was proposed to reveal the potential defective regions. It shows that the temperature difference between normal and defective piles is more obvious in wet sand. In addition, there is a critical zone of water migration in sand due to the water absorption behavior of cement and temperature transfer-induced water migration in the early-age concrete setting. These findings could provide important insight into the improvement of the TIP testing method for field applications.
文摘A time-resolved numerical computational approach, involving the combustion of double-base propellant is performed on thermal protection material for SRM nozzle. An implicit Navier-Stokes Solver is selected to simulate two-dimensional axial-symmetric unsteady turbulent flow of compressible fluid. The governing equations are discredited by using the finite Volume method. S-A turbulence model is employed. CFD scheme is implemented to investigate the temperature distribution causes at nozzle throat inserts composite material. Different parameters have been selected for the analysis to validate the temperature variation in the throat inserts and baking material of SRM nozzle. The advanced SRM nozzle composite material is also characterized for the high thermo stability and high thermo mechanical capabilities to make it more reliable, simpler and lighter.
文摘A two-dimensional model is suggested for calculation of thermal radiation and temperature profile on integrated four-nozzle surfaces of a spacecraft. Correlation between temperature increase with geometry and emissivity is obtained through comprehensive computation.Results of the correlation agree with data from three-dimensional calculation. Correlationsfor twin cylinders and plates with infinitive length are also proposed.
