Significantly enhanced thermal stability of HMX by phase-transition lysozyme coating

A new robust bio-inspired route by using lysozyme aqueous solution for surface modification on 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX)was described in this paper.HMX crystals were coated by in situ phase transition of lysozyme(PTL)molecules.The HMX decorated by PTL was characterized by SEM,XRD,FTIR and XPS,demonstrating a dense core-shell coating layer.The coverage of lysozyme on HMX crystal was calculated by the ratio of sulfur content.The surface coverage increased from 60.5% to 93.5% when the content of PTL was changed from 0.5 wt% to 2.0 wt%,indicating efficient coating.The thermal stability of HMX was investigated by in situ XRD and DSC.The thermal phase transition temperature of HMX(β to δ phase)was delayed by 42℃ with 2.0 wt% PTL coating,which prevented HMX from thermal damage and sensitivity by the effect of PTL coating.After heating at 215℃,large cracks appeared in the naked HMX crystal,while the PTL coated HMX still maintained intact,with the impact energy of HMX dropped dramatically from 5 J to 2 J.However,the impact energy of HMX with 1.0 wt% and 2.0 wt% coating content(HMX@PTL-1.0 and HMX@PTL-2.0)was unchanged(5 J).Present results potentially enable large-scale fabrication of polymorphic energetic materials with outstanding thermal stability by novel lysozyme coating.

Construction of core@double-shell structured energetic composites with simultaneously enhanced thermal stability and safety performance

The poor thermal stability and high sensitivity severely hinder the practical application of hexanitrohexaazaisowurtzitane(CL-20).Herein,a kind of novel core@double-shell CL-20 based energetic composites were fabricated to address the above issues.The coordination complexes which consist of natural polyphenol tannic acid(TA) and Fe~Ⅲ were chosen to construct the inner shell,while the graphene sheets were used to build the outer shell.The resulting CL-20/TA-Fe~Ⅲ/graphene composites exhibited simultaneously improved thermal stability and safety performance with only 1 wt% double-shell content,which should be ascribed to the intense physical encapsulation effect from inner shell combined with the desensitization effect of carbon nano-materials from outer shell.The phase transition(ε to γ) temperature increased from 173.70 ℃ of pure CL-20 to 191.87℃ of CL-20/TA-Fe~Ⅲ/graphene composites.Meanwhile,the characteristic drop height(H_(50)) dramatically increased from 14.7 cm of pure CL-20 to112.8 cm of CL-20/TA-Fe~Ⅲ/graphene composites,indicating much superior safety performance after the construction of the double-shell structure.In general,this work has provided an effective and versatile strategy to conquer the thermal stability and safety issues of CL-20 and contributes to the future application of high energy density energetic materials.

Preparation and Thermal Stability of AlMoON Based Solar Selective Absorption Coating

AlMoON based solar selective absorption coatings were deposited on stainless steel substrate by magnetron sputtering.The coatings included infrared reflection layer Mo,absorption layer AlMoN,absorption layer AlMoON and antireflection layer AlMoO from bottom to top.The surface of the deposited coatings is flat without obvious defects.The absorptivity and emissivity are 0.896 and 0.09,respectively,and the quality factor is 9.96.After heat treatment at 500℃-36 h,the surface roughness of the coating increases,a small number of cracks and other defects appear,and the broken part is still attached to the coating surface.A certain degree of element diffusion occurs in the coatings,resulting in the decline of the optical properties of the coatings.The absorptivity and emissivity are 0.883 and 0.131,respectively,the quality factor is 7.06,and the PC value is 0.0335.The coatings do not fail under this condition and have certain thermal stability.

Thermal Stability and Degeneration Behavior of Solar Selective Absorber Based on WTi-Al_(2)O_(3)Cermet

A WTi-Al_(2)O_(3)cermet-based solar selective absorber was prepared to investigate the atomic diffusion induced spectral selectivity degeneration.The as-deposited coating exhibits superior absorptance(0.934)and low thermal emittance(0.098),as well as excellent thermal stability with a selectivity of 0.900/0.07 even after annealing at 923 K for 400 h in Ar ambient.However,the multilayer coating failed after being subjected to annealing at 923 K for 400 h in an air environment,as indicated by a decrease in solar absorptance to 0.912 and an increase in thermal emittance to 0.634.The microstructure characterizations reveal that the annealed coating exhibits a columnar morphology along the vertical direction of the substrate.The presence of abundant grain boundaries in the multilayer coating promotes the outward diffusion of Cr and Mn atoms in the stainless-steel substrate.The Mn atoms,in particular,possess the capability to migrate towards the surface of the coating and undergo an oxidation reaction with oxygen,facilitating the formation of a thick Mn_(2)O_(3)layer.The roughness of the coating surface was significantly increased in this case,adversely affecting solar absorptance due to amplified sunlight reflection.In addition,the rocketing of thermal emittance is attributed to the destabilization of W infrared reflective layer during the annealing.These findings highlight the importance of considering the outward diffusion of Mn and Cr elements in the stainless-steel substrate when optimizing solar selective absorbers.

The Effect of Uncaria gambir on Optical Properties and Thermal Stability of CNF/PVA Biocomposite Films

Cellulose-based film has gained popularity as an alternative to synthetic polymers due to its outstanding properties.Among all types of cellulose materials available,cellulose nanofiber(CNF)has great potential to be utilized in a diverse range of applications,including as a film material.In this study,CNF biocomposite film was prepared by using polyvinyl alcohol(PVA)as a matrix and Uncaria gambir extract as a filler.This study aims to investigate the effect of Uncaria gambir extract on the optical properties and thermal stability of the produced film.The formation of the CNF biocomposite films was confirmed using Fourier Transform Infrared Spectroscopy,their transmittance characteristics were measured using UV-Vis spectroscopy and a transmittance meter,while their reflectance was determined using a reflectance meter.The results revealed that the addition of Uncaria gambir extract to the CNF biocomposite film improved its UV-shielding properties,as indicated by the lower percentage of transmittance in the visible region,10%–70%.In addition,its reflectance increased to 10.6%compared to the CNF film without the addition of Uncaria gambir extract.Furthermore,the thermal stability of the CNF biocomposite film with the addition of Uncaria gambir extract improved to around 400℃–500℃.In conclusion,the results showed that CNF biocomposite film prepared by adding Uncaria gambir extract can be a promising candidate for optical and thermal management materials.

Further Analysis of Machine Tool Dimensional Accuracy and Thermal Stability under Varying Floor Temperature

Machining is as old as humanity, and changes in temperature in both the machine’s internal and external environments can be of great concern as they affect the machine’s thermal stability and, thus, the machine’s dimensional accuracy. This paper is a continuation of our earlier work, which aimed to analyze the effect of the internal temperature of a machine tool as the machine is put into operation and vary the external temperature, the machine floor temperature. Some experiments are carried out under controlled conditions to study how machine tool components get heated up and how this heating up affects the machine’s accuracy due to thermally induced deviations. Additionally, another angle is added by varying the machine floor temperature. The parameters mentioned above are explored in line with the overall thermal stability of the machine tool and its dimensional accuracy. A Robodrill CNC machine tool is used. The CNC was first soaked with thermal energy by gradually raising the machine floor temperature to a certain level before putting the machine in operation. The machine was monitored, and analytical methods were deplored to evaluate thermal stability. Secondly, the machine was run idle for some time under raised floor temperature before it was put into operation. Data was also collected and analyzed. It is observed that machine thermal stability can be achieved in several ways depending on how the above parameters are joggled. This paper, in conclusion, reinforces the idea of machine tool warm-up process in conjunction with a carefully analyzed and established machine floor temperature variation for the approximation of the machine tool’s thermally stability to map the long-time behavior of the machine tool.

Microstructure and interface thermal stability of C/Mo double-coated SiC fiber reinforced γ-TiAl matrix composites

C/Mo duplex coating interfacially modified SiC fiber-reinforced γ-TiAl matrix composite （SiCf/C/Mo/γ-TiA1） was prepared by foil-fiber-foil method to investigate its interfacial modification effect. SiCf/C/TiAl composites were also prepared under the same processing condition for comparision. Both kinds of the composites were thermally exposed in vacuum at 800 and 900℃ for different durations in order to study thermal stability of the interfacial zone. With the aids of scanning electron microscope （SEM） and energy dispersive spectrometer （EDS）, the interracial microstructures of the composites were investigated. The results reveal that, although adding the Mo coating, the interfacial reaction product of the SiCf/C/Mo/TiAl composite is the same with that of the SiCf/C/TiA1 composite, which is TiC/Ti2AlC between the coating and the matrix. However, C/Mo duplex coating is more efficient in hindering interfacial reaction than C single coating at 900 ℃ and below. In addition, a new layer of interfacial reaction product was found between Ti2AlC and the matrix after 900 ℃, 200 h thermal exposure, which is rich in V and close to the chemical composition of B2 phase.

Thermal stability,crystallization behavior,Vickers hardness and magnetic properties of Fe-Co-Ni-Cr-Mo-C-B-Y bulk metallic glasses

Thermal stability,crystallization behavior,Vickers hardness and magnetic properties of the Fe41Co7-xNixCr15Mo14C15B6Y2（x=0,1,3,5） bulk metallic glasses were investigated.The Fe41Co7-xNixCr15Mo14C15B6Y2（x=0,1,3,5） metallic glasses were fabricated by copper mold casting method.The thermal stability and crystallization behavior of the metallic glass rods were investigated by differential scanning calorimetry and isothermal experiments.Hardness measurements for samples annealed at different temperatures for different time were carried out at room temperature by the Vickers hardness tester,and magnetic measurements were performed at different temperatures by the vibrating sample magnetometer.It is shown that the addition of Ni does not play a positive role for enlarging ΔTx and GFA from parameter γ（=Tx/（Tg＋Tl））,and it can,however,increase the activation energy in the initial stage of crystallization by changing the initial crystallization behavior.The minor addition of Ni can refine the crystal grain obtained from the full crystallization experiment.The primary crystallization causes the decrease of hardness in these alloys,and as the crystallization continues,the hardness in all samples increases instead due to the precipitation of carbide and boride.The annealing temperature has an obvious effect on magnetic properties of these alloys,and the minor addition of Ni can effectively prevent the alloy annealed at high temperature to transform from paramagnetic to ferromagnetic state.

Thermal stability of electrodeposited nanocrystalline nickel assisted by flexible friction

Nanocrystalline nickel coating was prepared by flexible friction assisted electrodeposition technology in an additive-free Watts bath.The coating consists of massive equiaxial crystals with an average grain size of about 24 nm and exhibits a（111） preferred orientation.The differential scanning calorimetry（DSC） analysis of nanocrystalline nickel demonstrates that the peak temperature of rapid grain growth is about 285.4 °C,and the peak temperature of grain growth towards equilibrium is around 431.5 °C.The isochronous annealing results reveal that abnormal grain growth behavior is not observed in nanocrystalline nickel without sulfur-containing.The thermal stability of the deposition was improved due to its initial microstructure of the as-deposited nickel and a certain amount of annealing nano-twins with low-energy,which reduces the driving force for grain growth.Consequently,the coating shows a low residual tensile stress of about 50 MPa and a high microhardness of HV 400 at the annealing temperature of 450 °C.

Expression and Thermal Stability Analysis of Peat1 and the 3 Deletion Mutants

[Objective] The research aimed to reveal the functions of NAC and UBA domains in Peatl＇s thermal stability. [Method] Fusion expression vectors of Pearl protein and the 3 deletion mutants were constructed. The recombinant plasmids were induced by IPTG and the target proteins （Peatl, Peatl-△CD99,Peatl-△ND49 and Pearl-△ND108 ）were expressed obtained by AKTA and its thermal stability was analyzed. [Result] The research found that 3 deletion mutants have good thermal stability like Pearl. [Conclusion] The research demonstrated that the coexistence of NAC or UBA domains is not necessary to thermal stability of Pearl protein , and they may give the protein particular stability structure seperately.

Thermal stability and Judd-Ofelt analysis of optical properties of Er^(3+)-doped tellurite glasses

Er3＋-doped TeO2-ZnO-Na2O-B2O3-GeO2 （TZNBG） glasses were prepared by melt-quenching method. Differential scanning calorimetry （DSC） and thermal mechanical analysis （TMA） were used to calculate thermal parameters： crystallization temperature （Tx）, glass transition temperature （Tg） and thermal expansion （α）. Besides, Judd-Ofelt theory is applied to analyzing absorption spectra. Intensity parameters -λ （λ=2, 4, 6）, transition probabilities Aed, radiative lifetime τi, and branching ratios β of Er3＋ transitions were obtained. Emission cross-section σemis of 4I13/2→4I15/2 transition of Er3＋ was calculated according to the theory of McCumber. All of the parameters indicate that the thermal stability and optical properties of Er3＋-doped TZNBG glasses are improved effectively.

Microstructure, hardness evolution and thermal stability of binary Al-7Mg alloy processed by ECAP with intermediate annealing

A binary Al-7Mg alloy was processed by equal channel angular pressing （ECAP） at room temperature via route Bc, combined with intermediate annealing. After 6 passes, a high hardness of HV218 is achieved. Transmission electron microscopy （TEM） observations demonstrate that ECAP leads to a significant grain refinement and ultrafine grains down to 100-200 nm are developed after 5 or 6 passes. X-ray diffraction （XRD） analysis indicates that the major part of Mg atoms are in solid solution in the deformed material, and the possible strengthening effect of Mg solute atom clusters or precipitates is neglected. The high hardness of the 6 pass-treated materials comes mainly from grain boundary strengthening, which contributes about 41% to the total strength, while dislocations and Mg solid solution contribute about 24% and 35% to the remaining strength, respectively. Also, the thermal stability of this severely deformed material was investigated by hardness measurements. The material is relatively stable when annealed at a temperature lower than 250 ℃, while annealing at 300 ℃ leads to a rapid softening of the material.

Enhanced thermal stability and mechanical properties of high-temperature resistant Al-Cu alloy with Zr and Mn micro-alloying

The high temperature(HT)thermal stability and mechanical properties of Al-5%Cu(AC)and Al-5%Cu-0.2%Mn-0.2 Zr%(ACMZ)alloys from 573 to 673 K were systematically studied.The results displayed that micro-alloying additions of Zr and Mn elements have presented a significant role in stabilizing the main strengthening metastableθ′precipitates at a temperature as high as 573 K.Simultaneously,the HT tensile test demonstrated that ACMZ alloy retained their strength of(88.6±8.8)MPa,which was much higher than that of AC alloy((32.5±0.8)MPa)after the thermal exposure at 573 K for 200 h.Finally,the underlying mechanisms of strength and ductility enhancement mechanism of the ACMZ alloy at HT were discussed in detail.

Synthesis and thermal stability of a novel phosphorus-nitrogen containing intumescent flame retardant

A novel phosphorus-nitrogen containing intumescent flame retardant （P-N IFR） was prepared via the reaction of dichlor-opentate with N-methylaniline. The structure of the product was confirmed by ^1H NMR, ^31p NMR, MS and IR. TGA analysis showed it has effective thermal stability.

Effect of Ce on the thermal stability of the Ω phase in an Al-Cu-Mg-Ag alloy

This paper studies the effect of Ce on the thermal stability of the Ω phase in an Al-Cu-Mg-Ag alloy by TEM and tensile testing. It has been shown that Ce substantially increases the nucleation density of the Ω phase by acting as the heterogeneous nucleation center. Most impor-tantly,Ce improves the thermal stability of the Ω phase by decreasing the diffusion velocity of Cu atoms and increasing the energy barrier of the thickening ledge nucleation,thus improving the strength of the Al-Cu-Mg-Ag alloy at both ...

Effect of Mo content on the thermal stability of Ti-Mo-bearing ferritic steel

The effects of tempering holding time at 700℃on the morphology,mechanical properties,and behavior of nanoparticles in Ti-Mo ferritic steel with different Mo contents were analyzed using scanning electron microscopy and transmission electron microscopy.The equilibrium solid solution amounts of Mo,Ti,and C in ferritic steel at various temperatures were calculated,and changes in the sizes of nanoparticles over time at different Mo contents were analyzed.The experimental results and theoretical calculations were in good agreement with each other and showed that the size of nanoparticles in middle Mo content nano-ferrite(MNF)steel changed the least during aging.High Mo contents inhibited the maturation and growth of nanoparticles,but no obvious inhibitory effect was observed when the Mo content exceeded 0.37wt%.The tensile strength and yield strength continuously decreased with the tempering time.Analysis of the strengthening and toughening mechanisms showed that the different mechanical properties among the three different Mo content experiment steels were mainly determined by grain refinement strengthening(the difference range was 30-40 MPa)and precipitation strengthening(the difference range was 78-127 MPa).MNF steel displayed an ideal chemical ratio and the highest thermodynamic stability,whereas low Mo content nano-ferrite(LNF)steel and high Mo content nano-ferrite(HNF)steel displayed relatively similar thermodynamic stabilities.

Preparation and characterization of HMX/EVA/hBNNSs microcomposites with improved thermal stability and reduced sensitivity

Hexagonal boron nitride nanosheets(HBNNSs)have huge potential in the field of coating materials owing to their remarkable chemical stability,mechanical strength and thermal conductivity.Thin-layer hBNNSs were obtained by a liquid-phase exfoliation of h-BN powders and incorporated into EVA coatings for improving the safety performance of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX).HBNNSs and ethylene-vinyl acetate copolymer(EVA)were introduced to HMX by a solvent-slurry process.For comparison,the HMX/EVA and HMX/EVA/graphene(HMX/EVA/G)composites were also prepared by a similar process.The morphology,crystal form,surface element distribution,thermal decomposition property and impact sensitivity of HMX/EVA/hBNNSs composites were contrastively investigated.Results showed that as prepared HMX/EVA/hBNNSs composites were well coated with hBNNSs and EVA,and exhibited better thermal stability and lower impact sensitivity than that of HMX/EVA and HMX/EVA/G composites,suggesting superior performance of desensitization of hBNNSs in explosives.

Thermal Stability and Thermal Decomposition Kinetics of 1-Butyl-3-methylimidazolium Dicyanamide

Thermal stability and thermal decomposition kinetics of 1-butyl-3-methylimidazolium dicyanamide ([bmin+][N(CN) ]2-) were investigated using both isothermal and non-isothermal thermogravimetric analyses (TGA) under high pure nitrogen as carrier gas. The long-term thermogravimetric studies revealed that the highest temperature used should be 110 °C, at which [bmin+][N(CN)2-] lost less than 10% by mass in 10 hours. The non-isothermal activation energy values determined using Friedman and ASTM methods were (150±13) and (147±2) kJ·mol –1 , respectively. Multivariate non-linear-regression methods showed that expanded Fn and CnB models were the best fit models with highest correlation coefficient of 0.9994, and the apparent activation energies were consistent with iso-conversional methods.

Improving Thermal Stability of BaMgAl_(10)O_(17):Eu Phosphor

Heterogeneous precipitation method was used to prepared surface coating on self-made BaMgAl10O17 : Eu phosphor. Results illustrate that the coating film can be silicon dioxide in amorphous state with 50 nm in thickness. Photolumi-nescence results indicate that the coating layer presents an observable improved effect on the enhancement of thermal stability. When baked at 600℃for 1 h, the luminance of coated BAM keeps at 92% higher than that of uncoated BAM by 23% . This protective effect can be attributed to the high compact degree and uniformity of this amorphous SiO2 coating film which is served as a diffusion block layer to inbreak oxygen atom, thus releases the oxidation extent of Eu2 + effectively.

Influence of zirconium addition on microstructure,magnetic properties and thermal stability of nanocrystalline Nd_(12.3)Fe_(81.7)B_(6.0) alloy

Effect of Zr addition on microstructure, magnetic properties and thermal stability of Nd12.3Fe81.7-xZrxB6.0 (x=0-3.0) ribbons melt-spun and annealed was investigated. Magnetic measurement using vibrating sample magnetometer (VSM) revealed that Zr addition was significantly effective in improving the magnetic properties at room temperature. The intrinsic coercivity Hci of the optimally processed ribbons increased monotonically with increasing Zr content, from 751.7 kA/m for x=0 to 1005.3 kA/m for x=3.0. Unlike the coercivity, the remanence polarization Jr increased first with Zr addition, from 0.898 T up to 1.041 T at x=1.5, and then decreased with further Zr addition. The maximum energy product (BH)max behaved similarly, increasing from 103.1 kJ/m3 to a maximum of 175.2 kJ/m3 at x=1.5. Microstruc- ture studies using atomic force microscopy (AFM) and transmission electron microscopy (TEM) had shown a significant microstructure refinement with Zr addition. The absolute values of temperature coefficients of induction and coercivity were significantly increased with increasing Zr content, indicating that Zr was detrimental to thermal stability of the melt-spun Nd2Fe14B-type material.