Phase change materials(PCMs)have attracted much attention in the field of solar thermal utilization recently,due to their outstanding thermal energy storage performance.However,PCMs usually release their stored latent...Phase change materials(PCMs)have attracted much attention in the field of solar thermal utilization recently,due to their outstanding thermal energy storage performance.However,PCMs usually release their stored latent heat spontaneously as the temperature below the phase transition temperature,rendering thermal energy storage and release uncontrollable,thus hindering their practical application in time and space.Herein,we developed erythritol/sodium carboxymethylcellulose/tetrasodium ethylenediaminetetraacetate(ERY/CMC/EDTA-4Na)composite PCMs with novel spatiotemporal thermal energy storage properties,defined as spatiotemporal PCMs(STPCMs),which exhibit the capacity of thermal energy long-term storage and controllable release.Our results show that the composite PCMs are unable to lose latent heat due to spontaneous crystallization during cooling,but can controllably release thermal energy through cold crystallization during reheating.The cold-crystallization temperature and enthalpy of composite PCMs can be adjusted by proportional addition of EDTA-4Na to the composite.When the mass fractions of CMC and EDTA-4Na are both 10%,the composite PCMs can exhibit the optical coldcrystallization temperature of 51.7℃ and enthalpy of 178.1 J/g.The supercooled composite PCMs without latent heat release can be maintained at room temperature(10-25℃)for up to more than two months,and subsequently the stored latent heat can be controllably released by means of thermal triggering or heterogeneous nucleation.Our findings provide novel insights into the design and construction of new PCMs with spatiotemporal performance of thermal energy long-term storage and controllable release,and consequently open a new door for the development of advanced solar thermal utilization techniques on the basis of STPCMs.展开更多
Based on the phase change material (PCM) thermal characteristic,some testing methods such as differential scanning calorimeter (DSC) etc were used to select the low melting mixture of capric and lauric acid as PCM of ...Based on the phase change material (PCM) thermal characteristic,some testing methods such as differential scanning calorimeter (DSC) etc were used to select the low melting mixture of capric and lauric acid as PCM of phase change wallboard (PCW). The PCW room was established,and some contrast analysis of the storage and exchange thermal characteristic of PCW room and ordinary wall room were made under different conditions. The results show that the fluctuation of indoor air temperature in PCW room is smaller than that in ordinary room obviously. The exchange energy of PCM room with outdoor is less than that of ordinary wall room. In the winter condition,PCW room utilizes valley period electricity to storage energy in the night,while releases at peak period electricity in daytime,which can divert 40% of peak load. In the summer condition,PCW room can reduce the peak cooling load by 25% compared with ordinary wall room.展开更多
A new type of heat storage materials combining high temperature molten salts phases change latent heat thermal storage materials, PCM with porous metals sensible heat thermal storage materials was developed. The proce...A new type of heat storage materials combining high temperature molten salts phases change latent heat thermal storage materials, PCM with porous metals sensible heat thermal storage materials was developed. The process was expressed as following: firstly, it is necessary to heat up the molten salts phases change materials to molten; and then the porous metals are put into the molten bath; after being held for 13 h, the composite heat thermal storage materials lumps are taken out of the molten bath and cooled to atmospheric temperature; the last step is to electrodeposit a layer metal coat on the surface of the material lumps. The new type of heat storage material integrates the advantages of both solid sensible heat thermal storage materials and high temperature phases change latent heat thermal storage materials. The metal base heat storage materials enjoy some favorable characteristics such as higher heat charge discharge rate, higher heat storage density and better mechanical strength.展开更多
基金the financial support from the Joint Fund of the Yulin University and the Dalian National Laboratory for Clean Energy(YLU-DNL Fund 2021007)the National Nature Science Foundation of China(21903082 and 22273100)+2 种基金the Dalian Institute of Chemical Physics(DICP I202036,and I202218)the DNL Cooperation Fund,CAS(DNL202012)Liaoning Provincial Natural Science Foundation of China under grant 2022-MS-020。
文摘Phase change materials(PCMs)have attracted much attention in the field of solar thermal utilization recently,due to their outstanding thermal energy storage performance.However,PCMs usually release their stored latent heat spontaneously as the temperature below the phase transition temperature,rendering thermal energy storage and release uncontrollable,thus hindering their practical application in time and space.Herein,we developed erythritol/sodium carboxymethylcellulose/tetrasodium ethylenediaminetetraacetate(ERY/CMC/EDTA-4Na)composite PCMs with novel spatiotemporal thermal energy storage properties,defined as spatiotemporal PCMs(STPCMs),which exhibit the capacity of thermal energy long-term storage and controllable release.Our results show that the composite PCMs are unable to lose latent heat due to spontaneous crystallization during cooling,but can controllably release thermal energy through cold crystallization during reheating.The cold-crystallization temperature and enthalpy of composite PCMs can be adjusted by proportional addition of EDTA-4Na to the composite.When the mass fractions of CMC and EDTA-4Na are both 10%,the composite PCMs can exhibit the optical coldcrystallization temperature of 51.7℃ and enthalpy of 178.1 J/g.The supercooled composite PCMs without latent heat release can be maintained at room temperature(10-25℃)for up to more than two months,and subsequently the stored latent heat can be controllably released by means of thermal triggering or heterogeneous nucleation.Our findings provide novel insights into the design and construction of new PCMs with spatiotemporal performance of thermal energy long-term storage and controllable release,and consequently open a new door for the development of advanced solar thermal utilization techniques on the basis of STPCMs.
基金Project(50878133) supported by the National Natural Science Foundation of ChinaProject (2007R37) supported by Excellent Talents in Liaoning Province+1 种基金Project (2008S193) supported by the Key Laboratory Fund of Education Department in Liaoning ProvinceProject(1071211-1-00) supported by the Scientific and Technical Fund Project Subsidy of Shenyang Province
文摘Based on the phase change material (PCM) thermal characteristic,some testing methods such as differential scanning calorimeter (DSC) etc were used to select the low melting mixture of capric and lauric acid as PCM of phase change wallboard (PCW). The PCW room was established,and some contrast analysis of the storage and exchange thermal characteristic of PCW room and ordinary wall room were made under different conditions. The results show that the fluctuation of indoor air temperature in PCW room is smaller than that in ordinary room obviously. The exchange energy of PCM room with outdoor is less than that of ordinary wall room. In the winter condition,PCW room utilizes valley period electricity to storage energy in the night,while releases at peak period electricity in daytime,which can divert 40% of peak load. In the summer condition,PCW room can reduce the peak cooling load by 25% compared with ordinary wall room.
文摘A new type of heat storage materials combining high temperature molten salts phases change latent heat thermal storage materials, PCM with porous metals sensible heat thermal storage materials was developed. The process was expressed as following: firstly, it is necessary to heat up the molten salts phases change materials to molten; and then the porous metals are put into the molten bath; after being held for 13 h, the composite heat thermal storage materials lumps are taken out of the molten bath and cooled to atmospheric temperature; the last step is to electrodeposit a layer metal coat on the surface of the material lumps. The new type of heat storage material integrates the advantages of both solid sensible heat thermal storage materials and high temperature phases change latent heat thermal storage materials. The metal base heat storage materials enjoy some favorable characteristics such as higher heat charge discharge rate, higher heat storage density and better mechanical strength.
